fw_config
field DB_USB 0 1
option DB_USB_ABSENT 0
option DB_USB3_NO_A 1
option DB_USB3_1C_1A 2
end
field DB_SD 2 3
option DB_SD_ABSENT 0
option DB_SD_OZ711LV2LN 1
end
field KB_BL 4
option KB_BL_ABSENT 0
option KB_BL_PRESENT 1
end
field AUDIO 5 7
option AUDIO_UNKNOWN 0
option AUDIO_MAX98357_ALC5682I_I2S 1
option AUDIO_MAX98357_ALC5682I_VS_I2S 2
end
field KB_LAYOUT 8 9
option KB_LAYOUT_DEFAULT 0
end
field WIFI_SAR_ID 10 11
option WIFI_SAR_ID_0 0
option WIFI_SAR_ID_1 1
option WIFI_SAR_ID_2 2
option WIFI_SAR_ID_3 3
end
field BOOT_NVME_MASK 12
option BOOT_NVME_DISABLED 0
option BOOT_NVME_ENABLED 1
end
field BOOT_EMMC_MASK 13
option BOOT_EMMC_DISABLED 0
option BOOT_EMMC_ENABLED 1
end
field THERMAL 16
option THERMAL_FAN_TABLE_0 0
option THERMAL_FAN_TABLE_1 1
end
field HPS 17
option HPS_ABSENT 0
option HPS_PRESENT 1
end
end
chip soc/intel/alderlake
register "domain_vr_config[VR_DOMAIN_IA]" = "{
.enable_fast_vmode = 1,
}"
# As per Intel Advisory doc#723158, the change is required to prevent possible
# display flickering issue.
register "usb2_phy_sus_pg_disable" = "1"
# Acoustic settings
register "acoustic_noise_mitigation" = "1"
register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8"
register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8"
register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1"
register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1"
register "PreWake" = "100"
register "ext_fivr_settings" = "{
.configure_ext_fivr = 1,
.v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX,
.vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
.v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL |
FIVR_VOLTAGE_MIN_ACTIVE |
FIVR_VOLTAGE_MIN_RETENTION,
.vnn_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL |
FIVR_VOLTAGE_MIN_ACTIVE |
FIVR_VOLTAGE_MIN_RETENTION,
.v1p05_icc_max_ma = 500,
.vnn_sx_voltage_mv = 1250,
}"
register "tcss_aux_ori" = "1"
register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
register "sagv" = "SaGv_Enabled"
register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable Port 1
register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC2)" # DB USB2_C1
register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable M.2 WWAN
register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # DB Type-A Port A1
register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC3)" # USB3/2 Type A port A1
register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Disable M.2 WWAN
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI1 | Fingerprint MCU |
#| I2C0 | Audio |
#| I2C1 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| I2C2 | HPS |
#| I2C3 | Touchscreen |
#| I2C5 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.i2c[0] = {
.speed = I2C_SPEED_FAST,
},
.i2c[1] = {
.early_init = 1,
.speed = I2C_SPEED_FAST,
.rise_time_ns = 600,
.fall_time_ns = 400,
.data_hold_time_ns = 50,
},
.i2c[2] = {
.speed = I2C_SPEED_FAST,
},
.i2c[3] = {
.early_init = 1,
.speed = I2C_SPEED_FAST,
},
.i2c[5] = {
.rise_time_ns = 650,
.fall_time_ns = 400,
.data_hold_time_ns = 500,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 160,
.scl_hcnt = 70,
.sda_hold = 40,
}
},
}"
# I2C Port Config
register "serial_io_i2c_mode" = "{
[PchSerialIoIndexI2C0] = PchSerialIoPci,
[PchSerialIoIndexI2C1] = PchSerialIoPci,
[PchSerialIoIndexI2C2] = PchSerialIoPci,
[PchSerialIoIndexI2C3] = PchSerialIoPci,
[PchSerialIoIndexI2C4] = PchSerialIoDisabled,
[PchSerialIoIndexI2C5] = PchSerialIoPci,
}"
device domain 0 on
device ref dtt on
chip drivers/intel/dptf
## sensor information
register "options.tsr[0].desc" = ""DRAM_SOC""
register "options.tsr[1].desc" = ""Ambient""
register "options.tsr[2].desc" = ""Charger""
register "options.tsr[3].desc" = ""WWAN""
# TODO: below values are initial reference values only
## Active Policy
register "policies.active" = "{
[0] = {
.target = DPTF_CPU,
.thresholds = {
TEMP_PCT(85, 90),
TEMP_PCT(80, 74),
TEMP_PCT(75, 74),
TEMP_PCT(70, 74),
TEMP_PCT(65, 74),
}
},
[1] = {
.target = DPTF_TEMP_SENSOR_1,
.thresholds = {
TEMP_PCT(50, 70),
TEMP_PCT(47, 58),
TEMP_PCT(45, 47),
TEMP_PCT(42, 45),
TEMP_PCT(39, 39),
}
},
[2] = {
.target = DPTF_TEMP_SENSOR_2,
.thresholds = {
TEMP_PCT(50, 70),
TEMP_PCT(47, 58),
TEMP_PCT(45, 47),
TEMP_PCT(42, 45),
TEMP_PCT(39, 39),
}
},
[3] = {
.target = DPTF_TEMP_SENSOR_3,
.thresholds = {
TEMP_PCT(50, 70),
TEMP_PCT(47, 58),
TEMP_PCT(45, 47),
TEMP_PCT(42, 45),
TEMP_PCT(39, 39),
}
}
}"
## Passive Policy
register "policies.passive" = "{
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 90, 6000),
[2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 90, 6000),
[3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 90, 6000),
[4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 90, 6000),
}"
## Critical Policy
register "policies.critical" = "{
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 100, SHUTDOWN),
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 100, SHUTDOWN),
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 100, SHUTDOWN),
[4] = DPTF_CRITICAL(TEMP_SENSOR_3, 100, SHUTDOWN),
}"
register "controls.power_limits" = "{
.pl1 = {
.min_power = 3000,
.max_power = 15000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 200,
},
.pl2 = {
.min_power = 55000,
.max_power = 55000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000,
}
}"
## Charger Performance Control (Control, mA)
register "controls.charger_perf" = "{
[0] = { 255, 1700 },
[1] = { 24, 1500 },
[2] = { 16, 1000 },
[3] = { 8, 500 }
}"
## Fan Performance Control (Percent, Speed, Noise, Power)
register "controls.fan_perf" = "{
[0] = { 100, 6000, 220, 2200, },
[1] = { 92, 5500, 180, 1800, },
[2] = { 85, 5000, 145, 1450, },
[3] = { 70, 4400, 115, 1150, },
[4] = { 56, 3900, 90, 900, },
[5] = { 45, 3300, 55, 550, },
[6] = { 38, 3000, 30, 300, },
[7] = { 33, 2900, 15, 150, },
[8] = { 10, 800, 10, 100, },
[9] = { 0, 0, 0, 50, }
}"
## Fan options
register "options.fan.fine_grained_control" = "1"
register "options.fan.step_size" = "2"
device generic 0 on
probe THERMAL THERMAL_FAN_TABLE_0
end
end
chip drivers/intel/dptf
## sensor information
register "options.tsr[0].desc" = ""DRAM_SOC""
register "options.tsr[1].desc" = ""Ambient""
register "options.tsr[2].desc" = ""Charger""
register "options.tsr[3].desc" = ""WWAN""
## Active Policy
register "policies.active" = "{
[0] = {
.target = DPTF_CPU,
.thresholds = {
TEMP_PCT(60, 68),
TEMP_PCT(56, 50),
TEMP_PCT(52, 50),
TEMP_PCT(46, 40),
TEMP_PCT(42, 40),
}
},
[1] = {
.target = DPTF_TEMP_SENSOR_1,
.thresholds = {
TEMP_PCT(60, 68),
TEMP_PCT(56, 50),
TEMP_PCT(52, 50),
TEMP_PCT(46, 40),
TEMP_PCT(42, 40),
}
},
[2] = {
.target = DPTF_TEMP_SENSOR_2,
.thresholds = {
TEMP_PCT(60, 68),
TEMP_PCT(56, 50),
TEMP_PCT(52, 50),
TEMP_PCT(46, 40),
TEMP_PCT(42, 40),
}
},
[3] = {
.target = DPTF_TEMP_SENSOR_3,
.thresholds = {
TEMP_PCT(60, 68),
TEMP_PCT(56, 50),
TEMP_PCT(52, 50),
TEMP_PCT(46, 40),
TEMP_PCT(42, 40),
}
}
}"
## Passive Policy
register "policies.passive" = "{
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 90, 6000),
[2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 90, 6000),
[3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 90, 6000),
[4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 90, 6000),
}"
## Critical Policy
register "policies.critical" = "{
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 100, SHUTDOWN),
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 100, SHUTDOWN),
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 100, SHUTDOWN),
[4] = DPTF_CRITICAL(TEMP_SENSOR_3, 100, SHUTDOWN),
}"
register "controls.power_limits" = "{
.pl1 = {
.min_power = 3000,
.max_power = 15000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 200,
},
.pl2 = {
.min_power = 55000,
.max_power = 55000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000,
}
}"
## Charger Performance Control (Control, mA)
register "controls.charger_perf" = "{
[0] = { 255, 1700 },
[1] = { 24, 1500 },
[2] = { 16, 1000 },
[3] = { 8, 500 }
}"
## Fan Performance Control (Percent, Speed, Noise, Power)
register "controls.fan_perf" = "{
[0] = { 100, 6000, 220, 2200, },
[1] = { 92, 5500, 180, 1800, },
[2] = { 78, 4500, 145, 1450, },
[3] = { 68, 3900, 115, 1150, },
[4] = { 60, 3600, 90, 900, },
[5] = { 50, 3200, 55, 550, },
[6] = { 40, 2800, 30, 300, },
[7] = { 33, 2500, 15, 150, },
[8] = { 12, 800, 10, 100, },
[9] = { 0, 0, 0, 50, }
}"
## Fan options
register "options.fan.fine_grained_control" = "1"
register "options.fan.step_size" = "2"
device generic 1 on
probe THERMAL THERMAL_FAN_TABLE_1
end
end
end
device ref pcie4_0 on
# Enable CPU PCIE RP 1 using CLK 0
register "cpu_pcie_rp[CPU_RP(1)]" = "{
.clk_req = 0,
.clk_src = 0,
.flags = PCIE_RP_LTR | PCIE_RP_AER,
}"
probe BOOT_NVME_MASK BOOT_NVME_ENABLED
end
device ref tbt_pcie_rp0 off end
device ref tbt_pcie_rp1 off end
device ref tbt_pcie_rp2 off end
device ref i2c0 on
chip drivers/i2c/generic
register "hid" = ""10EC5682""
register "name" = ""RT58""
register "desc" = ""Headset Codec""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO AUDIO_MAX98357_ALC5682I_I2S
end
end
chip drivers/i2c/generic
register "hid" = ""RTL5682""
register "name" = ""RT58""
register "desc" = ""Headset Codec""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO AUDIO_MAX98357_ALC5682I_VS_I2S
end
end
end
device ref i2c1 on
chip drivers/i2c/tpm
register "hid" = ""GOOG0005""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
device i2c 50 on end
end
end
device ref i2c2 on
chip drivers/i2c/generic
register "hid" = ""GOOG0020""
register "desc" = ""ChromeOS HPS""
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E7)" # EN_HPS_PWR
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E3_IRQ)" # HPS_INT_ODL
# HPS uses I2C addresses 0x30 and 0x51.
# The address we provide here is not significant because
# neither coreboot nor Linux have a driver for HPS,
# it's only used from userspace.
device i2c 30 on
probe HPS HPS_PRESENT
end
end
end
device ref i2c3 on
chip drivers/i2c/hid
register "generic.hid" = ""GDIX0000""
register "generic.desc" = ""Goodix Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
# Parameter T5 >= 180ms
register "generic.reset_delay_ms" = "180"
# Parameter T2 >= 1ms
register "generic.reset_off_delay_ms" = "3"
register "generic.enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
# Parameter T1 >= 20ms
register "generic.enable_delay_ms" = "20"
register "generic.stop_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E3)"
# Parameter T4 >= 1ms
register "generic.stop_off_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 5d on end
end
chip drivers/i2c/generic
register "hid" = ""ELAN0001""
register "desc" = ""ELAN Touchscreen""
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "probed" = "1"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
register "reset_delay_ms" = "20"
register "enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
register "enable_delay_ms" = "1"
register "has_power_resource" = "1"
device i2c 10 on end
end
end
device ref i2c5 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
register "wake" = "GPE0_DW2_14"
register "detect" = "1"
device i2c 15 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""SYNA0000""
register "generic.cid" = ""ACPI0C50""
register "generic.desc" = ""Synaptics Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
register "generic.wake" = "GPE0_DW2_14"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 2c on end
end
end
device ref hda on
chip drivers/generic/max98357a
register "hid" = ""MX98357A""
register "sdmode_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
register "sdmode_delay" = "5"
device generic 0 on
probe AUDIO AUDIO_MAX98357_ALC5682I_I2S
probe AUDIO AUDIO_MAX98357_ALC5682I_VS_I2S
end
end
chip drivers/sof
register "spkr_tplg" = "max98357a"
register "jack_tplg" = "rt5682"
register "mic_tplg" = "_2ch_pdm0"
device generic 0 on end
end
end
device ref pcie_rp5 on
chip soc/intel/common/block/pcie/rtd3
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)"
register "srcclk_pin" = "2"
device generic 0 on end
end
register "pch_pcie_rp[PCH_RP(5)]" = "{
.clk_src = 2,
.clk_req = 2,
.flags = PCIE_RP_LTR | PCIE_RP_AER,
}"
end
device ref pcie_rp6 off end
device ref pcie_rp8 on
chip soc/intel/common/block/pcie/rtd3
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)"
register "srcclk_pin" = "3"
device generic 0 on
probe DB_SD DB_SD_OZ711LV2LN
end
end
end
device ref pcie_rp9 on
# Enable PCIE 9 using clk 0 for eMMC
register "pch_pcie_rp[PCH_RP(9)]" = "{
.clk_src = 0,
.clk_req = 0,
.flags = PCIE_RP_LTR | PCIE_RP_AER,
.pcie_rp_aspm = ASPM_L1,
}"
probe BOOT_EMMC_MASK BOOT_EMMC_ENABLED
end
device ref gspi1 on
chip drivers/spi/acpi
register "name" = ""CRFP""
register "hid" = "ACPI_DT_NAMESPACE_HID"
register "uid" = "1"
register "compat_string" = ""google,cros-ec-spi""
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)"
register "wake" = "GPE0_DW2_15"
register "has_power_resource" = "1"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)"
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)"
register "enable_delay_ms" = "3"
device spi 0 on end
end # FPMCU
end
device ref pch_espi on
chip ec/google/chromeec
use conn0 as mux_conn[0]
use conn1 as mux_conn[1]
device pnp 0c09.0 on end
end
end
device ref pmc hidden
chip drivers/intel/pmc_mux
device generic 0 on
chip drivers/intel/pmc_mux/conn
use usb2_port1 as usb2_port
use tcss_usb3_port1 as usb3_port
device generic 0 alias conn0 on end
end
chip drivers/intel/pmc_mux/conn
use usb2_port3 as usb2_port
use tcss_usb3_port3 as usb3_port
device generic 2 alias conn1 on end
end
end
end
end
device ref tcss_xhci on
chip drivers/usb/acpi
device ref tcss_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
device ref tcss_usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
register "usb_lpm_incapable" = "true"
device ref tcss_usb3_port3 on
probe DB_USB DB_USB3_NO_A
probe DB_USB DB_USB3_1C_1A
end
end
end
end
end
device ref xhci on
chip drivers/usb/acpi
device ref xhci_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
device ref usb2_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
device ref usb2_port3 on
probe DB_USB DB_USB3_NO_A
probe DB_USB DB_USB3_1C_1A
end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Camera""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port6 on
end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port (DB)""
register "type" = "UPC_TYPE_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(3, 1))"
register "group" = "ACPI_PLD_GROUP(3, 1)"
device ref usb2_port7 on
probe DB_USB DB_USB3_1C_1A
end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port (MLB)""
register "type" = "UPC_TYPE_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))"
device ref usb2_port9 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
device ref usb2_port10 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port (MLB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))"
device ref usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port (DB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(3, 1))"
device ref usb3_port3 on
probe DB_USB DB_USB3_1C_1A
end
end
end
end
end
end
end