From 17c577153042b6559bf7a9dca6ae9f644b18d770 Mon Sep 17 00:00:00 2001 From: Vagiz Trakhanov Date: Thu, 28 Sep 2017 14:21:54 +0000 Subject: superio/ite/common: Add temperature offset MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add a devicetree option to set temperature adjustment registers required for thermal diode sensors and PECI. However, this commit does not have the code needed to make PECI interface actually use these registers. It only applies to diodes. As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3". PECI, apparently, takes precedence over diode, so the adjustment register will be set and PECI activated. Or simply use the followup patch, which makes THERMAL_PECI a mode like THERMAL_DIODE. I don't have hardware to test THERMAL_DIODE mode, but in case of PECI, without this patch I had about -60°C on idle. Now, with offset 97, which was taken from vendor bios, PECI readings became reasonable 35°C. TEST=Set a temperature offset, then ensure that the value you set is reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4 Signed-off-by: Vagiz Tarkhanov Reviewed-on: https://review.coreboot.org/21843 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber --- src/superio/ite/common/env_ctrl.c | 16 ++++++++++++---- src/superio/ite/common/env_ctrl.h | 20 ++++++++++++++++++++ src/superio/ite/common/env_ctrl_chip.h | 23 ++++++++++++++++------- 3 files changed, 48 insertions(+), 11 deletions(-) (limited to 'src/superio/ite/common') diff --git a/src/superio/ite/common/env_ctrl.c b/src/superio/ite/common/env_ctrl.c index 1e313ce715..c8274db6c8 100644 --- a/src/superio/ite/common/env_ctrl.c +++ b/src/superio/ite/common/env_ctrl.c @@ -99,13 +99,13 @@ static void enable_peci(const u16 base, const u8 tmpin) * into TMPINx register */ static void enable_tmpin(const u16 base, const u8 tmpin, - const enum ite_ec_thermal_mode mode) + const struct ite_ec_thermal_config *const conf) { u8 reg; reg = ite_ec_read(base, ITE_EC_ADC_TEMP_CHANNEL_ENABLE); - switch (mode) { + switch (conf->mode) { case THERMAL_DIODE: reg |= ITE_EC_ADC_TEMP_DIODE_MODE(tmpin); break; @@ -115,12 +115,20 @@ static void enable_tmpin(const u16 base, const u8 tmpin, default: printk(BIOS_WARNING, "Unsupported thermal mode 0x%x on TMPIN%d\n", - mode, tmpin); + conf->mode, tmpin); return; } ite_ec_write(base, ITE_EC_ADC_TEMP_CHANNEL_ENABLE, reg); + /* Set temperature offsets */ + if (conf->mode != THERMAL_RESISTOR) { + reg = ite_ec_read(base, ITE_EC_BEEP_ENABLE); + reg |= ITE_EC_TEMP_ADJUST_WRITE_ENABLE; + ite_ec_write(base, ITE_EC_BEEP_ENABLE, reg); + ite_ec_write(base, ITE_EC_TEMP_ADJUST[tmpin-1], conf->offset); + } + /* Enable the startup of monitoring operation */ reg = ite_ec_read(base, ITE_EC_CONFIGURATION); reg |= ITE_EC_CONFIGURATION_START; @@ -233,7 +241,7 @@ void ite_ec_init(const u16 base, const struct ite_ec_config *const conf) /* Enable HWM if configured */ for (i = 0; i < ITE_EC_TMPIN_CNT; ++i) - enable_tmpin(base, i + 1, conf->tmpin_mode[i]); + enable_tmpin(base, i + 1, &conf->tmpin[i]); /* Enable reading of voltage pins */ ite_ec_write(base, ITE_EC_ADC_VOLTAGE_CHANNEL_ENABLE, conf->vin_mask); diff --git a/src/superio/ite/common/env_ctrl.h b/src/superio/ite/common/env_ctrl.h index fa131166c0..1be6436310 100644 --- a/src/superio/ite/common/env_ctrl.h +++ b/src/superio/ite/common/env_ctrl.h @@ -93,6 +93,26 @@ #define ITE_EC_ADC_TEMP_DIODE_MODE(x) (1 << ((x)-1)) #define ITE_EC_ADC_TEMP_EXTRA_CHANNEL_ENABLE 0x55 +/* Matches length of ITE_EC_TMPIN_CNT */ +static const u8 ITE_EC_TEMP_ADJUST[] = { 0x56, 0x57, 0x59 }; + +#define ITE_EC_BEEP_ENABLE 0x5C +#define ITE_EC_TEMP_ADJUST_WRITE_ENABLE (1 << 7) +#define ITE_EC_ADC_CLOCK_1MHZ (6 << 4) +#define ITE_EC_ADC_CLOCK_2MHZ (7 << 4) +#define ITE_EC_ADC_CLOCK_24MHZ (5 << 4) +#define ITE_EC_ADC_CLOCK_31KHZ (4 << 4) +#define ITE_EC_ADC_CLOCK_62KHZ (3 << 4) +#define ITE_EC_ADC_CLOCK_125KHZ (2 << 4) +#define ITE_EC_ADC_CLOCK_250KHZ (1 << 4) +#define ITE_EC_ADC_CLOCK_500KHZ (0 << 4) +#define ITE_EC_BEEP_ON_TMP_LIMIT (1 << 2) +#define ITE_EC_BEEP_ON_VIN_LIMIT (1 << 1) +#define ITE_EC_BEEP_ON_FAN_LIMIT (1 << 0) +#define ITE_EC_BEEP_FREQ_DIV_OF_FAN 0x5D +#define ITE_EC_BEEP_FREQ_DIV_OF_VOLT 0x5E +#define ITE_EC_BEEP_FREQ_DIV_OF_TEMP 0x5F + #define ITE_EC_FAN_CTL_TEMP_LIMIT_OFF(x) (0x60 + ((x)-1) * 8) #define ITE_EC_FAN_CTL_TEMP_LIMIT_START(x) (0x61 + ((x)-1) * 8) #define ITE_EC_FAN_CTL_TEMP_LIMIT_FULL(x) (0x62 + ((x)-1) * 8) diff --git a/src/superio/ite/common/env_ctrl_chip.h b/src/superio/ite/common/env_ctrl_chip.h index f01c574d47..8eb908e77a 100644 --- a/src/superio/ite/common/env_ctrl_chip.h +++ b/src/superio/ite/common/env_ctrl_chip.h @@ -28,6 +28,12 @@ enum ite_ec_thermal_mode { THERMAL_RESISTOR, }; +struct ite_ec_thermal_config { + enum ite_ec_thermal_mode mode; + /* Offset is used for diode sensors and PECI */ + u8 offset; +}; + /* Bit mask for voltage pins VINx */ enum ite_ec_voltage_pin { VIN0 = 0x01, @@ -74,25 +80,28 @@ struct ite_ec_config { u8 peci_tmpin; /* - * Enable thermal mode on TMPINx. + * Enable reading of voltage pins VINx. */ - enum ite_ec_thermal_mode tmpin_mode[ITE_EC_TMPIN_CNT]; + enum ite_ec_voltage_pin vin_mask; /* - * Enable reading of voltage pins VINx. + * Enable temperature sensors in given mode. */ - enum ite_ec_voltage_pin vin_mask; + struct ite_ec_thermal_config tmpin[ITE_EC_TMPIN_CNT]; /* * Enable a FAN in given mode. */ struct ite_ec_fan_config fan[ITE_EC_FAN_CNT]; + + /* FIXME: enable beep when exceeding TMPIN, VIN, FAN limits */ }; /* Some shorthands for device trees */ -#define TMPIN1 ec.tmpin_mode[0] -#define TMPIN2 ec.tmpin_mode[1] -#define TMPIN3 ec.tmpin_mode[2] +#define TMPIN1 ec.tmpin[0] +#define TMPIN2 ec.tmpin[1] +#define TMPIN3 ec.tmpin[2] + #define FAN1 ec.fan[0] #define FAN2 ec.fan[1] #define FAN3 ec.fan[2] -- cgit v1.2.3