uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
uses CONFIG_HAVE_ACPI_TABLES
uses CONFIG_HAVE_ACPI_RESUME
uses CONFIG_HAVE_PIRQ_TABLE
uses CONFIG_HAVE_FALLBACK_BOOT
uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_IRQ_SLOT_COUNT
uses CONFIG_MAX_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
uses CONFIG_ROM_PAYLOAD
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
uses CONFIG_STACK_SIZE
uses CONFIG_HEAP_SIZE
uses CONFIG_USE_OPTION_TABLE
uses CONFIG_LB_CKS_RANGE_START
uses CONFIG_LB_CKS_RANGE_END
uses CONFIG_LB_CKS_LOC
uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_MAINBOARD_VENDOR
uses CONFIG_MAINBOARD
uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses CONFIG_RAMBASE
uses CONFIG_TTYS0_BAUD
uses CONFIG_TTYS0_BASE
uses CONFIG_TTYS0_LCS
uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CROSS_COMPILE
uses CC
uses HOSTCC
uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_DEBUG
#uses CONFIG_CPU_OPT
uses CONFIG_IDE

## The default definitions are used for these
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_PAYLOAD_SIZE

## These are defined in target Config.lb, don't add here
uses CONFIG_USE_FALLBACK_IMAGE
uses CONFIG_ROM_SIZE
uses CONFIG_ROM_IMAGE_SIZE
uses CONFIG_FALLBACK_SIZE
uses COREBOOT_EXTRA_VERSION

## These are defined in mainboard Config.lb, don't add here
uses CONFIG_ROM_SECTION_SIZE
uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROMBASE
uses CONFIG_XIP_ROM_SIZE
uses CONFIG_XIP_ROM_BASE

###
### Build options
###

##
## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
default CONFIG_ROM_SIZE=2097152
default CONFIG_ROM_IMAGE_SIZE = 65536

##
## Build code for the fallback boot?
##
default CONFIG_HAVE_FALLBACK_BOOT=1
default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE


## Delay timer options
##
default CONFIG_UDELAY_TSC=1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1

##
## Build code to export a programmable irq routing table
##
default CONFIG_HAVE_PIRQ_TABLE=1
default CONFIG_IRQ_SLOT_COUNT=12

##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
default CONFIG_HAVE_MP_TABLE=1

## Build code to export ACPI tables?
default CONFIG_HAVE_ACPI_TABLES=1

##
## Build code to export a CMOS option table?
##
default CONFIG_HAVE_OPTION_TABLE=0

## CMOS checksum definitions (units == bytes)
## These must match the checksum record in cmos.layout
default CONFIG_LB_CKS_RANGE_START=128
default CONFIG_LB_CKS_RANGE_END=130
default CONFIG_LB_CKS_LOC=131

##
## Build code for SMP support
## Only worry about 2 micro processors
## NOTE: CONFIG_MAX_CPUS is the number of LOGICAL CPUs,
##		 so if CONFIG_LOGICAL_CPUS is 1, CONFIG_MAX_CPUS should be 4.
##
default CONFIG_SMP=1
default CONFIG_MAX_CPUS=2
default CONFIG_LOGICAL_CPUS=0
default CONFIG_MAX_PHYSICAL_CPUS=2

# VGA Console
# NOTE: to initialize VGA, need to copy the VGA option ROM from the factory BIOS
#	    to VGA.rom
default CONFIG_CONSOLE_VGA=0
default CONFIG_PCI_ROM_RUN=0

##
## Build code to setup a generic IOAPIC
##
default CONFIG_IOAPIC=1

##
## Motherboard identification
##
default CONFIG_MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT"
default CONFIG_MAINBOARD_VENDOR="Intel"
default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480

###
### coreboot layout values
###

##
## Use a small 8K stack
##
default CONFIG_STACK_SIZE=0x2000

##
## Use a small 16K heap
##
default CONFIG_HEAP_SIZE=0x4000

##
## CMOS settings not currently supported due to conflicts with factory BIOS
##
default CONFIG_USE_OPTION_TABLE = 0

##
## Coreboot C code runs at this location in RAM
##
default CONFIG_RAMBASE=0x00004000

##
## Load the payload from the ROM
##
default CONFIG_ROM_PAYLOAD = 1

###
### Defaults of options that you may want to override in the target config file
### 

##
## The default compiler
##
default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
default HOSTCC="gcc"

##
## Disable the gdb stub by default
## 
default CONFIG_GDB_STUB=0

##
## The Serial Console
##

# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1

## Select the serial console baud rate
default CONFIG_TTYS0_BAUD=115200
#default CONFIG_TTYS0_BAUD=57600
#default CONFIG_TTYS0_BAUD=38400
#default CONFIG_TTYS0_BAUD=19200
#default CONFIG_TTYS0_BAUD=9600
#default CONFIG_TTYS0_BAUD=4800
#default CONFIG_TTYS0_BAUD=2400
#default CONFIG_TTYS0_BAUD=1200

# Select the serial console base port
default CONFIG_TTYS0_BASE=0x3f8

# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
default CONFIG_TTYS0_LCS=0x3

##
### Select the coreboot loglevel
##
## EMERG      1   system is unusable               
## ALERT      2   action must be taken immediately 
## CRIT       3   critical conditions              
## ERR        4   error conditions                 
## WARNING    5   warning conditions               
## NOTICE     6   normal but significant condition 
## INFO       7   informational                    
## CONFIG_DEBUG      8   debug-level messages             
## SPEW       9   Way too many details             

## Request this level of debugging output
default  CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
default  CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8

##
## Select power on after power fail setting
default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"

## Things we may not have
default CONFIG_IDE=1

default CONFIG_DEBUG=1
# default CONFIG_CPU_OPT="-g"

### End Options.lb
#
# CBFS
#
#
default CONFIG_CBFS=1
end