From 52353d09fc981c48b58ebf8bf44f18ad12e119d2 Mon Sep 17 00:00:00 2001 From: satya priya Date: Thu, 19 Sep 2019 16:45:18 +0530 Subject: sc7180: Add I2C driver Add I2C functionality in coreboot. Change-Id: I61221ffff8afe5c7ede5abb9e194e242ab0274d8 Signed-off-by: Roja Rani Yarubandi Reviewed-on: https://review.coreboot.org/c/coreboot/+/36830 Reviewed-by: Julius Werner Tested-by: build bot (Jenkins) --- src/soc/qualcomm/sc7180/Makefile.inc | 4 + src/soc/qualcomm/sc7180/include/soc/qupv3_i2c.h | 23 ++++ src/soc/qualcomm/sc7180/qupv3_i2c.c | 165 ++++++++++++++++++++++++ 3 files changed, 192 insertions(+) create mode 100644 src/soc/qualcomm/sc7180/include/soc/qupv3_i2c.h create mode 100644 src/soc/qualcomm/sc7180/qupv3_i2c.c (limited to 'src/soc') diff --git a/src/soc/qualcomm/sc7180/Makefile.inc b/src/soc/qualcomm/sc7180/Makefile.inc index 4a931f4b9c..4961d244d0 100644 --- a/src/soc/qualcomm/sc7180/Makefile.inc +++ b/src/soc/qualcomm/sc7180/Makefile.inc @@ -8,6 +8,7 @@ bootblock-y += timer.c bootblock-y += spi.c bootblock-y += qupv3_spi.c bootblock-y += gpio.c +bootblock-y += qupv3_i2c.c bootblock-$(CONFIG_DRIVERS_UART) += uart_bitbang.c bootblock-y += clock.c bootblock-$(CONFIG_SC7180_QSPI) += qspi.c @@ -19,6 +20,7 @@ verstage-y += timer.c verstage-y += spi.c verstage-y += qupv3_spi.c verstage-y += gpio.c +verstage-y += qupv3_i2c.c verstage-y += clock.c verstage-$(CONFIG_SC7180_QSPI) += qspi.c verstage-y += qcom_qup_se.c @@ -36,6 +38,7 @@ romstage-y += usb.c romstage-y += spi.c romstage-y += qupv3_spi.c romstage-y += gpio.c +romstage-y += qupv3_i2c.c romstage-y += clock.c romstage-$(CONFIG_SC7180_QSPI) += qspi.c romstage-y += qcom_qup_se.c @@ -48,6 +51,7 @@ ramstage-y += timer.c ramstage-y += spi.c ramstage-y += qupv3_spi.c ramstage-y += gpio.c +ramstage-y += qupv3_i2c.c ramstage-y += clock.c ramstage-$(CONFIG_SC7180_QSPI) += qspi.c ramstage-y += aop_load_reset.c diff --git a/src/soc/qualcomm/sc7180/include/soc/qupv3_i2c.h b/src/soc/qualcomm/sc7180/include/soc/qupv3_i2c.h new file mode 100644 index 0000000000..e69f461ff9 --- /dev/null +++ b/src/soc/qualcomm/sc7180/include/soc/qupv3_i2c.h @@ -0,0 +1,23 @@ +/* + * This file is part of the depthcharge project. + * + * Copyright (C) 2018-2019, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __I2C_QCOM_HEADER___ +#define __I2C_QCOM_HEADER___ + +#include + +void i2c_init(unsigned int bus, enum i2c_speed speed); + +#endif /* __I2C_QCOM_HEADER */ diff --git a/src/soc/qualcomm/sc7180/qupv3_i2c.c b/src/soc/qualcomm/sc7180/qupv3_i2c.c new file mode 100644 index 0000000000..b8938e2315 --- /dev/null +++ b/src/soc/qualcomm/sc7180/qupv3_i2c.c @@ -0,0 +1,165 @@ +/* + * This file is part of the depthcharge project. + * + * Copyright (C) 2018-2020, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +static void i2c_clk_configure(unsigned int bus, enum i2c_speed speed) +{ + int clk_div = 0, t_high = 0, t_low = 0, t_cycle = 0; + struct qup_regs *regs = qup[bus].regs; + + switch (speed) { + case I2C_SPEED_STANDARD: + clk_div = 7; + t_high = 10; + t_low = 11; + t_cycle = 26; + break; + case I2C_SPEED_FAST: + clk_div = 2; + t_high = 5; + t_low = 12; + t_cycle = 24; + break; + case I2C_SPEED_FAST_PLUS: + clk_div = 1; + t_high = 3; + t_low = 9; + t_cycle = 18; + break; + default: + die("Unsupported I2C speed"); + } + + write32(®s->geni_ser_m_clk_cfg, (clk_div << 4) | 1); + /* Serial clock frequency is 19.2 MHz */ + write32(®s->i2c_scl_counters, ((t_high << 20) | (t_low << 10) + | t_cycle)); +} + +void i2c_init(unsigned int bus, enum i2c_speed speed) +{ + uint32_t proto; + struct qup_regs *regs = qup[bus].regs; + + qupv3_se_fw_load_and_init(bus, SE_PROTOCOL_I2C, MIXED); + clock_enable_qup(bus); + i2c_clk_configure(bus, speed); + + proto = ((read32(®s->geni_fw_revision_ro) & + GENI_FW_REVISION_RO_PROTOCOL_MASK) >> + GENI_FW_REVISION_RO_PROTOCOL_SHIFT); + + assert(proto == 3); + + /* Serial engine IO initialization */ + write32(®s->geni_cgc_ctrl, DEFAULT_CGC_EN); + write32(®s->dma_general_cfg, + (AHB_SEC_SLV_CLK_CGC_ON | DMA_AHB_SLV_CFG_ON + | DMA_TX_CLK_CGC_ON | DMA_RX_CLK_CGC_ON)); + write32(®s->geni_output_ctrl, + DEFAULT_IO_OUTPUT_CTRL_MSK); + write32(®s->geni_force_default_reg, FORCE_DEFAULT); + + /* Serial engine IO set mode */ + write32(®s->se_irq_en, (GENI_M_IRQ_EN | + GENI_S_IRQ_EN | DMA_TX_IRQ_EN | DMA_RX_IRQ_EN)); + write32(®s->se_gsi_event_en, 0); + + /* Set RX and RFR watermark */ + write32(®s->geni_rx_watermark_reg, 0); + write32(®s->geni_rx_rfr_watermark_reg, FIFO_DEPTH - 2); + + /* FIFO PACKING CONFIGURATION */ + write32(®s->geni_tx_packing_cfg0, PACK_VECTOR0 + | (PACK_VECTOR1 << 10)); + write32(®s->geni_tx_packing_cfg1, PACK_VECTOR2 + | (PACK_VECTOR3 << 10)); + write32(®s->geni_rx_packing_cfg0, PACK_VECTOR0 + | (PACK_VECTOR1 << 10)); + write32(®s->geni_rx_packing_cfg1, PACK_VECTOR2 + | (PACK_VECTOR3 << 10)); + write32(®s->geni_byte_granularity, (log2(BITS_PER_WORD) - 3)); + + /* GPIO Configuration */ + gpio_configure(qup[bus].pin[0], qup[bus].func[0], GPIO_PULL_UP, + GPIO_2MA, GPIO_OUTPUT_ENABLE); + gpio_configure(qup[bus].pin[1], qup[bus].func[1], GPIO_PULL_UP, + GPIO_2MA, GPIO_OUTPUT_ENABLE); + + /* Select and setup FIFO mode */ + write32(®s->geni_m_irq_clear, 0xFFFFFFFF); + write32(®s->geni_s_irq_clear, 0xFFFFFFFF); + write32(®s->dma_tx_irq_clr, 0xFFFFFFFF); + write32(®s->dma_rx_irq_clr, 0xFFFFFFFF); + write32(®s->geni_m_irq_enable, (M_COMMON_GENI_M_IRQ_EN | + M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN | + M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN)); + write32(®s->geni_s_irq_enable, (S_COMMON_GENI_S_IRQ_EN + | S_CMD_DONE_EN)); + clrbits32(®s->geni_dma_mode_en, GENI_DMA_MODE_EN); +} + +static int i2c_do_xfer(unsigned int bus, struct i2c_msg segment, + unsigned int prams) +{ + unsigned int cmd = (segment.flags & I2C_M_RD) ? 2 : 1; + unsigned int master_cmd_reg_val = (cmd << M_OPCODE_SHFT); + struct qup_regs *regs = qup[bus].regs; + void *dout = NULL, *din = NULL; + + if (!(segment.flags & I2C_M_RD)) { + write32(®s->i2c_tx_trans_len, segment.len); + write32(®s->geni_tx_watermark_reg, TX_WATERMARK); + dout = segment.buf; + } else { + write32(®s->i2c_rx_trans_len, segment.len); + din = segment.buf; + } + + master_cmd_reg_val |= (prams & M_PARAMS_MSK); + write32(®s->geni_m_cmd0, master_cmd_reg_val); + + return qup_handle_transfer(bus, dout, din, segment.len); +} + +int platform_i2c_transfer(unsigned int bus, struct i2c_msg *segments, + int seg_count) +{ + struct i2c_msg *seg = segments; + int ret = 0; + + while (!ret && seg_count--) { + /* Stretch means end with repeated start, not stop */ + u32 stretch = (seg_count ? 1 : 0); + u32 m_param = 0; + + m_param |= (stretch << 2); + m_param |= ((seg->slave & 0x7F) << 9); + ret = i2c_do_xfer(bus, *seg, m_param); + seg++; + } + return ret; +} -- cgit v1.2.3