From 6c4861859761e1110e9651b989a521152394fcf3 Mon Sep 17 00:00:00 2001 From: Paul Menzel Date: Sun, 11 Mar 2018 13:26:35 +0100 Subject: util/autoport: Improve `readme.me` Correct spelling mistakes and punctuation, and improve some wording. Change-Id: I2c976bd62d8fa508373747b3fb3cf31490d5f631 Signed-off-by: Paul Menzel Reviewed-on: https://review.coreboot.org/25338 Tested-by: build bot (Jenkins) Reviewed-by: Felix Held --- util/autoport/readme.md | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-) (limited to 'util/autoport') diff --git a/util/autoport/readme.md b/util/autoport/readme.md index 3b7c2e386d..21174b03c9 100644 --- a/util/autoport/readme.md +++ b/util/autoport/readme.md @@ -3,19 +3,19 @@ ## Supported platforms ### Chipset -For any sandybridge or ivybridge platform generated result should +For any Sandy Bridge or Ivy Bridge platform the generated result should be bootable, possibly with minor fixes. ### EC -EC support is likely to work on intel-based thinkpads. Other laptops are -likely to miss EC support +EC support is likely to work on Intel-based thinkpads. Other laptops are +likely to miss EC support. ## How to use -* Go into BIOS setup on target machine and enable all the devices. -This will allow autoport to detect as much as possible +* Go into BIOS setup on the target machine and enable all devices. +This will allow autoport to detect as much as possible. * Boot into target machine under GNU/Linux -* Make sure that following components are installed: +* Make sure that the following components are installed: * GCC * golang * lspci @@ -35,7 +35,7 @@ This will allow autoport to detect as much as possible sudo ./autoport --input_log=logs --make_logs --coreboot_dir=../.. Note: in case you have problems getting gcc and golang to target machine - you can just compile on another machine and transfer binaries + you can just compile on another machine and transfer the binaries `autoport`, `inteltool` and `ectool`. You'll still need other prerequisites but you may place them in the same directory as autoport. @@ -48,21 +48,21 @@ then you may want to add relevant PCIIDs to autoport. When rerunning you can skip argument `--make_logs` to reuse the same logs * At this point the new board is added to the tree but don't flash it -yet as it will brick you machine. Instead keep this new port and logs -from `util/autoport/logs` somewhere safe +yet as it will brick your machine. Instead keep this new port and the logs +from `util/autoport/logs` somewhere safe. * Disassemble your laptop and locate flash chip -is a great resource. Flash chip is usually in `SOIC-8` (2x4 pins) or `SOIC-16` +is a great resource. The flash chip is usually in `SOIC-8` (2x4 pins) or `SOIC-16` (2x8 chips). You'll probably have several candidates. Look up what's written on them and look up what's this chip on the web. -* Once you know what's the chip is, get external flasher and read it. Twice. Compare +* Once you know what's the chip is, get an external flasher and read it. Twice. Compare the results and retry if they differ. Save the result somewhere safe, in preference -copy to read-only storage as backup. +copy it to read-only storage as backup. * Compile coreboot with console enabled (EHCI debug or serial if present are recommended) -* For recent intel chipsets you need to avoid overwriting ME firmware. Recommended procedure is +* For recent Intel chipsets you need to avoid overwriting ME firmware. Recommended procedure is (replace 8 with your flash size in MiB): cp backup.rom flash.rom @@ -113,7 +113,7 @@ up in SPD. Under Linux you can see present SPD addresses with following commands 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -- -Make sure to replace `9` with whatever bus is marked as smbus. Here in an example +Make sure to replace `9` with whatever bus is marked as SMBus. Here in an example you see SPD at address `0x50`. Since we've booted with just the module in C0S0, so the first entry in SPD map has to be `0x50`. Once you have SPD map your `mainboard_get_spd` should look something like: @@ -129,7 +129,7 @@ You can and should omit lines which correspond to slots not present on your machine. Note: slot labelling may be missing or unreliable. Use `inteltool` to see -which slot have modules in them. +which slots have modules in them. This way works well if your RAM is socketed. For soldered RAM if you see its SPD, you're in luck and can proceed the same way although you may have to -- cgit v1.2.3