chip soc/intel/tigerlake
	# BitMask where bits [3:0] are Controller 0 Channel [3:0] and
	# bits [7:4] are Controller 1 Channel [3:0].
	# Enable Command Mirroring for controller 0 channel 0 and 1,
	# and controller 1 channel 0 and 1.
	register "CmdMirror" = "0x00000033"

	register "TcssAuxOri" = "1"
	register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E10, .pad_auxn_dc = GPP_E13}"

	device domain 0 on
		device ref ipu on end # IPU
		device ref i2c0 on
			chip drivers/i2c/generic
				register "hid" = ""10EC5682""
				register "name" = ""RT58""
				register "desc" = ""Headset Codec""
				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_R5)"
				# Set the jd_src to RT5668_JD1 for jack detection
				register "property_count" = "1"
				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
				register "property_list[0].name" = ""realtek,jd-src""
				register "property_list[0].integer" = "1"
				device i2c 1a on
				end
			end
			chip drivers/i2c/max98373
				register "vmon_slot_no" = "0"
				register "imon_slot_no" = "1"
				register "uid" = "0"
				register "desc" = ""Right Speaker Amp""
				register "name" = ""MAXR""
				device i2c 31 on
					probe AUDIO MAX98373_ALC5682I_I2S_UP4
				end
			end
			chip drivers/i2c/max98373
				register "vmon_slot_no" = "2"
				register "imon_slot_no" = "3"
				register "uid" = "1"
				register "desc" = ""Left Speaker Amp""
				register "name" = ""MAXL""
				device i2c 32 on
					probe AUDIO MAX98373_ALC5682I_I2S_UP4
				end
			end
		end
		device ref i2c1 on
			chip drivers/i2c/hid
				register "generic.hid" = ""ELAN9004""
				register "generic.desc" = ""ELAN Touchscreen""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)"
				register "generic.detect" = "1"
				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)"
				register "generic.reset_delay_ms" = "20"
				register "generic.reset_off_delay_ms" = "2"
				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_F16)"
				register "generic.enable_delay_ms" = "10"
				register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E3)"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 10 on end
			end
		end
		device ref i2c5 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)"
				register "wake" = "GPE0_DW2_15"
				register "detect" = "1"
				device i2c 15 on end
			end
		end
		device ref pch_espi on
			chip ec/google/chromeec
				use conn0 as mux_conn[0]
				use conn1 as mux_conn[1]
				device pnp 0c09.0 on end
			end
		end
		device ref hda on
			probe AUDIO MAX98357_ALC5682I_I2S
			probe AUDIO MAX98373_ALC5682I_I2S
			probe AUDIO MAX98373_ALC5682_SNDW
			probe AUDIO MAX98373_ALC5682I_I2S_UP4
			probe AUDIO MAX98360_ALC5682I_I2S
			probe AUDIO RT1011_ALC5682I_I2S
		end

		device ref pcie_rp7 off
			# Disable WLAN PCIE 7
			register "PcieRpLtrEnable[6]" = "0"
			register "PcieClkSrcUsage[1]" = "PCIE_CLK_NOTUSED"
			register "PcieRpSlotImplemented[6]" = "1"
		end
		device ref pcie_rp8 off
			# Disable SD Card PCIE 8
			register "PcieRpLtrEnable[7]" = "0"
			register "PcieRpHotPlug[7]" = "0"
			register "PcieClkSrcUsage[3]" = "PCIE_CLK_NOTUSED"
			# override-devicetree rules say it's only
			# the same device if it has the same probes:
			probe DB_SD SD_GL9755S
			probe DB_SD SD_RTS5261
			probe DB_SD SD_RTS5227S
			probe DB_SD SD_GL9750
			probe DB_SD SD_OZ711LV2LN
		end
		device ref pcie_rp9 on
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)"
				register "srcclk_pin" = "0"
				device generic 0 on end
			end
		end
		device ref pmc hidden
			# The pmc_mux chip driver is a placeholder for the
			# PMC.MUX device in the ACPI hierarchy.
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						use usb2_port5 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
					chip drivers/intel/pmc_mux/conn
						use usb2_port3 as usb2_port
						use tcss_usb3_port2 as usb3_port
						# SBU is fixed, HSL follows CC
						register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL"
						device generic 1 alias conn1 on end
					end
				end
			end
		end
		device ref north_xhci on
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "group" = "ACPI_PLD_GROUP(3, 2)"
						device ref tcss_usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C1 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "group" = "ACPI_PLD_GROUP(2, 2)"
						device ref tcss_usb3_port2 on
							probe DB_USB USB3_ACTIVE
						end
					end
				end
			end
		end
		device ref south_xhci on
			register "usb2_ports" = "{
				[2] = USB2_PORT_TYPE_C(OC_SKIP),	// Type-A / Type-C Port 1
				[4] = USB2_PORT_TYPE_C(OC_SKIP),	// Type-A / Type-C Port 0
			}"

			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A1 (DB)""
						register "type" = "UPC_TYPE_A"
						register "group" = "ACPI_PLD_GROUP(1, 1)"
						device ref usb2_port2 on
							probe DB_USB USB3_ACTIVE
						end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C1 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "group" = "ACPI_PLD_GROUP(2, 1)"
						device ref usb2_port3 on
							probe DB_USB USB3_ACTIVE
						end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "group" = "ACPI_PLD_GROUP(3, 1)"
						device ref usb2_port5 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A1 (DB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "group" = "ACPI_PLD_GROUP(1, 2)"
						device ref usb3_port2 on
							probe DB_USB USB3_ACTIVE
						end
					end
				end
			end
		end
	end
end