# SPDX-License-Identifier: GPL-2.0-only

# TODO: Update for birman

chip soc/amd/phoenix
	register "common_config.espi_config" = "{
		.std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN | ESPI_DECODE_IO_0X2E_0X2F_EN | ESPI_DECODE_IO_0X60_0X64_EN,
		.generic_io_range[0] = {
			.base = 0x3f8,
			.size = 8,
		},
		.generic_io_range[1] = {
			.base = 0x600,
			.size = 256,
		},
		.io_mode = ESPI_IO_MODE_QUAD,
		.op_freq_mhz = ESPI_OP_FREQ_16_MHZ,
		.crc_check_enable = 1,
		.alert_pin = ESPI_ALERT_PIN_PUSH_PULL,
		.periph_ch_en = 1,
		.vw_ch_en = 1,
		.oob_ch_en = 1,
		.flash_ch_en = 0,
	}"

	register "i2c_scl_reset" = "GPIO_I2C0_SCL | GPIO_I2C1_SCL |
					GPIO_I2C2_SCL | GPIO_I2C3_SCL"

	register "i2c[0].early_init" = "1"
	register "i2c[1].early_init" = "1"
	register "i2c[2].early_init" = "1"
	register "i2c[3].early_init" = "1"

	# I2C Pad Control RX Select Configuration
	register "i2c_pad[0].rx_level" = "I2C_PAD_RX_1_8V"
	register "i2c_pad[1].rx_level" = "I2C_PAD_RX_1_8V"
	register "i2c_pad[2].rx_level" = "I2C_PAD_RX_1_8V"
	register "i2c_pad[3].rx_level" = "I2C_PAD_RX_1_8V"

	register "s0ix_enable" = "true"

	register "pspp_policy" = "DXIO_PSPP_DISABLED" # TODO: reenable when PSPP works

	register "usb_phy_custom" = "1"
	register "usb_phy" = "{
		.Usb2PhyPort[0] = {
			.compdistune = 0x1,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[1] = {
			.compdistune = 0x1,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[2] = {
			.compdistune = 0x1,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[3] = {
			.compdistune = 0x1,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[4] = {
			.compdistune = 0x1,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[5] = {
			.compdistune = 0x1,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[6] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x6,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[7] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xc,
			.sqrxtune = 0x2,
			.txfslstune = 0x1,
			.txpreempamptune = 0x3,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x6,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb3PhyPort[0] = {
			.tx_term_ctrl = 0x2,
			.rx_term_ctrl = 0x2,
			.tx_vboost_lvl_en = 0x0,
			.tx_vboost_lvl = 0x5,
		},
		.Usb3PhyPort[1] = {
			.tx_term_ctrl = 0x2,
			.rx_term_ctrl = 0x2,
			.tx_vboost_lvl_en = 0x0,
			.tx_vboost_lvl = 0x5,
		},
		.Usb3PhyPort[2] = {
			.tx_term_ctrl = 0x2,
			.rx_term_ctrl = 0x2,
			.tx_vboost_lvl_en = 0x0,
			.tx_vboost_lvl = 0x5,
		},
		.ComboPhyStaticConfig[0] = USB_COMBO_PHY_MODE_USB_C,
		.ComboPhyStaticConfig[1] = USB_COMBO_PHY_MODE_USB_C,
		.ComboPhyStaticConfig[2] = USB_COMBO_PHY_MODE_USB_C,
		.BatteryChargerEnable = 0,
		.PhyP3CpmP4Support = 0,
	}"

	register "gpp_clk_config[0]" = "GPP_CLK_REQ" # MXM
	register "gpp_clk_config[1]" = "GPP_CLK_REQ" # NVMe SSD1
	register "gpp_clk_config[2]" = "GPP_CLK_REQ" # NVMe SSD0
	register "gpp_clk_config[3]" = "GPP_CLK_REQ" # WLAN
	register "gpp_clk_config[4]" = "GPP_CLK_REQ" # WWAN
	register "gpp_clk_config[5]" = "GPP_CLK_REQ" # SD
	register "gpp_clk_config[6]" = "GPP_CLK_REQ" # GBE

	device domain 0 on
		device ref iommu on end
		device ref gpp_bridge_1_1 on end # MXM
		device ref gpp_bridge_1_2 on
			# Required so the NVMe gets placed into D3 when entering S0i3.
			chip drivers/pcie/rtd3/device
				register "name" = ""NVME""
				device pci 00.0 on end
			end
		end # NVMe SSD1
		device ref gpp_bridge_1_3 on end # GBE
		device ref gpp_bridge_2_1 on end # SD
		device ref gpp_bridge_2_2 on end # WWAN
		device ref gpp_bridge_2_3 on end # WIFI
		device ref gpp_bridge_2_4 on
			# Required so the NVMe gets placed into D3 when entering S0i3.
			chip drivers/pcie/rtd3/device
				register "name" = ""NVME""
				device pci 00.0 on end
			end
		end # NVMe SSD0
		device ref gpp_bridge_a on  # Internal GPP Bridge 0 to Bus A
			device ref gfx on end # Internal GPU (GFX)
			device ref gfx_hda on end # Display HD Audio Controller (GFXAZ)
			device ref crypto on end # Crypto Coprocessor
			device ref xhci_0 on # USB 3.1 (USB0)
				chip drivers/usb/acpi
					device ref xhci_0_root_hub on
						chip drivers/usb/acpi
							device ref usb3_port2 on end
						end
						chip drivers/usb/acpi
							device ref usb3_port3 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port2 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port3 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port4 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port5 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port6 on end
						end
					end
				end
			end
			device ref xhci_1 on # USB 3.1 (USB1)
				chip drivers/usb/acpi
					device ref xhci_1_root_hub on
						chip drivers/usb/acpi
							device ref usb3_port7 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port7 on end
						end
					end
				end
			end
			device ref acp on end # Audio Processor (ACP)
		end
		device ref gpp_bridge_c on  # Internal GPP Bridge 2 to Bus C
			device ref usb4_xhci_0 on
				chip drivers/usb/acpi
					device ref usb4_xhci_0_root_hub on
						chip drivers/usb/acpi
							device ref usb3_port0 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port0 on end
						end
					end
				end
			end
			device ref usb4_xhci_1 on
				chip drivers/usb/acpi
					device ref usb4_xhci_1_root_hub on
						chip drivers/usb/acpi
							device ref usb3_port1 on end
						end
						chip drivers/usb/acpi
							device ref usb2_port1 on end
						end
					end
				end
			end
		end
	end

	device ref i2c_0 on end
	device ref i2c_1 on end
	device ref i2c_2 on end
	device ref i2c_3 on end
	device ref uart_0 on end # UART0

end