chip soc/intel/apollolake

	register "common_soc_config" = "{
		.gspi[0] = {
			.speed_mhz = 1,
			.early_init = 1,
		},
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 152,
			.fall_time_ns = 30,
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 60,
			.fall_time_ns = 20,
			.data_hold_time_ns = 350,
		},
		.i2c[6] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 70,
			.fall_time_ns = 127,
			.data_hold_time_ns = 350,
		},
		.i2c[7] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 30,
			.fall_time_ns = 127,
			.data_hold_time_ns = 350,
		},
	}"
	device domain 0 on
		device pci 16.0 on
			chip drivers/i2c/hid
				register "generic.hid" = ""WCOM50C1""
				register "generic.desc" = ""WCOM Digitizer""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_139_IRQ)"
				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_140)"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x1"
				device i2c 0x9 on end
			end
		end	# - I2C 0
		device pci 17.1 on
			chip drivers/i2c/generic
				register "hid" = ""10EC5682""
				register "name" = ""RT58""
				register "desc" = ""Realtek RT5682""
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
				register "probed" = "1"
				register "property_count" = "1"
				# Set the jd_src to RT5668_JD1 for jack detection
				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
				register "property_list[0].name" = ""realtek,jd-src""
				register "property_list[0].integer" = "1"
				device i2c 1a on end
			end
		end	# - I2C 5
		device pci 17.2 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPIO_135_IRQ)"
				register "wake" = "GPE0_DW3_27"
				register "probed" = "1"
				device i2c 15 on end
			end
		end	# - I2C 6
		device pci 17.3 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0001""
				register "desc" = ""ELAN Touchscreen""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_212_IRQ)"
				register "probed" = "1"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
				register "reset_delay_ms" = "20"
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
				register "enable_delay_ms" = "1"
				register "has_power_resource" = "1"
				device i2c 10 on end
			end
		end	# - I2C 7
	end
end