; bdiGDB configuration file for the Embedded Planet EP405PC
; ---------------------------------------------------------
;
[INIT]
; init core register
WSPR	954	0x00000000      ;DCWR: Disable data cache write-thru
WSPR	1018	0x00000000	;DCCR: Disable data cache
WSPR	1019	0x00000000	;ICCR: Disable instruction cache
WSPR	981	0x00000000	;EVPR: Exception Vector Table @0x00000000

; Setup SDRAM Controller
WDCR	16	0x00000080	;Select SDRAM0_TR
WDCR	17	0x010E8016	;TR: SDRAM Timing Register
WDCR	16	0x00000040	;Select SDRAM0_B0CR
WDCR	17	0x00084001	;Select bank 0
WDCR	16	0x00000030	;Select SDRAM0_RTR
WDCR	17	0x08080000	;RTR: Refresh Timing Register
WDCR	16	0x00000094	;Select SDRAM0_ECCCFG
WDCR	17	0x00000000	;ECC: Disabled
WDCR	16	0x00000034	;Select SDRAM0_PMIT
WDCR	17	0x0F000000	;PMIT: Power Management Idle Timer
DELAY	1			;Wait for SDRAM powerup
WDCR	16	0x00000020	;Select SDRAM0_CFG
WDCR	17	0x80C00000	;CFG: Enable

; MMU
WM32	0xf0	0x00000000	;invalidate page table base

; EBC
WDCR	0x12	0x00000004	;Select EBC0_B4CR
WDCR	0x13	0xF4058000	;Set NVRTC/BCSR
WDCR	0x12	0x00000014	;Select EBC0_B4AP
WDCR	0x13	0x04050000	;Set NVRTC/BCSR timing
WM8	0xF4000003    0x20	;Enable UART0
WM8	0xF4000009    0x07	;LED
DELAY 500
WM8	0xF4000009    0x0b	;LED
DELAY 500
WM8	0xF4000009    0x0d	;LED
DELAY 500
WM8	0xF4000009    0x0e	;LED
DELAY 500

[TARGET]
JTAGCLOCK   0                   ;use 16 MHz JTAG clock
CPUTYPE     405 		;the used target CPU type
BDIMODE     AGENT   	        ;the BDI working mode (LOADONLY | AGENT)
;WAKEUP      3000                ;wakeup time after reset
BREAKMODE   HARD      	        ;SOFT or HARD, HARD uses PPC hardware breakpoint
STEPMODE    JTAG                ;JTAG or HWBP, HWPB uses one or two hardware breakpoints
VECTOR      CATCH               ;catch unhandled exceptions
MMU         XLAT 0xC0000000     ;enable virtual address mode
PTBASE      0x000000f0          ;address where kernel/user stores pointer to page table
SIO         2002 9600              ;TCP port for serial IO
;SIO         2002 115200              ;TCP port for serial IO

;REGLIST     SPR                 ;select register to transfer to GDB
;REGLIST     ALL                 ;select register to transfer to GDB
;SCANPRED    2 2                 ;JTAG devices connected before PPC400
;SCANSUCC    3 3                 ;JTAG devices connected after PPC400

[HOST]
IP          10.0.1.2
FORMAT      ELF
FILE        linuxbios.elf
;START       0x200000
LOAD        MANUAL              ;load code MANUAL or AUTO after reset
DEBUGPORT   2001
DUMP        dump.bin            ;Linux: dump.bin must already exist and public writable

[FLASH]
WORKSPACE   0x00004000  ;workspace in target RAM for fast programming algorithm
CHIPTYPE    AM29BX16       ;Flash type (AM29F | AM29BX8 | AM29BX16 | I28BX8 | I28BX16)
CHIPSIZE    0x400000    ;The size of one flash chip in bytes (e.g. AM29F040 = 0x80000)
BUSWIDTH    16          ;The width of the flash memory bus in bits (8 | 16 | 32)
ERASE       0xFFF80000  ;erase sector 0 of flash in U7 (AM29F040)
ERASE       0xFFF90000  ;erase sector 1 of flash
ERASE       0xFFFA0000  ;erase sector 2 of flash
ERASE       0xFFFB0000  ;erase sector 3 of flash
ERASE       0xFFFC0000  ;erase sector 4 of flash
ERASE       0xFFFD0000  ;erase sector 5 of flash
ERASE       0xFFFE0000  ;erase sector 6 of flash
ERASE       0xFFFF0000  ;erase sector 7 of flash

[REGS]
IDCR1	0x010	0x011	;MEMCFGADR and MEMCFGDATA
IDCR2	0x012	0x013	;EBCCFGADR and EBCCFGDATA
IDCR3	0x014	0x015	;KIAR and KIDR
FILE    reg405gp.def