# SPDX-License-Identifier: GPL-2.0-only

if BOARD_AMD_BILBY

config BOARD_SPECIFIC_OPTIONS
	def_bool y
	select SOC_AMD_PICASSO
	select BOARD_ROMSIZE_KB_16384
	select AZALIA_HDA_CODEC_SUPPORT
	select HAVE_ACPI_RESUME
	select DRIVERS_UART_ACPI
	select AMD_SOC_CONSOLE_UART if !AMD_LPC_DEBUG_CARD

config FMDFILE
	default "src/mainboard/amd/bilby/board.fmd"

config AMD_LPC_DEBUG_CARD
	bool "Enable LPC-Serial debug card on the debug header"
	default n
	select BILBY_LPC
	select SUPERIO_SMSC_SIO1036
	help
	  AMD's debug card contains an SMSC SIO1036 device which provides an
	  I/O-mapped UART in the system. This is mutually exclusive with
	  AMD_SOC_CONSOLE_UART which selects the SoC's integrated memory-mapped
	  UART for coreboot console output.

choice
	prompt "SMSC/Microchip 1036 SuperIO config address"
	depends on SUPERIO_SMSC_SIO1036
	default BILBY_SMSC_SIO1036_BASE_164E

config BILBY_SMSC_SIO1036_BASE_4E
	bool "0x4e/0x4d base address"

config BILBY_SMSC_SIO1036_BASE_164E
	bool "0x164e/0x164d base address"

endchoice

config SUPERIO_ADDR_BASE
	hex
	default 0x4e	if BILBY_SMSC_SIO1036_BASE_4E
	default 0x164e	if BILBY_SMSC_SIO1036_BASE_164E

config CBFS_SIZE
	default 0xfef000 # Maximum size for the Bilby FMAP

config MAINBOARD_DIR
	default "amd/bilby"

config MAINBOARD_PART_NUMBER
	default "BILBY"

config ONBOARD_VGA_IS_PRIMARY
	bool
	default y

if !AMD_LPC_DEBUG_CARD
choice
	prompt "State of IOMux for LPC/eMMC signals"
	default BILBY_IOMUX_USE_EMMC
	help
	  Bilby is designed to use either LPC or eMMC signals.  Use this
	  selection to determine which are configured for this image.

config BILBY_IOMUX_USE_LPC
	bool "LPC signals"

config BILBY_IOMUX_USE_EMMC
	bool "eMMC signals"

endchoice
endif # !AMD_LPC_DEBUG_CARD

config BILBY_LPC
	bool
	default y if BILBY_IOMUX_USE_LPC
	help
	  Picasso's LPC bus signals are MUXed with some of the EMMC signals.
	  Select this option if LPC signals are required.

if !EM100	# EM100 defaults in soc/amd/common/blocks/spi/Kconfig
config EFS_SPI_READ_MODE
	default 3	# Quad IO (1-1-4)

config EFS_SPI_SPEED
	default 0	# 66MHz

config EFS_SPI_MICRON_FLAG
	default 0

config NORMAL_READ_SPI_SPEED
	default 1	# 33MHz

config ALT_SPI_SPEED
	default 1	# 33MHz

config TPM_SPI_SPEED
	default 1	# 33MHz

endif # !EM100

choice
	prompt "DDI-0 connector type"
	default CONNECT_DP_ON_DDI_0

config CONNECT_HDMI_ON_DDI_0
	bool "Use HDMI interface"

config CONNECT_DP_ON_DDI_0
	bool "Use Displayport interface"
endchoice

config DDI0_CONNECTOR_TYPE
	int
	default 0 if CONNECT_DP_ON_DDI_0
	default 4 if CONNECT_HDMI_ON_DDI_0

choice
	prompt "DDI-1 connector type"
	default CONNECT_DP_ON_DDI_1

config CONNECT_HDMI_ON_DDI_1
	bool "Use HDMI interface"

config CONNECT_DP_ON_DDI_1
	bool "Use Displayport interface"
endchoice

config DDI1_CONNECTOR_TYPE
	int
	default 0 if CONNECT_DP_ON_DDI_1
	default 4 if CONNECT_HDMI_ON_DDI_1

endif # BOARD_AMD_BILBY