chip soc/intel/cannonlake # Auto-switch between X4 NVMe and X2 NVMe. register "TetonGlacierMode" = "1" register "SerialIoDevMode" = "{ [PchSerialIoIndexI2C0] = PchSerialIoDisabled, [PchSerialIoIndexI2C1] = PchSerialIoDisabled, [PchSerialIoIndexI2C2] = PchSerialIoPci, [PchSerialIoIndexI2C3] = PchSerialIoPci, [PchSerialIoIndexI2C4] = PchSerialIoPci, [PchSerialIoIndexI2C5] = PchSerialIoPci, [PchSerialIoIndexSPI0] = PchSerialIoPci, [PchSerialIoIndexSPI1] = PchSerialIoPci, [PchSerialIoIndexSPI2] = PchSerialIoDisabled, [PchSerialIoIndexUART0] = PchSerialIoSkipInit, [PchSerialIoIndexUART1] = PchSerialIoDisabled, [PchSerialIoIndexUART2] = PchSerialIoDisabled, }" # USB configuration register "usb2_ports[0]" = "{ .enable = 1, .ocpin = OC2, .tx_bias = USB2_BIAS_0MV, .tx_emp_enable = USB2_PRE_EMP_ON, .pre_emp_bias = USB2_BIAS_11P25MV, .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, }" # Type-A Port 0 register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port 0 register "usb2_ports[2]" = "{ .enable = 1, .ocpin = OC3, .tx_bias = USB2_BIAS_0MV, .tx_emp_enable = USB2_PRE_EMP_ON, .pre_emp_bias = USB2_BIAS_28P15MV, .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, }" # Type-A Port 1 register "usb2_ports[3]" = "USB2_PORT_EMPTY" register "usb2_ports[4]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port 1 register "usb2_ports[5]" = "USB2_PORT_LONG(OC_SKIP)" # USB cam register "usb2_ports[6]" = "USB2_PORT_EMPTY" register "usb2_ports[7]" = "USB2_PORT_EMPTY" register "usb2_ports[8]" = "USB2_PORT_EMPTY" register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # BT register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port 0 register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port 1 register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port 1 register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port 0 register "usb3_ports[4]" = "USB3_PORT_EMPTY" register "usb3_ports[5]" = "USB3_PORT_EMPTY" # Bitmap for Wake Enable on USB attach/detach register "usb2_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(1) | \ USB_PORT_WAKE_ENABLE(3)" register "usb3_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(1) | \ USB_PORT_WAKE_ENABLE(2)" # Enable eMMC HS400 register "ScsEmmcHs400Enabled" = "1" # EMMC Tx CMD Delay # Refer to EDS-Vol2-14.3.7. # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" # EMMC TX DATA Delay 1 # Refer to EDS-Vol2-14.3.8. # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x911" # EMMC TX DATA Delay 2 # Refer to EDS-Vol2-14.3.9. # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C262828" # EMMC RX CMD/DATA Delay 1 # Refer to EDS-Vol2-14.3.10. # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C16583b" # EMMC RX CMD/DATA Delay 2 # Refer to EDS-Vol2-14.3.12. # [17:16] stands for Rx Clock before Output Buffer, # 00: Rx clock after output buffer, # 01: Rx clock before output buffer, # 10: Automatic selection based on working mode. # 11: Reserved # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1001D" # EMMC Rx Strobe Delay # Refer to EDS-Vol2-14.3.11. # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1515" # Intel Common SoC Config #+-------------------+---------------------------+ #| Field | Value | #+-------------------+---------------------------+ #| GSPI0 | cr50 TPM. Early init is | #| | required to set up a BAR | #| | for TPM communication | #| | before memory is up | #| I2C0 | ALC 1015 | #| I2C2 | Lvds | #| I2C3 | Touchscreen | #| I2C4 | RT5682 | #+-------------------+---------------------------+ register "common_soc_config" = "{ .gspi[0] = { .speed_mhz = 1, .early_init = 1, }, .i2c[0] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 60, .fall_time_ns = 60, }, .i2c[2] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 60, .fall_time_ns = 60, }, .i2c[3] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 60, .fall_time_ns = 60, }, .i2c[4] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 60, .fall_time_ns = 60, }, }" # PCIe port 11 (x2) for NVMe hybrid storage devices register "PcieRpEnable[10]" = "1" register "PcieRpLtrEnable[10]" = "1" # Uses CLK SRC 0 register "PcieClkSrcUsage[0]" = "6" register "PcieClkSrcClkReq[0]" = "0" # SATA port 1 Gen3 Strength # Port1 Tx De-Emphasis = 20*log(0x20/64) = -6dB register "sata_port[1].TxGen3DeEmphEnable" = "1" register "sata_port[1].TxGen3DeEmph" = "0x20" device domain 0 on device pci 04.0 on chip drivers/intel/dptf ## Active Policy register "policies.active[0]" = "{.target=DPTF_CPU, .thresholds={TEMP_PCT(90, 85), TEMP_PCT(85, 75), TEMP_PCT(80, 65), TEMP_PCT(75, 55), TEMP_PCT(70, 45),}}" register "policies.active[1]" = "{.target=DPTF_TEMP_SENSOR_0, .thresholds={TEMP_PCT(50, 85), TEMP_PCT(47, 75), TEMP_PCT(45, 65), TEMP_PCT(42, 55), TEMP_PCT(39, 45),}}" ## Passive Policy register "policies.passive[0]" = "DPTF_PASSIVE(CPU, CPU, 93, 5000)" register "policies.passive[1]" = "DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 65, 6000)" ## Critical Policy register "policies.critical[0]" = "DPTF_CRITICAL(CPU, 100, SHUTDOWN)" register "policies.critical[1]" = "DPTF_CRITICAL(TEMP_SENSOR_0, 75, SHUTDOWN)" ## Power Limits Control # PL1 is fixed at 15W, avg over 28-32s interval # 25-64W PL2 in 1000mW increments, avg over 28-32s interval register "controls.power_limits.pl1" = "{ .min_power = 15000, .max_power = 15000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 200,}" register "controls.power_limits.pl2" = "{ .min_power = 25000, .max_power = 64000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 1000,}" ## Charger Performance Control (Control, mA) register "controls.charger_perf[0]" = "{ 255, 1700 }" register "controls.charger_perf[1]" = "{ 24, 1500 }" register "controls.charger_perf[2]" = "{ 16, 1000 }" register "controls.charger_perf[3]" = "{ 8, 500 }" ## Fan Performance Control (Percent, Speed, Noise, Power) register "controls.fan_perf[0]" = "{ 90, 6700, 220, 2200, }" register "controls.fan_perf[1]" = "{ 80, 5800, 180, 1800, }" register "controls.fan_perf[2]" = "{ 70, 5000, 145, 1450, }" register "controls.fan_perf[3]" = "{ 60, 4900, 115, 1150, }" register "controls.fan_perf[4]" = "{ 50, 3838, 90, 900, }" register "controls.fan_perf[5]" = "{ 40, 2904, 55, 550, }" register "controls.fan_perf[6]" = "{ 30, 2337, 30, 300, }" register "controls.fan_perf[7]" = "{ 20, 1608, 15, 150, }" register "controls.fan_perf[8]" = "{ 10, 800, 10, 100, }" register "controls.fan_perf[9]" = "{ 0, 0, 0, 50, }" # Fan options register "options.fan.fine_grained_control" = "1" register "options.fan.step_size" = "2" device generic 0 on end end end # DPTF 0x1903 device pci 14.0 on chip drivers/usb/acpi device usb 0.0 on chip drivers/usb/acpi register "desc" = ""USB2 Type-A Port 0"" register "type" = "UPC_TYPE_A" register "group" = "ACPI_PLD_GROUP(1, 1)" device usb 2.0 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port 0"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "group" = "ACPI_PLD_GROUP(2, 1)" device usb 2.1 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-A Port 1"" register "type" = "UPC_TYPE_A" register "group" = "ACPI_PLD_GROUP(1, 2)" device usb 2.2 on end end chip drivers/usb/acpi device usb 2.3 off end end chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port 1"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "group" = "ACPI_PLD_GROUP(2, 2)" device usb 2.4 on end end chip drivers/usb/acpi register "desc" = ""Camera"" register "type" = "UPC_TYPE_INTERNAL" device usb 2.5 on end end chip drivers/usb/acpi device usb 2.6 off end end chip drivers/usb/acpi register "desc" = ""USB3 Type-A Port 0"" register "type" = "UPC_TYPE_USB3_A" register "group" = "ACPI_PLD_GROUP(1, 1)" device usb 3.0 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-A Port 1"" register "type" = "UPC_TYPE_USB3_A" register "group" = "ACPI_PLD_GROUP(1, 2)" device usb 3.1 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port 1"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "group" = "ACPI_PLD_GROUP(2, 2)" device usb 3.2 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port 0"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "group" = "ACPI_PLD_GROUP(2, 1)" device usb 3.3 on end end chip drivers/usb/acpi device usb 3.4 off end end chip drivers/usb/acpi device usb 3.5 off end end end end end # USB xHCI device pci 14.5 off end # SDCard device pci 15.0 on chip drivers/i2c/generic register "hid" = ""10EC1015"" register "desc" = ""Realtek SPK AMP L"" register "uid" = "0" device i2c 28 on end end chip drivers/i2c/generic register "hid" = ""10EC1015"" register "desc" = ""Realtek SPK AMP R"" register "uid" = "1" device i2c 29 on end end end # I2C #0 ALC1015 device pci 15.1 off end # I2C #1 device pci 15.2 on end # I2C #2 LVDS device pci 15.3 on chip drivers/i2c/hid register "generic.hid" = ""WDHT2002"" register "generic.desc" = ""WDT Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A20_IRQ)" register "generic.probed" = "1" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" register "generic.reset_delay_ms" = "100" register "generic.has_power_resource" = "1" register "generic.disable_gpio_export_in_crs" = "1" register "hid_desc_reg_offset" = "0x20" device i2c 2c on end end end # I2C #3 Touchscreen device pci 16.0 on end # Management Engine Interface 1 device pci 19.0 on chip drivers/i2c/generic register "hid" = ""10EC5682"" register "name" = ""RT58"" register "desc" = ""Realtek RT5682"" register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)" register "property_count" = "1" # Set the jd_src to RT5668_JD1 for jack detection register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" register "property_list[0].name" = ""realtek,jd-src"" register "property_list[0].integer" = "1" device i2c 1a on end end end #I2C #4 device pci 1a.0 on end # eMMC device pci 1d.2 on # PCI Express Port 11 (X2 NVMe) register "PcieRpSlotImplemented[10]" = "1" end device pci 1e.3 off end # GSPI #1 end # VR Settings Configuration for 4 Domains #+----------------+-------+-------+-------+-------+ #| Domain/Setting | SA | IA | GTUS | GTS | #+----------------+-------+-------+-------+-------+ #| Psi1Threshold | 20A | 20A | 20A | 20A | #| Psi2Threshold | 5A | 5A | 5A | 5A | #| Psi3Threshold | 1A | 1A | 1A | 1A | #| Psi3Enable | 1 | 1 | 1 | 1 | #| Psi4Enable | 1 | 1 | 1 | 1 | #| ImonSlope | 0 | 0 | 0 | 0 | #| ImonOffset | 0 | 0 | 0 | 0 | #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | #| AcLoadline | 10.04 | 1.81 | 3.19 | 3.19 | #| DcLoadline | 10.04 | 1.81 | 3.19 | 3.19 | #+----------------+-------+-------+-------+-------+ #Note: IccMax settings are moved to SoC code register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(5), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .icc_max = 0, .voltage_limit = 1520, .ac_loadline = 1004, .dc_loadline = 1004, }" register "domain_vr_config[VR_IA_CORE]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(5), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .icc_max = 0, .voltage_limit = 1520, .ac_loadline = 181, .dc_loadline = 181, }" register "domain_vr_config[VR_GT_UNSLICED]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(5), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .icc_max = 0, .voltage_limit = 1520, .ac_loadline = 319, .dc_loadline = 319, }" register "domain_vr_config[VR_GT_SLICED]" = "{ .vr_config_enable = 1, .psi1threshold = VR_CFG_AMP(20), .psi2threshold = VR_CFG_AMP(5), .psi3threshold = VR_CFG_AMP(1), .psi3enable = 1, .psi4enable = 1, .imon_slope = 0x0, .imon_offset = 0x0, .icc_max = 0, .voltage_limit = 1520, .ac_loadline = 319, .dc_loadline = 319, }" end