chip soc/intel/alderlake

	# GPE configuration
	# Note that GPE events called out in ASL code rely on this
	# route. i.e. If this route changes then the affected GPE
	# offset bits also need to be changed.
	register "pmc_gpe0_dw0" = "GPP_B"
	register "pmc_gpe0_dw1" = "GPP_D"
	register "pmc_gpe0_dw2" = "GPP_E"

	# FSP configuration

	# Enable CNVi BT
	register "cnvi_bt_core" = "true"

	# Sagv Configuration
	register "sagv" = "SaGv_Enabled"

	# Enable DPTF
	register "dptf_enable" = "1"

	# eMMC HS400
	register "emmc_enable_hs400_mode" = "1"

	register "usb2_ports[0]" = "USB2_PORT_MID(OC3)"		# Type-C Port1
	register "usb2_ports[1]" = "USB2_PORT_MID(OC3)"		# Type-C Port2
	register "usb2_ports[2]" = "USB2_PORT_MID(OC3)"		# FPS connector
	register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)"	# M.2 WWAN
	register "usb2_ports[4]" = "USB2_PORT_MID(OC3)"		# USB3/2 Type A port1
	register "usb2_ports[5]" = "USB2_PORT_MID(OC1)"		# USB3/2 Type A port2
	register "usb2_ports[6]" = "USB2_PORT_MID(OC1)"		# USB3/2 Type A port3
	register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)"	# Type A/ M.2 WLAN
	register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)"	# Bluetooth

	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC3)"	# USB3/2 Type A port1
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)"	# USB3/2 Type A port2
	register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)"	# USB3/2 Type A port3
	register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# M.2 WWAN

	# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
	register "gen1_dec" = "0x00fc0801"
	register "gen2_dec" = "0x000c0201"
	# EC memory map range is 0x900-0x9ff
	register "gen3_dec" = "0x00fc0901"

	# Enable PCH PCIE RP 7 using CLK 3
	register "pch_pcie_rp[PCH_RP(7)]" = "{
		.clk_src = 3,
		.clk_req = 3,
		.flags = PCIE_RP_CLK_REQ_DETECT,
	}"

	# Enable PCH PCIE RP 9 using CLK 0
	register "pch_pcie_rp[PCH_RP(9)]" = "{
		.clk_src = 0,
		.clk_req = 0,
		.flags = PCIE_RP_CLK_REQ_DETECT,
	}"

	register "sata_salp_support" = "0"

	# Enable EDP in PortA
	register "ddi_portA_config" = "1"
	# Enable HDMI in Port B
	register "ddi_ports_config" = "{
		[DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC,
	}"

	# TCSS USB3
	register "tcss_aux_ori" = "4"
	register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_E20, .pad_auxn_dc = GPP_E21}"

	register "s0ix_enable" = "1"

	register "serial_io_i2c_mode" = "{
		[PchSerialIoIndexI2C0] = PchSerialIoPci,
		[PchSerialIoIndexI2C1] = PchSerialIoPci,
		[PchSerialIoIndexI2C2] = PchSerialIoPci,
		[PchSerialIoIndexI2C3] = PchSerialIoPci,
		[PchSerialIoIndexI2C4] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C5] = PchSerialIoPci,
	}"

	register "serial_io_gspi_mode" = "{
		[PchSerialIoIndexGSPI0] = PchSerialIoPci,
		[PchSerialIoIndexGSPI1] = PchSerialIoDisabled,
		[PchSerialIoIndexGSPI2] = PchSerialIoDisabled,
		[PchSerialIoIndexGSPI3] = PchSerialIoDisabled,
	}"

	register "serial_io_gspi_cs_mode" = "{
		[PchSerialIoIndexGSPI0] = 0,
		[PchSerialIoIndexGSPI1] = 0,
		[PchSerialIoIndexGSPI2] = 0,
		[PchSerialIoIndexGSPI3] = 0,
	}"

	register "serial_io_gspi_cs_state" = "{
		[PchSerialIoIndexGSPI0] = 0,
		[PchSerialIoIndexGSPI1] = 0,
		[PchSerialIoIndexGSPI2] = 0,
		[PchSerialIoIndexGSPI3] = 0,
	}"

	register "serial_io_uart_mode" = "{
		[PchSerialIoIndexUART0] = PchSerialIoSkipInit,
		[PchSerialIoIndexUART1] = PchSerialIoDisabled,
		[PchSerialIoIndexUART2] = PchSerialIoDisabled,
	}"

	# HD Audio
	register "pch_hda_dsp_enable" = "1"
	register "pch_hda_idisp_link_tmode" = "HDA_TMODE_8T"
	register "pch_hda_idisp_link_frequency" = "HDA_LINKFREQ_96MHZ"
	register "pch_hda_idisp_codec_enable" = "1"

	register "cnvi_bt_audio_offload" = "true"

	# set EPP to 45%: 45 * 256/100 = 115 = 0x73
	register "enable_energy_perf_pref" = "true"
	register "energy_perf_pref_value" = "0x73"

	# Intel Common SoC Config
	register "common_soc_config" = "{
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[1] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[2] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[3] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
		},
	}"

	# Configure external V1P05/Vnn/VnnSx Rails
	register "ext_fivr_settings" = "{
		.configure_ext_fivr = 1,
		.v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX,
		.vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
		.vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
		.v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
		.vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
		.v1p05_voltage_mv = 1050,
		.vnn_voltage_mv = 780,
		.vnn_sx_voltage_mv = 1050,
		.v1p05_icc_max_ma = 500,
		.vnn_icc_max_ma = 500,
	}"

	register "skip_mbp_hob" = "1"

	device domain 0 on
		device ref igpu on end
		device ref dtt on
			chip drivers/intel/dptf

				## sensor information
				register "options.tsr[0].desc" = ""Ambient""
				register "options.tsr[1].desc" = ""Battery""
				register "options.tsr[2].desc" = ""DDR""
				register "options.tsr[3].desc" = ""Skin""
				register "options.tsr[4].desc" = ""VR""

				## Active Policy
				# TODO: below values are initial reference values only
				register "policies.active" = "{
					[0] = {
							.target = DPTF_CPU,
							.thresholds = {
								TEMP_PCT(95, 90),
								TEMP_PCT(90, 80),
							}
						},
					[1] = {
							.target = DPTF_TEMP_SENSOR_0,
							.thresholds = {
								TEMP_PCT(80, 90),
								TEMP_PCT(70, 80),
							}
						}
				}"

				## Passive Policy
				# TODO: below values are initial reference values only
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU,		CPU,	       95, 10000),
					[1] = DPTF_PASSIVE(CPU,		TEMP_SENSOR_0, 85, 50000),
					[2] = DPTF_PASSIVE(CHARGER,	TEMP_SENSOR_1, 85, 50000),
					[3] = DPTF_PASSIVE(CPU,		TEMP_SENSOR_2, 85, 50000),
					[4] = DPTF_PASSIVE(CPU,		TEMP_SENSOR_3, 85, 50000),
					[5] = DPTF_PASSIVE(CPU,		TEMP_SENSOR_4, 85, 50000),
				}"

				## Critical Policy
				# TODO: below values are initial reference values only
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,	  105, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 95, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 95, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 95, SHUTDOWN),
					[4] = DPTF_CRITICAL(TEMP_SENSOR_3, 95, SHUTDOWN),
					[5] = DPTF_CRITICAL(TEMP_SENSOR_4, 95, SHUTDOWN),
				}"

				## Power Limits Control
				register "controls.power_limits" = "{
					.pl1 = {
							.min_power = 3000,
							.max_power = 15000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 200,
					},
					.pl2 = {
							.min_power = 25000,
							.max_power = 35000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 1000,
					}
				}"

				## Charger Performance Control (Control, mA)
				register "controls.charger_perf" = "{
					[0] = { 255, 3000 },
					[1] = {  24, 1500 },
					[2] = {  16, 1000 },
					[3] = {   8,  500 }
				}"

				## Fan Performance Control (Percent, Speed, Noise, Power)
				register "controls.fan_perf" = "{
					[0] = {  90, 6700, 220, 2200, },
					[1] = {  80, 5800, 180, 1800, },
					[2] = {  70, 5000, 145, 1450, },
					[3] = {  60, 4900, 115, 1150, },
					[4] = {  50, 3838,  90,  900, },
					[5] = {  40, 2904,  55,  550, },
					[6] = {  30, 2337,  30,  300, },
					[7] = {  20, 1608,  15,  150, },
					[8] = {  10,  800,  10,  100, },
					[9] = {   0,    0,   0,   50, }
				}"

				## Fan options
				register "options.fan.fine_grained_control" = "1"
				register "options.fan.step_size" = "2"

				device generic 0 alias dptf_policy on end
			end
		end
		device ref ipu on
			chip drivers/intel/mipi_camera
				register "acpi_uid" = "0x50000"
				register "acpi_name" = ""IPU0""
				register "device_type" = "INTEL_ACPI_CAMERA_CIO2"

				register "cio2_num_ports" = "2"
				register "cio2_lanes_used" = "{2,2}"
				register "cio2_lane_endpoint[0]" = ""^I2C5.CAM1""
				register "cio2_lane_endpoint[1]" = ""^I2C1.CAM0""
				register "cio2_prt[0]" = "2"
				register "cio2_prt[1]" = "1"
				device generic 0 on end
			end
		end
		device ref crashlog off end
		device ref tcss_xhci on end
		device ref xhci on
			chip drivers/usb/acpi
				register "desc" = ""Root Hub""
				register "type" = "UPC_TYPE_HUB"
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port10 on end
					end
				end
			end
		end
		device ref cnvi_wifi on
			chip drivers/wifi/generic
				register "wake" = "GPE0_PME_B0"
				device generic 0 on end
			end
		end
		device ref i2c0 on end
		device ref i2c1 on
			chip drivers/intel/mipi_camera
				register "acpi_hid" = ""OVTI5675""
				register "acpi_uid" = "0"
				register "acpi_name" = ""CAM0""
				register "chip_name" = ""Ov 5675 Camera""
				register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"

				register "ssdb.lanes_used" = "2"
				register "ssdb.vcm_type" = "0x0C"
				register "vcm_name" = ""VCM0""
				register "num_freq_entries" = "1"
				register "link_freq[0]" = "450000000"
				register "remote_name" = ""IPU0""

				register "has_power_resource" = "1"
				#Controls
				register "clk_panel.clks[0].clknum" = "0" #IMGCLKOUT_0
				register "clk_panel.clks[0].freq" = "1" #19.2 Mhz
				register "gpio_panel.gpio[0].gpio_num" = "GPP_B23" #power_enable
				register "gpio_panel.gpio[1].gpio_num" = "GPP_R5" #reset

				#_ON
				register "on_seq.ops_cnt" = "4"
				register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
				register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 2)"
				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 1)"
				register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 1)"

				#_OFF
				register "off_seq.ops_cnt" = "3"
				register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
				register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
				register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

				device i2c 36 on end
			end
			chip drivers/intel/mipi_camera
				register "acpi_uid" = "3"
				register "acpi_name" = ""VCM0""
				register "chip_name" = ""DW AF VCM""
				register "device_type" = "INTEL_ACPI_CAMERA_VCM"

				register "pr0" = ""\\_SB.PCI0.I2C1.CAM0.PRIC""
				register "vcm_compat" = ""dongwoon,dw9714""

				device i2c 0C on end
			end
		end
		device ref i2c2 on end
		device ref i2c3 on end
		device ref heci1 on end
		device ref sata off end
		device ref i2c5 on
			chip drivers/intel/mipi_camera
				register "acpi_hid" = ""OVTI5675""
				register "acpi_uid" = "0"
				register "acpi_name" = ""CAM1""
				register "chip_name" = ""Ov 5675 Camera""
				register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"

				register "ssdb.lanes_used" = "2"
				register "num_freq_entries" = "1"
				register "link_freq[0]" = "450000000"
				register "remote_name" = ""IPU0""

				register "has_power_resource" = "1"
				#Controls
				register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_1
				register "clk_panel.clks[0].freq" = "1" #19.2 Mhz
				register "gpio_panel.gpio[0].gpio_num" = "GPP_E16" #power_enable
				register "gpio_panel.gpio[1].gpio_num" = "GPP_E15" #reset

				#_ON
				register "on_seq.ops_cnt" = "4"
				register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
				register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 2)"
				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 1)"
				register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 1)"

				#_OFF
				register "off_seq.ops_cnt" = "3"
				register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
				register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
				register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

				device i2c 36 on end
			end
		end
		device ref pcie_rp7 on end
		device ref pcie_rp9 on end
		device ref uart0 on end
		device ref gspi0 on end
		device ref p2sb on end
		device ref emmc on end
		device ref ish on end
		device ref ufs on end
		device ref hda on
			chip drivers/intel/soundwire
				device generic 0 on
					chip drivers/soundwire/alc711
						# SoundWire Link 0 ID 1
						register "desc" = ""Headset Codec""
						device generic 0.1 on end
					end
				end
			end
		end
		device ref smbus on end
	end
end