From ea32c52a0eb9eb9f8cb9ef886e2120d1d5f35753 Mon Sep 17 00:00:00 2001 From: Felix Held Date: Sat, 13 Feb 2021 01:42:44 +0100 Subject: soc/amd/cezanne: add partial data fabric setup I'm not 100% sure yet if this code will be common for all AMD SoCs, so I'll add a copy for Cezanne for now. This part of the code should probably be reworked after the initial bringup of Cezanne anyway. DF MMIO register configuration at the beginning of data_fabric_set_mmio_np: === Data Fabric MMIO configuration registers === Addresses are shifted to the right by 16 bits. idx control base limit 0 a3 fc00 febf 1 a3 1000000 fffcffff 2 a3 d000 f7ff 3 a0 0 0 4 a3 fed0 fed0 5 a0 0 0 6 a0 0 0 7 a0 0 0 DF MMIO register configuration at the end of data_fabric_set_mmio_np: === Data Fabric MMIO configuration registers === Addresses are shifted to the right by 16 bits. idx control base limit 0 a3 fc00 febf 1 a3 1000000 fffcffff 2 a3 d000 f7ff 3 10a3 fed0 fedf 4 a0 0 0 5 a0 0 0 6 a0 0 0 7 a0 0 0 Signed-off-by: Felix Held Change-Id: Ia243a0cad311eb210d14d6242c52f599db22515c Reviewed-on: https://review.coreboot.org/c/coreboot/+/50624 Reviewed-by: Marshall Dawson Tested-by: build bot (Jenkins) --- src/soc/amd/cezanne/Kconfig | 1 + src/soc/amd/cezanne/Makefile.inc | 1 + src/soc/amd/cezanne/chip.c | 3 + src/soc/amd/cezanne/data_fabric.c | 95 +++++++++++++++++++++++++++ src/soc/amd/cezanne/include/soc/data_fabric.h | 14 ++++ 5 files changed, 114 insertions(+) create mode 100644 src/soc/amd/cezanne/data_fabric.c create mode 100644 src/soc/amd/cezanne/include/soc/data_fabric.h (limited to 'src/soc') diff --git a/src/soc/amd/cezanne/Kconfig b/src/soc/amd/cezanne/Kconfig index 9e5209f50e..9dafe2cdb3 100644 --- a/src/soc/amd/cezanne/Kconfig +++ b/src/soc/amd/cezanne/Kconfig @@ -29,6 +29,7 @@ config SOC_SPECIFIC_OPTIONS select SOC_AMD_COMMON_BLOCK_ACPIMMIO select SOC_AMD_COMMON_BLOCK_AOAC select SOC_AMD_COMMON_BLOCK_BANKED_GPIOS + select SOC_AMD_COMMON_BLOCK_DATA_FABRIC select SOC_AMD_COMMON_BLOCK_LPC select SOC_AMD_COMMON_BLOCK_NONCAR select SOC_AMD_COMMON_BLOCK_PCI diff --git a/src/soc/amd/cezanne/Makefile.inc b/src/soc/amd/cezanne/Makefile.inc index d395089242..697d412464 100644 --- a/src/soc/amd/cezanne/Makefile.inc +++ b/src/soc/amd/cezanne/Makefile.inc @@ -27,6 +27,7 @@ romstage-y += uart.c ramstage-y += acpi.c ramstage-y += chip.c ramstage-y += cpu.c +ramstage-y += data_fabric.c ramstage-y += fch.c ramstage-y += fsp_params.c ramstage-y += gpio.c diff --git a/src/soc/amd/cezanne/chip.c b/src/soc/amd/cezanne/chip.c index ffd56de66d..78a4e33d76 100644 --- a/src/soc/amd/cezanne/chip.c +++ b/src/soc/amd/cezanne/chip.c @@ -2,6 +2,7 @@ #include #include +#include #include #include #include "chip.h" @@ -53,6 +54,8 @@ static void soc_init(void *chip_info) { fsp_silicon_init(); + data_fabric_set_mmio_np(); + fch_init(chip_info); } diff --git a/src/soc/amd/cezanne/data_fabric.c b/src/soc/amd/cezanne/data_fabric.c new file mode 100644 index 0000000000..b4bf61818b --- /dev/null +++ b/src/soc/amd/cezanne/data_fabric.c @@ -0,0 +1,95 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include +#include +#include +#include +#include +#include + +void data_fabric_set_mmio_np(void) +{ + /* + * Mark region from HPET-LAPIC or 0xfed00000-0xfee00000-1 as NP. + * + * AGESA has already programmed the NB MMIO routing, however nothing + * is yet marked as non-posted. + * + * If there exists an overlapping routing base/limit pair, trim its + * base or limit to avoid the new NP region. If any pair exists + * completely within HPET-LAPIC range, remove it. If any pair surrounds + * HPET-LAPIC, it must be split into two regions. + * + * TODO(b/156296146): Remove the settings from AGESA and allow coreboot + * to own everything. If not practical, consider erasing all settings + * and have coreboot reprogram them. At that time, make the source + * below more flexible. + * * Note that the code relies on the granularity of the HPET and + * LAPIC addresses being sufficiently large that the shifted limits + * +/-1 are always equivalent to the non-shifted values +/-1. + */ + + unsigned int i; + int reg; + uint32_t base, limit, ctrl; + const uint32_t np_bot = HPET_BASE_ADDRESS >> D18F0_MMIO_SHIFT; + const uint32_t np_top = (LOCAL_APIC_ADDR - 1) >> D18F0_MMIO_SHIFT; + + data_fabric_print_mmio_conf(); + + for (i = 0; i < NUM_NB_MMIO_REGS; i++) { + /* Adjust all registers that overlap */ + ctrl = data_fabric_broadcast_read32(0, NB_MMIO_CONTROL(i)); + if (!(ctrl & (MMIO_WE | MMIO_RE))) + continue; /* not enabled */ + + base = data_fabric_broadcast_read32(0, NB_MMIO_BASE(i)); + limit = data_fabric_broadcast_read32(0, NB_MMIO_LIMIT(i)); + + if (base > np_top || limit < np_bot) + continue; /* no overlap at all */ + + if (base >= np_bot && limit <= np_top) { + data_fabric_disable_mmio_reg(i); /* 100% within, so remove */ + continue; + } + + if (base < np_bot && limit > np_top) { + /* Split the configured region */ + data_fabric_broadcast_write32(0, NB_MMIO_LIMIT(i), np_bot - 1); + reg = data_fabric_find_unused_mmio_reg(); + if (reg < 0) { + /* Although a pair could be freed later, this condition is + * very unusual and deserves analysis. Flag an error and + * leave the topmost part unconfigured. */ + printk(BIOS_ERR, + "Error: Not enough NB MMIO routing registers\n"); + continue; + } + data_fabric_broadcast_write32(0, NB_MMIO_BASE(reg), np_top + 1); + data_fabric_broadcast_write32(0, NB_MMIO_LIMIT(reg), limit); + data_fabric_broadcast_write32(0, NB_MMIO_CONTROL(reg), ctrl); + continue; + } + + /* If still here, adjust only the base or limit */ + if (base <= np_bot) + data_fabric_broadcast_write32(0, NB_MMIO_LIMIT(i), np_bot - 1); + else + data_fabric_broadcast_write32(0, NB_MMIO_BASE(i), np_top + 1); + } + + reg = data_fabric_find_unused_mmio_reg(); + if (reg < 0) { + printk(BIOS_ERR, "Error: cannot configure region as NP\n"); + return; + } + + data_fabric_broadcast_write32(0, NB_MMIO_BASE(reg), np_bot); + data_fabric_broadcast_write32(0, NB_MMIO_LIMIT(reg), np_top); + data_fabric_broadcast_write32(0, NB_MMIO_CONTROL(reg), + (IOMS0_FABRIC_ID << MMIO_DST_FABRIC_ID_SHIFT) | MMIO_NP | MMIO_WE + | MMIO_RE); + + data_fabric_print_mmio_conf(); +} diff --git a/src/soc/amd/cezanne/include/soc/data_fabric.h b/src/soc/amd/cezanne/include/soc/data_fabric.h new file mode 100644 index 0000000000..5dcbdd07ce --- /dev/null +++ b/src/soc/amd/cezanne/include/soc/data_fabric.h @@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#ifndef AMD_CEZANNE_DATA_FABRIC_H +#define AMD_CEZANNE_DATA_FABRIC_H + +#include + +#define IOMS0_FABRIC_ID 10 + +#define NUM_NB_MMIO_REGS 8 + +void data_fabric_set_mmio_np(void); + +#endif /* AMD_CEZANNE_DATA_FABRIC_H */ -- cgit v1.2.3