fw_config field DB_USB 0 3 option USB_ABSENT 0 option USB3_PS8815 1 end field DB_SD 4 5 option SD_ABSENT 0 option SD_GL9755S 1 end field KB_BL 7 7 option KB_BL_ABSENT 0 option KB_BL_PRESENT 1 end field AUDIO 8 10 option AUDIO_UNKNOWN 0 option MAX98357_ALC5682I_I2S 1 option MAX98373_ALC5682_SNDW 2 option MAX98373_NAU88L25B_I2S 3 option ALC1019_NAU88L25B_I2S 4 option MAX98360_ALC5682I_I2S 5 option NAU8318_NAU88L25B_I2S 6 end field DB_LTE 11 12 option LTE_ABSENT 0 option LTE_USB 1 option LTE_PCIE 2 end field UFC 13 14 option UFC_USB 0 option UFC_MIPI_IMX208 1 end field WFC 15 16 option WFC_ABSENT 0 option WFC_MIPI_OVTI8856 1 option WFC_MIPI_KBAE350 2 end field HPS 17 17 option HPS_ABSENT 0 option HPS_PRESENT 1 end field THERMAL 18 18 option THERMAL_28W 0 option THERMAL_15W 1 end end chip soc/intel/alderlake register "domain_vr_config[VR_DOMAIN_IA]" = "{ .enable_fast_vmode = 1, }" register "sagv" = "SaGv_Enabled" # As per Intel Advisory doc#723158, the change is required to prevent possible # display flickering issue. register "disable_dynamic_tccold_handshake" = "true" register "platform_pmax" = "145" register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MLB Port register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" # FIVR configurations for brya are disabled since the board doesn't have V1p05 and Vnn # bypass rails implemented. register "ext_fivr_settings" = "{ .configure_ext_fivr = 1, }" # Intel Common SoC Config #+-------------------+---------------------------+ #| Field | Value | #+-------------------+---------------------------+ #| GSPI1 | Fingerprint MCU | #| I2C0 | Audio | #| I2C1 | cr50 TPM. Early init is | #| | required to set up a BAR | #| | for TPM communication | #| I2C2 | SAR | #| I2C3 | TouchScreen | #| I2C5 | Trackpad | #+-------------------+---------------------------+ register "common_soc_config" = "{ .i2c[0] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 650, .fall_time_ns = 400, .data_hold_time_ns = 50, }, .i2c[1] = { .early_init = 1, .speed = I2C_SPEED_FAST, .rise_time_ns = 600, .fall_time_ns = 400, .data_hold_time_ns = 50, }, .i2c[2] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 900, .fall_time_ns = 400, .data_hold_time_ns = 50, }, .i2c[3] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 600, .fall_time_ns = 400, .data_hold_time_ns = 50, }, .i2c[5] = { .speed = I2C_SPEED_FAST, .rise_time_ns = 650, .fall_time_ns = 400, .data_hold_time_ns = 50, }, }" device domain 0 on device ref igpu on chip drivers/gfx/generic register "device_count" = "6" # DDIA for eDP register "device[0].name" = ""LCD0"" # Internal panel on the first port of the graphics chip register "device[0].type" = "panel" # DDIB for HDMI # If HDMI is not enumerated in the kernel, then no GFX device should be added for DDIB register "device[1].name" = ""DD01"" # TCP0 (DP-1) for port C0 register "device[2].name" = ""DD02"" register "device[2].use_pld" = "true" register "device[2].pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))" # TCP1 (DP-2) for port C1 register "device[3].name" = ""DD03"" register "device[3].use_pld" = "true" register "device[3].pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" # TCP2 (DP-3) for port C2 register "device[4].name" = ""DD04"" register "device[4].use_pld" = "true" register "device[4].pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" # TCP3 (DP-4) is unused for any ports but still enumerated in the kernel, so GFX device is added for TCP3 register "device[5].name" = ""DD05"" device generic 0 on end end end # Integrated Graphics Device device ref dtt on chip drivers/intel/dptf ## sensor information register "options.tsr[0].desc" = ""DRAM_SOC"" register "options.tsr[1].desc" = ""Ambient"" register "options.tsr[2].desc" = ""Charger"" register "options.tsr[3].desc" = ""WWAN"" # TODO: below values are initial reference values only ## Active Policy register "policies.active" = "{ [0] = { .target = DPTF_TEMP_SENSOR_0, .thresholds = { TEMP_PCT(75, 95), TEMP_PCT(70, 90), TEMP_PCT(65, 80), TEMP_PCT(60, 70), TEMP_PCT(55, 60), TEMP_PCT(50, 50), TEMP_PCT(45, 40), TEMP_PCT(40, 30), } }, [1] = { .target = DPTF_TEMP_SENSOR_1, .thresholds = { TEMP_PCT(75, 95), TEMP_PCT(70, 90), TEMP_PCT(65, 80), TEMP_PCT(60, 70), TEMP_PCT(55, 60), TEMP_PCT(50, 50), TEMP_PCT(45, 40), TEMP_PCT(40, 30), } }, [2] = { .target = DPTF_TEMP_SENSOR_2, .thresholds = { TEMP_PCT(82, 97), TEMP_PCT(78, 93), TEMP_PCT(72, 86), TEMP_PCT(66, 60), TEMP_PCT(60, 40), } }, [3] = { .target = DPTF_TEMP_SENSOR_3, .thresholds = { TEMP_PCT(75, 95), TEMP_PCT(70, 90), TEMP_PCT(65, 80), TEMP_PCT(60, 70), TEMP_PCT(55, 60), TEMP_PCT(50, 50), TEMP_PCT(45, 40), TEMP_PCT(40, 30), } } }" ## Passive Policy register "policies.passive" = "{ [0] = DPTF_PASSIVE(CPU, CPU, 97, 5000), [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 85, 5000), [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 85, 5000), [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 80, 5000), [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 85, 5000), }" ## Critical Policy register "policies.critical" = "{ [0] = DPTF_CRITICAL(CPU, 115, SHUTDOWN), [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 90, SHUTDOWN), [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 90, SHUTDOWN), [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 90, SHUTDOWN), [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 90, SHUTDOWN), }" register "controls.power_limits" = "{ .pl1 = { .min_power = 28000, .max_power = 28000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 200, }, .pl2 = { .min_power = 64000, .max_power = 64000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 1000, } }" ## Charger Performance Control (Control, mA) register "controls.charger_perf" = "{ [0] = { 255, 1700 }, [1] = { 24, 1500 }, [2] = { 16, 1000 }, [3] = { 8, 500 } }" ## Fan Performance Control (Percent, Speed, Noise, Power) register "controls.fan_perf" = "{ [0] = { 90, 6700, 220, 2200, }, [1] = { 80, 5800, 180, 1800, }, [2] = { 70, 5000, 145, 1450, }, [3] = { 60, 4900, 115, 1150, }, [4] = { 50, 3838, 90, 900, }, [5] = { 40, 2904, 55, 550, }, [6] = { 30, 2337, 30, 300, }, [7] = { 20, 1608, 15, 150, }, [8] = { 10, 800, 10, 100, }, [9] = { 0, 0, 0, 50, } }" ## Fan options register "options.fan.fine_grained_control" = "1" register "options.fan.step_size" = "2" device generic 0 on probe THERMAL THERMAL_28W end end chip drivers/intel/dptf ## sensor information register "options.tsr[0].desc" = ""DRAM_SOC"" register "options.tsr[1].desc" = ""Ambient"" register "options.tsr[2].desc" = ""Charger"" register "options.tsr[3].desc" = ""WWAN"" # TODO: below values are initial reference values only ## Active Policy register "policies.active" = "{ [0] = { .target = DPTF_TEMP_SENSOR_0, .thresholds = { TEMP_PCT(75, 97), TEMP_PCT(70, 93), TEMP_PCT(60, 86), TEMP_PCT(52, 80), TEMP_PCT(47, 64), TEMP_PCT(43, 52), TEMP_PCT(40, 40), } }, [1] = { .target = DPTF_TEMP_SENSOR_1, .thresholds = { TEMP_PCT(75, 97), TEMP_PCT(70, 93), TEMP_PCT(60, 86), TEMP_PCT(52, 80), TEMP_PCT(47, 64), TEMP_PCT(43, 52), TEMP_PCT(40, 40), } }, [2] = { .target = DPTF_TEMP_SENSOR_2, .thresholds = { TEMP_PCT(82, 97), TEMP_PCT(78, 93), TEMP_PCT(72, 86), TEMP_PCT(60, 80), } }, [3] = { .target = DPTF_TEMP_SENSOR_3, .thresholds = { TEMP_PCT(75, 97), TEMP_PCT(70, 93), TEMP_PCT(60, 86), TEMP_PCT(52, 80), TEMP_PCT(47, 64), TEMP_PCT(43, 52), TEMP_PCT(40, 40), } } }" ## Passive Policy register "policies.passive" = "{ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 80, 5000), [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 80, 5000), [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 5000), [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 80, 5000), }" ## Critical Policy register "policies.critical" = "{ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN), }" register "controls.power_limits" = "{ .pl1 = { .min_power = 15000, .max_power = 15000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 200, }, .pl2 = { .min_power = 55000, .max_power = 55000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 1000, } }" ## Charger Performance Control (Control, mA) register "controls.charger_perf" = "{ [0] = { 255, 1700 }, [1] = { 24, 1500 }, [2] = { 16, 1000 }, [3] = { 8, 500 } }" ## Fan Performance Control (Percent, Speed, Noise, Power) register "controls.fan_perf" = "{ [0] = { 90, 6700, 220, 2200, }, [1] = { 80, 5800, 180, 1800, }, [2] = { 70, 5000, 145, 1450, }, [3] = { 60, 4900, 115, 1150, }, [4] = { 50, 3838, 90, 900, }, [5] = { 40, 2904, 55, 550, }, [6] = { 30, 2337, 30, 300, }, [7] = { 20, 1608, 15, 150, }, [8] = { 10, 800, 10, 100, }, [9] = { 0, 0, 0, 50, } }" ## Fan options register "options.fan.fine_grained_control" = "1" register "options.fan.step_size" = "2" device generic 1 on probe THERMAL THERMAL_15W end end end device ref ipu on chip drivers/intel/mipi_camera register "acpi_uid" = "0x50000" register "acpi_name" = ""IPU0"" register "device_type" = "INTEL_ACPI_CAMERA_CIO2" register "cio2_num_ports" = "1" register "cio2_lanes_used" = "{4}" # 4 CSI Camera lanes are used register "cio2_lane_endpoint[0]" = ""^I2C0.CAM0"" register "cio2_prt[0]" = "2" device generic 0 on # MIPI lanes are split between UFC and WFC depending on # whether the UFC is USB or MIPI hence probing UFC_USB probe UFC UFC_USB end end chip drivers/intel/mipi_camera register "acpi_uid" = "0x50000" register "acpi_name" = ""IPU0"" register "device_type" = "INTEL_ACPI_CAMERA_CIO2" register "cio2_num_ports" = "2" register "cio2_lanes_used" = "{4,2}" # 4 and 2 CSI Camera lanes are used register "cio2_lane_endpoint[0]" = ""^I2C0.CAM0"" register "cio2_lane_endpoint[1]" = ""^I2C2.CAM1"" register "cio2_prt[0]" = "2" register "cio2_prt[1]" = "1" device generic 1 on probe UFC UFC_MIPI_IMX208 end end end device ref cnvi_wifi on chip drivers/wifi/generic register "wake" = "GPE0_PME_B0" register "enable_cnvi_ddr_rfim" = "true" device generic 0 on end end end device ref pcie_rp6 on # Enable WWAN PCIE 6 using clk 5 register "pch_pcie_rp[PCH_RP(6)]" = "{ .clk_src = 5, .clk_req = 5, .flags = PCIE_RP_LTR | PCIE_RP_AER, }" chip soc/intel/common/block/pcie/rtd3 register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)" register "reset_off_delay_ms" = "20" # register "reset_delay_ms" = "1000" register "srcclk_pin" = "5" register "ext_pm_support" = "ACPI_PCIE_RP_EMIT_ALL" register "skip_on_off_support" = "true" register "use_rp_mutex" = "true" device generic 0 alias rp6_rtd3 on probe DB_LTE LTE_PCIE end end chip drivers/wwan/fm register "fcpo_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F21)" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E16)" register "perst_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)" register "wake_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A7)" register "add_acpi_dma_property" = "true" use rp6_rtd3 as rtd3dev device generic 0 on probe DB_LTE LTE_PCIE end end probe DB_LTE LTE_PCIE end device ref tcss_dma0 on chip drivers/intel/usb4/retimer register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" use tcss_usb3_port1 as dfp[0].typec_port device generic 0 on end end end device ref tcss_dma1 on chip drivers/intel/usb4/retimer register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" use tcss_usb3_port3 as dfp[0].typec_port device generic 0 on end end end device ref pcie_rp8 on chip soc/intel/common/block/pcie/rtd3 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" register "srcclk_pin" = "3" device generic 0 on end end end #PCIE8 SD card device ref i2c0 on chip drivers/i2c/generic register "hid" = ""10EC5682"" register "name" = ""RT58"" register "desc" = ""Headset Codec"" register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" # Set the jd_src to RT5668_JD1 for jack detection register "property_count" = "1" register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" register "property_list[0].name" = ""realtek,jd-src"" register "property_list[0].integer" = "1" device i2c 1a on probe AUDIO MAX98357_ALC5682I_I2S probe AUDIO MAX98360_ALC5682I_I2S end end chip drivers/i2c/nau8825 register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" register "jkdet_enable" = "1" register "jkdet_pull_enable" = "0" register "jkdet_polarity" = "1" # ActiveLow register "vref_impedance" = "2" # 125kOhm register "micbias_voltage" = "6" # 2.754 register "sar_threshold_num" = "4" register "sar_threshold[0]" = "0x0c" register "sar_threshold[1]" = "0x1c" register "sar_threshold[2]" = "0x38" register "sar_threshold[3]" = "0x60" register "sar_hysteresis" = "1" register "sar_voltage" = "0" # VDDA register "sar_compare_time" = "0" # 500ns register "sar_sampling_time" = "0" # 2us register "short_key_debounce" = "2" # 100ms register "jack_insert_debounce" = "7" # 512ms register "jack_eject_debounce" = "7" # 512ms device i2c 1a on probe AUDIO ALC1019_NAU88L25B_I2S probe AUDIO NAU8318_NAU88L25B_I2S end end chip drivers/generic/alc1015 register "hid" = ""RTL1019"" register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" device generic 1 on probe AUDIO ALC1019_NAU88L25B_I2S end end chip drivers/intel/mipi_camera register "acpi_hid" = ""OVTI8856"" register "acpi_uid" = "0" register "acpi_name" = ""CAM0"" register "chip_name" = ""Ov 8856 Camera"" register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" register "ssdb.lanes_used" = "4" register "ssdb.link_used" = "0" register "ssdb.vcm_type" = "0x0C" register "vcm_name" = ""VCM0"" register "num_freq_entries" = "2" register "link_freq[0]" = "360 * MHz" # 360 MHz register "link_freq[1]" = "180 * MHz" # 180 MHz register "remote_name" = ""IPU0"" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" register "has_power_resource" = "1" #Controls register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #power_enable_2p8 register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" #power_enable_1p2 register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" #reset #_ON register "on_seq.ops_cnt" = "5" register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" #_OFF register "off_seq.ops_cnt" = "4" register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 10 on probe WFC WFC_MIPI_OVTI8856 end end chip drivers/intel/mipi_camera register "acpi_uid" = "2" register "acpi_name" = ""VCM0"" register "chip_name" = ""DW9768 VCM"" register "device_type" = "INTEL_ACPI_CAMERA_VCM" register "vcm_compat" = ""dongwoon,dw9768"" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D0" register "has_power_resource" = "1" #Controls register "gpio_panel.gpio[0].gpio_num" = "GPP_D16" #EN_WCAM_PWR #_ON register "on_seq.ops_cnt" = "1" register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)" #_OFF register "off_seq.ops_cnt" = "1" register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 0C on probe WFC WFC_MIPI_OVTI8856 end end chip drivers/intel/mipi_camera register "acpi_uid" = "1" register "acpi_name" = ""NVM0"" register "chip_name" = ""AT24 EEPROM"" register "device_type" = "INTEL_ACPI_CAMERA_NVM" register "nvm_compat" = ""atmel,24c1024"" register "nvm_size" = "0x2800" register "nvm_pagesize" = "0x01" register "nvm_readonly" = "0x01" register "nvm_width" = "0x10" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D0" register "has_power_resource" = "1" #Controls register "gpio_panel.gpio[0].gpio_num" = "GPP_D16" #EN_WCAM_PWR #_ON register "on_seq.ops_cnt" = "1" register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)" #_OFF register "off_seq.ops_cnt" = "1" register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 58 on probe WFC WFC_MIPI_OVTI8856 end end chip drivers/intel/mipi_camera register "acpi_hid" = ""OVTI8856"" register "acpi_uid" = "0" register "acpi_name" = ""CAM0"" register "chip_name" = ""Ov 8856 Camera"" register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" register "ssdb.lanes_used" = "4" register "ssdb.link_used" = "0" register "ssdb.vcm_type" = "0x0C" register "vcm_name" = ""VCM0"" register "num_freq_entries" = "2" register "link_freq[0]" = "360 * MHz" # 360 MHz register "link_freq[1]" = "180 * MHz" # 180 MHz register "remote_name" = ""IPU0"" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" register "has_power_resource" = "1" #Controls register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #power_enable_2p8 register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" #power_enable_1p2 register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" #reset #_ON register "on_seq.ops_cnt" = "5" register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" #_OFF register "off_seq.ops_cnt" = "4" register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 36 on probe WFC WFC_MIPI_KBAE350 end end chip drivers/intel/mipi_camera register "acpi_uid" = "2" register "acpi_name" = ""VCM0"" register "chip_name" = ""DW AF DAC"" register "device_type" = "INTEL_ACPI_CAMERA_VCM" register "vcm_compat" = ""dongwoon,dw9714"" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D0" register "has_power_resource" = "1" #Controls register "gpio_panel.gpio[0].gpio_num" = "GPP_D16" #EN_WCAM_PWR #_ON register "on_seq.ops_cnt" = "1" register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)" #_OFF register "off_seq.ops_cnt" = "1" register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 0C on probe WFC WFC_MIPI_KBAE350 end end chip drivers/intel/mipi_camera register "acpi_uid" = "1" register "acpi_name" = ""NVM0"" register "chip_name" = ""GT24C08"" register "device_type" = "INTEL_ACPI_CAMERA_NVM" register "nvm_compat" = ""atmel,24c08"" register "nvm_size" = "0x2000" register "nvm_pagesize" = "0x01" register "nvm_readonly" = "0x01" register "nvm_width" = "0x10" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D0" register "has_power_resource" = "1" #Controls register "gpio_panel.gpio[0].gpio_num" = "GPP_D16" #EN_WCAM_PWR #_ON register "on_seq.ops_cnt" = "1" register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)" #_OFF register "off_seq.ops_cnt" = "1" register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 50 on probe WFC WFC_MIPI_KBAE350 end end end #I2C0 device ref i2c1 on chip drivers/i2c/tpm register "hid" = ""GOOG0005"" register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" device i2c 50 on end end end #I2C1 device ref i2c2 on chip drivers/i2c/sx9324 register "desc" = ""SAR1 Proximity Sensor"" register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" register "speed" = "I2C_SPEED_FAST" register "uid" = "1" register "reg_gnrl_ctrl0" = "0x16" register "reg_gnrl_ctrl1" = "0x21" register "reg_afe_ctrl0" = "0x00" register "reg_afe_ctrl1" = "0x10" register "reg_afe_ctrl2" = "0x00" register "reg_afe_ctrl3" = "0x00" register "reg_afe_ctrl4" = "0x07" register "reg_afe_ctrl5" = "0x00" register "reg_afe_ctrl6" = "0x00" register "reg_afe_ctrl7" = "0x07" register "reg_afe_ctrl8" = "0x12" register "reg_afe_ctrl9" = "0x0f" register "reg_prox_ctrl0" = "0x12" register "reg_prox_ctrl1" = "0x12" register "reg_prox_ctrl2" = "0x90" register "reg_prox_ctrl3" = "0x60" register "reg_prox_ctrl4" = "0x0c" register "reg_prox_ctrl5" = "0x12" register "reg_prox_ctrl6" = "0x3c" register "reg_prox_ctrl7" = "0x58" register "reg_adv_ctrl0" = "0x00" register "reg_adv_ctrl1" = "0x00" register "reg_adv_ctrl2" = "0x00" register "reg_adv_ctrl3" = "0x00" register "reg_adv_ctrl4" = "0x00" register "reg_adv_ctrl5" = "0x05" register "reg_adv_ctrl6" = "0x00" register "reg_adv_ctrl7" = "0x00" register "reg_adv_ctrl8" = "0x00" register "reg_adv_ctrl9" = "0x00" register "reg_adv_ctrl10" = "0x5c" register "reg_adv_ctrl11" = "0x52" register "reg_adv_ctrl12" = "0xb5" register "reg_adv_ctrl13" = "0x00" register "reg_adv_ctrl14" = "0x80" register "reg_adv_ctrl15" = "0x0c" register "reg_adv_ctrl16" = "0x38" register "reg_adv_ctrl17" = "0x56" register "reg_adv_ctrl18" = "0x33" register "reg_adv_ctrl19" = "0xf0" register "reg_adv_ctrl20" = "0xf0" device i2c 28 on end end chip drivers/i2c/sx9324 register "desc" = ""SAR2 Proximity Sensor"" register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)" register "speed" = "I2C_SPEED_FAST" register "uid" = "2" register "reg_gnrl_ctrl0" = "0x16" register "reg_gnrl_ctrl1" = "0x21" register "reg_afe_ctrl0" = "0x00" register "reg_afe_ctrl1" = "0x10" register "reg_afe_ctrl2" = "0x00" register "reg_afe_ctrl3" = "0x00" register "reg_afe_ctrl4" = "0x07" register "reg_afe_ctrl5" = "0x00" register "reg_afe_ctrl6" = "0x00" register "reg_afe_ctrl7" = "0x07" register "reg_afe_ctrl8" = "0x12" register "reg_afe_ctrl9" = "0x0f" register "reg_prox_ctrl0" = "0x12" register "reg_prox_ctrl1" = "0x12" register "reg_prox_ctrl2" = "0x90" register "reg_prox_ctrl3" = "0x60" register "reg_prox_ctrl4" = "0x0c" register "reg_prox_ctrl5" = "0x12" register "reg_prox_ctrl6" = "0x3c" register "reg_prox_ctrl7" = "0x58" register "reg_adv_ctrl0" = "0x00" register "reg_adv_ctrl1" = "0x00" register "reg_adv_ctrl2" = "0x00" register "reg_adv_ctrl3" = "0x00" register "reg_adv_ctrl4" = "0x00" register "reg_adv_ctrl5" = "0x05" register "reg_adv_ctrl6" = "0x00" register "reg_adv_ctrl7" = "0x00" register "reg_adv_ctrl8" = "0x00" register "reg_adv_ctrl9" = "0x00" register "reg_adv_ctrl10" = "0x5c" register "reg_adv_ctrl11" = "0x52" register "reg_adv_ctrl12" = "0xb5" register "reg_adv_ctrl13" = "0x00" register "reg_adv_ctrl14" = "0x80" register "reg_adv_ctrl15" = "0x0c" register "reg_adv_ctrl16" = "0x38" register "reg_adv_ctrl17" = "0x56" register "reg_adv_ctrl18" = "0x33" register "reg_adv_ctrl19" = "0xf0" register "reg_adv_ctrl20" = "0xf0" device i2c 2C on end end chip drivers/intel/mipi_camera register "acpi_hid" = ""INT3478"" register "acpi_uid" = "0" register "acpi_name" = ""CAM1"" register "chip_name" = ""imx 208 Camera"" register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" register "ssdb.lanes_used" = "2" register "ssdb.link_used" = "1" register "num_freq_entries" = "2" register "link_freq[0]" = "384 * MHz" # 384 MHz register "link_freq[1]" = "96 * MHz" # 96 MHz register "remote_name" = ""IPU0"" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" register "has_power_resource" = "1" #Controls register "gpio_panel.gpio[0].gpio_num" = "GPP_C3" #PP3300_FCAM_X register "gpio_panel.gpio[1].gpio_num" = "GPP_A17" #EN_UCAM_PWR register "gpio_panel.gpio[2].gpio_num" = "GPP_F20" #reset register "gpio_panel.gpio[3].gpio_num" = "GPP_H21" #CLK_EN #_ON register "on_seq.ops_cnt" = "5" register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(3, 0)" register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" #_OFF register "off_seq.ops_cnt" = "4" register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(3, 0)" register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 10 on probe UFC UFC_MIPI_IMX208 end end chip drivers/intel/mipi_camera register "acpi_hid" = ""ACPI_DT_NAMESPACE_HID"" register "acpi_uid" = "1" register "acpi_name" = ""NVM1"" register "chip_name" = ""GT24C16S"" register "device_type" = "INTEL_ACPI_CAMERA_NVM" register "nvm_compat" = ""atmel,24c1024"" register "nvm_size" = "0x800" register "nvm_pagesize" = "0x01" register "nvm_readonly" = "0x01" register "nvm_width" = "0x08" register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D0" register "has_power_resource" = "1" #Controls register "gpio_panel.gpio[0].gpio_num" = "GPP_C3" #PP3300_FCAM_X #_ON register "on_seq.ops_cnt" = "1" register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)" #_OFF register "off_seq.ops_cnt" = "1" register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 50 on probe UFC UFC_MIPI_IMX208 end end chip drivers/i2c/generic register "hid" = ""GOOG0020"" register "desc" = ""ChromeOS HPS"" register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E7)" # EN_HPS_PWR register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E3_IRQ)" # HPS_INT_ODL # HPS uses I2C addresses 0x30 and 0x51. # The address we provide here is not significant because # neither coreboot nor Linux have a driver for HPS, # it's only used from userspace. device i2c 30 on probe HPS HPS_PRESENT end end end #I2C2 device ref i2c3 on chip drivers/i2c/hid register "generic.hid" = ""ELAN9050"" register "generic.desc" = ""ELAN Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" register "generic.detect" = "1" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" register "generic.reset_delay_ms" = "300" register "generic.reset_off_delay_ms" = "1" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "6" register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" register "generic.stop_off_delay_ms" = "1" register "generic.has_power_resource" = "1" register "hid_desc_reg_offset" = "0x01" device i2c 0x10 on end end chip drivers/i2c/hid register "generic.hid" = ""GDIX0000"" register "generic.desc" = ""Goodix Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" register "generic.detect" = "1" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" register "generic.reset_delay_ms" = "120" register "generic.reset_off_delay_ms" = "3" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "12" register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" register "generic.stop_off_delay_ms" = "1" register "generic.has_power_resource" = "1" register "hid_desc_reg_offset" = "0x01" device i2c 0x5d on end end chip drivers/i2c/hid register "generic.hid" = ""SIS9815"" register "generic.desc" = ""SIS Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" register "generic.detect" = "1" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" register "generic.stop_delay_ms" = "100" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "7" register "generic.has_power_resource" = "1" register "hid_desc_reg_offset" = "0x00" device i2c 5c on end end end #I2C3 device ref i2c5 on chip drivers/i2c/generic register "hid" = ""ELAN0000"" register "desc" = ""ELAN Touchpad"" register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" register "wake" = "GPE0_DW2_14" register "detect" = "1" device i2c 15 on end end end #I2C5 device ref hda on chip drivers/generic/max98357a register "hid" = ""MX98357A"" register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" register "sdmode_delay" = "5" device generic 0 on probe AUDIO MAX98357_ALC5682I_I2S end end chip drivers/generic/max98357a register "hid" = ""MX98360A"" register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" register "sdmode_delay" = "5" device generic 0 on probe AUDIO MAX98360_ALC5682I_I2S end end chip drivers/intel/soundwire device generic 0 on probe AUDIO MAX98373_ALC5682_SNDW chip drivers/soundwire/alc5682 # SoundWire Link 0 ID 1 register "desc" = ""Headset Codec"" device generic 0.1 on end end chip drivers/soundwire/max98373 # SoundWire Link 2 ID 3 register "desc" = ""Left Speaker Amp"" device generic 2.3 on end end chip drivers/soundwire/max98373 # SoundWire Link 2 ID 7 register "desc" = ""Right Speaker Amp"" device generic 2.7 on end end end end chip drivers/generic/nau8315 register "hid" = "NAU8318" register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" device generic 0 on probe AUDIO NAU8318_NAU88L25B_I2S end end end device ref gspi1 on chip drivers/spi/acpi register "name" = ""CRFP"" register "hid" = "ACPI_DT_NAMESPACE_HID" register "uid" = "1" register "compat_string" = ""google,cros-ec-spi"" register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" register "wake" = "GPE0_DW2_15" register "has_power_resource" = "1" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)" register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)" register "enable_delay_ms" = "3" device spi 0 hidden end end # FPMCU end device ref pch_espi on chip ec/google/chromeec use conn0 as mux_conn[0] use conn1 as mux_conn[1] use conn2 as mux_conn[2] device pnp 0c09.0 on end end end device ref pmc hidden chip drivers/intel/pmc_mux device generic 0 on chip drivers/intel/pmc_mux/conn use usb2_port1 as usb2_port use tcss_usb3_port1 as usb3_port device generic 0 alias conn0 on end end chip drivers/intel/pmc_mux/conn use usb2_port2 as usb2_port use tcss_usb3_port2 as usb3_port device generic 1 alias conn1 on end end chip drivers/intel/pmc_mux/conn use usb2_port3 as usb2_port use tcss_usb3_port3 as usb3_port device generic 2 alias conn2 on end end end end end device ref tcss_xhci on chip drivers/usb/acpi device ref tcss_root_hub on chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port C0 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))" device ref tcss_usb3_port1 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port C1 (DB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" register "usb_lpm_incapable" = "true" device ref tcss_usb3_port2 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port C2 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" device ref tcss_usb3_port3 on end end end end end device ref xhci on chip drivers/usb/acpi device ref xhci_root_hub on chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port C0 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))" device ref usb2_port1 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port C1 (DB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" device ref usb2_port2 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port C2 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" device ref usb2_port3 on end end chip drivers/usb/acpi register "desc" = ""USB2 WWAN"" register "type" = "UPC_TYPE_INTERNAL" device ref usb2_port4 on end end chip drivers/usb/acpi register "desc" = ""USB2 Camera"" register "type" = "UPC_TYPE_INTERNAL" device ref usb2_port6 on probe UFC UFC_USB end end chip drivers/usb/acpi register "desc" = ""USB2 Type-A Port A0 (DB)"" register "type" = "UPC_TYPE_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))" device ref usb2_port9 on end end chip drivers/usb/acpi register "desc" = ""USB2 Bluetooth"" register "type" = "UPC_TYPE_INTERNAL" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" device ref usb2_port10 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-A Port A0 (DB)"" register "type" = "UPC_TYPE_USB3_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))" device ref usb3_port1 on end end chip drivers/usb/acpi register "desc" = ""USB3 WWAN"" register "type" = "UPC_TYPE_INTERNAL" device ref usb3_port4 on end end end end end end end