/* * This file is part of the coreboot project. * * Copyright (C) 2007-2009 coresystems GmbH * Copyright (C) 2011 Sven Schnelle * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; version 2 of * the License. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, * MA 02110-1301 USA */ // __PRE_RAM__ means: use "unsigned" for device, not a struct. #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include void setup_ich7_gpios(void) { printk(BIOS_DEBUG, " GPIOS..."); /* X60 GPIO: * 1: HDD_PRESENCE# * 6: Unknown (Pulled high by R215 to VCC3B) * 7: BDC_PRESENCE# * 8: H8_WAKE# * 9: RTC_BAT_IN# * 10: Unknown (Pulled high by R700 to VCC3M) * 12: H8SCI# * 13: SLICE_ON_3M# * 14: Unknown (Pulled high by R321 to VCC3) * 15: Unknown (Pulled high by R258 to VCC3) * 19: Unknown (Pulled low by R594) * 21: Unknown (Pulled high by R145 to VCC3) * 22: FWH_WP# * 25: MDC_KILL# * 33: HDD_PRESENCE_2# * 35: CLKREQ_SATA# * 36: PLANARID0 * 37: PLANARID1 * 38: PLANARID2 * 39: PLANARID3 * 48: FWH_TBL# */ outl(0x1f40f7e2, DEFAULT_GPIOBASE + 0x00); /* GPIO_USE_SEL */ outl(0xfea8af83, DEFAULT_GPIOBASE + 0x04); /* GP_IO_SEL */ outl(0xfcc06bdf, DEFAULT_GPIOBASE + 0x0c); /* GP_LVL */ /* Output Control Registers */ outl(0x00000000, DEFAULT_GPIOBASE + 0x18); /* GPO_BLINK */ /* Input Control Registers */ outl(0x00002082, DEFAULT_GPIOBASE + 0x2c); /* GPI_INV */ outl(0x000100c0, DEFAULT_GPIOBASE + 0x30); /* GPIO_USE_SEL2 */ outl(0x00000030, DEFAULT_GPIOBASE + 0x34); /* GP_IO_SEL2 */ outl(0x000100c0, DEFAULT_GPIOBASE + 0x38); /* GP_LVL2 */ } static void ich7_enable_lpc(void) { // Enable Serial IRQ pci_write_config8(PCI_DEV(0, 0x1f, 0), 0x64, 0xd0); // I/O Decode Ranges // X60: 0x0210 == 00000010 00010000 // Macbook21: 0x0010 == 00000000 00010000 // Bit 9:8 LPT Decode Range. This field determines which range to // decode for the LPT Port. // 00 = 378h ­ 37Fh and 778h ­ 77Fh // 10 = 3BCh ­ 3BEh and 7BCh ­ 7BEh pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x80, 0x0010); // LPC_EN--LPC I/F Enables Register // X60: 0x1f0d == 00011111 00001101 // Macbook21: 0x3807 == 00111000 00000111 // Bit 13 CNF2_LPC_EN -- R/W. Microcontroller Enable # 2. // 0 = Disable. // 1 = Enables the decoding of the I/O locations 4Eh and 4Fh // to the LPC interface. This range is used for a // microcontroller. // Bit 12 CNF1_LPC_EN -- R/W. Super I/O Enable. // 0 = Disable. // 1 = Enables the decoding of the I/O locations 2Eh and 2Fh // to the LPC interface. This range is used for // Super I/O devices. // Bit 11 MC_LPC_EN -- R/W. Microcontroller Enable # 1. // 0 = Disable. // 1 = Enables the decoding of the I/O locations 62h and 66h // to the LPC interface. This range is used for a // microcontroller. // Bit 10 KBC_LPC_EN -- R/W. Keyboard Enable. // 0 = Disable. // 1 = Enables the decoding of the I/O locations 60h and 64h // to the LPC interface. This range is used for a // microcontroller. // Bit 9 GAMEH_LPC_EN -- R/W. High Gameport Enable // 0 = Disable. // 1 = Enables the decoding of the I/O locations 208h to 20Fh // to the LPC interface. This range is used for a gameport. // Bit 8 GAMEL_LPC_EN -- R/W. Low Gameport Enable // 0 = Disable. // 1 = Enables the decoding of the I/O locations 200h to 207h // to the LPC interface. This range is used for a gameport. // Bit 3 FDD_LPC_EN -- R/W. Floppy Drive Enable // 0 = Disable. // 1 = Enables the decoding of the FDD range to the LPC // interface. This range is selected in the LPC_FDD/LPT // Decode Range Register (D31:F0:80h, bit 12). // Bit 2 LPT_LPC_EN -- R/W. Parallel Port Enable // 0 = Disable. // 1 = Enables the decoding of the LPT range to the LPC // interface. This range is selected in the LPC_FDD/LPT // Decode Range Register (D31:F0:80h, bit 9:8). // Bit 1 COMB_LPC_EN -- R/W. Com Port B Enable // 0 = Disable. // 1 = Enables the decoding of the COMB range to the LPC // interface. This range is selected in the LPC_COM Decode // Range Register (D31:F0:80h, bits 6:4). // Bit 0 COMA_LPC_EN -- R/W. Com Port A Enable // 0 = Disable. // 1 = Enables the decoding of the COMA range to the LPC // interface. This range is selected in the LPC_COM Decode // Range Register (D31:F0:80h, bits 3:2). pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x82, 0x3807); /* GEN1_DEC, LPC Interface Generic Decode Range 1 */ // X60: 0x1601 0x007c == 00000000 01111100 00010110 00000001 // Macbook21: 0x0681 0x000c == 00000000 00001100 00000110 10000001 // Bit 31:24 Reserved. // Bit 23:18 Generic I/O Decode Range Address[7:2] Mask: A `1' in any // bit position indicates that any value in the corresponding // address bit in a received cycle will be treated as a // match. The corresponding bit in the Address field, below, // is ignored. The mask is only provided for the lower 6 bits // of the DWord address, allowing for decoding blocks up to // 256 bytes in size. // Bit 17:16 Reserved. // Bit 15:2 Generic I/O Decode Range 1 Base Address (GEN1_BASE). This // address is aligned on a 128-byte boundary, and must have // address lines 31:16 as 0. NOTE: The Intel ICH7 does not // provide decode down to the word or byte level. // Bit 1 Reserved. // Bit 0 Generic Decode Range 1 Enable (GEN1_EN) -- R/W. // 0 = Disable. // 1 = Enable the GEN1 I/O range to be forwarded to the LPC // I/F pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x84, 0x0681); pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x86, 0x000c); /* GEN2_DEC, LPC Interface Generic Decode Range 2 */ // X60: 0x15e1 0x000c == 00000000 00001100 00010101 11100001 // Macbook21: 0x1641 0x000c == 00000000 00001100 00010110 01000001 pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x88, 0x1641); pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x8a, 0x000c); /* GEN3_DEC, LPC Interface Generic Decode Range 3 */ // X60: 0x1681 0x001c == 00000000 00011100 00010110 10000001 // Macbook21: 0x0000 0x0000 pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x8c, 0x0000); // obsolete, because it writes zeros? pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x8e, 0x0000); /* GEN4_DEC, LPC Interface Generic Decode Range 4 */ // X60: 0x0000 0x0000 // Macbook21: 0x0301 0x001c == 00000000 00011100 00000011 00000001 pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x90, 0x0301); pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x92, 0x001c); } static void rcba_config(void) { /* V0CTL Virtual Channel 0 Resource Control */ RCBA32(0x0014) = 0x80000001; /* V1CAP Virtual Channel 1 Resource Capability */ RCBA32(0x001c) = 0x03128010; /* Device 1f interrupt pin register */ RCBA32(0x3100) = 0x00042210; RCBA32(0x3108) = 0x10004321; /* PCIe Interrupts */ RCBA32(0x310c) = 0x00214321; /* HD Audio Interrupt */ RCBA32(0x3110) = 0x00000001; /* dev irq route register */ RCBA16(0x3140) = 0x0232; RCBA16(0x3142) = 0x3246; RCBA16(0x3144) = 0x0235; RCBA16(0x3146) = 0x3201; RCBA16(0x3148) = 0x3216; /* Enable IOAPIC */ RCBA8(0x31ff) = 0x03; /* Disable unused devices */ RCBA32(0x3418) = FD_PCIE6 | FD_PCIE5 | FD_PCIE4 | FD_PCIE3 | FD_INTLAN | FD_ACMOD | FD_ACAUD; RCBA32(0x3418) |= (1 << 0); // Required. /* Set up I/O Trap #0 for 0xfe00 (SMIC) */ // RCBA32(0x1e84) = 0x00020001; // RCBA32(0x1e80) = 0x0000fe01; /* Set up I/O Trap #3 for 0x800-0x80c (Trap) */ RCBA32(0x1e9c) = 0x000200f0; RCBA32(0x1e98) = 0x000c0801; } static void early_ich7_init(void) { uint8_t reg8; uint32_t reg32; // program secondary mlt XXX byte? pci_write_config8(PCI_DEV(0, 0x1e, 0), 0x1b, 0x20); // reset rtc power status reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xa4); reg8 &= ~(1 << 2); pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xa4, reg8); // usb transient disconnect reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xad); reg8 |= (3 << 0); pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xad, reg8); reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xfc); reg32 |= (1 << 29) | (1 << 17); pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xfc, reg32); reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xdc); reg32 |= (1 << 31) | (1 << 27); pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xdc, reg32); RCBA32(0x0088) = 0x0011d000; RCBA16(0x01fc) = 0x060f; RCBA32(0x01f4) = 0x86000040; RCBA32(0x0214) = 0x10030549; RCBA32(0x0218) = 0x00020504; RCBA8(0x0220) = 0xc5; reg32 = RCBA32(0x3410); reg32 |= (1 << 6); RCBA32(0x3410) = reg32; reg32 = RCBA32(0x3430); reg32 &= ~(3 << 0); reg32 |= (1 << 0); RCBA32(0x3430) = reg32; RCBA32(0x3418) |= (1 << 0); RCBA16(0x0200) = 0x2008; RCBA8(0x2027) = 0x0d; RCBA16(0x3e08) |= (1 << 7); RCBA16(0x3e48) |= (1 << 7); RCBA32(0x3e0e) |= (1 << 7); RCBA32(0x3e4e) |= (1 << 7); // next step only on ich7m b0 and later: reg32 = RCBA32(0x2034); reg32 &= ~(0x0f << 16); reg32 |= (5 << 16); RCBA32(0x2034) = reg32; } void main(unsigned long bist) { int s3resume = 0; const u8 spd_addrmap[2 * DIMM_SOCKETS] = { 0x50, 0x51, 0x52, 0x53 }; timestamp_init(get_initial_timestamp()); timestamp_add_now(TS_START_ROMSTAGE); if (bist == 0) enable_lapic(); /* Force PCIRST# */ pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, SBR); udelay(200 * 1000); pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, 0); ich7_enable_lpc(); /* Set up the console */ console_init(); /* Halt if there was a built in self test failure */ report_bist_failure(bist); if (MCHBAR16(SSKPD) == 0xCAFE) { printk(BIOS_DEBUG, "Soft reset detected, rebooting properly.\n"); outb(0x6, 0xcf9); halt(); } /* Perform some early chipset initialization required * before RAM initialization can work */ i945_early_initialization(); s3resume = southbridge_detect_s3_resume(); /* Enable SPD ROMs and DDR-II DRAM */ enable_smbus(); #if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8 dump_spd_registers(); #endif timestamp_add_now(TS_BEFORE_INITRAM); sdram_initialize(s3resume ? 2 : 0, spd_addrmap); timestamp_add_now(TS_AFTER_INITRAM); /* Perform some initialization that must run before stage2 */ early_ich7_init(); /* This should probably go away. Until now it is required * and mainboard specific */ rcba_config(); /* Chipset Errata! */ fixup_i945_errata(); /* Initialize the internal PCIe links before we go into stage2 */ i945_late_initialization(s3resume); timestamp_add_now(TS_END_ROMSTAGE); }