fw_config field DB_USB 0 1 option DB_NONE 0 option DB_1C_1A 1 option DB_1C_LTE 2 end field THERMAL_SOLUTION 2 option THERMAL_SOLUTION_PASSIVE 0 option THERMAL_SOLUTION_ACTIVE 1 end field SD_CARD 4 option SD_GL9750S 0 option SD_ABSENT 1 end field WFC 5 option WFC_MIPI_OVTI5675 0 option WFC_ABSENT 1 end field STYLUS 6 option STYLUS_PRESENT 0 option STYLUS_ABSENT 1 end field WIFI_CATEGORY 7 option WIFI_6 0 # CNVi option WIFI_7 1 # PCIe end end chip soc/intel/alderlake register "sagv" = "SaGv_Enabled" # SOC Aux orientation override: # This is a bitfield that corresponds to up to 4 TCSS ports. # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. # TcssAuxOri = 0101b # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the # motherboard to USBC connector register "tcss_aux_ori" = "5" register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN (WIFI6) register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for WIFI PCIE (WIFI7) # Configure external V1P05/Vnn/VnnSx Rails register "ext_fivr_settings" = "{ .configure_ext_fivr = 1, .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE, .v1p05_voltage_mv = 1050, .vnn_voltage_mv = 780, .vnn_sx_voltage_mv = 1050, .v1p05_icc_max_ma = 500, .vnn_icc_max_ma = 500, }" # Enable the Cnvi BT Audio Offload register "cnvi_bt_audio_offload" = "1" # Intel Common SoC Config #+-------------------+---------------------------+ #| Field | Value | #+-------------------+---------------------------+ #| I2C0 | TPM. Early init is | #| | required to set up a BAR | #| | for TPM communication | #| I2C1 | Touchscreen | #| I2C2 | Sub-board(PSensor)/WCAM | #| I2C3 | Audio | #| I2C5 | Trackpad | #+-------------------+---------------------------+ register "common_soc_config" = "{ .i2c[0] = { .early_init = 1, .speed = I2C_SPEED_FAST_PLUS, .speed_config[0] = { .speed = I2C_SPEED_FAST_PLUS, .scl_lcnt = 55, .scl_hcnt = 30, .sda_hold = 7, } }, .i2c[1] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 157, .scl_hcnt = 79, .sda_hold = 7, } }, .i2c[2] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 157, .scl_hcnt = 79, .sda_hold = 7, } }, .i2c[3] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 158, .scl_hcnt = 79, .sda_hold = 7, } }, .i2c[5] = { .speed = I2C_SPEED_FAST, .speed_config[0] = { .speed = I2C_SPEED_FAST, .scl_lcnt = 158, .scl_hcnt = 79, .sda_hold = 7, } }, }" device domain 0 on device ref dtt on chip drivers/intel/dptf ## sensor information register "options.tsr[0].desc" = ""Memory"" register "options.tsr[1].desc" = ""Charger"" register "options.tsr[2].desc" = ""Ambient"" # TODO: below values are initial reference values only ## Passive Policy register "policies.passive" = "{ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), }" ## Critical Policy register "policies.critical" = "{ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), }" register "controls.power_limits" = "{ .pl1 = { .min_power = 3000, .max_power = 6000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 200 }, .pl2 = { .min_power = 25000, .max_power = 25000, .time_window_min = 1, .time_window_max = 1, .granularity = 1000 } }" ## Charger Performance Control (Control, mA) register "controls.charger_perf" = "{ [0] = { 255, 1700 }, [1] = { 24, 1500 }, [2] = { 16, 1000 }, [3] = { 8, 500 } }" device generic 0 on probe THERMAL_SOLUTION THERMAL_SOLUTION_PASSIVE end end chip drivers/intel/dptf ## sensor information register "options.tsr[0].desc" = ""Memory"" register "options.tsr[1].desc" = ""Charger"" register "options.tsr[2].desc" = ""Ambient"" # TODO: below values are initial reference values only ## Active Policy register "policies.active" = "{ [0] = { .target = DPTF_CPU, .thresholds = { TEMP_PCT(85, 90), TEMP_PCT(80, 80), TEMP_PCT(75, 70), TEMP_PCT(70, 50), TEMP_PCT(65, 30), } }, [1] = { .target = DPTF_TEMP_SENSOR_2, .thresholds = { TEMP_PCT(50, 90), TEMP_PCT(48, 70), TEMP_PCT(46, 60), TEMP_PCT(43, 40), TEMP_PCT(40, 30), } } }" # TODO: below values are initial reference values only ## Passive Policy register "policies.passive" = "{ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), }" ## Critical Policy register "policies.critical" = "{ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), }" register "controls.power_limits" = "{ .pl1 = { .min_power = 12000, .max_power = 15000, .time_window_min = 28 * MSECS_PER_SEC, .time_window_max = 32 * MSECS_PER_SEC, .granularity = 200 }, .pl2 = { .min_power = 35000, .max_power = 35000, .time_window_min = 1, .time_window_max = 1, .granularity = 1000 } }" ## Charger Performance Control (Control, mA) register "controls.charger_perf" = "{ [0] = { 255, 1700 }, [1] = { 24, 1500 }, [2] = { 16, 1000 }, [3] = { 8, 500 } }" ## Fan Performance Control (Percent, Speed, Noise, Power) register "controls.fan_perf" = "{ [0] = { 100, 6000, 220, 2200, }, [1] = { 92, 5500, 180, 1800, }, [2] = { 85, 5000, 145, 1450, }, [3] = { 70, 4400, 115, 1150, }, [4] = { 56, 3900, 90, 900, }, [5] = { 45, 3300, 55, 550, }, [6] = { 38, 3000, 30, 300, }, [7] = { 33, 2900, 15, 150, }, [8] = { 10, 800, 10, 100, }, [9] = { 0, 0, 0, 50, } }" ## Fan options register "options.fan.fine_grained_control" = "1" register "options.fan.step_size" = "2" device generic 1 on probe THERMAL_SOLUTION THERMAL_SOLUTION_ACTIVE end end end device ref ipu on chip drivers/intel/mipi_camera register "acpi_uid" = "0x50000" register "acpi_name" = ""IPU0"" register "device_type" = "INTEL_ACPI_CAMERA_CIO2" register "cio2_num_ports" = "1" register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" register "cio2_prt[0]" = "1" device generic 0 on end end probe WFC WFC_MIPI_OVTI5675 end device ref cnvi_wifi on chip drivers/wifi/generic register "wake" = "GPE0_PME_B0" register "add_acpi_dma_property" = "true" register "enable_cnvi_ddr_rfim" = "true" device generic 0 on end end probe WIFI_CATEGORY WIFI_6 end device ref i2c1 on chip drivers/i2c/hid register "generic.hid" = ""ELAN6915"" register "generic.desc" = ""ELAN Touchscreen"" register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" register "generic.detect" = "1" register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" register "generic.reset_delay_ms" = "20" register "generic.reset_off_delay_ms" = "2" register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" register "generic.stop_delay_ms" = "280" register "generic.stop_off_delay_ms" = "2" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "1" register "generic.has_power_resource" = "1" register "hid_desc_reg_offset" = "0x01" device i2c 15 on end end chip drivers/generic/gpio_keys register "name" = ""PENH"" register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)" register "key.wake_gpe" = "GPE0_DW2_15" register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" register "key.dev_name" = ""EJCT"" register "key.linux_code" = "SW_PEN_INSERTED" register "key.linux_input_type" = "EV_SW" register "key.label" = ""pen_eject"" device generic 0 on probe STYLUS STYLUS_PRESENT end end end device ref i2c2 on chip drivers/i2c/sx9324 register "desc" = ""SAR Proximity Sensor"" register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)" register "speed" = "I2C_SPEED_FAST" register "uid" = "1" register "reg_gnrl_ctrl0" = "0x16" register "reg_gnrl_ctrl1" = "0x21" register "reg_afe_ctrl0" = "0x00" register "reg_afe_ctrl1" = "0x10" register "reg_afe_ctrl2" = "0x00" register "reg_afe_ctrl3" = "0x00" register "reg_afe_ctrl4" = "0x07" register "reg_afe_ctrl5" = "0x00" register "reg_afe_ctrl6" = "0x00" register "reg_afe_ctrl7" = "0x07" register "reg_afe_ctrl8" = "0x12" register "reg_afe_ctrl9" = "0x0f" register "reg_prox_ctrl0" = "0x12" register "reg_prox_ctrl1" = "0x12" register "reg_prox_ctrl2" = "0x90" register "reg_prox_ctrl3" = "0x60" register "reg_prox_ctrl4" = "0x0c" register "reg_prox_ctrl5" = "0x12" register "reg_prox_ctrl6" = "0x3c" register "reg_prox_ctrl7" = "0x58" register "reg_adv_ctrl0" = "0x00" register "reg_adv_ctrl1" = "0x00" register "reg_adv_ctrl2" = "0x00" register "reg_adv_ctrl3" = "0x00" register "reg_adv_ctrl4" = "0x00" register "reg_adv_ctrl5" = "0x05" register "reg_adv_ctrl6" = "0x00" register "reg_adv_ctrl7" = "0x00" register "reg_adv_ctrl8" = "0x00" register "reg_adv_ctrl9" = "0x00" register "reg_adv_ctrl10" = "0x5c" register "reg_adv_ctrl11" = "0x52" register "reg_adv_ctrl12" = "0xb5" register "reg_adv_ctrl13" = "0x00" register "reg_adv_ctrl14" = "0x80" register "reg_adv_ctrl15" = "0x0c" register "reg_adv_ctrl16" = "0x38" register "reg_adv_ctrl17" = "0x56" register "reg_adv_ctrl18" = "0x33" register "reg_adv_ctrl19" = "0xf0" register "reg_adv_ctrl20" = "0xf0" device i2c 28 on probe DB_USB DB_1C_LTE end end chip drivers/intel/mipi_camera register "acpi_hid" = ""OVTI5675"" register "acpi_uid" = "0" register "acpi_name" = ""CAM0"" register "chip_name" = ""Ov 5675 Camera"" register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" register "ssdb.lanes_used" = "2" register "ssdb.link_used" = "1" register "ssdb.vcm_type" = "0x0C" register "vcm_name" = ""VCM0"" register "num_freq_entries" = "1" register "link_freq[0]" = "DEFAULT_LINK_FREQ" register "remote_name" = ""IPU0"" register "has_power_resource" = "1" #Controls register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L #_ON register "on_seq.ops_cnt" = "5" register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" #_OFF register "off_seq.ops_cnt" = "4" register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" device i2c 36 on probe WFC WFC_MIPI_OVTI5675 end end chip drivers/intel/mipi_camera register "acpi_uid" = "3" register "acpi_name" = ""VCM0"" register "chip_name" = ""DW AF DAC"" register "device_type" = "INTEL_ACPI_CAMERA_VCM" register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC"" register "vcm_compat" = ""dongwoon,dw9714"" device i2c 0C on probe WFC WFC_MIPI_OVTI5675 end end chip drivers/intel/mipi_camera register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" register "acpi_uid" = "1" register "acpi_name" = ""NVM0"" register "chip_name" = ""GT24C08"" register "device_type" = "INTEL_ACPI_CAMERA_NVM" register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC"" register "nvm_size" = "0x2000" register "nvm_pagesize" = "1" register "nvm_readonly" = "1" register "nvm_width" = "0x10" register "nvm_compat" = ""atmel,24c08"" device i2c 50 on probe WFC WFC_MIPI_OVTI5675 end end end device ref i2c3 on chip drivers/i2c/nau8825 register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" register "jkdet_enable" = "1" register "jkdet_pull_enable" = "0" register "jkdet_polarity" = "1" # ActiveLow register "vref_impedance" = "2" # 125kOhm register "micbias_voltage" = "6" # 2.754 register "sar_threshold_num" = "4" register "sar_threshold[0]" = "0x0c" register "sar_threshold[1]" = "0x1c" register "sar_threshold[2]" = "0x38" register "sar_threshold[3]" = "0x60" register "sar_hysteresis" = "1" register "sar_voltage" = "0" # VDDA register "sar_compare_time" = "0" # 500ns register "sar_sampling_time" = "0" # 2us register "short_key_debounce" = "2" # 100ms register "jack_insert_debounce" = "7" # 512ms register "jack_eject_debounce" = "7" # 512ms register "adcout_ds" = "true" device i2c 1a on end end end device ref i2c5 on chip drivers/i2c/generic register "hid" = ""ELAN0000"" register "desc" = ""ELAN Touchpad"" register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" register "wake" = "GPE0_DW2_14" register "detect" = "1" device i2c 15 on end end end device ref hda on chip drivers/generic/max98357a register "hid" = ""MX98360A"" register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" register "sdmode_delay" = "5" device generic 0 on end end chip drivers/sof register "spkr_tplg" = "max98360a" register "jack_tplg" = "nau8825" register "mic_tplg" = "_2ch_pdm0" device generic 0 on end end end device ref pcie_rp4 on probe WIFI_CATEGORY WIFI_7 # Enable WLAN Card PCIE 4 using clk 2 register "pch_pcie_rp[PCH_RP(4)]" = "{ .clk_src = 2, .clk_req = 2, .flags = PCIE_RP_LTR | PCIE_RP_AER, }" chip drivers/wifi/generic register "wake" = "GPE0_DW1_03" register "add_acpi_dma_property" = "true" use usb2_port8 as bluetooth_companion device pci 00.0 on probe WIFI_CATEGORY WIFI_7 end end chip soc/intel/common/block/pcie/rtd3 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)" register "srcclk_pin" = "2" device generic 0 on probe WIFI_CATEGORY WIFI_7 end end end #PCIE4 WLAN card device ref pcie_rp7 on # Enable SD Card PCIe 7 using clk 3 register "pch_pcie_rp[PCH_RP(7)]" = "{ .clk_src = 3, .clk_req = 3, .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER, }" chip soc/intel/common/block/pcie/rtd3 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)" register "srcclk_pin" = "3" device generic 0 on end end probe SD_CARD SD_GL9750S end device ref pcie_rp9 on # Enable NVMe SSD PCIe 9-12 using clk 1 register "pch_pcie_rp[PCH_RP(9)]" = "{ .clk_src = 1, .clk_req = 1, .flags = PCIE_RP_LTR | PCIE_RP_AER, }" probe STORAGE STORAGE_NVME end device ref emmc on probe STORAGE STORAGE_EMMC end device ref ish on chip drivers/intel/ish register "add_acpi_dma_property" = "true" device generic 0 on end end probe STORAGE STORAGE_UFS end device ref ufs on probe STORAGE STORAGE_UFS end device ref pch_espi on chip ec/google/chromeec use conn0 as mux_conn[0] use conn1 as mux_conn[1] device pnp 0c09.0 on end end end device ref pmc hidden chip drivers/intel/pmc_mux device generic 0 on chip drivers/intel/pmc_mux/conn use usb2_port1 as usb2_port use tcss_usb3_port1 as usb3_port device generic 0 alias conn0 on end end chip drivers/intel/pmc_mux/conn use usb2_port2 as usb2_port use tcss_usb3_port2 as usb3_port device generic 1 alias conn1 on end end end end end device ref tcss_xhci on chip drivers/usb/acpi device ref tcss_root_hub on chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port C0 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" device ref tcss_usb3_port1 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-C Port C1 (DB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" device ref tcss_usb3_port2 on end end end end end device ref xhci on chip drivers/usb/acpi device ref xhci_root_hub on chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port C0 (MLB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" device ref usb2_port1 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-C Port C1 (DB)"" register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" device ref usb2_port2 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-A Port A0 (MLB)"" register "type" = "UPC_TYPE_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" device ref usb2_port3 on end end chip drivers/usb/acpi register "desc" = ""USB2 Type-A Port A1 (DB)"" register "type" = "UPC_TYPE_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" device ref usb2_port4 on probe DB_USB DB_1C_1A end end chip drivers/usb/acpi register "desc" = ""USB2 WWAN"" register "type" = "UPC_TYPE_INTERNAL" device ref usb2_port4 on probe DB_USB DB_1C_LTE end end chip drivers/usb/acpi register "desc" = ""USB2 Camera"" register "type" = "UPC_TYPE_INTERNAL" device ref usb2_port6 on end end chip drivers/usb/acpi register "desc" = ""USB2 Bluetooth"" register "type" = "UPC_TYPE_INTERNAL" register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" device ref usb2_port10 on probe WIFI_CATEGORY WIFI_6 end device ref usb2_port8 on probe WIFI_CATEGORY WIFI_7 end end chip drivers/usb/acpi register "desc" = ""USB3 Type-A Port A0 (MLB)"" register "type" = "UPC_TYPE_USB3_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" device ref usb3_port1 on end end chip drivers/usb/acpi register "desc" = ""USB3 Type-A Port A1 (DB)"" register "type" = "UPC_TYPE_USB3_A" register "use_custom_pld" = "true" register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" device ref usb3_port2 on probe DB_USB DB_1C_1A end end chip drivers/usb/acpi register "desc" = ""USB3 WWAN"" register "type" = "UPC_TYPE_INTERNAL" device ref usb3_port2 on probe DB_USB DB_1C_LTE end end end end end end end