fw_config
field DB_USB 0 3
option USB_ABSENT 0
option USB3_PS8811 1
end
field DB_SD 4 5
option SD_ABSENT 0
option SD_GL9755S 1
end
field KB_BL 7 7
option KB_BL_ABSENT 0
option KB_BL_PRESENT 1
end
field AUDIO 8 10
option AUDIO_UNKNOWN 0
option MAX98360_ALC5682I_I2S 1
option MAX98360_ALC5682I_VS_I2S 2
end
field DB_LTE 11 12
option LTE_ABSENT 0
option LTE_USB 1
end
end
chip soc/intel/alderlake
register "sagv" = "SaGv_Enabled"
register "max_dram_speed_mts" = "3733"
# Acoustic settings
register "acoustic_noise_mitigation" = "1"
register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8"
register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8"
register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1"
register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI1 | Fingerprint MCU |
#| I2C0 | Audio |
#| I2C1 | Touchscreen |
#| I2C2 | |
#| I2C3 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| I2C5 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.i2c[0] = {
.speed = I2C_SPEED_FAST,
},
.i2c[1] = {
.speed = I2C_SPEED_FAST,
},
.i2c[2] = {
.speed = I2C_SPEED_FAST,
},
.i2c[3] = {
.early_init = 1,
.speed = I2C_SPEED_FAST,
},
.i2c[5] = {
.speed = I2C_SPEED_FAST,
},
}"
register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2_C1
register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MLB Port
register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port
register "usb3_ports[2]" = "USB3_PORT_EMPTY"
register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)"
device domain 0 on
device ref dtt on
chip drivers/intel/dptf
## sensor information
register "options.tsr[0].desc" = ""CPU""
register "options.tsr[1].desc" = ""SSD""
register "options.tsr[2].desc" = ""CHARGER""
register "options.tsr[3].desc" = ""MEMORY""
register "options.tsr[4].desc" = ""TYPEC""
# TODO: below values are initial reference values only
## Passive Policy
register "policies.passive" = "{
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 90, 5000),
[2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 92, 5000),
[3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 90, 5000),
[4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 90, 5000),
[5] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_4, 90, 5000),
}"
## Critical Policy
register "policies.critical" = "{
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 89, SHUTDOWN),
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
[4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN),
[5] = DPTF_CRITICAL(TEMP_SENSOR_4, 85, SHUTDOWN),
}"
register "controls.power_limits" = "{
.pl1 = {
.min_power = 3000,
.max_power = 15000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 250,
},
.pl2 = {
.min_power = 55000,
.max_power = 55000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000,
}
}"
## Charger Performance Control (Control, mA)
register "controls.charger_perf" = "{
[0] = { 255, 1700 },
[1] = { 24, 1500 },
[2] = { 16, 1000 },
[3] = { 8, 500 }
}"
device generic 0 alias dptf_policy on end
end
end
device ref cnvi_wifi on
chip drivers/wifi/generic
register "wake" = "GPE0_PME_B0"
device generic 0 on end
end
end
device ref pcie_rp3 on
chip soc/intel/common/block/pcie/rtd3
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B3)"
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E20)"
register "srcclk_pin" = "6"
register "reset_delay_ms" = "50"
register "enable_delay_ms" = "20"
device generic 0 alias emmc_rtd3 on end
end
# Enable PCIe-to-eMMC bridge PCIE 3 using clk 6
register "pch_pcie_rp[PCH_RP(3)]" = "{
.clk_src = 6,
.clk_req = 6,
.flags = PCIE_RP_LTR | PCIE_RP_AER,
}"
end #PCIE3 BH799BB
device ref tcss_dma0 on
chip drivers/intel/usb4/retimer
register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
use tcss_usb3_port1 as dfp[0].typec_port
device generic 0 on end
end
end
device ref tcss_dma1 on
chip drivers/intel/usb4/retimer
register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
use tcss_usb3_port3 as dfp[0].typec_port
device generic 0 on end
end
end
device ref pcie_rp6 off end #PCIE6 WWAN
device ref pcie_rp8 on
chip soc/intel/common/block/pcie/rtd3
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)"
register "srcclk_pin" = "3"
device generic 0 on end
end
end #PCIE8 SD card
device ref pcie_rp9 on
# Enable NVMe PCIE 9 using clk 0
register "pch_pcie_rp[PCH_RP(9)]" = "{
.clk_src = 0,
.clk_req = 0,
.flags = PCIE_RP_LTR | PCIE_RP_AER,
}"
end #PCIE9-12 SSD
device ref i2c0 on
chip drivers/i2c/generic
register "hid" = ""10EC5682""
register "name" = ""RT58""
register "desc" = ""Headset Codec""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a alias audio_codec on
probe AUDIO MAX98360_ALC5682I_I2S
probe AUDIO MAX98360_ALC5682I_VS_I2S
end
end
end #I2C0
device ref i2c1 on
chip drivers/i2c/hid
register "generic.hid" = ""ELAN9050""
register "generic.desc" = ""ELAN Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
register "generic.reset_delay_ms" = "200"
register "generic.reset_off_delay_ms" = "1"
register "generic.enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
register "generic.enable_delay_ms" = "6"
register "generic.stop_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
register "generic.stop_off_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "generic.disable_gpio_export_in_crs" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 0x10 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""GTCH7503""
register "generic.desc" = ""G2TOUCH Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
register "generic.reset_delay_ms" = "50"
register "generic.enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
register "generic.enable_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "generic.disable_gpio_export_in_crs" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 0x40 on end
end
end
device ref i2c3 on
chip drivers/i2c/tpm
register "hid" = ""GOOG0005""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
device i2c 50 on end
end
end
device ref i2c5 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
register "wake" = "GPE0_DW2_14"
register "detect" = "1"
device i2c 15 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""GXTP7288""
register "generic.desc" = ""Goodix Touchpad""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)"
register "generic.wake" = "GPE0_DW2_14"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 2c on end
end
end
device ref hda on
chip drivers/generic/max98357a
register "hid" = ""MX98360A""
register "sdmode_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
register "sdmode_delay" = "5"
device generic 0 on
probe AUDIO MAX98360_ALC5682I_I2S
probe AUDIO MAX98360_ALC5682I_VS_I2S
end
end
end
device ref gspi1 on
chip drivers/spi/acpi
register "name" = ""CRFP""
register "hid" = "ACPI_DT_NAMESPACE_HID"
register "uid" = "1"
register "compat_string" = ""google,cros-ec-spi""
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)"
register "wake" = "GPE0_DW2_15"
register "has_power_resource" = "1"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)"
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)"
register "enable_delay_ms" = "3"
device spi 0 on end
end # FPMCU
end
device ref pch_espi on
chip ec/google/chromeec
use conn0 as mux_conn[0]
use conn1 as mux_conn[1]
device pnp 0c09.0 on end
end
end
device ref pmc hidden
chip drivers/intel/pmc_mux
device generic 0 on
chip drivers/intel/pmc_mux/conn
use usb2_port1 as usb2_port
use tcss_usb3_port1 as usb3_port
device generic 0 alias conn0 on end
end
chip drivers/intel/pmc_mux/conn
use usb2_port3 as usb2_port
use tcss_usb3_port3 as usb3_port
device generic 1 alias conn1 on end
end
end
end
end
device ref tcss_xhci on
chip drivers/usb/acpi
device ref tcss_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, CENTER, ACPI_PLD_GROUP(1, 1))"
device ref tcss_usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C2 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(2, 1))"
device ref tcss_usb3_port3 on end
end
end
end
end
device ref xhci on
chip drivers/usb/acpi
device ref xhci_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, CENTER, ACPI_PLD_GROUP(1, 1))"
device ref usb2_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C2 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(2, 1))"
device ref usb2_port3 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port4 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Camera""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port6 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port (MLB)""
register "type" = "UPC_TYPE_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
device ref usb2_port8 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port A0 (DB)""
register "type" = "UPC_TYPE_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
device ref usb2_port9 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
device ref usb2_port10 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port A0 (DB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
device ref usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port (MLB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
device ref usb3_port2 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb3_port4 on end
end
end
end
end
end
end