chip soc/intel/cannonlake register "tdp_pl1_override" = "15" register "tdp_pl2_override" = "51" register "SerialIoDevMode" = "{ [PchSerialIoIndexI2C0] = PchSerialIoPci, [PchSerialIoIndexI2C1] = PchSerialIoPci, [PchSerialIoIndexI2C2] = PchSerialIoPci, [PchSerialIoIndexI2C3] = PchSerialIoPci, [PchSerialIoIndexI2C4] = PchSerialIoPci, [PchSerialIoIndexI2C5] = PchSerialIoPci, [PchSerialIoIndexSPI0] = PchSerialIoPci, [PchSerialIoIndexSPI1] = PchSerialIoPci, [PchSerialIoIndexSPI2] = PchSerialIoDisabled, [PchSerialIoIndexUART0] = PchSerialIoSkipInit, [PchSerialIoIndexUART1] = PchSerialIoDisabled, [PchSerialIoIndexUART2] = PchSerialIoDisabled, }" # Intel Common SoC Config #+-------------------+---------------------------+ #| Field | Value | #+-------------------+---------------------------+ #| GSPI0 | cr50 TPM. Early init is | #| | required to set up a BAR | #| | for TPM communication | #| | before memory is up | #| I2C0 | Touchpad | #| I2C1 | Touch screen | #| I2C4 | Audio | #+-------------------+---------------------------+ register "common_soc_config" = "{ .gspi[0] = { .speed_mhz = 1, .early_init = 1, }, .i2c[0] = { .speed = I2C_SPEED_FAST, }, .i2c[1] = { .speed = I2C_SPEED_FAST, }, .i2c[4] = { .speed = I2C_SPEED_FAST, }, }" # GPIO for SD card detect register "sdcard_cd_gpio" = "vSD3_CD_B" # Enable eMMC HS400 register "ScsEmmcHs400Enabled" = "1" # EMMC Tx CMD Delay # Refer to EDS-Vol2-14.3.7. # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" # EMMC TX DATA Delay 1 # Refer to EDS-Vol2-14.3.8. # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x911" # EMMC TX DATA Delay 2 # Refer to EDS-Vol2-14.3.9. # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C262828" # EMMC RX CMD/DATA Delay 1 # Refer to EDS-Vol2-14.3.10. # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C16583b" # EMMC RX CMD/DATA Delay 2 # Refer to EDS-Vol2-14.3.12. # [17:16] stands for Rx Clock before Output Buffer, # 00: Rx clock after output buffer, # 01: Rx clock before output buffer, # 10: Automatic selection based on working mode. # 11: Reserved # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1001D" # EMMC Rx Strobe Delay # Refer to EDS-Vol2-14.3.11. # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1515" device domain 0 on device pci 15.0 on chip drivers/i2c/generic register "hid" = ""ELAN0000"" register "desc" = ""ELAN Touchpad"" register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_A21_IRQ)" register "wake" = "GPE0_DW0_21" register "probed" = "1" device i2c 15 on end end chip drivers/i2c/hid register "generic.hid" = ""PNP0C50"" register "generic.desc" = ""Synaptics Touchpad"" register "generic.irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_A21_IRQ)" register "generic.wake" = "GPE0_DW0_21" register "generic.probed" = "1" register "hid_desc_reg_offset" = "0x20" device i2c 0x2c on end end end # I2C #0 device pci 15.1 on chip drivers/i2c/generic register "hid" = ""ELAN0001"" register "desc" = ""ELAN Touchscreen"" register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" register "probed" = "1" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" register "reset_delay_ms" = "100" register "reset_off_delay_ms" = "5" register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D9)" register "enable_delay_ms" = "10" register "enable_off_delay_ms" = "1" register "has_power_resource" = "1" device i2c 49 on end end chip drivers/i2c/generic register "hid" = ""RAYD0001"" register "desc" = ""Raydium Touchscreen"" register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" register "probed" = "1" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" register "reset_delay_ms" = "1" register "reset_off_delay_ms" = "2" register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D9)" register "enable_delay_ms" = "10" register "enable_off_delay_ms" = "1" register "has_power_resource" = "1" device i2c 39 on end end chip drivers/generic/gpio_keys register "name" = ""PENH"" register "gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A8)" register "key.wake" = "GPE0_DW0_08" register "key.wakeup_event_action" = "EV_ACT_ASSERTED" register "key.dev_name" = ""EJCT"" register "key.linux_code" = "SW_PEN_INSERTED" register "key.linux_input_type" = "EV_SW" register "key.label" = ""pen_eject"" device generic 0 on end end end # I2C #1 device pci 15.2 off end # I2C #2 unused device pci 15.3 off end # I2C #3 unused device pci 19.0 on chip drivers/i2c/generic register "hid" = ""10EC5682"" register "name" = ""RT58"" register "desc" = ""Realtek RT5682"" register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)" register "property_count" = "1" # Set the jd_src to RT5668_JD1 for jack detection register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" register "property_list[0].name" = ""realtek,jd-src"" register "property_list[0].integer" = "1" device i2c 1a on end end end #I2C #4 device pci 1a.0 on end # eMMC device pci 1e.3 off end # GSPI #1 unused end end