fw_config
field AUDIO_CODEC_SOURCE 41 43
option AUDIO_CODEC_UNPROVISIONED 0
option AUDIO_CODEC_ALC5682 1
option AUDIO_CODEC_ALC5682I_VS 2
end
end
chip soc/intel/jasperlake
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI0 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| | before memory is up |
#| I2C0 | Trackpad |
#| I2C1 | |
#| I2C2 | Touchscreen |
#| I2C3 | |
#| I2C4 | Audio |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.gspi[0] = {
.speed_mhz = 1,
.early_init = 1,
},
.i2c[0] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 247,
.fall_time_ns = 11,
},
.i2c[2] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 175,
.fall_time_ns = 20,
},
.i2c[4] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 99,
.fall_time_ns = 7,
},
}"
# USB Port Configuration
register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Not Used
register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Not Used
register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # UF Camera
register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Not Used
register "SerialIoI2cMode" = "{
[PchSerialIoIndexI2C0] = PchSerialIoPci,
[PchSerialIoIndexI2C1] = PchSerialIoDisabled,
[PchSerialIoIndexI2C2] = PchSerialIoPci,
[PchSerialIoIndexI2C3] = PchSerialIoDisabled,
[PchSerialIoIndexI2C4] = PchSerialIoPci,
[PchSerialIoIndexI2C5] = PchSerialIoDisabled,
}"
register "power_limits_config" = "{
.tdp_pl1_override = 6,
.tdp_pl2_override = 20,
}"
register "tcc_offset" = "10" # TCC of 95C
# Enable Acoustic noise mitigation and set slew rate to 1/8
# Rest of the parameters are 0 by default.
register "AcousticNoiseMitigation" = "1"
register "SlowSlewRate" = "SlewRateFastBy8"
register "FastPkgCRampDisable" = "1"
device domain 0 on
device pci 04.0 on
chip drivers/intel/dptf
## Passive Policy
register "policies.passive" = "{
[0] = DPTF_PASSIVE(CPU, CPU, 60, 50000),
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 50, 50000),
[2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 50, 50000),}"
## Critical Policy
register "policies.critical" = "{
[0] = DPTF_CRITICAL(CPU, 110, SHUTDOWN),
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 88, SHUTDOWN),
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 88, SHUTDOWN),}"
register "controls.power_limits.pl1" = "{
.min_power = 4300,
.max_power = 6000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 28 * MSECS_PER_SEC,
.granularity = 250,}"
register "controls.power_limits.pl2" = "{
.min_power = 20000,
.max_power = 20000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000,}"
device generic 0 on end
end
end # SA Thermal device
device pci 14.0 on
chip drivers/usb/acpi
device usb 0.0 on
chip drivers/usb/acpi
register "desc" = ""UFCamera""
register "type" = "UPC_TYPE_INTERNAL"
device usb 2.5 on end
end
end
end
end # USB xHCI
device pci 15.0 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)"
register "wake" = "GPE0_DW0_03"
register "probed" = "1"
device i2c 15 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""PNP0C50""
register "generic.desc" = ""Synaptics Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)"
register "generic.wake" = "GPE0_DW0_03"
register "generic.probed" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 0x2c on end
end
end # I2C 0
device pci 15.1 off end # I2C 1
device pci 15.2 on
chip drivers/i2c/hid
register "generic.hid" = ""GTCH7503""
register "generic.desc" = ""G2 Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)"
register "generic.reset_delay_ms" = "120"
register "generic.reset_off_delay_ms" = "3"
register "generic.enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)"
register "generic.enable_delay_ms" = "12"
register "generic.has_power_resource" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 0x40 on end
end
chip drivers/i2c/generic
register "hid" = ""ELAN0001""
register "desc" = ""ELAN Touchscreen""
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)"
register "probed" = "1"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)"
register "reset_delay_ms" = "20"
register "reset_off_delay_ms" = "2"
register "stop_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)"
register "stop_delay_ms" = "280"
register "stop_off_delay_ms" = "2"
register "enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)"
register "enable_delay_ms" = "1"
register "has_power_resource" = "1"
device i2c 10 on end
end
end # I2C 2
device pci 15.3 off end # I2C 3
device pci 19.0 on
chip drivers/i2c/generic
register "hid" = ""10EC5682""
register "name" = ""RT58""
register "desc" = ""Realtek RT5682""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)"
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED
probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682
end
end
chip drivers/i2c/generic
register "hid" = ""RTL5682""
register "name" = ""RT58""
register "desc" = ""Realtek RT5682""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)"
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS
end
end
end # I2C 4
device pci 1f.3 on
chip drivers/generic/alc1015
register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)"
device generic 0 on end
end
end # Intel HDA
end
end