From 969531b6d8c015c329f96840a1337d6b7e9c5595 Mon Sep 17 00:00:00 2001 From: Mario Scheithauer Date: Tue, 8 Nov 2022 14:03:00 +0100 Subject: mb/siemens/mc_ehl2: Enable Marvell PHY 88E1512 driver This mainboard has three Marvel PHYs connected to the internal SOC GbE controllers. The default LED status after HW reset of this PHYs shows a different mode than what is needed. LED[2] is not connected on this mainboard. This patch sets the following LED status: LED[0] - 7 = On - 1000 Mbps Link, Off - Else LED[1] - 1 = On - Link, Blink - Activity, Off - No Link LED[2] - not connected TEST=Try different register values to verify LED feature. Change-Id: I51d817bc720bf787279777f503efdc17dbb1274d Signed-off-by: Mario Scheithauer Reviewed-on: https://review.coreboot.org/c/coreboot/+/69387 Reviewed-by: Werner Zeh Reviewed-by: Arthur Heymans Tested-by: build bot (Jenkins) --- .../siemens/mc_ehl/variants/mc_ehl2/Kconfig | 1 + .../siemens/mc_ehl/variants/mc_ehl2/devicetree.cb | 42 ++++++++++++++++++++-- 2 files changed, 40 insertions(+), 3 deletions(-) (limited to 'src/mainboard/siemens/mc_ehl') diff --git a/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/Kconfig b/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/Kconfig index 00875fbb25..9e3e9dccb3 100644 --- a/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/Kconfig +++ b/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/Kconfig @@ -6,6 +6,7 @@ config BOARD_SPECIFIC_OPTIONS select DRIVER_INTEL_I210 select SOC_INTEL_COMMON_BLOCK_LPC_COMB_ENABLE select EHL_TSN_DRIVER + select DRIVERS_ETH_PHY_M88E1512 config FMDFILE default "src/mainboard/\$(CONFIG_MAINBOARD_DIR)/mc_ehl.fmd" diff --git a/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/devicetree.cb b/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/devicetree.cb index 4dd062cb55..b8ea1b6213 100644 --- a/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/devicetree.cb +++ b/src/mainboard/siemens/mc_ehl/variants/mc_ehl2/devicetree.cb @@ -181,12 +181,48 @@ chip soc/intel/elkhartlake device pci 1c.6 on end # RP7 (pcie3 multi VC) device pci 1d.0 off end # Intel PSE IPC (local host to PSE) - device pci 1d.1 on end # Intel PSE Time-Sensitive Networking GbE 0 - device pci 1d.2 on end # Intel PSE Time-Sensitive Networking GbE 1 + device pci 1d.1 on # Intel PSE Time-Sensitive Networking GbE 0 + # Enable external Marvell PHY 88E1512 + chip drivers/net/phy/m88e1512 + register "configure_leds" = "true" + # LED[0]: On - 1000 Mbps Link, Off - Else + register "led_0_ctrl" = "7" + # LED[1]: On - Link, Blink - Activity, Off - No Link + register "led_1_ctrl" = "1" + device mdio 0 on # PHY address + ops m88e1512_ops + end + end + end + device pci 1d.2 on # Intel PSE Time-Sensitive Networking GbE 1 + # Enable external Marvell PHY 88E1512 + chip drivers/net/phy/m88e1512 + register "configure_leds" = "true" + # LED[0]: On - 1000 Mbps Link, Off - Else + register "led_0_ctrl" = "7" + # LED[1]: On - Link, Blink - Activity, Off - No Link + register "led_1_ctrl" = "1" + device mdio 1 on # PHY address + ops m88e1512_ops + end + end + end device pci 1e.0 on end # UART0 device pci 1e.1 on end # UART1 - device pci 1e.4 on end # PCH Time-Sensitive Networking GbE + device pci 1e.4 on # PCH Time-Sensitive Networking GbE + # Enable external Marvell PHY 88E1512 + chip drivers/net/phy/m88e1512 + register "configure_leds" = "true" + # LED[0]: On - 1000 Mbps Link, Off - Else + register "led_0_ctrl" = "7" + # LED[1]: On - Link, Blink - Activity, Off - No Link + register "led_1_ctrl" = "1" + device mdio 1 on # PHY address + ops m88e1512_ops + end + end + end device pci 1f.0 on # eSPI Interface chip drivers/pc80/tpm -- cgit v1.2.3