fw_config field DB_USB 0 1 option DB_NONE 0 option DB_1C_1A 1 option DB_1C 2 option DB_1C_LTE 3 end field WIFI_SAR_ID 2 3 option SAR_ID_0 0 option SAR_ID_1 1 option SAR_ID_2 2 option SAR_ID_3 3 end field STYLUS 9 option STYLUS_ABSENT 0 option STYLUS_PRESENT 1 end field SD_CARD 10 option SD_PRESENT 0 option SD_ABSENT 1 end field WFC 11 option WFC_ABSENT 0 option WFC_PRESENT 1 end field WIFI_SAR_ID2 16 19 option INTEL_QUANDISO_LTE 0 option INTEL_QUANDISO_WIFI 1 option INTEL_QUANDISO360_LTE 2 option INTEL_QUANDISO360_WIFI 3 option UNUSED 15 end end chip soc/intel/alderlake register "sagv" = "SaGv_Enabled" # EMMC Tx CMD Delay # Refer to EDS-Vol2-42.3.7. # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" # EMMC TX DATA Delay 1 # Refer to EDS-Vol2-42.3.8. # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" # EMMC TX DATA Delay 2 # Refer to EDS-Vol2-42.3.9. # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C272828" # EMMC RX CMD/DATA Delay 1 # Refer to EDS-Vol2-42.3.10. # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C171733" # EMMC RX CMD/DATA Delay 2 # Refer to EDS-Vol2-42.3.12. # [17:16] stands for Rx Clock before Output Buffer, # 00: Rx clock after output buffer, # 01: Rx clock before output buffer, # 10: Automatic selection based on working mode. # 11: Reserved # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10024" # EMMC Rx Strobe Delay # Refer to EDS-Vol2-42.3.11. # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1414" # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC. # Bit 2 - C1 has a redriver which does SBU muxing. # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1. register "tcss_aux_ori" = "1" register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # USB2 WWAN register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # Rear Camera register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 WWAN # Configure external V1P05/Vnn/VnnSx Rails register "ext_fivr_settings" = "{ .configure_ext_fivr = 1, }" # Intel Common SoC Config #+-------------------+---------------------------+ #| Field | Value | #+-------------------+---------------------------+ #| I2C0 | TPM. Early init is | #| | required to set up a BAR | #| | for TPM communication | #| I2C1 | Touchscreen | #| I2C2 | P-sensor | #| I2C3 | Audio | #| I2C5 | Trackpad | #+-------------------+---------------------------+ register "common_soc_config" = "{ .i2c[0] = { .early_init = 1, .speed = I2C_SPEED_FAST_PLUS, .speed_config[0] = { .speed = I2C_SPEED_FAST_PLUS, .scl_lcnt = 56, .scl_hcnt = 30, .sda_hold = 7, } }, .i2c[1] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 158, .scl_hcnt = 79, .sda_hold = 30, } }, .i2c[2] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 158, .scl_hcnt = 79, .sda_hold = 7, } }, .i2c[3] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 158, .scl_hcnt = 79, .sda_hold = 7, } }, .i2c[5] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 158, .scl_hcnt = 79, .sda_hold = 40, } }, }" device domain 0 on device ref dtt on chip drivers/intel/dptf ## sensor information register "options.tsr[0].desc" = ""CPU"" register "options.tsr[1].desc" = ""5V Regulator"" register "options.tsr[2].desc" = ""Charger"" # TODO: below values are initial reference values only ## Passive Policy register "policies.passive" = "{ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), }" ## Critical Policy register "policies.critical" = "{ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), }" register "controls.power_limits" = "{ .pl1 = { .min_power = 3000, .max_power = 6000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 200 }, .pl2 = { .min_power = 25000, .max_power = 25000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 1000 } }" ## Charger Performance Control (Control, mA) register "controls.charger_perf" = "{ [0] = { 255, 1700 }, [1] = { 24, 1500 }, [2] = { 16, 1000 }, [3] = { 8, 500 } }" device generic 0 on end end end device ref cnvi_wifi on chip drivers/wifi/generic register "enable_cnvi_ddr_rfim" = "true" device generic 0 on end end end device ref i2c1 on chip drivers/i2c/generic register "hid" = ""ELAN0001"" register "desc" = ""ELAN Touchscreen"" register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" register "detect" = "1" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" register "reset_delay_ms" = "20" register "reset_off_delay_ms" = "2" register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" register "stop_delay_ms" = "280" register "stop_off_delay_ms" = "2" register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "enable_delay_ms" = "1" register "has_power_resource" = "1" device i2c 10 on end end chip drivers/i2c/hid register "generic.hid" = ""ELAN2513"" register "generic.desc" = ""ELAN Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" register "generic.detect" = "1" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" register "generic.reset_delay_ms" = "20" register "generic.reset_off_delay_ms" = "2" register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" register "generic.stop_delay_ms" = "280" register "generic.stop_off_delay_ms" = "2" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "1" register "generic.has_power_resource" = "1" register "hid_desc_reg_offset" = "0x01" device i2c 15 on end end chip drivers/i2c/hid register "generic.hid" = ""GTCH7503"" register "generic.desc" = ""G2TOUCH Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" register "generic.detect" = "1" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" register "generic.reset_delay_ms" = "50" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "1" register "generic.has_power_resource" = "1" register "hid_desc_reg_offset" = "0x01" device i2c 40 on end end chip drivers/generic/gpio_keys register "name" = ""PENH"" register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)" register "key.wake_gpe" = "GPE0_DW2_15" register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" register "key.dev_name" = ""EJCT"" register "key.linux_code" = "SW_PEN_INSERTED" register "key.linux_input_type" = "EV_SW" register "key.label" = ""pen_eject"" device generic 0 on probe STYLUS STYLUS_PRESENT end end end device ref i2c2 on chip drivers/i2c/sx9324 register "desc" = ""SAR Proximity Sensor"" register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)" register "speed" = "I2C_SPEED_FAST" register "uid" = "1" register "reg_gnrl_ctrl0" = "0x16" register "reg_gnrl_ctrl1" = "0x21" register "reg_afe_ctrl0" = "0x00" register "reg_afe_ctrl1" = "0x10" register "reg_afe_ctrl2" = "0x00" register "reg_afe_ctrl3" = "0x00" register "reg_afe_ctrl4" = "0x07" register "reg_afe_ctrl5" = "0x00" register "reg_afe_ctrl6" = "0x00" register "reg_afe_ctrl7" = "0x07" register "reg_afe_ctrl8" = "0x12" register "reg_afe_ctrl9" = "0x0f" register "reg_prox_ctrl0" = "0x12" register "reg_prox_ctrl1" = "0x12" register "reg_prox_ctrl2" = "0x90" register "reg_prox_ctrl3" = "0x60" register "reg_prox_ctrl4" = "0x0c" register "reg_prox_ctrl5" = "0x12" register "reg_prox_ctrl6" = "0x3c" register "reg_prox_ctrl7" = "0x58" register "reg_adv_ctrl0" = "0x00" register "reg_adv_ctrl1" = "0x00" register "reg_adv_ctrl2" = "0x00" register "reg_adv_ctrl3" = "0x00" register "reg_adv_ctrl4" = "0x00" register "reg_adv_ctrl5" = "0x05" register "reg_adv_ctrl6" = "0x00" register "reg_adv_ctrl7" = "0x00" register "reg_adv_ctrl8" = "0x00" register "reg_adv_ctrl9" = "0x00" register "reg_adv_ctrl10" = "0x5c" register "reg_adv_ctrl11" = "0x52" register "reg_adv_ctrl12" = "0xb5" register "reg_adv_ctrl13" = "0x00" register "reg_adv_ctrl14" = "0x80" register "reg_adv_ctrl15" = "0x0c" register "reg_adv_ctrl16" = "0x38" register "reg_adv_ctrl17" = "0x56" register "reg_adv_ctrl18" = "0x33" register "reg_adv_ctrl19" = "0xf0" register "reg_adv_ctrl20" = "0xf0" device i2c 28 on probe DB_USB DB_1C_LTE end end end device ref i2c3 on chip drivers/i2c/generic register "hid" = ""RTL5682"" register "name" = ""RT58"" register "desc" = ""Headset Codec"" register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" # Set the jd_src to RT5668_JD1 for jack detection register "property_count" = "1" register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" register "property_list[0].name" = ""realtek,jd-src"" register "property_list[0].integer" = "1" device i2c 1a on end end end device ref i2c5 on chip drivers/i2c/generic register "hid" = ""ELAN0000"" register "desc" = ""ELAN Touchpad"" register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" register "wake" = "GPE0_DW2_14" register "detect" = "1" device i2c 15 on end end chip drivers/i2c/hid register "generic.hid" = ""SYNA0000"" register "generic.cid" = ""ACPI0C50"" register "generic.desc" = ""Synaptics Touchpad"" register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" register "generic.wake" = "GPE0_DW2_14" register "generic.detect" = "1" register "hid_desc_reg_offset" = "0x20" device i2c 0x2c on end end end device ref hda on chip drivers/generic/max98357a register "hid" = ""MX98360A"" register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" register "sdmode_delay" = "5" device generic 0 on end end end device ref pcie_rp4 on # PCIe 4 WLAN register "pch_pcie_rp[PCH_RP(4)]" = "{ .clk_src = 2, .clk_req = 2, .flags = PCIE_RP_LTR | PCIE_RP_AER, }" chip drivers/wifi/generic register "wake" = "GPE0_DW1_03" register "add_acpi_dma_property" = "true" device pci 00.0 on end end end device ref pcie_rp7 on # Enable SD Card PCIe 7 using clk 3 register "pch_pcie_rp[PCH_RP(7)]" = "{ .clk_src = 3, .clk_req = 3, .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER, }" chip soc/intel/common/block/pcie/rtd3 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)" register "srcclk_pin" = "3" device generic 0 on end end probe SD_CARD SD_PRESENT end device ref emmc on end device ref ish on chip drivers/intel/ish register "add_acpi_dma_property" = "true" device generic 0 on end end end device ref ufs on end device ref pch_espi on chip ec/google/chromeec use conn0 as mux_conn[0] use conn1 as mux_conn[1] device pnp 0c09.0 on end end end device ref pmc hidden chip drivers/intel/pmc_mux device generic 0 on chip drivers/intel/pmc_mux/conn use usb2_port1 as usb2_port use tcss_usb3_port1 as usb3_port device generic 0 alias conn0 on end end chip drivers/intel/pmc_mux/conn use usb2_port2 as usb2_port use tcss_usb3_port2 as usb3_port device generic 1 alias conn1 on end end end end end device ref tcss_xhci on chip drivers/usb/acpi device ref tcss_root_hub on chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port C0 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" device ref tcss_usb3_port1 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port C1 (DB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" device ref tcss_usb3_port2 on end end end end end device ref xhci on chip drivers/usb/acpi device ref xhci_root_hub on chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port C0 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" device ref usb2_port1 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port C1 (DB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" device ref usb2_port2 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-A Port A0 (MLB)"" register "type" = "UPC_TYPE_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))" device ref usb2_port3 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-A Port A1 (DB)"" register "type" = "UPC_TYPE_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" device ref usb2_port4 on probe DB_USB DB_1C_1A end end chip drivers/usb/acpi register "desc" = ""USB2 WWAN"" register "type" = "UPC_TYPE_INTERNAL" device ref usb2_port4 on probe DB_USB DB_1C_LTE end end chip drivers/usb/acpi register "desc" = ""USB2 UFC"" register "type" = "UPC_TYPE_INTERNAL" device ref usb2_port6 on end end chip drivers/usb/acpi register "desc" = ""USB2 WF Camera"" register "type" = "UPC_TYPE_INTERNAL" device ref usb2_port7 on probe WFC WFC_PRESENT end end chip drivers/usb/acpi register "desc" = ""USB2 Bluetooth"" register "type" = "UPC_TYPE_INTERNAL" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" device ref usb2_port8 on end end chip drivers/usb/acpi register "desc" = ""CNVi Bluetooth"" register "type" = "UPC_TYPE_INTERNAL" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" device ref usb2_port10 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-A Port A0 (MLB)"" register "type" = "UPC_TYPE_USB3_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))" device ref usb3_port1 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-A Port A1 (DB)"" register "type" = "UPC_TYPE_USB3_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" device ref usb3_port2 on probe DB_USB DB_1C_1A end end chip drivers/usb/acpi register "desc" = ""USB3 WWAN"" register "type" = "UPC_TYPE_INTERNAL" device ref usb3_port2 on probe DB_USB DB_1C_LTE end end end end end end end