From 708743379ae6798a2c5c2087bb860d2d4b54b6b6 Mon Sep 17 00:00:00 2001 From: Jonathan McDowell Date: Wed, 14 Sep 2005 16:18:30 +0000 Subject: Clean up vt8235_early_smbus a bit. git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2038 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1 --- src/southbridge/via/vt8235/vt8235_early_smbus.c | 42 +++++++------------------ 1 file changed, 12 insertions(+), 30 deletions(-) (limited to 'src/southbridge') diff --git a/src/southbridge/via/vt8235/vt8235_early_smbus.c b/src/southbridge/via/vt8235/vt8235_early_smbus.c index 26beea933b..8030f2f3df 100644 --- a/src/southbridge/via/vt8235/vt8235_early_smbus.c +++ b/src/southbridge/via/vt8235/vt8235_early_smbus.c @@ -30,31 +30,24 @@ static void enable_smbus(void) device_t dev; unsigned char c; int i; + /* Power management controller */ - dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235), 0); + dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_8235), 0); if (dev == PCI_DEV_INVALID) { die("SMBUS controller not found\r\n"); } - pci_write_config8(dev, 0xd2, (0x4 << 1 )); // set IO base address to SMBUS_IO_BASE - pci_write_config16(dev, 0xd0, SMBUS_IO_BASE); + pci_write_config16(dev, 0xd0, SMBUS_IO_BASE | 1); // Enable SMBus - pci_write_config8(dev, 0xd2, (0x4 << 1)|1); + pci_write_config8(dev, 0xd2, (0x4 << 1) | 1); - // Enable RTC - pci_write_config8(dev,0x51,0x04); - /* make it work for I/O ... */ pci_write_config16(dev, 4, 1); - - - /* tell the world we're alive - make power led flash during bios execution */ - pci_write_config8(dev,0x94,0xb2); - /* FIX for half baud rate problem */ /* let clocks and the like settle */ @@ -62,28 +55,17 @@ static void enable_smbus(void) for(i = 0 ; i < 5000 ; i++) outb(0x80,0x80); - /* southbridge doesn't seem to like to do much untill after this delay, so set up - * the flashing power LED again */ - pci_write_config8(dev,0x94,0xb2); - -/* The VT1211 serial port needs 48 mhz clock, on power up it is getting - only 24 mhz, there is some mysterious device on the smbus that can - fix this...this code below does it. */ + /* + * The VT1211 serial port needs 48 mhz clock, on power up it is getting + * only 24 mhz, there is some mysterious device on the smbus that can + * fix this...this code below does it. + * */ outb(0xff, SMBUS_IO_BASE+SMBHSTSTAT); - outb(0xff, SMBUS_IO_BASE+SMBHSTSTAT); - outb(0xff, SMBUS_IO_BASE+SMBHSTSTAT); - outb(0xff, SMBUS_IO_BASE+SMBHSTSTAT); - for( ;;) { - c = inb(SMBUS_IO_BASE+SMBHSTSTAT); - if ((c & 1) == 0) - break; - } outb(0x7f, SMBUS_IO_BASE+SMBHSTDAT0); outb(0x83, SMBUS_IO_BASE+SMBHSTCMD); - outb(CLOCK_SLAVE_ADDRESS<<1 , SMBUS_IO_BASE+SMBXMITADD); - outb(8 | I2C_TRANS_CMD, SMBUS_IO_BASE+SMBHSTCTL); + outb(CLOCK_SLAVE_ADDRESS<<1 , SMBUS_IO_BASE+SMBXMITADD); + outb(8 | I2C_TRANS_CMD, SMBUS_IO_BASE+SMBHSTCTL); - for (;;) { c = inb(SMBUS_IO_BASE+SMBHSTSTAT); if ((c & 1) == 0) -- cgit v1.2.3