uses HAVE_MP_TABLE uses HAVE_ACPI_TABLES uses HAVE_PIRQ_TABLE uses HAVE_FALLBACK_BOOT uses HAVE_OPTION_TABLE uses IRQ_SLOT_COUNT uses CONFIG_MAX_CPUS uses CONFIG_LOGICAL_CPUS uses CONFIG_MAX_PHYSICAL_CPUS uses CONFIG_IOAPIC uses CONFIG_SMP uses CONFIG_ROM_PAYLOAD uses CONFIG_COMPRESSED_PAYLOAD_LZMA uses CONFIG_PRECOMPRESSED_PAYLOAD uses STACK_SIZE uses HEAP_SIZE uses USE_OPTION_TABLE uses LB_CKS_RANGE_START uses LB_CKS_RANGE_END uses LB_CKS_LOC uses MAINBOARD_PART_NUMBER uses MAINBOARD_VENDOR uses MAINBOARD uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID uses _RAMBASE uses TTYS0_BAUD uses TTYS0_BASE uses TTYS0_LCS uses DEFAULT_CONSOLE_LOGLEVEL uses MAXIMUM_CONSOLE_LOGLEVEL uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL uses CONFIG_CONSOLE_SERIAL8250 uses CONFIG_UDELAY_TSC uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 uses HAVE_INIT_TIMER uses CONFIG_GDB_STUB uses CROSS_COMPILE uses CC uses HOSTCC uses OBJCOPY uses CONFIG_CHIP_NAME uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN uses DEBUG #uses CPU_OPT uses CONFIG_IDE ## The default definitions are used for these uses CONFIG_ROM_PAYLOAD_START uses PAYLOAD_SIZE ## These are defined in target Config.lb, don't add here uses USE_FALLBACK_IMAGE uses ROM_SIZE uses ROM_IMAGE_SIZE uses FALLBACK_SIZE uses COREBOOT_EXTRA_VERSION ## These are defined in mainboard Config.lb, don't add here uses ROM_SECTION_SIZE uses ROM_SECTION_OFFSET uses _ROMBASE uses XIP_ROM_SIZE uses XIP_ROM_BASE ### ### Build options ### ## ## ROM_SIZE is the size of boot ROM that this board will use. ## default ROM_SIZE=2097152 default ROM_IMAGE_SIZE = 65536 ## ## Build code for the fallback boot? ## default HAVE_FALLBACK_BOOT=1 default FALLBACK_SIZE=131072 ## Delay timer options ## default CONFIG_UDELAY_TSC=1 default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 ## ## Build code to export a programmable irq routing table ## default HAVE_PIRQ_TABLE=1 default IRQ_SLOT_COUNT=12 ## ## Build code to export an x86 MP table ## Useful for specifying IRQ routing values ## default HAVE_MP_TABLE=1 ## Build code to export ACPI tables? default HAVE_ACPI_TABLES=1 ## ## Build code to export a CMOS option table? ## default HAVE_OPTION_TABLE=0 ## CMOS checksum definitions (units == bytes) ## These must match the checksum record in cmos.layout default LB_CKS_RANGE_START=128 default LB_CKS_RANGE_END=130 default LB_CKS_LOC=131 ## ## Build code for SMP support ## Only worry about 2 micro processors ## NOTE: CONFIG_MAX_CPUS is the number of LOGICAL CPUs, ## so if CONFIG_LOGICAL_CPUS is 1, CONFIG_MAX_CPUS should be 4. ## default CONFIG_SMP=1 default CONFIG_MAX_CPUS=2 default CONFIG_LOGICAL_CPUS=0 default CONFIG_MAX_PHYSICAL_CPUS=2 # VGA Console # NOTE: to initialize VGA, need to copy the VGA option ROM from the factory BIOS # to VGA.rom default CONFIG_CONSOLE_VGA=0 default CONFIG_PCI_ROM_RUN=0 ## ## Build code to setup a generic IOAPIC ## default CONFIG_IOAPIC=1 ## ## Motherboard identification ## default MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT" default MAINBOARD_VENDOR="Intel" default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086 default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480 ### ### coreboot layout values ### ## ## Use a small 8K stack ## default STACK_SIZE=0x2000 ## ## Use a small 16K heap ## default HEAP_SIZE=0x4000 ## ## CMOS settings not currently supported due to conflicts with factory BIOS ## default USE_OPTION_TABLE = 0 ## ## Coreboot C code runs at this location in RAM ## default _RAMBASE=0x00004000 ## ## Load the payload from the ROM ## default CONFIG_ROM_PAYLOAD = 1 ### ### Defaults of options that you may want to override in the target config file ### ## ## The default compiler ## default CC="$(CROSS_COMPILE)gcc -m32" default HOSTCC="gcc" ## ## Disable the gdb stub by default ## default CONFIG_GDB_STUB=0 ## ## The Serial Console ## # To Enable the Serial Console default CONFIG_CONSOLE_SERIAL8250=1 ## Select the serial console baud rate default TTYS0_BAUD=115200 #default TTYS0_BAUD=57600 #default TTYS0_BAUD=38400 #default TTYS0_BAUD=19200 #default TTYS0_BAUD=9600 #default TTYS0_BAUD=4800 #default TTYS0_BAUD=2400 #default TTYS0_BAUD=1200 # Select the serial console base port default TTYS0_BASE=0x3f8 # Select the serial protocol # This defaults to 8 data bits, 1 stop bit, and no parity default TTYS0_LCS=0x3 ## ### Select the coreboot loglevel ## ## EMERG 1 system is unusable ## ALERT 2 action must be taken immediately ## CRIT 3 critical conditions ## ERR 4 error conditions ## WARNING 5 warning conditions ## NOTICE 6 normal but significant condition ## INFO 7 informational ## DEBUG 8 debug-level messages ## SPEW 9 Way too many details ## Request this level of debugging output default DEFAULT_CONSOLE_LOGLEVEL=8 ## At a maximum only compile in this level of debugging default MAXIMUM_CONSOLE_LOGLEVEL=8 ## ## Select power on after power fail setting default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" ## Things we may not have default CONFIG_IDE=1 default DEBUG=1 # default CPU_OPT="-g" default CONFIG_CHIP_NAME=1 ### End Options.lb end