fw_config
field AUDIO_CODEC_SOURCE 41 43
option AUDIO_CODEC_UNPROVISIONED 0
option AUDIO_CODEC_ALC5682 1
option AUDIO_CODEC_CS42l42 2
option AUDIO_CODEC_ALC5682I_VS 3
end
end
chip soc/intel/jasperlake
# Disable PCIe Clock Source 4 (index 3)
register "PcieClkSrcUsage[3]" = "0xff"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI0 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| | before memory is up |
#| I2C0 | Trackpad |
#| I2C1 | Digitizer |
#| I2C2 | Touchscreen |
#| I2C3 | Camera |
#| I2C4 | Audio |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.gspi[0] = {
.speed_mhz = 1,
.early_init = 1,
},
.i2c[0] = {
.speed = I2C_SPEED_FAST,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 180,
.scl_hcnt = 90,
.sda_hold = 40,
}
},
.i2c[1] = {
.speed = I2C_SPEED_FAST,
},
.i2c[2] = {
.speed = I2C_SPEED_FAST,
},
.i2c[3] = {
.speed = I2C_SPEED_FAST,
},
.i2c[4] = {
.speed = I2C_SPEED_FAST,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 185,
.scl_hcnt = 95,
.sda_hold = 40,
}
},
}"
# USB Port Configuration
register "usb2_ports[2]" = "{
.enable = 1,
.ocpin = OC_SKIP,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_28P15MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # Type-A
register "usb2_ports[3]" = "{
.enable = 1,
.ocpin = OC_SKIP,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_16P9MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # WWAN
register "usb2_ports[5]" = "{
.enable = 1,
.ocpin = OC_SKIP,
.tx_bias = USB2_BIAS_0MV,
.tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON,
.pre_emp_bias = USB2_BIAS_28P15MV,
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP,
}" # Camera
register "tcc_offset" = "10" # TCC of 95C
register "xhci_lfps_sampling_offtime_ms" = "0"
device domain 0 on
device pci 04.0 on
chip drivers/intel/dptf
## Passive Policy
register "policies.passive" = "{
[0] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 52, 5000),
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 52, 5000),
[2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 50, 5000),}"
## Critical Policy
register "policies.critical" = "{
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 90, SHUTDOWN),
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 90, SHUTDOWN),
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 90, SHUTDOWN),}"
register "controls.power_limits.pl1" = "{
.min_power = 3500,
.max_power = 7000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 28 * MSECS_PER_SEC,
.granularity = 250,}"
register "controls.power_limits.pl2" = "{
.min_power = 20000,
.max_power = 20000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000,}"
## Charger Performance Control (Control, mA)
register "controls.charger_perf" = "{
[0] = { 255, 3000 },
[1] = { 32, 2000 },
[2] = { 24, 1500 },
[3] = { 16, 1000 },
[4] = { 8, 500 }
}"
device generic 0 on end
end
end # SA Thermal device
device pci 14.0 on
chip drivers/usb/acpi
device usb 0.0 on
chip drivers/usb/acpi
register "desc" = ""UFCamera""
register "type" = "UPC_TYPE_INTERNAL"
register "has_power_resource" = "1"
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D15)"
register "enable_delay_ms" = "20"
device usb 2.5 on end
end
chip drivers/usb/acpi
register "desc" = ""LTE""
register "type" = "UPC_TYPE_INTERNAL"
register "has_power_resource" = "1"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H17)"
register "reset_off_delay_ms" = "20"
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)"
register "enable_delay_ms" = "20"
device usb 3.3 on end
end
end
end
end # USB xHCI
device pci 15.0 on
chip drivers/i2c/hid
register "generic.hid" = ""SYNA0A00""
register "generic.desc" = ""SYNA Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)"
register "generic.wake" = "GPE0_DW0_03"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 2c on end
end
chip drivers/i2c/hid
register "generic.hid" = ""GXTP7288""
register "generic.desc" = ""GXTP Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)"
register "generic.wake" = "GPE0_DW0_03"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 14 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""SPPT2600""
register "generic.desc" = ""SPPT Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)"
register "generic.wake" = "GPE0_DW0_03"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 2a on end
end
chip drivers/i2c/hid
register "generic.hid" = ""PIXA2635""
register "generic.desc" = ""PIXA Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)"
register "generic.wake" = "GPE0_DW0_03"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 2d on end
end
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)"
register "wake" = "GPE0_DW0_03"
register "detect" = "1"
device i2c 15 on end
end
end #I2C 0
device pci 19.0 on
chip drivers/i2c/generic
register "hid" = ""10EC5682""
register "name" = ""RT58""
register "desc" = ""Realtek RT5682""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)"
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682
probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED
end
end
chip drivers/i2c/generic
register "hid" = ""RTL5682""
register "name" = ""RT58""
register "desc" = ""Realtek RT5682""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)"
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS
end
end
end #I2C 4
device pci 1c.7 off end # PCI Express Root Port 8
device pci 1f.3 on
chip drivers/generic/alc1015
register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)"
device generic 0 on end
end
end # Intel HDA
end
end