From a427ff0f500b16e3a073cff6af66d9c3a562caf4 Mon Sep 17 00:00:00 2001 From: Subrata Banik Date: Wed, 31 Oct 2018 15:05:35 +0530 Subject: vendorcode/intel/../icelake: Update ICL FSP header BIOS version 3092 After building from here : https://chrome-internal.googlesource.com/chromeos/third_party/intel-fsp/icl/+/refs/tags/upstream/BIOS_Version_3092 Change-Id: I8924dbf4a8d6a303540ced1c9c48586d26d6beaa Signed-off-by: Aamir Bohra Signed-off-by: Subrata Banik Reviewed-on: https://review.coreboot.org/c/coreboot/+/31954 Tested-by: build bot (Jenkins) Reviewed-by: Wonkyu Kim --- src/vendorcode/intel/fsp/fsp2_0/icelake/FspsUpd.h | 3553 ++++++++++++++++++++- 1 file changed, 3545 insertions(+), 8 deletions(-) (limited to 'src/vendorcode/intel/fsp/fsp2_0/icelake/FspsUpd.h') diff --git a/src/vendorcode/intel/fsp/fsp2_0/icelake/FspsUpd.h b/src/vendorcode/intel/fsp/fsp2_0/icelake/FspsUpd.h index 37356a142a..4aa5008356 100644 --- a/src/vendorcode/intel/fsp/fsp2_0/icelake/FspsUpd.h +++ b/src/vendorcode/intel/fsp/fsp2_0/icelake/FspsUpd.h @@ -1,6 +1,6 @@ /** @file -Copyright (c) 2018, Intel Corporation. All rights reserved.
+Copyright (c) 2019, Intel Corporation. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: @@ -37,15 +37,3552 @@ are permitted provided that the following conditions are met: #pragma pack(1) + +/// +/// Azalia Header structure +/// +typedef struct { + UINT16 VendorId; ///< Codec Vendor ID + UINT16 DeviceId; ///< Codec Device ID + UINT8 RevisionId; ///< Revision ID of the codec. 0xFF matches any revision. + UINT8 SdiNum; ///< SDI number, 0xFF matches any SDI. + UINT16 DataDwords; ///< Number of data DWORDs pointed by the codec data buffer. + UINT32 Reserved; ///< Reserved for future use. Must be set to 0. +} AZALIA_HEADER; + +/// +/// Audio Azalia Verb Table structure +/// +typedef struct { + AZALIA_HEADER Header; ///< AZALIA PCH header + UINT32 *Data; ///< Pointer to the data buffer. Its length is specified in the header +} AUDIO_AZALIA_VERB_TABLE; + +/// +/// Refer to the definition of PCH_INT_PIN +/// +typedef enum { + SiPchNoInt, ///< No Interrupt Pin + SiPchIntA, + SiPchIntB, + SiPchIntC, + SiPchIntD +} SI_PCH_INT_PIN; +/// +/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device. +/// +typedef struct { + UINT8 Device; ///< Device number + UINT8 Function; ///< Device function + UINT8 IntX; ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN) + UINT8 Irq; ///< IRQ to be set for device. +} SI_PCH_DEVICE_INTERRUPT_CONFIG; + +#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG 64 ///< Number of all PCH devices + + /** Fsp S Configuration **/ typedef struct { -} FSP_S_CONFIG; -/** Fsp S Test Configuration +/** Offset 0x0020 - Si Config CSM Flag. + Platform specific common policies that used by several silicon components. CSM status flag. + $EN_DIS **/ -typedef struct { -} FSP_S_TEST_CONFIG; + UINT8 SiCsmFlag; + +/** Offset 0x0021 +**/ + UINT8 UnusedUpdSpace0[3]; + +/** Offset 0x0024 - SVID SDID table Poniter. + The address of the table of SVID SDID to customize each SVID SDID entry. +**/ + UINT32 SiSsidTablePtr; + +/** Offset 0x0028 - Number of ssid table. + SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr. +**/ + UINT16 SiNumberOfSsidTableEntry; + +/** Offset 0x002A +**/ + UINT8 SiPostMemRsvd[16]; + +/** Offset 0x003A +**/ + UINT8 UnusedUpdSpace1[2]; + +/** Offset 0x003C - MicrocodeRegionBase + Memory Base of Microcode Updates +**/ + UINT32 MicrocodeRegionBase; + +/** Offset 0x0040 - MicrocodeRegionSize + Size of Microcode Updates +**/ + UINT32 MicrocodeRegionSize; + +/** Offset 0x0044 - Enable or Disable TXT + Enable or Disable TXT; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 TxtEnable; + +/** Offset 0x0045 - Advanced Encryption Standard (AES) feature + Enable or Disable Advanced Encryption Standard (AES) feature; 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 AesEnable; + +/** Offset 0x0046 - Deprecated Skip Multi-Processor Initialization + {@deprecated SkipMpInit has been moved to FspmUpd as SkipMpInitPreMem. 0: Initialize; + 1: Skip + $EN_DIS +**/ + UINT8 SkipMpInit; + +/** Offset 0x0047 - PpinSupport to view Protected Processor Inventory Number + Enable or Disable or Auto (Based on End of Manufacturing flag. Disabled if this + flag is set) for PPIN Support + 0: Disable, 1: Enable, 2: Auto +**/ + UINT8 PpinSupport; + +/** Offset 0x0048 - Turbo Mode + Enable/Disable Turbo mode. 0: disable, 1: enable + $EN_DIS +**/ + UINT8 TurboMode; + +/** Offset 0x0049 - Power State 3 enable/disable + PCODE MMIO Mailbox: Power State 3 enable/disable; 0: Disable; 1: Enable. + For all VR Indexes +**/ + UINT8 Psi3Enable; + +/** Offset 0x004A - Power State 4 enable/disable + PCODE MMIO Mailbox: Power State 4 enable/disable; 0: Disable; 1: Enable.For + all VR Indexes +**/ + UINT8 Psi4Enable; + +/** Offset 0x004B +**/ + UINT8 UnusedUpdSpace2; + +/** Offset 0x004C - Imon slope correction + PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values. + Range is 0-200. 125 = 1.25. 0: Auto.For all VR Indexes +**/ + UINT16 ImonSlope; + +/** Offset 0x004E - Imon offset correction + PCODE MMIO Mailbox: Imon offset correction. Value is a 2's complement signed integer. + Units 1/1000, Range 0-63999. For an offset = 12.580, use 12580. 0: Auto +**/ + UINT16 ImonOffset; + +/** Offset 0x0050 - Enable/Disable BIOS configuration of VR + Enable/Disable BIOS configuration of VR; 0: Disable; 1: Enable.For all VR Indexes +**/ + UINT8 VrConfigEnable; + +/** Offset 0x0051 - Thermal Design Current enable/disable + PCODE MMIO Mailbox: Thermal Design Current enable/disable; 0: Disable; 1: + Enable.For all VR Indexes +**/ + UINT8 TdcEnable; + +/** Offset 0x0052 - HECI3 state + PCODE MMIO Mailbox: Thermal Design Current time window. Defined in milli seconds. + Valid Values 1 - 1ms , 2 - 2ms , 3 - 3ms , 4 - 4ms , 5 - 5ms , 6 - 6ms , 7 - 7ms + , 8 - 8ms , 10 - 10ms.For all VR Indexe +**/ + UINT8 TdcTimeWindow; + +/** Offset 0x0053 - Thermal Design Current Lock + PCODE MMIO Mailbox: Thermal Design Current Lock; 0: Disable; 1: Enable.For + all VR Indexes +**/ + UINT8 TdcLock; + +/** Offset 0x0054 - Thermal Design Current current limit + PCODE MMIO Mailbox: Thermal Design Current current limit. Specified in 1/8A units. + Range is 0-4095. 1000 = 125A. 0: Auto. For all VR Indexes +**/ + UINT16 TdcPowerLimit; + +/** Offset 0x0056 - AcLoadline + PCODE MMIO Mailbox: AcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is + 0-6249. Intel Recommended Defaults vary by domain and SKU. +**/ + UINT16 AcLoadline; + +/** Offset 0x0058 - DcLoadline + PCODE MMIO Mailbox: DcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is + 0-6249.Intel Recommended Defaults vary by domain and SKU. +**/ + UINT16 DcLoadline; + +/** Offset 0x005A - Power State 1 Threshold current + PCODE MMIO Mailbox: Power State 1 current cuttof in 1/4 Amp increments. Range is 0-128A. +**/ + UINT16 Psi1Threshold; + +/** Offset 0x005C - Power State 2 Threshold current + PCODE MMIO Mailbox: Power State 2 current cuttof in 1/4 Amp increments. Range is 0-128A. +**/ + UINT16 Psi2Threshold; + +/** Offset 0x005E - Power State 3 Threshold current + PCODE MMIO Mailbox: Power State 3 current cuttof in 1/4 Amp increments. Range is 0-128A. +**/ + UINT16 Psi3Threshold; + +/** Offset 0x0060 - Icc Max limit + PCODE MMIO Mailbox: VR Icc Max limit. 0-255A in 1/4 A units. 400 = 100A +**/ + UINT16 IccMax; + +/** Offset 0x0062 - VR Voltage Limit + PCODE MMIO Mailbox: VR Voltage Limit. Range is 0-7999mV. +**/ + UINT16 VrVoltageLimit; + +/** Offset 0x0064 - Platform Psys slope correction + PCODE MMIO Mailbox: Platform Psys slope correction. 0 - Auto Specified in + 1/100 increment values. Range is 0-200. 125 = 1.25 +**/ + UINT8 PsysSlope; + +/** Offset 0x0065 - Platform Psys offset correction + PCODE MMIO Mailbox: Platform Psys offset correction. 0 - Auto Units 1/4, + Range 0-255. Value of 100 = 100/4 = 25 offset +**/ + UINT8 PsysOffset; + +/** Offset 0x0066 - Acoustic Noise Mitigation feature + Enable or Disable Acoustic Noise Mitigation feature. This has to be enabled to program + slew rate configuration for all VR domains, Pre Wake, Ramp Up and, Ramp Down times.0: + Disabled; 1: Enabled + $EN_DIS +**/ + UINT8 AcousticNoiseMitigation; + +/** Offset 0x0067 - Pre Wake Randomization time + PCODE MMIO Mailbox: Acoustic Mitigation Range.Defines the maximum pre-wake randomization + time in micro ticks.This can be programmed only if AcousticNoiseMitigation is enabled. + Range 0-255 0. +**/ + UINT8 PreWake; + +/** Offset 0x0068 - Ramp Up Randomization time + PCODE MMIO Mailbox: Acoustic Mitigation Range.Defines the maximum Ramp Up randomization + time in micro ticks.This can be programmed only if AcousticNoiseMitigation is enabled.Range + 0-255 0. +**/ + UINT8 RampUp; + +/** Offset 0x0069 - Ramp Down Randomization time + PCODE MMIO Mailbox: Acoustic Mitigation Range.Defines the maximum Ramp Down randomization + time in micro ticks.This can be programmed only if AcousticNoiseMitigation is enabled.Range + 0-255 0. +**/ + UINT8 RampDown; + +/** Offset 0x006A - Disable Fast Slew Rate for Deep Package C States for VR FIVR domain + Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation + feature enabled. 0: False; 1: True + $EN_DIS +**/ + UINT8 FastPkgCRampDisableFivr; + +/** Offset 0x006B - Slew Rate configuration for Deep Package C States for VR FIVR domain + Slew Rate configuration for Deep Package C States for VR FIVR domain based on Acoustic + Noise Mitigation feature enabled. 0: Fast/2; 1: Fast/4; 2: Fast/8; 3: Fast/16 + 0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16 +**/ + UINT8 SlowSlewRateForFivr; + +/** Offset 0x006C - Enable VR specific mailbox command + VR specific mailbox commands. 00b - no VR specific command sent. 01b - A + VR mailbox command specifically for the MPS IMPV8 VR will be sent. 10b - VR specific + command sent for PS4 exit issue. 11b - Reserved. + $EN_DIS +**/ + UINT8 SendVrMbxCmd; + +/** Offset 0x006D +**/ + UINT8 UnusedUpdSpace3; + +/** Offset 0x006E - FIVR RFI Frequency + PCODE MMIO Mailbox: Set the desired RFI frequency, in increments of 100KHz. 0: + Auto. Range varies based on XTAL clock: 0-1918 (Up to 191.8HMz) for 24MHz clock; + 0-1535 (Up to 153.5MHz) for 19MHz clock. +**/ + UINT16 FivrRfiFrequency; + +/** Offset 0x0070 - FIVR RFI Spread Spectrum + PCODE MMIO Mailbox: FIVR RFI Spread Spectrum, in 0.1% increments, with range of + 0.2% to 10%. 2: 0.2%; Range: 0.2% to 10.0% (2-100). +**/ + UINT8 FivrSpreadSpectrum; + +/** Offset 0x0071 - Enable or Disable Minimum Voltage Override + Enable or disable Minimum Voltage overrides ; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 EnableMinVoltageOverride; + +/** Offset 0x0072 - Min Voltage for C8 + PCODE MMIO Mailbox: Minimum voltage for C8. Valid if EnableMinVoltageOverride = + 1. Range 0 to 1999mV. 0: 0mV +**/ + UINT16 MinVoltageC8; + +/** Offset 0x0074 - Min Voltage for Runtime + PCODE MMIO Mailbox: Minimum voltage for runtime. Valid if EnableMinVoltageOverride + = 1. Range 0 to 1999mV. 0: 0mV +**/ + UINT16 MinVoltageRuntime; + +/** Offset 0x0076 - Enable or Disable MLC Streamer Prefetcher + Enable or Disable MLC Streamer Prefetcher; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 MlcStreamerPrefetcher; + +/** Offset 0x0077 - Enable or Disable MLC Spatial Prefetcher + Enable or Disable MLC Spatial Prefetcher; 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 MlcSpatialPrefetcher; + +/** Offset 0x0078 - Enable or Disable Monitor /MWAIT instructions + Enable or Disable Monitor /MWAIT instructions; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 MonitorMwaitEnable; + +/** Offset 0x0079 - Control on Processor Trace output scheme + Control on Processor Trace output scheme; 0: Single Range Output; 1: ToPA Output. + 0: Single Range Output, 1: ToPA Output +**/ + UINT8 ProcessorTraceOutputScheme; + +/** Offset 0x007A - Enable or Disable Processor Trace feature + Enable or Disable Processor Trace feature; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 ProcessorTraceEnable; + +/** Offset 0x007B +**/ + UINT8 UnusedUpdSpace4[5]; + +/** Offset 0x0080 - Base of memory region allocated for Processor Trace + Base address of memory region allocated for Processor Trace. Processor Trace requires + 2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable +**/ + UINT64 ProcessorTraceMemBase; + +/** Offset 0x0088 - Memory region allocation for Processor Trace + Length in bytes of memory region allocated for Processor Trace. Processor Trace + requires 2^N alignment and size in bytes per thread, from 4KB to 128MB. 0: Disable +**/ + UINT32 ProcessorTraceMemLength; + +/** Offset 0x008C - Enable or Disable Voltage Optimization feature + Enable or Disable Voltage Optimization feature 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 VoltageOptimization; + +/** Offset 0x008D - Set Three Strike Counter Disable + False (default): Three Strike counter will be incremented and True: Prevents Three + Strike counter from incrementing; 0: False; 1: True. + 0: False, 1: True +**/ + UINT8 ThreeStrikeCounterDisable; + +/** Offset 0x008E - Enable or Disable initialization of machine check registers + Enable or Disable initialization of machine check registers; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 MachineCheckEnable; + +/** Offset 0x008F - AP Idle Manner of waiting for SIPI + AP Idle Manner of waiting for SIPI; 1: HALT loop; 2: MWAIT loop; 3: RUN loop. + 1: HALT loop, 2: MWAIT loop, 3: RUN loop +**/ + UINT8 ApIdleManner; + +/** Offset 0x0090 - 1-Core Ratio Limit + 1-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 1-Core Ratio Limit + OC Bins.This 1-Core Ratio Limit Must be greater than or equal + to 2-Core Ratio Limit, 3-Core Ratio Limit, 4-Core Ratio Limit. Range is 0 to 83 +**/ + UINT8 OneCoreRatioLimit; + +/** Offset 0x0091 - 2-Core Ratio Limit + 2-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 2-Core Ratio Limit + OC Bins.This 2-Core Ratio Limit Must be Less than or equal + to 1-Core Ratio Limit.Range is 0 to 83 +**/ + UINT8 TwoCoreRatioLimit; + +/** Offset 0x0092 - 3-Core Ratio Limit + 3-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 3-Core Ratio Limit + OC Bins.This 3-Core Ratio Limit Must be Less than or equal + to 1-Core Ratio Limit.Range is 0 to 83 +**/ + UINT8 ThreeCoreRatioLimit; + +/** Offset 0x0093 - 4-Core Ratio Limit + 4-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 4-Core Ratio Limit + OC Bins.This 4-Core Ratio Limit Must be Less than or equal + to 1-Core Ratio Limit.Range is 0 to 83 +**/ + UINT8 FourCoreRatioLimit; + +/** Offset 0x0094 - 5-Core Ratio Limit + 5-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 5-Core Ratio Limit + OC Bins.This 5-Core Ratio Limit Must be Less than or equal + to 1-Core Ratio Limit.Range is 0 to 83 + 0x0:0xFF +**/ + UINT8 FiveCoreRatioLimit; + +/** Offset 0x0095 - 6-Core Ratio Limit + 6-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 6-Core Ratio Limit + OC Bins.This 6-Core Ratio Limit Must be Less than or equal + to 1-Core Ratio Limit.Range is 0 to 83 + 0x0:0xFF +**/ + UINT8 SixCoreRatioLimit; + +/** Offset 0x0096 - 7-Core Ratio Limit + 7-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 7-Core Ratio Limit + OC Bins.This 7-Core Ratio Limit Must be Less than or equal + to 1-Core Ratio Limit.Range is 0 to 83 + 0x0:0xFF +**/ + UINT8 SevenCoreRatioLimit; + +/** Offset 0x0097 - 8-Core Ratio Limit + 8-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused + 8-Core Ratio Limit + OC Bins.This 8-Core Ratio Limit Must be Less than or equal + to 1-Core Ratio Limit.Range is 0 to 83 + 0x0:0xFF +**/ + UINT8 EightCoreRatioLimit; + +/** Offset 0x0098 - Enable or Disable HWP + Enable or Disable HWP(Hardware P states) Support. 0: Disable; 1: Enable; + 2-3:Reserved + $EN_DIS +**/ + UINT8 Hwp; + +/** Offset 0x0099 - Hardware Duty Cycle Control + Hardware Duty Cycle Control configuration. 0: Disabled; 1: Enabled 2-3:Reserved + $EN_DIS +**/ + UINT8 HdcControl; + +/** Offset 0x009A - Package Long duration turbo mode time + Package Long duration turbo mode time window in seconds. Valid values(Unit in seconds) + 0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128 +**/ + UINT8 PowerLimit1Time; + +/** Offset 0x009B - Short Duration Turbo Mode + Enable or Disable short duration Turbo Mode. 0 : Disable; 1: Enable + $EN_DIS +**/ + UINT8 PowerLimit2; + +/** Offset 0x009C - Turbo settings Lock + Lock all Turbo settings Enable/Disable; 0: Disable , 1: Enable + $EN_DIS +**/ + UINT8 TurboPowerLimitLock; + +/** Offset 0x009D - Package PL3 time window + Package PL3 time window range for this policy from 0 to 64ms +**/ + UINT8 PowerLimit3Time; + +/** Offset 0x009E - Package PL3 Duty Cycle + Package PL3 Duty Cycle; Valid Range is 0 to 100 +**/ + UINT8 PowerLimit3DutyCycle; + +/** Offset 0x009F - Package PL3 Lock + Package PL3 Lock Enable/Disable; 0: Disable ; 1: Enable + $EN_DIS +**/ + UINT8 PowerLimit3Lock; + +/** Offset 0x00A0 - Package PL4 Lock + Package PL4 Lock Enable/Disable; 0: Disable ; 1: Enable + $EN_DIS +**/ + UINT8 PowerLimit4Lock; + +/** Offset 0x00A1 - TCC Activation Offset + TCC Activation Offset. Offset from factory set TCC activation temperature at which + the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation + Temperature, in volts.For SKL Y SKU, the recommended default for this policy is + 10, For all other SKUs the recommended default are 0 +**/ + UINT8 TccActivationOffset; + +/** Offset 0x00A2 - Tcc Offset Clamp Enable/Disable + Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle + below P1.For SKL Y SKU, the recommended default for this policy is 1: Enabled, + For all other SKUs the recommended default are 0: Disabled. + $EN_DIS +**/ + UINT8 TccOffsetClamp; + +/** Offset 0x00A3 - Tcc Offset Lock + Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature + target; 0: Disabled; 1: Enabled. + $EN_DIS +**/ + UINT8 TccOffsetLock; + +/** Offset 0x00A4 - Package Long duration turbo mode power limit + Package Long duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit. + Valid Range 0 to 4095875 in Step size of 125 +**/ + UINT32 PowerLimit1; + +/** Offset 0x00A8 - Package Short duration turbo mode power limit + Package Short duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 PowerLimit2Power; + +/** Offset 0x00AC - Package PL3 power limit + Package PL3 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 PowerLimit3; + +/** Offset 0x00B0 - Package PL4 power limit + Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 1023875 in Step size of 125 +**/ + UINT32 PowerLimit4; + +/** Offset 0x00B4 - Tcc Offset Time Window for RATL + Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 1023875 in Step size of 125 +**/ + UINT32 TccOffsetTimeWindowForRatl; + +/** Offset 0x00B8 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT + Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 HwpInterruptControl; + +/** Offset 0x00B9 - Intel Turbo Boost Max Technology 3.0 + Intel Turbo Boost Max Technology 3.0. 0: Disabled; 1: Enabled + $EN_DIS +**/ + UINT8 EnableItbm; + +/** Offset 0x00BA - Intel Turbo Boost Max Technology 3.0 Driver + Intel Turbo Boost Max Technology 3.0 Driver 0: Disabled; 1: Enabled + $EN_DIS +**/ + UINT8 EnableItbmDriver; + +/** Offset 0x00BB - Enable or Disable Per Core P State OS control + Enable or Disable Per Core P State OS control. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 EnablePerCorePState; + +/** Offset 0x00BC - Enable or Disable HwP Autonomous Per Core P State OS control + Enable or Disable HwP Autonomous Per Core P State OS control. 0: Disable; 1: + Enable + $EN_DIS +**/ + UINT8 EnableHwpAutoPerCorePstate; + +/** Offset 0x00BD - Enable or Disable HwP Autonomous EPP Grouping + Enable or Disable HwP Autonomous EPP Grouping. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 EnableHwpAutoEppGrouping; + +/** Offset 0x00BE - Enable or Disable EPB override over PECI + Enable or Disable EPB override over PECI. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 EnableEpbPeciOverride; + +/** Offset 0x00BF - Enable or Disable Fast MSR for IA32_HWP_REQUEST + Enable or Disable Fast MSR for IA32_HWP_REQUEST. 0: Disable;1: Enable + $EN_DIS +**/ + UINT8 EnableFastMsrHwpReq; + +/** Offset 0x00C0 - Minimum Ring ratio limit override + Minimum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo + ratio limit +**/ + UINT8 MinRingRatioLimit; + +/** Offset 0x00C1 - Maximum Ring ratio limit override + Maximum Ring ratio limit override. 0: Hardware defaults. Range: 0 - Max turbo + ratio limit +**/ + UINT8 MaxRingRatioLimit; + +/** Offset 0x00C2 - Custom Ratio State Entries + The number of custom ratio state entries, ranges from 0 to 40 for a valid custom + ratio table.Sets the number of custom P-states. At least 2 states must be present +**/ + UINT8 NumberOfEntries; + +/** Offset 0x00C3 - Custom Short term Power Limit time window + Short term Power Limit time window value for custom CTDP level 1. Valid Range 0 to 128 +**/ + UINT8 Custom1PowerLimit1Time; + +/** Offset 0x00C4 - Custom Short term Power Limit time window + Short term Power Limit time window value for custom CTDP level 2. Valid Range 0 to 128 +**/ + UINT8 Custom2PowerLimit1Time; + +/** Offset 0x00C5 - Custom Short term Power Limit time window + Short term Power Limit time window value for custom CTDP level 3. Valid Range 0 to 128 +**/ + UINT8 Custom3PowerLimit1Time; + +/** Offset 0x00C6 - Custom Turbo Activation Ratio + Turbo Activation Ratio for custom cTDP level 1. Valid Range 0 to 255 +**/ + UINT8 Custom1TurboActivationRatio; + +/** Offset 0x00C7 - Custom Turbo Activation Ratio + Turbo Activation Ratio for custom cTDP level 2. Valid Range 0 to 255 +**/ + UINT8 Custom2TurboActivationRatio; + +/** Offset 0x00C8 - Custom Turbo Activation Ratio + Turbo Activation Ratio for custom cTDP level 3. Valid Range 0 to 255 +**/ + UINT8 Custom3TurboActivationRatio; + +/** Offset 0x00C9 - ConfigTdp mode settings Lock + Lock the ConfigTdp mode settings from runtime changes; 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 ConfigTdpLock; + +/** Offset 0x00CA - Load Configurable TDP SSDT + Configure whether to load Configurable TDP SSDT; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 ConfigTdpBios; + +/** Offset 0x00CB - Max P-State Ratio + Max P-State Ratio, Valid Range 0 to 0x7F +**/ + UINT8 MaxRatio; + +/** Offset 0x00CC - P-state ratios for custom P-state table + P-state ratios for custom P-state table. NumberOfEntries has valid range between + 0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries] + are configurable. Valid Range of each entry is 0 to 0x7F +**/ + UINT8 StateRatio[40]; + +/** Offset 0x00F4 - Short term Power Limit value for custom cTDP level 1 + Short term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 Custom1PowerLimit1; + +/** Offset 0x00F8 - Long term Power Limit value for custom cTDP level 1 + Long term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 Custom1PowerLimit2; + +/** Offset 0x00FC - Short term Power Limit value for custom cTDP level 2 + Short term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 Custom2PowerLimit1; + +/** Offset 0x0100 - Long term Power Limit value for custom cTDP level 2 + Long term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 Custom2PowerLimit2; + +/** Offset 0x0104 - Short term Power Limit value for custom cTDP level 3 + Short term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 Custom3PowerLimit1; + +/** Offset 0x0108 - Long term Power Limit value for custom cTDP level 3 + Long term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid + Range 0 to 4095875 in Step size of 125 +**/ + UINT32 Custom3PowerLimit2; + +/** Offset 0x010C - PL1 Enable value + PL1 Enable value to limit average platform power. 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PsysPowerLimit1; + +/** Offset 0x010D - PL1 timewindow + PL1 timewindow in seconds.Valid values(Unit in seconds) 0 to 8 , 10 , 12 ,14 , 16 + , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128 +**/ + UINT8 PsysPowerLimit1Time; + +/** Offset 0x010E - PL2 Enable Value + PL2 Enable activates the PL2 value to limit average platform power.0: Disable; + 1: Enable. + $EN_DIS +**/ + UINT8 PsysPowerLimit2; + +/** Offset 0x010F +**/ + UINT8 UnusedUpdSpace5; + +/** Offset 0x0110 - Platform Power Pmax + PCODE MMIO Mailbox: Platform Power Pmax. 0 - Auto Specified in 1/8 Watt increments. + Range 0-1024 Watts. Value of 800 = 100W +**/ + UINT16 PsysPmax; + +/** Offset 0x0112 +**/ + UINT8 UnusedUpdSpace6[2]; + +/** Offset 0x0114 - Platform PL1 power + Platform PL1 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range + 0 to 4095875 in Step size of 125 +**/ + UINT32 PsysPowerLimit1Power; + +/** Offset 0x0118 - Platform PL2 power + Platform PL2 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range + 0 to 4095875 in Step size of 125 +**/ + UINT32 PsysPowerLimit2Power; + +/** Offset 0x011C - Enable or Disable Intel SpeedStep Technology + Enable or Disable Intel SpeedStep Technology. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 Eist; + +/** Offset 0x011D - Enable or Disable Energy Efficient P-state + Enable or Disable Energy Efficient P-state will be applied in Turbo mode. Disable; + 1: Enable + $EN_DIS +**/ + UINT8 EnergyEfficientPState; + +/** Offset 0x011E - Enable or Disable Energy Efficient Turbo + Enable or Disable Energy Efficient Turbo, will be applied in Turbo mode. Disable; + 1: Enable + $EN_DIS +**/ + UINT8 EnergyEfficientTurbo; + +/** Offset 0x011F - Enable or Disable T states + Enable or Disable T states; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 TStates; + +/** Offset 0x0120 - Enable or Disable Bi-Directional PROCHOT# + Enable or Disable Bi-Directional PROCHOT#; 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 BiProcHot; + +/** Offset 0x0121 - Enable or Disable PROCHOT# signal being driven externally + Enable or Disable PROCHOT# signal being driven externally; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 DisableProcHotOut; + +/** Offset 0x0122 - Enable or Disable PROCHOT# Response + Enable or Disable PROCHOT# Response; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 ProcHotResponse; + +/** Offset 0x0123 - Enable or Disable VR Thermal Alert + Enable or Disable VR Thermal Alert; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 DisableVrThermalAlert; + +/** Offset 0x0124 - Enable or Disable Thermal Reporting + Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 AutoThermalReporting; + +/** Offset 0x0125 - Enable or Disable Thermal Monitor + Enable or Disable Thermal Monitor; 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 ThermalMonitor; + +/** Offset 0x0126 - Enable or Disable CPU power states (C-states) + Enable or Disable CPU power states (C-states). 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 Cx; + +/** Offset 0x0127 - Configure C-State Configuration Lock + Configure C-State Configuration Lock; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PmgCstCfgCtrlLock; + +/** Offset 0x0128 - Enable or Disable Enhanced C-states + Enable or Disable Enhanced C-states. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 C1e; + +/** Offset 0x0129 - Enable or Disable C1 Cstate Demotion + Enable or Disable C1 Cstate Demotion. Disable; 1: Enable + $EN_DIS +**/ + UINT8 C1StateAutoDemotion; + +/** Offset 0x012A - Enable or Disable C1 Cstate UnDemotion + Enable or Disable C1 Cstate UnDemotion. Disable; 1: Enable + $EN_DIS +**/ + UINT8 C1StateUnDemotion; + +/** Offset 0x012B - Enable or Disable Package Cstate Demotion + Enable or Disable Package Cstate Demotion. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 PkgCStateDemotion; + +/** Offset 0x012C - Enable or Disable Package Cstate UnDemotion + Enable or Disable Package Cstate UnDemotion. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 PkgCStateUnDemotion; + +/** Offset 0x012D - Enable or Disable CState-Pre wake + Enable or Disable CState-Pre wake. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 CStatePreWake; + +/** Offset 0x012E - Enable or Disable TimedMwait Support. + Enable or Disable TimedMwait Support. 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 TimedMwait; + +/** Offset 0x012F - Enable or Disable IO to MWAIT redirection + Enable or Disable IO to MWAIT redirection; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 CstCfgCtrIoMwaitRedirection; + +/** Offset 0x0130 - Set the Max Pkg Cstate + Set the Max Pkg Cstate. Default set to Auto which limits the Max Pkg Cstate to deep + C-state. Valid values 0 - C0/C1 , 1 - C2 , 2 - C3 , 3 - C6 , 4 - C7 , 5 - C7S , + 6 - C8 , 7 - C9 , 8 - C10 , 254 - CPU Default , 255 - Auto +**/ + UINT8 PkgCStateLimit; + +/** Offset 0x0131 - TimeUnit for C-State Latency Control1 + TimeUnit for C-State Latency Control1;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns + , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns +**/ + UINT8 CstateLatencyControl1TimeUnit; + +/** Offset 0x0132 - TimeUnit for C-State Latency Control2 + TimeUnit for C-State Latency Control2;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns + , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns +**/ + UINT8 CstateLatencyControl2TimeUnit; + +/** Offset 0x0133 - TimeUnit for C-State Latency Control3 + TimeUnit for C-State Latency Control3;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns + , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns +**/ + UINT8 CstateLatencyControl3TimeUnit; + +/** Offset 0x0134 - TimeUnit for C-State Latency Control4 + Time - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns +**/ + UINT8 CstateLatencyControl4TimeUnit; + +/** Offset 0x0135 - TimeUnit for C-State Latency Control5 + TimeUnit for C-State Latency Control5;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns + , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns +**/ + UINT8 CstateLatencyControl5TimeUnit; + +/** Offset 0x0136 - Interrupt Redirection Mode Select + Interrupt Redirection Mode Select.0: Fixed priority; 1: Round robin;2: Hash vector;7: + No change. +**/ + UINT8 PpmIrmSetting; + +/** Offset 0x0137 - Lock prochot configuration + Lock prochot configuration Enable/Disable; 0: Disable; 1: Enable + $EN_DIS +**/ + UINT8 ProcHotLock; + +/** Offset 0x0138 - Race To Halt + Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency + in order to enter pkg C-State faster to reduce overall power. (RTH is controlled + through MSR 1FC bit 20)Disable; 1: Enable + $EN_DIS +**/ + UINT8 RaceToHalt; + +/** Offset 0x0139 - Configuration for boot TDP selection + Configuration for boot TDP selection; 0: TDP Nominal; 1: TDP Down; 2: TDP + Up;0xFF : Deactivate +**/ + UINT8 ConfigTdpLevel; + +/** Offset 0x013A - Interrupt Response Time Limit of C-State LatencyContol1 + Interrupt Response Time Limit of C-State LatencyContol1.Range of value 0 to 0x3FF. + 0 is Auto. +**/ + UINT16 CstateLatencyControl1Irtl; + +/** Offset 0x013C - Interrupt Response Time Limit of C-State LatencyContol2 + Interrupt Response Time Limit of C-State LatencyContol2.Range of value 0 to 0x3FF. + 0 is Auto. +**/ + UINT16 CstateLatencyControl2Irtl; + +/** Offset 0x013E - Interrupt Response Time Limit of C-State LatencyContol3 + Interrupt Response Time Limit of C-State LatencyContol3.Range of value 0 to 0x3FF. + 0 is Auto. +**/ + UINT16 CstateLatencyControl3Irtl; + +/** Offset 0x0140 - Interrupt Response Time Limit of C-State LatencyContol4 + Interrupt Response Time Limit of C-State LatencyContol4.Range of value 0 to 0x3FF. + 0 is Auto. +**/ + UINT16 CstateLatencyControl4Irtl; + +/** Offset 0x0142 - Interrupt Response Time Limit of C-State LatencyContol5. 0 is Auto. + Interrupt Response Time Limit of C-State LatencyContol5.Range of value 0 to 0x3FF. + 0 is Auto. +**/ + UINT16 CstateLatencyControl5Irtl; + +/** Offset 0x0144 - P-state ratios for max 16 version of custom P-state table + P-state ratios for max 16 version of custom P-state table. This table is used for + OS versions limited to a max of 16 P-States. If the first entry of this table is + 0, or if Number of Entries is 16 or less, then this table will be ignored, and + up to the top 16 values of the StateRatio table will be used instead. Valid Range + of each entry is 0 to 0x7F +**/ + UINT8 StateRatioMax16[16]; + +/** Offset 0x0154 - CpuBistData + Pointer CPU BIST Data +**/ + UINT32 CpuBistData; + +/** Offset 0x0158 - CpuMpPpi + Pointer for CpuMpPpi +**/ + UINT32 CpuMpPpi; + +/** Offset 0x015C - CpuMpHob + Pointer for CpuMpHob. This is optional data buffer for CpuMpPpi usage. +**/ + UINT32 CpuMpHob; + +/** Offset 0x0160 +**/ + UINT8 CpuPostMemRsvd[16]; + +/** Offset 0x0170 - BgpdtHash[4] + BgpdtHash values +**/ + UINT64 BgpdtHash[4]; + +/** Offset 0x0190 - BiosGuardAttr + BiosGuardAttr default values +**/ + UINT32 BiosGuardAttr; + +/** Offset 0x0194 +**/ + UINT8 UnusedUpdSpace7[4]; + +/** Offset 0x0198 - BiosGuardModulePtr + BiosGuardModulePtr default values +**/ + UINT64 BiosGuardModulePtr; + +/** Offset 0x01A0 - SendEcCmd + SendEcCmd function pointer. \n + @code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE + EcCmdType, IN UINT8 EcCmd, IN UINT8 SendData, IN OUT UINT8 *ReceiveData); @endcode +**/ + UINT64 SendEcCmd; + +/** Offset 0x01A8 - EcCmdProvisionEav + Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC +**/ + UINT8 EcCmdProvisionEav; + +/** Offset 0x01A9 - EcCmdLock + EcCmdLock default values. Locks Ephemeral Authorization Value sent previously +**/ + UINT8 EcCmdLock; + +/** Offset 0x01AA +**/ + UINT8 UnusedUpdSpace8[6]; + +/** Offset 0x01B0 - SgxEpoch0 + SgxEpoch0 default values +**/ + UINT64 SgxEpoch0; + +/** Offset 0x01B8 - SgxEpoch1 + SgxEpoch1 default values +**/ + UINT64 SgxEpoch1; + +/** Offset 0x01C0 - SgxSinitNvsData + SgxSinitNvsData default values +**/ + UINT8 SgxSinitNvsData; + +/** Offset 0x01C1 - SgxSinitDataFromTpm + SgxSinitDataFromTpm default values +**/ + UINT8 SgxSinitDataFromTpm; + +/** Offset 0x01C2 +**/ + UINT8 SecurityPostMemRsvd[16]; + +/** Offset 0x01D2 - Enable Device 4 + Enable/disable Device 4 + $EN_DIS +**/ + UINT8 Device4Enable; + +/** Offset 0x01D3 - DEPRECATED SA CRID + Deprecated, use FSPM_UPD.FspmConfig.CridEnable instead + $EN_DIS +**/ + UINT8 CridEnableDeprecated; + +/** Offset 0x01D4 - Skip PAM register lock + Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default): + PAM registers will be locked by RC + $EN_DIS +**/ + UINT8 SkipPamLock; + +/** Offset 0x01D5 - EDRAM Test Mode + Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default): + PAM registers will be locked by RC + 0: EDRAM SW disable, 1: EDRAM SW Enable, 2: EDRAM HW mode +**/ + UINT8 EdramTestMode; + +/** Offset 0x01D6 - DMI ASPM + 0=Disable, 1:L0s, 2:L1, 3(Default)=L0sL1 + 0:Disable, 1:L0s, 2:L1, 3:L0sL1 +**/ + UINT8 DmiAspm; + +/** Offset 0x01D7 - PchDmiCwbEnable + Central Write Buffer feature configurable and disabled by default + $EN_DIS +**/ + UINT8 PchDmiCwbEnable; + +/** Offset 0x01D8 - DMI Extended Sync Control + Enable: Enable DMI Extended Sync Control, Disable(Default): Disable DMI Extended + Sync Control + $EN_DIS +**/ + UINT8 DmiExtSync; + +/** Offset 0x01D9 - DMI IOT Control + Enable: Enable DMI IOT Control, Disable(Default): Disable DMI IOT Control + $EN_DIS +**/ + UINT8 DmiIot; + +/** Offset 0x01DA - PCIe DeEmphasis control per root port + 0: -6dB, 1(Default): -3.5dB + 0:-6dB, 1:-3.5dB +**/ + UINT8 PegDeEmphasis[4]; + +/** Offset 0x01DE - PCIe Slot Power Limit value per root port + Slot power limit value per root port +**/ + UINT8 PegSlotPowerLimitValue[4]; + +/** Offset 0x01E2 - PCIe Slot Power Limit scale per root port + Slot power limit scale per root port + 0:1.0x, 1:0.1x, 2:0.01x, 3:0x001x +**/ + UINT8 PegSlotPowerLimitScale[4]; + +/** Offset 0x01E6 - PCIe Physical Slot Number per root port + Physical Slot Number per root port +**/ + UINT16 PegPhysicalSlotNumber[4]; + +/** Offset 0x01EE - PEG Max Payload size per root port + 0xFF(Default):Auto, 0x1: Force 128B, 0x2: Force 256B + 0xFF: Auto, 0x1: Force 128B, 0x2: Force 256B +**/ + UINT8 PegMaxPayload[4]; + +/** Offset 0x01F2 +**/ + UINT8 UnusedUpdSpace9[2]; + +/** Offset 0x01F4 - Graphics Configuration Ptr + Points to VBT +**/ + UINT32 GraphicsConfigPtr; + +/** Offset 0x01F8 - Logo Pointer + Points to PEI Display Logo Image +**/ + UINT32 LogoPtr; + +/** Offset 0x01FC - Logo Size + Size of PEI Display Logo Image +**/ + UINT32 LogoSize; + +/** Offset 0x0200 - Blt Buffer Address + Address of Blt buffer +**/ + UINT32 BltBufferAddress; + +/** Offset 0x0204 - Blt Buffer Size + Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of + EFI_GRAPHICS_OUTPUT_BLT_PIXEL) +**/ + UINT32 BltBufferSize; + +/** Offset 0x0208 - Enable/Disable PavpEnable + Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable + $EN_DIS +**/ + UINT8 PavpEnable; + +/** Offset 0x0209 - CdClock Frequency selection + 0: (Default) Auto (Max based on reference clock frequency), 1: 307.2, 2: 312 Mhz, + 3: 552 Mhz, 4: 556.8 Mhz, 5: 648 Mhz, 6: 652.8 Mhz + 0: Auto (Max based on reference clock frequency), 1: 307.2, 2: 312 Mhz, 3: 552 Mhz, + 4: 556.8 Mhz, 5: 648 Mhz, 6: 652.8 Mhz +**/ + UINT8 CdClock; + +/** Offset 0x020A - Enable/Disable PeiGraphicsPeimInit + Enable: Enable PeiGraphicsPeimInit, Disable(Default): Disable PeiGraphicsPeimInit + $EN_DIS +**/ + UINT8 PeiGraphicsPeimInit; + +/** Offset 0x020B - Enable/Disable IGFX RenderStandby + Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby + $EN_DIS +**/ + UINT8 RenderStandby; + +/** Offset 0x020C - Enable/Disable IGFX PmSupport + Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport + $EN_DIS +**/ + UINT8 PmSupport; + +/** Offset 0x020D - Enable/Disable CdynmaxClamp + Enable: Enable CdynmaxClamp, Disable(Default): Disable CdynmaxClamp + $EN_DIS +**/ + UINT8 CdynmaxClampEnable; + +/** Offset 0x020E - GT Frequency Limit + 0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz, + 7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD: + 650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz, + 0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz, + 0x18: 1200 Mhz + 0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz, + 7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD: + 650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz, + 0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz, + 0x18: 1200 Mhz +**/ + UINT8 GtFreqMax; + +/** Offset 0x020F - Disable Turbo GT + 0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency + $EN_DIS +**/ + UINT8 DisableTurboGt; + +/** Offset 0x0210 - Enable/Disable CdClock Init + Enable: Skip Full CD clock initializaton, Disable(Default): Initialize the full + CD clock if not initialized by Gfx PEIM + $EN_DIS +**/ + UINT8 SkipCdClockInit; + +/** Offset 0x0211 - Enable or disable HPD of DDI port-A device + 0=Disabled,1(Default)=eDP, 2=MIPI DSI + 0:Disabled, 1:eDP, 2:MIPI DSI +**/ + UINT8 DdiPortAConfig; + +/** Offset 0x0212 - Enable or disable HPD of DDI port B + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPortBHpd; + +/** Offset 0x0213 - Enable or disable HPD of DDI port C + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPortCHpd; + +/** Offset 0x0214 - Enable or disable HPD of DDI port 1 + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPort1Hpd; + +/** Offset 0x0215 - Enable or disable HPD of DDI port 2 + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPort2Hpd; + +/** Offset 0x0216 - Enable or disable HPD of DDI port 3 + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPort3Hpd; + +/** Offset 0x0217 - Enable or disable HPD of DDI port 4 + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPort4Hpd; + +/** Offset 0x0218 - Enable or disable DDC of DDI port B + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPortBDdc; + +/** Offset 0x0219 - Enable or disable DDC of DDI port C + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 DdiPortCDdc; + +/** Offset 0x021A - Enable DDC setting of DDI Port 1 + 0=Disable, 1=DDC(Default) + 0: Disable, 1: DDC +**/ + UINT8 DdiPort1Ddc; + +/** Offset 0x021B - Enable DDC setting of DDI Port 2 + 0=Disable, 1=DDC(Default) + 0: Disable, 1: DDC +**/ + UINT8 DdiPort2Ddc; + +/** Offset 0x021C - Enable DDC setting of DDI Port 3 + 0=Disable, 1=DDC(Default) + 0: Disable, 1: DDC +**/ + UINT8 DdiPort3Ddc; + +/** Offset 0x021D - Enable DDC setting of DDI Port 4 + 0=Disable, 1=DDC(Default) + 0: Disable, 1: DDC +**/ + UINT8 DdiPort4Ddc; + +/** Offset 0x021E - Enable or disable GNA device + 0=Disable, 1(Default)=Enable + $EN_DIS +**/ + UINT8 GnaEnable; + +/** Offset 0x021F - USB override in IOM + This policy will enable/disable USB Connect override in IOM + $EN_DIS +**/ + UINT8 UsbOverride; + +/** Offset 0x0220 - VCCST request for IOM + This policy will enable/disable VCCST and also decides if message would be replayed in S4/S5 + $EN_DIS +**/ + UINT8 VccSt; + +/** Offset 0x0221 - Enable D3 Hot in TCSS + This policy will enable/disable D3 hot support in IOM + $EN_DIS +**/ + UINT8 D3HotEnable; + +/** Offset 0x0222 - Enable D3 Cold in TCSS + This policy will enable/disable D3 cold support in IOM + $EN_DIS +**/ + UINT8 D3ColdEnable; + +/** Offset 0x0223 - Enable/Disable PMC-PD Solution + This policy will enable/disable PMC-PD Solution vs EC-TCPC Solution + $EN_DIS +**/ + UINT8 PmcPdEnable; + +/** Offset 0x0224 - Enable/Disable PTM + This policy will enable/disable Precision Time Measurement for TCSS PCIe Root Ports + $EN_DIS +**/ + UINT8 PtmEnabled[4]; + +/** Offset 0x0228 - PCIE RP Ltr Enable + Latency Tolerance Reporting Mechanism. +**/ + UINT8 SaPcieItbtRpLtrEnable[4]; + +/** Offset 0x022C - PCIE RP Snoop Latency Override Mode + Latency Tolerance Reporting, Snoop Latency Override Mode. +**/ + UINT8 SaPcieItbtRpSnoopLatencyOverrideMode[4]; + +/** Offset 0x0230 - PCIE RP Snoop Latency Override Multiplier + Latency Tolerance Reporting, Snoop Latency Override Multiplier. +**/ + UINT8 SaPcieItbtRpSnoopLatencyOverrideMultiplier[4]; + +/** Offset 0x0234 - PCIE RP Snoop Latency Override Value + Latency Tolerance Reporting, Snoop Latency Override Value. +**/ + UINT16 SaPcieItbtRpSnoopLatencyOverrideValue[4]; + +/** Offset 0x023C - PCIE RP Non Snoop Latency Override Mode + Latency Tolerance Reporting, Non-Snoop Latency Override Mode. +**/ + UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMode[4]; + +/** Offset 0x0240 - PCIE RP Non Snoop Latency Override Multiplier + Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier. +**/ + UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMultiplier[4]; + +/** Offset 0x0244 - PCIE RP Non Snoop Latency Override Value + Latency Tolerance Reporting, Non-Snoop Latency Override Value. +**/ + UINT16 SaPcieItbtRpNonSnoopLatencyOverrideValue[4]; + +/** Offset 0x024C - Force LTR Override + Force LTR Override. +**/ + UINT8 SaPcieItbtRpForceLtrOverride[4]; + +/** Offset 0x0250 - PCIE RP Ltr Config Lock + 0: Disable; 1: Enable. +**/ + UINT8 SaPcieItbtRpLtrConfigLock[4]; + +/** Offset 0x0254 - Enable VMD controller + Enable/disable to VMD controller. + $EN_DIS +**/ + UINT8 VmdEnable; + +/** Offset 0x0255 - Enable VMD portA Support + Enable/disable to VMD portA Support. + $EN_DIS +**/ + UINT8 VmdPortA; + +/** Offset 0x0256 - Enable VMD portB Support + Enable/disable to VMD portB Support. + $EN_DIS +**/ + UINT8 VmdPortB; + +/** Offset 0x0257 - Enable VMD portC Support + Enable/disable to VMD portC Support. + $EN_DIS +**/ + UINT8 VmdPortC; + +/** Offset 0x0258 - Enable VMD portD Support + Enable/disable to VMD portD Support. + $EN_DIS +**/ + UINT8 VmdPortD; + +/** Offset 0x0259 - VMD Config Bar size + Set The VMD Config Bar Size. +**/ + UINT8 VmdCfgBarSz; + +/** Offset 0x025A - VMD Config Bar Attributes + 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH(Default) + 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH +**/ + UINT8 VmdCfgBarAttr; + +/** Offset 0x025B - VMD Mem Bar1 size + Set The VMD Mem Bar1 Size. +**/ + UINT8 VmdMemBarSz1; + +/** Offset 0x025C - VMD Mem Bar1 Attributes + 0: VMD_32BIT_NONPREFETCH(Default), 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH + 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH +**/ + UINT8 VmdMemBar1Attr; + +/** Offset 0x025D - VMD Mem Bar2 size + Set The VMD Mem Bar2 Size. +**/ + UINT8 VmdMemBarSz2; + +/** Offset 0x025E - VMD Mem Bar2 Attributes + 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH(Default), 2: VMD_64BIT_PREFETCH + 0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH +**/ + UINT8 VmdMemBar2Attr; + +/** Offset 0x025F +**/ + UINT8 UnusedUpdSpace10[1]; + +/** Offset 0x0260 - TypeC port GPIO setting + GPIO Ping number for Type C Aux Oritation setting, use the GpioPad that is defined + in GpioPinsXXXH.h and GpioPinsXXXLp.h as argument.(XXX is platform name, Ex: Icl + = IceLake) +**/ + UINT32 IomTypeCPortPadCfg[8]; + +/** Offset 0x0280 - TCSS Aux Orientation Override Enable + Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides +**/ + UINT16 TcssAuxOri; + +/** Offset 0x0282 - TCSS HSL Orientation Override Enable + Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides +**/ + UINT16 TcssHslOri; + +/** Offset 0x0284 - PCH USB OverCurrent mapping enable + 1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin + mapping allow for NOA usage of OC pins + $EN_DIS +**/ + UINT8 PchUsbOverCurrentEnable; + +/** Offset 0x0285 - CPU USB3 Port Over Current Pin + Describe the specific over current pin number of USBC Port N. +**/ + UINT8 CpuUsb3OverCurrentPin[8]; + +/** Offset 0x028D - TCSS USB Port Enable + Bits 0, 1, ... max Type C port control enables +**/ + UINT8 UsbTcPortEn; + +/** Offset 0x028E +**/ + UINT8 UnusedUpdSpace11[2]; + +/** Offset 0x0290 - ITBT DMA UUID + TCSS DMA1, DMA2 UUID Number +**/ + UINT32 IclAxITbtDmaUuid[2]; + +/** Offset 0x0298 - ITBT Root Port Enable + ITBT Root Port Enable, 0:Disable, 1:Enable + 0:Disable, 1:Enable +**/ + UINT8 ITbtPcieRootPortEn[4]; + +/** Offset 0x029C - ITBTForcePowerOn Timeout value + ITBTForcePowerOn value. Specified increment values in miliseconds. Range is 0-1000. + 100 = 100 ms. +**/ + UINT16 ITbtForcePowerOnTimeoutInMs; + +/** Offset 0x029E - ITbtConnectTopology Timeout value + ITbtConnectTopologyTimeout value. Specified increment values in miliseconds. Range + is 0-10000. 100 = 100 ms. +**/ + UINT16 ITbtConnectTopologyTimeoutInMs; + +/** Offset 0x02A0 - TcssXhciEnableComplianceMode + Set Compliance Mode. 0:Disabled 1:Enabled + $EN_DIS +**/ + UINT8 TcssXhciEnableComplianceMode; + +/** Offset 0x02A1 - Enable/Disable PEG GEN3 Static EQ Phase1 programming + Program Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets + Programming, Enabled(0x1)(Default): Enable EQ Phase1 Static Presets Programming + $EN_DIS +**/ + UINT8 SaPcieGen3ProgramStaticEq; + +/** Offset 0x02A2 - Enable/Disable GEN4 Static EQ Phase1 programming + Program Gen4 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets + Programming, Enabled(0x1)(Default): Enable EQ Phase1 Static Presets Programming + $EN_DIS +**/ + UINT8 SaPcieGen4ProgramStaticEq; + +/** Offset 0x02A3 - TcssLoopbackModeBitMap + Set Loopback Mode Bit Map. 0:Disabled 1:Enabled + $EN_DIS +**/ + UINT8 TcssLoopbackModeBitMap; + +/** Offset 0x02A4 - ITBT DMA UUID + TCSS DMA1, DMA2 LTR value +**/ + UINT16 ITbtDmaLtr[2]; + +/** Offset 0x02A8 +**/ + UINT8 SaPostMemRsvd[3]; + +/** Offset 0x02AB - HECI3 state + The HECI3 state from Mbp for reference in S3 path or when MbpHob is not installed. + 0: disable, 1: enable + $EN_DIS +**/ + UINT8 Heci3Enabled; + +/** Offset 0x02AC - ME Unconfig on RTC clear + 0: Disable ME Unconfig On Rtc Clear. 1: Enable ME Unconfig On Rtc Clear. + 2: Cmos is clear, status unkonwn. 3: Reserved + 0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos + is clear, 3: Reserved +**/ + UINT8 MeUnconfigOnRtcClear; + +/** Offset 0x02AD - End of Post message + Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1): + EOP send in PEI, Send in DXE(0x2)(Default): EOP send in DXE + 0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved +**/ + UINT8 EndOfPostMessage; + +/** Offset 0x02AE - D0I3 Setting for HECI Disable + Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all + HECI devices + $EN_DIS +**/ + UINT8 DisableD0I3SettingForHeci; + +/** Offset 0x02AF - Mctp Broadcast Cycle + Test, Determine if MCTP Broadcast is enabled 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 MctpBroadcastCycle; + +/** Offset 0x02B0 +**/ + UINT8 MePostMemRsvd[10]; + +/** Offset 0x02BA - AMT Switch + Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality. + $EN_DIS +**/ + UINT8 AmtEnabled; + +/** Offset 0x02BB - WatchDog Timer Switch + Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. + $EN_DIS +**/ + UINT8 WatchDog; + +/** Offset 0x02BC - ASF Switch + Enable/Disable. 0: Disable, 1: enable, Enable or disable ASF functionality. + $EN_DIS +**/ + UINT8 AsfEnabled; + +/** Offset 0x02BD - PET Progress + Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive + PET Events. + $EN_DIS +**/ + UINT8 FwProgress; + +/** Offset 0x02BE - OS Timer + 16 bits Value, Set OS watchdog timer. + $EN_DIS +**/ + UINT16 WatchDogTimerOs; + +/** Offset 0x02C0 - BIOS Timer + 16 bits Value, Set BIOS watchdog timer. + $EN_DIS +**/ + UINT16 WatchDogTimerBios; + +/** Offset 0x02C2 - Manageability Mode set by Mebx + Enable/Disable. 0: Disable, 1: enable, Enable or disable Manageability Mode. + $EN_DIS +**/ + UINT8 ManageabilityMode; + +/** Offset 0x02C3 - SOL Switch + Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx + $EN_DIS +**/ + UINT8 AmtSolEnabled; + +/** Offset 0x02C4 - Remote Assistance Trigger Availablilty + Enable/Disable. 0: Disable, 1: enable, Remote Assistance enable/disable state by Mebx + $EN_DIS +**/ + UINT8 RemoteAssistance; + +/** Offset 0x02C5 - KVM Switch + Enable/Disable. 0: Disable, 1: enable, KVM enable/disable state by Mebx + $EN_DIS +**/ + UINT8 AmtKvmEnabled; + +/** Offset 0x02C6 - MEBX execution + Enable/Disable. 0: Disable, 1: enable, Force MEBX execution + $EN_DIS +**/ + UINT8 ForcMebxSyncUp; + +/** Offset 0x02C7 +**/ + UINT8 AmtPostMemRsvd[10]; + +/** Offset 0x02D1 - SPI0 Chip Select Polarity + Sets polarity for each chip Select. Available options: 0:PchSerialIoCsActiveLow, + 1:PchSerialIoCsActiveHigh +**/ + UINT8 SerialIoSpi0CsPolarity[2]; + +/** Offset 0x02D3 - SPI1 Chip Select Polarity + Sets polarity for each chip Select. Available options: 0:PchSerialIoCsActiveLow, + 1:PchSerialIoCsActiveHigh +**/ + UINT8 SerialIoSpi1CsPolarity[2]; + +/** Offset 0x02D5 - SPI2 Chip Select Polarity + Sets polarity for each chip Select. Available options: 0:PchSerialIoCsActiveLow, + 1:PchSerialIoCsActiveHigh +**/ + UINT8 SerialIoSpi2CsPolarity[2]; + +/** Offset 0x02D7 - SPI0 Chip Select Enable + 0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled +**/ + UINT8 SerialIoSpi0CsEnable[2]; + +/** Offset 0x02D9 - SPI1 Chip Select Enable + 0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled +**/ + UINT8 SerialIoSpi1CsEnable[2]; + +/** Offset 0x02DB - SPI2 Chip Select Enable + 0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled +**/ + UINT8 SerialIoSpi2CsEnable[2]; + +/** Offset 0x02DD - SPIn Device Mode + Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available + modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden +**/ + UINT8 SerialIoSpiMode[3]; + +/** Offset 0x02E0 - SPIn Default Chip Select Output + Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available + options: 0:CS0, 1:CS1 +**/ + UINT8 SerialIoSpiDefaultCsOutput[3]; + +/** Offset 0x02E3 - SPIn Default Chip Select Mode HW/SW + Sets Default CS Mode Hardware or Software. N represents controller index: SPI0, + SPI1, ... Available options: 0:HW, 1:SW +**/ + UINT8 SerialIoSpiCsMode[3]; + +/** Offset 0x02E6 - SPIn Default Chip Select State Low/High + Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ... + Available options: 0:Low, 1:High +**/ + UINT8 SerialIoSpiCsState[3]; + +/** Offset 0x02E9 - PCH SerialIo I2C Pads Termination + 0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up, + 0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,I2C2,I2C3,I2C4,I2C5 + pads termination respectively. One byte for each controller, byte0 for I2C0, byte1 + for I2C1, and so on. +**/ + UINT8 PchSerialIoI2cPadsTermination[6]; + +/** Offset 0x02EF - I2Cn Device Mode + Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available + modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden +**/ + UINT8 SerialIoI2cMode[6]; + +/** Offset 0x02F5 - UARTn Device Mode + Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available + modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom, + 4:SerialIoUartSkipInit +**/ + UINT8 SerialIoUartMode[3]; + +/** Offset 0x02F8 - Default BaudRate for each Serial IO UART + Set default BaudRate Supported from 0 - default to 6000000 +**/ + UINT32 SerialIoUartBaudRate[3]; + +/** Offset 0x0304 - Default ParityType for each Serial IO UART + Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity +**/ + UINT8 SerialIoUartParity[3]; + +/** Offset 0x0307 - Default DataBits for each Serial IO UART + Set default word length. 0: Default, 5,6,7,8 +**/ + UINT8 SerialIoUartDataBits[3]; + +/** Offset 0x030A - Default StopBits for each Serial IO UART + Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3: + TwoStopBits +**/ + UINT8 SerialIoUartStopBits[3]; + +/** Offset 0x030D - Power Gating mode for each Serial IO UART that works in COM mode + Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto +**/ + UINT8 SerialIoUartPowerGating[3]; + +/** Offset 0x0310 - Enable Dma for each Serial IO UART that supports it + Set DMA/PIO mode. 0: Disabled, 1: Enabled +**/ + UINT8 SerialIoUartDmaEnable[3]; + +/** Offset 0x0313 - Enables UART hardware flow control, CTS and RTS lines + Enables UART hardware flow control, CTS and RTS lines. +**/ + UINT8 SerialIoUartAutoFlow[3]; + +/** Offset 0x0316 +**/ + UINT8 UnusedUpdSpace12[2]; + +/** Offset 0x0318 - SerialIoUartRxPinMux + Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for + possible values. +**/ + UINT32 SerialIoUartRxPinMux[3]; + +/** Offset 0x0324 - SerialIoUartTxPinMux + Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for + possible values. +**/ + UINT32 SerialIoUartTxPinMux[3]; + +/** Offset 0x0330 - SerialIoUartRtsPinMux + Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS* + for possible values. +**/ + UINT32 SerialIoUartRtsPinMux[3]; + +/** Offset 0x033C - SerialIoUartCtsPinMux + Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS* + for possible values. +**/ + UINT32 SerialIoUartCtsPinMux[3]; + +/** Offset 0x0348 - UART Number For Debug Purpose + UART number for debug purpose. 0:UART0, 1: UART1, 2:UART2. Note: If UART0 is selected + as CNVi BT Core interface, it cannot be used for debug purpose. + 0:UART0, 1:UART1, 2:UART2 +**/ + UINT8 SerialIoDebugUartNumber; + +/** Offset 0x0349 - Enable LAN + Enable/disable LAN controller. + $EN_DIS +**/ + UINT8 PchLanEnable; + +/** Offset 0x034A - Enable PCH Lan LTR capabilty of PCH internal LAN + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchLanLtrEnable; + +/** Offset 0x034B - Enable HD Audio DSP + Enable/disable HD Audio DSP feature. + $EN_DIS +**/ + UINT8 PchHdaDspEnable; + +/** Offset 0x034C - Enable Pme + Enable Azalia wake-on-ring. + $EN_DIS +**/ + UINT8 PchHdaPme; + +/** Offset 0x034D - VC Type + Virtual Channel Type Select: 0: VC0, 1: VC1. + 0: VC0, 1: VC1 +**/ + UINT8 PchHdaVcType; + +/** Offset 0x034E - HD Audio Link Frequency + HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz. + 0: 6MHz, 1: 12MHz, 2: 24MHz +**/ + UINT8 PchHdaLinkFrequency; + +/** Offset 0x034F - iDisp-Link Frequency + iDisp-Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 4: 96MHz, 3: 48MHz. + 4: 96MHz, 3: 48MHz +**/ + UINT8 PchHdaIDispLinkFrequency; + +/** Offset 0x0350 - iDisp-Link T-mode + iDisp-Link T-Mode (PCH_HDAUDIO_IDISP_TMODE enum): 0: 2T, 2: 4T, 3: 8T, 4: 16T + 0: 2T, 2: 4T, 3: 8T, 4: 16T +**/ + UINT8 PchHdaIDispLinkTmode; + +/** Offset 0x0351 - Universal Audio Architecture compliance for DSP enabled system + 0: Not-UAA Compliant (Intel SST driver supported only), 1: UAA Compliant (HDA Inbox + driver or SST driver supported). + $EN_DIS +**/ + UINT8 PchHdaDspUaaCompliance; + +/** Offset 0x0352 - iDisplay Audio Codec disconnection + 0: Not disconnected, enumerable, 1: Disconnected SDI, not enumerable. + $EN_DIS +**/ + UINT8 PchHdaIDispCodecDisconnect; + +/** Offset 0x0353 - PCH HDA Codec Sx Wake Capability + Capability to detect wake initiated by a codec in Sx +**/ + UINT8 PchHdaCodecSxWakeCapability; + +/** Offset 0x0354 - HD Audio Reset Wait Timer + The delay timer after Azalia reset, the value is number of microseconds. Default is 600. +**/ + UINT16 PchHdaResetWaitTimer; + +/** Offset 0x0356 - PCH HDA Verb Table Entry Number + Number of Entries in Verb Table. +**/ + UINT8 PchHdaVerbTableEntryNum; + +/** Offset 0x0357 +**/ + UINT8 UnusedUpdSpace13; + +/** Offset 0x0358 - PCH HDA Verb Table Pointer + Pointer to Array of pointers to Verb Table. +**/ + UINT32 PchHdaVerbTablePtr; + +/** Offset 0x035C - Enable HD Audio Link + Enable/disable HD Audio Link. Muxed with SSP0/SSP1/SNDW1. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkHda; + +/** Offset 0x035D - Enable HD Audio DMIC0 Link + Enable/disable HD Audio DMIC0 link. Muxed with SNDW4. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkDmic0; + +/** Offset 0x035E - Enable HD Audio DMIC1 Link + Enable/disable HD Audio DMIC1 link. Muxed with SNDW3. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkDmic1; + +/** Offset 0x035F - Enable HD Audio SSP0 Link + Enable/disable HD Audio SSP0/I2S link. Muxed with HDA. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSsp0; + +/** Offset 0x0360 - Enable HD Audio SSP1 Link + Enable/disable HD Audio SSP1/I2S link. Muxed with HDA/SNDW2. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSsp1; + +/** Offset 0x0361 - Enable HD Audio SSP2 Link + Enable/disable HD Audio SSP2/I2S link. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSsp2; + +/** Offset 0x0362 - Enable HD Audio SSP3 Link + Enable/disable HD Audio SSP3/I2S link. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSsp3; + +/** Offset 0x0363 - Enable HD Audio SSP4 Link + Enable/disable HD Audio SSP4/I2S link. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSsp4; + +/** Offset 0x0364 - Enable HD Audio SSP5 Link + Enable/disable HD Audio SSP5/I2S link. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSsp5; + +/** Offset 0x0365 - Enable HD Audio SoundWire#1 Link + Enable/disable HD Audio SNDW1 link. Muxed with HDA. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSndw1; + +/** Offset 0x0366 - Enable HD Audio SoundWire#2 Link + Enable/disable HD Audio SNDW2 link. Muxed with SSP1. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSndw2; + +/** Offset 0x0367 - Enable HD Audio SoundWire#3 Link + Enable/disable HD Audio SNDW3 link. Muxed with DMIC1. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSndw3; + +/** Offset 0x0368 - Enable HD Audio SoundWire#4 Link + Enable/disable HD Audio SNDW4 link. Muxed with DMIC0. + $EN_DIS +**/ + UINT8 PchHdaAudioLinkSndw4; + +/** Offset 0x0369 - CNVi Configuration + This option allows for automatic detection of Connectivity Solution. [Auto Detection] + assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi. + 0:Disable, 1:Auto +**/ + UINT8 CnviMode; + +/** Offset 0x036A - CNVi BT Core + Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE + $EN_DIS +**/ + UINT8 CnviBtCore; + +/** Offset 0x036B - CNVi BT Audio Offload + Enable/Disable BT Audio Offload, Default is DISABLE. 0: DISABLE, 1: ENABLE + $EN_DIS +**/ + UINT8 CnviBtAudioOffload; + +/** Offset 0x036C - CNVi RF_RESET pin muxing + Select CNVi RF_RESET# pin depending on board routing. ICP-LP: GPP_A8 = 0x2640E408(default) + or GPP_F4 = 0x1645E404. ICP-H: 0. ICP-N: GPP_H12 = 0x2746E40C(default) or GPP_H1 + = 0x3746E401. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h. +**/ + UINT32 CnviRfResetPinMux; + +/** Offset 0x0370 - CNVi CLKREQ pin muxing + Select CNVi CLKREQ pin depending on board routing. ICP-LP: GPP_A9 = 0x2640E609(default) + or GPP_F5 = 0x2645E605. ICP-H: 0. ICP-N: GPP_H13 = 0x2746E60D(default) or GPP_H2 + = 0x3746E602. Refer to GPIO_*_MUXING_CNVI_MODEM_CLKREQ_* in GpioPins*.h. +**/ + UINT32 CnviClkreqPinMux; + +/** Offset 0x0374 - Espi Lgmr Memory Range decode + This option enables or disables espi lgmr + $EN_DIS +**/ + UINT8 PchEspiLgmrEnable; + +/** Offset 0x0375 - PCH eSPI Master and Slave BME enabled + PCH eSPI Master and Slave BME enabled + $EN_DIS +**/ + UINT8 PchEspiBmeMasterSlaveEnabled; + +/** Offset 0x0376 - Enable Host C10 reporting through eSPI + Enable/disable Host C10 reporting to Slave via eSPI Virtual Wire. + $EN_DIS +**/ + UINT8 PchEspiHostC10ReportEnable; + +/** Offset 0x0377 - Enable SdCard Controller + Enable/disable SD Card Controller. + $EN_DIS +**/ + UINT8 ScsSdCardEnabled; + +/** Offset 0x0378 - SdCard power enable polarity + Choose SD_PWREN# polarity + 0: Active low, 1: Active high +**/ + UINT8 SdCardPowerEnableActiveHigh; + +/** Offset 0x0379 - Use tuned DLL values from policy + Set if FSP should use HS400 DLL values from policy + $EN_DIS +**/ + UINT8 SdCardUseCustomDlls; + +/** Offset 0x037A +**/ + UINT8 UnusedUpdSpace14[2]; + +/** Offset 0x037C - SdCard Tx CMD Delay control register value + Please see Tx CMD Delay Control register definition for help +**/ + UINT32 SdCardTxCmdDelayRegValue; + +/** Offset 0x0380 - SdCard Tx DATA Delay control 1 register value + Please see Tx DATA Delay control 1 register definition for help +**/ + UINT32 SdCardTxDataDelay1RegValue; + +/** Offset 0x0384 - SdCard Tx DATA Delay control 2 register value + Please see Tx DATA Delay control 2 register definition for help +**/ + UINT32 SdCardTxDataDelay2RegValue; + +/** Offset 0x0388 - SdCard Rx CMD + DATA Delay control 1 register value + Please see Rx CMD + DATA Delay control 1 register definition for help +**/ + UINT32 SdCardRxCmdDataDelay1RegValue; + +/** Offset 0x038C - SdCard Rx CMD + DATA Delay control 2 register value + Please see Rx CMD + DATA Delay control 2 register definition for help +**/ + UINT32 SdCardRxCmdDataDelay2RegValue; + +/** Offset 0x0390 - Enable eMMC Controller + Enable/disable eMMC Controller. + $EN_DIS +**/ + UINT8 ScsEmmcEnabled; + +/** Offset 0x0391 - Enable eMMC HS400 Mode + Enable eMMC HS400 Mode. + $EN_DIS +**/ + UINT8 ScsEmmcHs400Enabled; + +/** Offset 0x0392 - Use DLL values from policy + Set if FSP should use HS400 DLL values from policy + $EN_DIS +**/ + UINT8 EmmcUseCustomDlls; + +/** Offset 0x0393 +**/ + UINT8 UnusedUpdSpace15; + +/** Offset 0x0394 - Emmc Tx CMD Delay control register value + Please see Tx CMD Delay Control register definition for help +**/ + UINT32 EmmcTxCmdDelayRegValue; + +/** Offset 0x0398 - Emmc Tx DATA Delay control 1 register value + Please see Tx DATA Delay control 1 register definition for help +**/ + UINT32 EmmcTxDataDelay1RegValue; + +/** Offset 0x039C - Emmc Tx DATA Delay control 2 register value + Please see Tx DATA Delay control 2 register definition for help +**/ + UINT32 EmmcTxDataDelay2RegValue; + +/** Offset 0x03A0 - Emmc Rx CMD + DATA Delay control 1 register value + Please see Rx CMD + DATA Delay control 1 register definition for help +**/ + UINT32 EmmcRxCmdDataDelay1RegValue; + +/** Offset 0x03A4 - Emmc Rx CMD + DATA Delay control 2 register value + Please see Rx CMD + DATA Delay control 2 register definition for help +**/ + UINT32 EmmcRxCmdDataDelay2RegValue; + +/** Offset 0x03A8 - Emmc Rx Strobe Delay control register value + Please see Rx Strobe Delay control register definition for help +**/ + UINT32 EmmcRxStrobeDelayRegValue; + +/** Offset 0x03AC - UFS enable/disable + Please see Rx Strobe Delay control register definition for help + $EN_DIS +**/ + UINT8 UfsEnable[2]; + +/** Offset 0x03AE - Enable PCH ISH SPI GPIO pins assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshSpiGpioAssign; + +/** Offset 0x03AF - Enable PCH ISH UART0 GPIO pins assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshUart0GpioAssign; + +/** Offset 0x03B0 - Enable PCH ISH UART1 GPIO pins assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshUart1GpioAssign; + +/** Offset 0x03B1 - Enable PCH ISH I2C0 GPIO pins assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshI2c0GpioAssign; + +/** Offset 0x03B2 - Enable PCH ISH I2C1 GPIO pins assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshI2c1GpioAssign; + +/** Offset 0x03B3 - Enable PCH ISH I2C2 GPIO pins assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshI2c2GpioAssign; + +/** Offset 0x03B4 - Enable PCH ISH GP_0 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp0GpioAssign; + +/** Offset 0x03B5 - Enable PCH ISH GP_1 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp1GpioAssign; + +/** Offset 0x03B6 - Enable PCH ISH GP_2 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp2GpioAssign; + +/** Offset 0x03B7 - Enable PCH ISH GP_3 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp3GpioAssign; + +/** Offset 0x03B8 - Enable PCH ISH GP_4 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp4GpioAssign; + +/** Offset 0x03B9 - Enable PCH ISH GP_5 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp5GpioAssign; + +/** Offset 0x03BA - Enable PCH ISH GP_6 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp6GpioAssign; + +/** Offset 0x03BB - Enable PCH ISH GP_7 GPIO pin assigned + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIshGp7GpioAssign; + +/** Offset 0x03BC - PCH ISH PDT Unlock Msg + 0: False; 1: True. + $EN_DIS +**/ + UINT8 PchIshPdtUnlock; + +/** Offset 0x03BD - Enable SATA + Enable/disable SATA controller. + $EN_DIS +**/ + UINT8 SataEnable; + +/** Offset 0x03BE - PCH Sata Test Mode + Allow entrance to the PCH SATA test modes. + $EN_DIS +**/ + UINT8 SataTestMode; + +/** Offset 0x03BF - Enable SATA SALP Support + Enable/disable SATA Aggressive Link Power Management. + $EN_DIS +**/ + UINT8 SataSalpSupport; + +/** Offset 0x03C0 - PCH Sata Pwr Opt Enable + SATA Power Optimizer on PCH side. + $EN_DIS +**/ + UINT8 SataPwrOptEnable; + +/** Offset 0x03C1 - PCH Sata eSATA Speed Limit + When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed. + $EN_DIS +**/ + UINT8 EsataSpeedLimit; + +/** Offset 0x03C2 - SATA LED + SATA LED indicating SATA controller activity. 0: disable, 1: enable + $EN_DIS +**/ + UINT8 SataLedEnable; + +/** Offset 0x03C3 - SATA Mode + Select SATA controller working mode. + 0:AHCI, 1:RAID +**/ + UINT8 SataMode; + +/** Offset 0x03C4 - PCH Sata Speed Limit + Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault. +**/ + UINT8 SataSpeedLimit; + +/** Offset 0x03C5 - Enable SATA ports + Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1, + and so on. +**/ + UINT8 SataPortsEnable[8]; + +/** Offset 0x03CD - Enable SATA Port HotPlug + Enable SATA Port HotPlug. +**/ + UINT8 SataPortsHotPlug[8]; + +/** Offset 0x03D5 - Enable SATA Port Interlock Sw + Enable SATA Port Interlock Sw. +**/ + UINT8 SataPortsInterlockSw[8]; + +/** Offset 0x03DD - Enable SATA Port External + Enable SATA Port External. +**/ + UINT8 SataPortsExternal[8]; + +/** Offset 0x03E5 - Enable SATA Port SpinUp + Enable the COMRESET initialization Sequence to the device. +**/ + UINT8 SataPortsSpinUp[8]; + +/** Offset 0x03ED - Enable SATA Port Solid State Drive + 0: HDD; 1: SSD. +**/ + UINT8 SataPortsSolidStateDrive[8]; + +/** Offset 0x03F5 - Enable SATA DEVSLP Feature + Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each + port, byte0 for port0, byte1 for port1, and so on. +**/ + UINT8 SataPortsDevSlp[8]; + +/** Offset 0x03FD - Enable SATA Port Enable Dito Config + Enable DEVSLP Idle Timeout settings (DmVal, DitoVal). +**/ + UINT8 SataPortsEnableDitoConfig[8]; + +/** Offset 0x0405 - Enable SATA Port DmVal + DITO multiplier. Default is 15. +**/ + UINT8 SataPortsDmVal[8]; + +/** Offset 0x040D +**/ + UINT8 UnusedUpdSpace16[1]; + +/** Offset 0x040E - Enable SATA Port DmVal + DEVSLP Idle Timeout (DITO), Default is 625. +**/ + UINT16 SataPortsDitoVal[8]; + +/** Offset 0x041E - Enable SATA Port ZpOdd + Support zero power ODD. +**/ + UINT8 SataPortsZpOdd[8]; + +/** Offset 0x0426 - PCH Sata Rst Raid Alternate Id + Enable RAID Alternate ID. + $EN_DIS +**/ + UINT8 SataRstRaidDeviceId; + +/** Offset 0x0427 - PCH Sata Rst Raid0 + RAID0. + $EN_DIS +**/ + UINT8 SataRstRaid0; + +/** Offset 0x0428 - PCH Sata Rst Raid1 + RAID1. + $EN_DIS +**/ + UINT8 SataRstRaid1; + +/** Offset 0x0429 - PCH Sata Rst Raid10 + RAID10. + $EN_DIS +**/ + UINT8 SataRstRaid10; + +/** Offset 0x042A - PCH Sata Rst Raid5 + RAID5. + $EN_DIS +**/ + UINT8 SataRstRaid5; + +/** Offset 0x042B - PCH Sata Rst Irrt + Intel Rapid Recovery Technology. + $EN_DIS +**/ + UINT8 SataRstIrrt; + +/** Offset 0x042C - PCH Sata Rst Orom Ui Banner + OROM UI and BANNER. + $EN_DIS +**/ + UINT8 SataRstOromUiBanner; + +/** Offset 0x042D - PCH Sata Rst Orom Ui Delay + 00b: 2 secs; 01b: 4 secs; 10b: 6 secs; 11: 8 secs (see: PCH_SATA_OROM_DELAY). +**/ + UINT8 SataRstOromUiDelay; + +/** Offset 0x042E - PCH Sata Rst Hdd Unlock + Indicates that the HDD password unlock in the OS is enabled. + $EN_DIS +**/ + UINT8 SataRstHddUnlock; + +/** Offset 0x042F - PCH Sata Rst Led Locate + Indicates that the LED/SGPIO hardware is attached and ping to locate feature is + enabled on the OS. + $EN_DIS +**/ + UINT8 SataRstLedLocate; + +/** Offset 0x0430 - PCH Sata Rst Irrt Only + Allow only IRRT drives to span internal and external ports. + $EN_DIS +**/ + UINT8 SataRstIrrtOnly; + +/** Offset 0x0431 - PCH Sata Rst Smart Storage + RST Smart Storage caching Bit. + $EN_DIS +**/ + UINT8 SataRstSmartStorage; + +/** Offset 0x0432 - SATA RST Interrupt Mode + Allowes to choose which interrupts will be implemented by SATA controller in RAID mode. + 0:Msix, 1:Msi, 2:Legacy +**/ + UINT8 SataRstInterrupt; + +/** Offset 0x0433 - PCH Sata Rst Optane Memory + Optane Memory + $EN_DIS +**/ + UINT8 SataRstOptaneMemory; + +/** Offset 0x0434 - PCH SATA use RST Legacy OROM + Use PCH SATA RST Legacy OROM when CSM is Enabled + $EN_DIS +**/ + UINT8 SataRstLegacyOrom; + +/** Offset 0x0435 - PCH Sata Rst CPU Attached Storage + CPU Attached Storage + $EN_DIS +**/ + UINT8 SataRstCpuAttachedStorage; + +/** Offset 0x0436 - PCH Sata Rst Pcie Storage Remap enable + Enable Intel RST for PCIe Storage remapping. +**/ + UINT8 SataRstPcieEnable[3]; + +/** Offset 0x0439 - PCH Sata Rst Pcie Storage Port + Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect). +**/ + UINT8 SataRstPcieStoragePort[3]; + +/** Offset 0x043C - PCH Sata Rst Pcie Device Reset Delay + PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms +**/ + UINT8 SataRstPcieDeviceResetDelay[3]; + +/** Offset 0x043F - Port 0 T1 Multipler + Port 0 T1 Multipler. +**/ + UINT8 SataP0T1M; + +/** Offset 0x0440 - Port 0 T2 Multipler + Port 0 T2 Multipler. +**/ + UINT8 SataP0T2M; + +/** Offset 0x0441 - Port 0 T3 Multipler + Port 0 T3 Multipler. +**/ + UINT8 SataP0T3M; + +/** Offset 0x0442 - Port 0 Tdispatch + Port 0 Tdispatch. +**/ + UINT8 SataP0TDisp; + +/** Offset 0x0443 - Port 1 T1 Multipler + Port 1 T1 Multipler. +**/ + UINT8 SataP1T1M; + +/** Offset 0x0444 - Port 1 T2 Multipler + Port 1 T2 Multipler. +**/ + UINT8 SataP1T2M; + +/** Offset 0x0445 - Port 1 T3 Multipler + Port 1 T3 Multipler. +**/ + UINT8 SataP1T3M; + +/** Offset 0x0446 - Port 1 Tdispatch + Port 1 Tdispatch. +**/ + UINT8 SataP1TDisp; + +/** Offset 0x0447 - Port 0 Tinactive + Port 0 Tinactive. +**/ + UINT8 SataP0Tinact; + +/** Offset 0x0448 - Port 0 Alternate Fast Init Tdispatch + Port 0 Alternate Fast Init Tdispatch. + $EN_DIS +**/ + UINT8 SataP0TDispFinit; + +/** Offset 0x0449 - Port 1 Tinactive + Port 1 Tinactive. +**/ + UINT8 SataP1Tinact; + +/** Offset 0x044A - Port 1 Alternate Fast Init Tdispatch + Port 1 Alternate Fast Init Tdispatch. + $EN_DIS +**/ + UINT8 SataP1TDispFinit; + +/** Offset 0x044B - Sata Thermal Throttling Suggested Setting + Sata Thermal Throttling Suggested Setting. + $EN_DIS +**/ + UINT8 SataThermalSuggestedSetting; + +/** Offset 0x044C - Enable xHCI Compliance Mode + Compliance Mode can be enabled for testing through this option but this is disabled + by default. + $EN_DIS +**/ + UINT8 PchEnableComplianceMode; + +/** Offset 0x044D - USB PDO Programming + Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming + during later phase. 1: enable, 0: disable + $EN_DIS +**/ + UINT8 UsbPdoProgramming; + +/** Offset 0x044E - USB Overcurrent Override for DbC + This option overrides USB Over Current enablement state that USB OC will be disabled + after enabling this option. Enable when DbC is used to avoid signaling conflicts. + $EN_DIS +**/ + UINT8 PchEnableDbcObs; + +/** Offset 0x044F - PCH USB OverCurrent mapping lock enable + If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning + that OC mapping data will be consumed by xHCI and OC mapping registers will be locked. + $EN_DIS +**/ + UINT8 PchXhciOcLock; + +/** Offset 0x0450 - Enable USB2 ports + Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for + port1, and so on. +**/ + UINT8 PortUsb20Enable[16]; + +/** Offset 0x0460 - USB2 Port Over Current Pin + Describe the specific over current pin number of USB 2.0 Port N. +**/ + UINT8 Usb2OverCurrentPin[16]; + +/** Offset 0x0470 - Enable USB3 ports + Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for + port1, and so on. +**/ + UINT8 PortUsb30Enable[10]; + +/** Offset 0x047A - USB3 Port Over Current Pin + Describe the specific over current pin number of USB 3.0 Port N. +**/ + UINT8 Usb3OverCurrentPin[10]; + +/** Offset 0x0484 - Enable xDCI controller + Enable/disable to xDCI controller. + $EN_DIS +**/ + UINT8 XdciEnable; + +/** Offset 0x0485 - USB Per Port HS Preemphasis Bias + USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV, + 100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port. +**/ + UINT8 Usb2PhyPetxiset[16]; + +/** Offset 0x0495 - USB Per Port HS Transmitter Bias + USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV, + 100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port. +**/ + UINT8 Usb2PhyTxiset[16]; + +/** Offset 0x04A5 - USB Per Port HS Transmitter Emphasis + USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON, + 10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port. +**/ + UINT8 Usb2PhyPredeemp[16]; + +/** Offset 0x04B5 - USB Per Port Half Bit Pre-emphasis + USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis. + One byte for each port. +**/ + UINT8 Usb2PhyPehalfbit[16]; + +/** Offset 0x04C5 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment + Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value + in arrary can be between 0-1. One byte for each port. +**/ + UINT8 Usb3HsioTxDeEmphEnable[10]; + +/** Offset 0x04CF - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting + USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16], + Default = 29h (approximately -3.5dB De-Emphasis). One byte for each port. +**/ + UINT8 Usb3HsioTxDeEmph[10]; + +/** Offset 0x04D9 - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment + Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value + in arrary can be between 0-1. One byte for each port. +**/ + UINT8 Usb3HsioTxDownscaleAmpEnable[10]; + +/** Offset 0x04E3 - USB 3.0 TX Output Downscale Amplitude Adjustment + USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], Default + = 00h. One byte for each port. +**/ + UINT8 Usb3HsioTxDownscaleAmp[10]; + +/** Offset 0x04ED +**/ + UINT8 PchUsb3HsioCtrlAdaptOffsetCfgEnable[10]; + +/** Offset 0x04F7 +**/ + UINT8 PchUsb3HsioFilterSelNEnable[10]; + +/** Offset 0x0501 +**/ + UINT8 PchUsb3HsioFilterSelPEnable[10]; + +/** Offset 0x050B +**/ + UINT8 PchUsb3HsioOlfpsCfgPullUpDwnResEnable[10]; + +/** Offset 0x0515 +**/ + UINT8 PchUsb3HsioCtrlAdaptOffsetCfg[10]; + +/** Offset 0x051F +**/ + UINT8 PchUsb3HsioOlfpsCfgPullUpDwnRes[10]; + +/** Offset 0x0529 +**/ + UINT8 PchUsb3HsioFilterSelN[10]; + +/** Offset 0x0533 +**/ + UINT8 PchUsb3HsioFilterSelP[10]; + +/** Offset 0x053D - Enable PCIE RP HotPlug + Indicate whether the root port is hot plug available. +**/ + UINT8 PcieRpHotPlug[24]; + +/** Offset 0x0555 - Enable PCIE RP Pm Sci + Indicate whether the root port power manager SCI is enabled. +**/ + UINT8 PcieRpPmSci[24]; + +/** Offset 0x056D - Enable PCIE RP Transmitter Half Swing + Indicate whether the Transmitter Half Swing is enabled. +**/ + UINT8 PcieRpTransmitterHalfSwing[24]; + +/** Offset 0x0585 - Enable PCIE RP Clk Req Detect + Probe CLKREQ# signal before enabling CLKREQ# based power management. +**/ + UINT8 PcieRpClkReqDetect[24]; + +/** Offset 0x059D - PCIE RP Advanced Error Report + Indicate whether the Advanced Error Reporting is enabled. +**/ + UINT8 PcieRpAdvancedErrorReporting[24]; + +/** Offset 0x05B5 - PCIE RP Unsupported Request Report + Indicate whether the Unsupported Request Report is enabled. +**/ + UINT8 PcieRpUnsupportedRequestReport[24]; + +/** Offset 0x05CD - PCIE RP Fatal Error Report + Indicate whether the Fatal Error Report is enabled. +**/ + UINT8 PcieRpFatalErrorReport[24]; + +/** Offset 0x05E5 - PCIE RP No Fatal Error Report + Indicate whether the No Fatal Error Report is enabled. +**/ + UINT8 PcieRpNoFatalErrorReport[24]; + +/** Offset 0x05FD - PCIE RP Correctable Error Report + Indicate whether the Correctable Error Report is enabled. +**/ + UINT8 PcieRpCorrectableErrorReport[24]; + +/** Offset 0x0615 - PCIE RP System Error On Fatal Error + Indicate whether the System Error on Fatal Error is enabled. +**/ + UINT8 PcieRpSystemErrorOnFatalError[24]; + +/** Offset 0x062D - PCIE RP System Error On Non Fatal Error + Indicate whether the System Error on Non Fatal Error is enabled. +**/ + UINT8 PcieRpSystemErrorOnNonFatalError[24]; + +/** Offset 0x0645 - PCIE RP System Error On Correctable Error + Indicate whether the System Error on Correctable Error is enabled. +**/ + UINT8 PcieRpSystemErrorOnCorrectableError[24]; + +/** Offset 0x065D - PCIE RP Max Payload + Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD. +**/ + UINT8 PcieRpMaxPayload[24]; + +/** Offset 0x0675 +**/ + UINT8 UnusedUpdSpace17[3]; + +/** Offset 0x0678 - DPC for PCIE RP Mask + Enable/disable Downstream Port Containment for PCIE Root Ports. 0: disable, 1: enable. + One bit for each port, bit0 for port1, bit1 for port2, and so on. +**/ + UINT32 PcieRpDpcMask; + +/** Offset 0x067C - DPC Extensions PCIE RP Mask + Enable/disable DPC Extensions for PCIE Root Ports. 0: disable, 1: enable. One bit + for each port, bit0 for port1, bit1 for port2, and so on. +**/ + UINT32 PcieRpDpcExtensionsMask; + +/** Offset 0x0680 - PTM for PCIE RP Mask + Enable/disable Precision Time Measurement for PCIE Root Ports. 0: disable, 1: enable. + One bit for each port, bit0 for port1, bit1 for port2, and so on. +**/ + UINT32 PcieRpPtmMask; + +/** Offset 0x0684 - PCIE RP Pcie Speed + Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3 (see: + PCH_PCIE_SPEED). +**/ + UINT8 PcieRpPcieSpeed[24]; + +/** Offset 0x069C - PCIE RP Gen3 Equalization Phase Method + PCIe Gen3 Eq Ph3 Method (see PCH_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization; + 1: hardware equalization; 4: Fixed Coeficients. +**/ + UINT8 PcieRpGen3EqPh3Method[24]; + +/** Offset 0x06B4 - PCIE RP Physical Slot Number + Indicates the slot number for the root port. Default is the value as root port index. +**/ + UINT8 PcieRpPhysicalSlotNumber[24]; + +/** Offset 0x06CC - PCH PCIe root port connection type + 0: built-in device, 1:slot +**/ + UINT8 PcieRpSlotImplemented[24]; + +/** Offset 0x06E4 - PCIE RP Completion Timeout + The root port completion timeout(see: PCH_PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default. +**/ + UINT8 PcieRpCompletionTimeout[24]; + +/** Offset 0x06FC - PCIE RP Aspm + The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is + PchPcieAspmAutoConfig. +**/ + UINT8 PcieRpAspm[24]; + +/** Offset 0x0714 - PCIE RP L1 Substates + The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL). + Default is PchPcieL1SubstatesL1_1_2. +**/ + UINT8 PcieRpL1Substates[24]; + +/** Offset 0x072C - PCIE RP Ltr Enable + Latency Tolerance Reporting Mechanism. +**/ + UINT8 PcieRpLtrEnable[24]; + +/** Offset 0x0744 - PCIE RP Ltr Config Lock + 0: Disable; 1: Enable. +**/ + UINT8 PcieRpLtrConfigLock[24]; + +/** Offset 0x075C - PCIE RP Access Control Services Extended Capability + Enable/Disable PCIE RP Access Control Services Extended Capability +**/ + UINT8 PcieRpAcsEnabled[24]; + +/** Offset 0x0774 - PCIE RP Clock Power Management + Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal + can still be controlled by L1 PM substates mechanism +**/ + UINT8 PcieRpEnableCpm[24]; + +/** Offset 0x078C - PCIE RP Detect Timeout Ms + The number of milliseconds within 0~65535 in reference code will wait for link to + exit Detect state for enabled ports before assuming there is no device and potentially + disabling the port. +**/ + UINT16 PcieRpDetectTimeoutMs[24]; + +/** Offset 0x07BC - PCIE RP Ltr Max Snoop Latency + Latency Tolerance Reporting, Max Snoop Latency. +**/ + UINT16 PcieRpLtrMaxSnoopLatency[24]; + +/** Offset 0x07EC - PCIE RP Ltr Max No Snoop Latency + Latency Tolerance Reporting, Max Non-Snoop Latency. +**/ + UINT16 PcieRpLtrMaxNoSnoopLatency[24]; + +/** Offset 0x081C - PCIE RP Snoop Latency Override Mode + Latency Tolerance Reporting, Snoop Latency Override Mode. +**/ + UINT8 PcieRpSnoopLatencyOverrideMode[24]; + +/** Offset 0x0834 - PCIE RP Snoop Latency Override Multiplier + Latency Tolerance Reporting, Snoop Latency Override Multiplier. +**/ + UINT8 PcieRpSnoopLatencyOverrideMultiplier[24]; + +/** Offset 0x084C - PCIE RP Snoop Latency Override Value + Latency Tolerance Reporting, Snoop Latency Override Value. +**/ + UINT16 PcieRpSnoopLatencyOverrideValue[24]; + +/** Offset 0x087C - PCIE RP Non Snoop Latency Override Mode + Latency Tolerance Reporting, Non-Snoop Latency Override Mode. +**/ + UINT8 PcieRpNonSnoopLatencyOverrideMode[24]; + +/** Offset 0x0894 - PCIE RP Non Snoop Latency Override Multiplier + Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier. +**/ + UINT8 PcieRpNonSnoopLatencyOverrideMultiplier[24]; + +/** Offset 0x08AC - PCIE RP Non Snoop Latency Override Value + Latency Tolerance Reporting, Non-Snoop Latency Override Value. +**/ + UINT16 PcieRpNonSnoopLatencyOverrideValue[24]; + +/** Offset 0x08DC - PCIE RP Slot Power Limit Scale + Specifies scale used for slot power limit value. Leave as 0 to set to default. +**/ + UINT8 PcieRpSlotPowerLimitScale[24]; + +/** Offset 0x08F4 - PCIE RP Slot Power Limit Value + Specifies upper limit on power supplie by slot. Leave as 0 to set to default. +**/ + UINT16 PcieRpSlotPowerLimitValue[24]; + +/** Offset 0x0924 - PCIE RP Upstream Port Transmiter Preset + Used during Gen3 Link Equalization. Used for all lanes. Default is 5. +**/ + UINT8 PcieRpUptp[24]; + +/** Offset 0x093C - PCIE RP Downstream Port Transmiter Preset + Used during Gen3 Link Equalization. Used for all lanes. Default is 7. +**/ + UINT8 PcieRpDptp[24]; + +/** Offset 0x0954 - Usage type for ClkSrc + 0-23: PCH rootport, 0x40-0x43: PEG port, 0x70:LAN, 0x80: unspecified but in use + (free running), 0xFF: not used +**/ + UINT8 PcieClkSrcUsage[16]; + +/** Offset 0x0964 - ClkReq-to-ClkSrc mapping + Number of ClkReq signal assigned to ClkSrc +**/ + UINT8 PcieClkSrcClkReq[16]; + +/** Offset 0x0974 - PCIE Eq Ph3 Lane Param Cm + PCH_PCIE_EQ_LANE_PARAM. Coefficient C-1. +**/ + UINT8 PcieEqPh3LaneParamCm[24]; + +/** Offset 0x098C - PCIE Eq Ph3 Lane Param Cp + PCH_PCIE_EQ_LANE_PARAM. Coefficient C+1. +**/ + UINT8 PcieEqPh3LaneParamCp[24]; + +/** Offset 0x09A4 - PCIE Sw Eq CoeffList Cm + PCH_PCIE_EQ_PARAM. Coefficient C-1. +**/ + UINT8 PcieSwEqCoeffListCm[5]; + +/** Offset 0x09A9 - PCIE Sw Eq CoeffList Cp + PCH_PCIE_EQ_PARAM. Coefficient C+1. +**/ + UINT8 PcieSwEqCoeffListCp[5]; + +/** Offset 0x09AE - PCIE RP Enable Port8xh Decode + This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable; + 1: Enable. + $EN_DIS +**/ + UINT8 PcieEnablePort8xhDecode; + +/** Offset 0x09AF - PCIE Port8xh Decode Port Index + The Index of PCIe Port that is selected for Port8xh Decode (0 Based). +**/ + UINT8 PchPciePort8xhDecodePortIndex; + +/** Offset 0x09B0 - PCIE Enable Peer Memory Write + This member describes whether Peer Memory Writes are enabled on the platform. + $EN_DIS +**/ + UINT8 PcieEnablePeerMemoryWrite; + +/** Offset 0x09B1 - PCIE Compliance Test Mode + Compliance Test Mode shall be enabled when using Compliance Load Board. + $EN_DIS +**/ + UINT8 PcieComplianceTestMode; + +/** Offset 0x09B2 - PCIE Rp Function Swap + Allows BIOS to use root port function number swapping when root port of function + 0 is disabled. + $EN_DIS +**/ + UINT8 PcieRpFunctionSwap; + +/** Offset 0x09B3 - Number of DevIntConfig Entry + Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr + must not be NULL. +**/ + UINT8 NumOfDevIntConfig; + +/** Offset 0x09B4 - Address of PCH_DEVICE_INTERRUPT_CONFIG table. + The address of the table of PCH_DEVICE_INTERRUPT_CONFIG. +**/ + UINT32 DevIntConfigPtr; + +/** Offset 0x09B8 - PIRQx to IRQx Map Config + PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for + PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy + 8259 PCI mode. +**/ + UINT8 PxRcConfig[8]; + +/** Offset 0x09C0 - Select GPIO IRQ Route + GPIO IRQ Select. The valid value is 14 or 15. +**/ + UINT8 GpioIrqRoute; + +/** Offset 0x09C1 - Select SciIrqSelect + SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only. +**/ + UINT8 SciIrqSelect; + +/** Offset 0x09C2 - Select TcoIrqSelect + TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23. +**/ + UINT8 TcoIrqSelect; + +/** Offset 0x09C3 - Enable/Disable Tco IRQ + Enable/disable TCO IRQ + $EN_DIS +**/ + UINT8 TcoIrqEnable; + +/** Offset 0x09C4 - Enable LOCKDOWN SMI + Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit. + $EN_DIS +**/ + UINT8 PchLockDownGlobalSmi; + +/** Offset 0x09C5 - Enable LOCKDOWN BIOS Interface + Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register. + $EN_DIS +**/ + UINT8 PchLockDownBiosInterface; + +/** Offset 0x09C6 - Enable LOCKDOWN BIOS LOCK + Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region + protection. + $EN_DIS +**/ + UINT8 PchLockDownBiosLock; + +/** Offset 0x09C7 - RTC CMOS MEMORY LOCK + Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper + and and lower 128-byte bank of RTC RAM. + $EN_DIS +**/ + UINT8 PchLockDownRtcMemoryLock; + +/** Offset 0x09C8 - Unlock all GPIO pads + Force all GPIO pads to be unlocked for debug purpose. + $EN_DIS +**/ + UINT8 PchUnlockGpioPads; + +/** Offset 0x09C9 - Enable Power Optimizer + Enable DMI Power Optimizer on PCH side. + $EN_DIS +**/ + UINT8 PchPwrOptEnable; + +/** Offset 0x09CA - Pch Dmi Aspm Ctrl + ASPM configuration on the PCH side of the DMI/OPI Link. Default is PchPcieAspmAutoConfig + 0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto +**/ + UINT8 PchDmiAspmCtrl; + +/** Offset 0x09CB - PCH Flash Protection Ranges Write Enble + Write or erase is blocked by hardware. +**/ + UINT8 PchWriteProtectionEnable[5]; + +/** Offset 0x09D0 - PCH Flash Protection Ranges Read Enble + Read is blocked by hardware. +**/ + UINT8 PchReadProtectionEnable[5]; + +/** Offset 0x09D5 +**/ + UINT8 UnusedUpdSpace18[1]; + +/** Offset 0x09D6 - PCH Protect Range Limit + Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for + limit comparison. +**/ + UINT16 PchProtectedRangeLimit[5]; + +/** Offset 0x09E0 - PCH Protect Range Base + Left shifted address by 12 bits with address bits 11:0 are assumed to be 0. +**/ + UINT16 PchProtectedRangeBase[5]; + +/** Offset 0x09EA - Enable PCH Io Apic Entry 24-119 + 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PchIoApicEntry24_119; + +/** Offset 0x09EB - Enable 8254 Static Clock Gating + Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time + might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support + legacy OS using 8254 timer. Also enable this while S0ix is enabled. + $EN_DIS +**/ + UINT8 Enable8254ClockGating; + +/** Offset 0x09EC - Enable 8254 Static Clock Gating On S3 + This is only applicable when Enable8254ClockGating is disabled. FSP will do the + 8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This + avoids the SMI requirement for the programming. + $EN_DIS +**/ + UINT8 Enable8254ClockGatingOnS3; + +/** Offset 0x09ED - PCH Io Apic ID + This member determines IOAPIC ID. Default is 0x02. +**/ + UINT8 PchIoApicId; + +/** Offset 0x09EE - PCH Unlock SideBand access + The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before + 3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access. + $EN_DIS +**/ + UINT8 PchSbAccessUnlock; + +/** Offset 0x09EF - PCH Compatibility Revision ID + This member describes whether or not the CRID feature of PCH should be enabled. + $EN_DIS +**/ + UINT8 PchCrid; + +/** Offset 0x09F0 - PCH Pm PME_B0_S5_DIS + When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1. + $EN_DIS +**/ + UINT8 PchPmPmeB0S5Dis; + +/** Offset 0x09F1 - PCH Pm Wol Enable Override + Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register. + $EN_DIS +**/ + UINT8 PchPmWolEnableOverride; + +/** Offset 0x09F2 - PCH Pm Pcie Wake From DeepSx + Determine if enable PCIe to wake from deep Sx. + $EN_DIS +**/ + UINT8 PchPmPcieWakeFromDeepSx; + +/** Offset 0x09F3 - PCH Pm WoW lan Enable + Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register. + $EN_DIS +**/ + UINT8 PchPmWoWlanEnable; + +/** Offset 0x09F4 - PCH Pm WoW lan DeepSx Enable + Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the + PWRM_CFG3 register. + $EN_DIS +**/ + UINT8 PchPmWoWlanDeepSxEnable; + +/** Offset 0x09F5 - PCH Pm Lan Wake From DeepSx + Determine if enable LAN to wake from deep Sx. + $EN_DIS +**/ + UINT8 PchPmLanWakeFromDeepSx; + +/** Offset 0x09F6 - PCH Pm Deep Sx Pol + Deep Sx Policy. + $EN_DIS +**/ + UINT8 PchPmDeepSxPol; + +/** Offset 0x09F7 - PCH Pm Slp S3 Min Assert + SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms. +**/ + UINT8 PchPmSlpS3MinAssert; + +/** Offset 0x09F8 - PCH Pm Slp S4 Min Assert + SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s. +**/ + UINT8 PchPmSlpS4MinAssert; + +/** Offset 0x09F9 - PCH Pm Slp Sus Min Assert + SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s. +**/ + UINT8 PchPmSlpSusMinAssert; + +/** Offset 0x09FA - PCH Pm Slp A Min Assert + SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s. +**/ + UINT8 PchPmSlpAMinAssert; + +/** Offset 0x09FB - PCH Pm Slp Strch Sus Up + Enable SLP_X Stretching After SUS Well Power Up. + $EN_DIS +**/ + UINT8 PchPmSlpStrchSusUp; + +/** Offset 0x09FC - PCH Pm Slp Lan Low Dc + Enable/Disable SLP_LAN# Low on DC Power. + $EN_DIS +**/ + UINT8 PchPmSlpLanLowDc; + +/** Offset 0x09FD - PCH Pm Pwr Btn Override Period + PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s. +**/ + UINT8 PchPmPwrBtnOverridePeriod; + +/** Offset 0x09FE - PCH Energy Reporting + Disable/Enable PCH to CPU energy report feature. + $EN_DIS +**/ + UINT8 PchPmDisableEnergyReport; + +/** Offset 0x09FF - PCH Pm Disable Dsx Ac Present Pulldown + When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit. + $EN_DIS +**/ + UINT8 PchPmDisableDsxAcPresentPulldown; + +/** Offset 0x0A00 - PCH Pm Disable Native Power Button + Power button native mode disable. + $EN_DIS +**/ + UINT8 PchPmDisableNativePowerButton; + +/** Offset 0x0A01 +**/ + UINT8 UnusedUpdSpace19[3]; + +/** Offset 0x0A04 - Power button debounce configuration + Debounce time for PWRBTN in microseconds. For values not supported by HW, they will + be rounded down to closest supported on. 0: disable, 250-1024000us: supported range +**/ + UINT32 PmcPowerButtonDebounceTime; + +/** Offset 0x0A08 - Disable Power Button debounce in PMC module + Disable Power Button debounce for PWRBTN in PMC module. '0': The 16ms debounce period + applies to all usages of the PWRBTN# pin (legacy behavior). '1': When a falling + edge occurs on the PWRBTN# pin, an interrupt is generated and the 16ms debounce + timer starts. Subsequent interrupts are masked while the debounce timer is running. +**/ + UINT8 PmcDisablePowerButtonDebounce; + +/** Offset 0x0A09 - PCH Pm Slp S0 Enable + Indicates whether SLP_S0# is to be asserted when PCH reaches idle state. + $EN_DIS +**/ + UINT8 PchPmSlpS0Enable; + +/** Offset 0x0A0A - PCH Pm ME_WAKE_STS + Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register. + $EN_DIS +**/ + UINT8 PchPmMeWakeSts; + +/** Offset 0x0A0B - PCH Pm WOL_OVR_WK_STS + Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register. + $EN_DIS +**/ + UINT8 PchPmWolOvrWkSts; + +/** Offset 0x0A0C - Enable TCO timer. + When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have + huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer + emulation must be enabled, and WDAT table must not be exposed to the OS. + $EN_DIS +**/ + UINT8 EnableTcoTimer; + +/** Offset 0x0A0D - VRAlert# Pin + When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling + to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable + $EN_DIS +**/ + UINT8 PchPmVrAlert; + +/** Offset 0x0A0E - PCH Pm Reset Power Cycle Duration + Could be customized in the unit of second. Please refer to EDS for all support settings. + 0 is default, 1 is 1 second, 2 is 2 seconds, ... +**/ + UINT8 PchPmPwrCycDur; + +/** Offset 0x0A0F - PCH Pm Pcie Pll Ssc + Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No + BIOS override. +**/ + UINT8 PchPmPciePllSsc; + +/** Offset 0x0A10 - S0i3 support + S0i3 platform support. When enabled ASL code is used to determine if platform can + go to S0i2 or S0i3 state. 0:Disable(S0i2 only), 1:Enable (Runtime in ASL) + $EN_DIS +**/ + UINT8 PchPmS0i3Support; + +/** Offset 0x0A11 - SLP_S0# Override + DEPRECATED + 0:Disabled, 1:Enabled +**/ + UINT8 SlpS0Override; + +/** Offset 0x0A12 - S0ix Override Settings + DEPRECATED + 0:No Change, 1:DCI OOB, 2:USB2 DbC +**/ + UINT8 SlpS0DisQForDebug; + +/** Offset 0x0A13 - PMC Debug Message Enable + When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW + will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix + $EN_DIS +**/ + UINT8 PmcDbgMsgEn; + +/** Offset 0x0A14 - Pointer of ChipsetInit format v2 Binary + ChipsetInit Binary format v2 Pointer. +**/ + UINT32 ChipsetInitBinPtr; + +/** Offset 0x0A18 - Length of ChipsetInit format v2 Binary + ChipsetInit Binary format v2 Length. +**/ + UINT32 ChipsetInitBinLen; + +/** Offset 0x0A1C - Enable PS_ON. + PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power + target that will be required by the California Energy Commission (CEC). When FALSE, + PS_ON is to be disabled. + $EN_DIS +**/ + UINT8 PsOnEnable; + +/** Offset 0x0A1D - Pmc Cpu C10 Gate Pin Enable + Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO + and VccSTG rails instead of SLP_S0# pin. + $EN_DIS +**/ + UINT8 PmcCpuC10GatePinEnable; + +/** Offset 0x0A1E - ModPHY SUS Power Domain Dynamic Gating + Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on + PCH-H. 0: disable, 1: enable + $EN_DIS +**/ + UINT8 PmcModPhySusPgEnable; + +/** Offset 0x0A1F - PCH USB2 PHY Power Gating enable + 1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY + Sus Well PG + $EN_DIS +**/ + UINT8 PmcUsb2PhySusPgEnable; + +/** Offset 0x0A20 - OS IDLE Mode Enable + Enable/Disable OS Idle Mode (PCH-N and PCH-H only) + $EN_DIS +**/ + UINT8 PmcOsIdleEnable; + +/** Offset 0x0A21 - Enable PMC CrashLog + Enable or Disable PMC CrashLog; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 PmcCrashLogEnable; + +/** Offset 0x0A22 - Enable CPPM Forced Alignment + Enable or Disable CPPM Forced Alignment; 0: Disable; 1: Enable. + $EN_DIS +**/ + UINT8 ForcedAlignmentEnable; + +/** Offset 0x0A23 - PCHHOT# pin + Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable + $EN_DIS +**/ + UINT8 PchHotEnable; + +/** Offset 0x0A24 - Thermal Throttling Custimized T0Level Value + Custimized T0Level value. +**/ + UINT16 PchT0Level; + +/** Offset 0x0A26 - Thermal Throttling Custimized T1Level Value + Custimized T1Level value. +**/ + UINT16 PchT1Level; + +/** Offset 0x0A28 - Thermal Throttling Custimized T2Level Value + Custimized T2Level value. +**/ + UINT16 PchT2Level; + +/** Offset 0x0A2A - Enable The Thermal Throttle + Enable the thermal throttle function. + $EN_DIS +**/ + UINT8 PchTTEnable; + +/** Offset 0x0A2B - PMSync State 13 + When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force + at least T2 state. + $EN_DIS +**/ + UINT8 PchTTState13Enable; + +/** Offset 0x0A2C - Thermal Throttle Lock + Thermal Throttle Lock. + $EN_DIS +**/ + UINT8 PchTTLock; + +/** Offset 0x0A2D - Thermal Throttling Suggested Setting + Thermal Throttling Suggested Setting. + $EN_DIS +**/ + UINT8 TTSuggestedSetting; + +/** Offset 0x0A2E - Enable PCH Cross Throttling + Enable/Disable PCH Cross Throttling + $EN_DIS +**/ + UINT8 TTCrossThrottling; + +/** Offset 0x0A2F - DMI Thermal Sensor Autonomous Width Enable + DMI Thermal Sensor Autonomous Width Enable. + $EN_DIS +**/ + UINT8 PchDmiTsawEn; + +/** Offset 0x0A30 - DMI Thermal Sensor Suggested Setting + DMT thermal sensor suggested representative values. + $EN_DIS +**/ + UINT8 DmiSuggestedSetting; + +/** Offset 0x0A31 - Thermal Sensor 0 Target Width + Thermal Sensor 0 Target Width. + 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 +**/ + UINT8 DmiTS0TW; + +/** Offset 0x0A32 - Thermal Sensor 1 Target Width + Thermal Sensor 1 Target Width. + 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 +**/ + UINT8 DmiTS1TW; + +/** Offset 0x0A33 - Thermal Sensor 2 Target Width + Thermal Sensor 2 Target Width. + 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 +**/ + UINT8 DmiTS2TW; + +/** Offset 0x0A34 - Thermal Sensor 3 Target Width + Thermal Sensor 3 Target Width. + 0:x1, 1:x2, 2:x4, 3:x8, 4:x16 +**/ + UINT8 DmiTS3TW; + +/** Offset 0x0A35 - Enable Memory Thermal Throttling + Enable Memory Thermal Throttling. + $EN_DIS +**/ + UINT8 PchMemoryThrottlingEnable; + +/** Offset 0x0A36 - Memory Thermal Throttling + Enable Memory Thermal Throttling. +**/ + UINT8 PchMemoryPmsyncEnable[2]; + +/** Offset 0x0A38 - Enable Memory Thermal Throttling + Enable Memory Thermal Throttling. +**/ + UINT8 PchMemoryC0TransmitEnable[2]; + +/** Offset 0x0A3A - Enable Memory Thermal Throttling + Enable Memory Thermal Throttling. +**/ + UINT8 PchMemoryPinSelection[2]; + +/** Offset 0x0A3C - Thermal Device Temperature + Decides the temperature. +**/ + UINT16 PchTemperatureHotLevel; + +/** Offset 0x0A3E - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states + Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5 +**/ + UINT8 PchFivrExtV1p05RailEnabledStates; + +/** Offset 0x0A3F +**/ + UINT8 UnusedUpdSpace20; + +/** Offset 0x0A40 - External V1P05 Voltage Value that will be used in S0i2/S0i3 states + Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...) +**/ + UINT16 PchFivrExtV1p05RailVoltage; + +/** Offset 0x0A42 - External V1P05 Icc Max Value + Granularity of this setting is 1mA and maximal possible value is 200mA +**/ + UINT8 PchFivrExtV1p05RailIccMax; + +/** Offset 0x0A43 - Mask to enable the usage of external Vnn VR rail in specific S0ix or Sx states + Enable External Vnn Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5 +**/ + UINT8 PchFivrExtVnnRailEnabledStates; + +/** Offset 0x0A44 - External Vnn Voltage Value that will be used in S0ix/Sx states + Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...) +**/ + UINT16 PchFivrExtVnnRailVoltage; + +/** Offset 0x0A46 - External Vnn Icc Max Value that will be used in S0ix/Sx states + Granularity of this setting is 1mA and maximal possible value is 200mA +**/ + UINT8 PchFivrExtVnnRailIccMax; + +/** Offset 0x0A47 - Mask to enable the usage of external Vnn VR rail in Sx states + Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in + Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT5:S5 +**/ + UINT8 PchFivrExtVnnRailSxEnabledStates; + +/** Offset 0x0A48 - External Vnn Voltage Value that will be used in Sx states + Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments + (0=0mV, 1=2.5mV, 2=5mV...) +**/ + UINT16 PchFivrExtVnnRailSxVoltage; + +/** Offset 0x0A4A - External Vnn Icc Max Value that will be used in Sx states + Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting + is 1mA and maximal possible value is 200mA +**/ + UINT8 PchFivrExtVnnRailSxIccMax; + +/** Offset 0x0A4B - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage + This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX + to low current mode voltage,for PCH-LP ICL U/Y board with D0 stepping need to program + it to 12us +**/ + UINT8 PchFivrVccinAuxLowToHighCurModeVolTranTime; + +/** Offset 0x0A4C - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage + This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX + to retention mode voltage. +**/ + UINT8 PchFivrVccinAuxRetToHighCurModeVolTranTime; + +/** Offset 0x0A4D - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage + This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX + to retention mode voltage. +**/ + UINT8 PchFivrVccinAuxRetToLowCurModeVolTranTime; + +/** Offset 0x0A4E - Transition time in microseconds from Off (0V) to High Current Mode Voltage + This field has 1us resolution. When value is 0 Transition to 0V is disabled,for + PCH-LP ICL U/Y board with D0 stepping need to program it to 120us +**/ + UINT16 PchFivrVccinAuxOffToHighCurModeVolTranTime; + +/** Offset 0x0A50 - FIVR Dynamic Power Management + Enable/Disable FIVR Dynamic Power Management. + $EN_DIS +**/ + UINT8 PchFivrDynPm; + +/** Offset 0x0A51 - Serial IO UART DBG2 table + Enable or disable Serial Io UART DBG2 table, default is Disable; 0: Disable; + 1: Enable. +**/ + UINT8 SerialIoUartDbg2[3]; + +/** Offset 0x0A54 - Trace Hub Memory Base + If Trace Hub is enabled and trace to memory is desired, BootLoader needs to allocate + trace hub memory as reserved and uncacheable, set the base to ensure Trace Hub + memory is configured properly. +**/ + UINT32 TraceHubMemBase; + +/** Offset 0x0A58 - ITSS IRQ Polarity. + Configuration for ITSS IPC[0-3] registers. +**/ + UINT32 ItssIrqPolarity[4]; + +/** Offset 0x0A68 - PCH PMC Energy Report Debug mode + Disable/Enable Energy Reporting Debug Mode. + $EN_DIS +**/ + UINT8 PchPmEnergyReportDebugMode; + +/** Offset 0x0A69 +**/ + UINT8 UnusedUpdSpace21[4]; + +/** Offset 0x0A6D +**/ + UINT8 ReservedFspsUpd[11]; +} FSP_S_CONFIG; /** Fsp S UPD Configuration **/ @@ -59,11 +3596,11 @@ typedef struct { **/ FSP_S_CONFIG FspsConfig; -/** Offset 0x07AD +/** Offset 0x0A78 **/ - FSP_S_TEST_CONFIG FspsTestConfig; + UINT8 UnusedUpdSpace22[6]; -/** Offset 0x0A80 +/** Offset 0x0A7E **/ UINT16 UpdTerminator; } FSPS_UPD; -- cgit v1.2.3