From 69254494a0b03d870ab925f0a474c6077a358229 Mon Sep 17 00:00:00 2001 From: Tim Wawrzynczak Date: Wed, 7 Aug 2019 11:08:07 -0600 Subject: mb/google/hatch: Kohaku: Add touchscreen controller to device tree The touchscreen controller was never added to the device tree, and the next board rev will have this IC connected. Set it up in the device tree with conservative power resource timings from the datasheet. BUG=b:138869702 BRANCH=none TEST=compiles; current board rev does not have touch IC Change-Id: I759fb32f31c8eee0e6bd664c6a82308354ef5d08 Signed-off-by: Tim Wawrzynczak Reviewed-on: https://review.coreboot.org/c/coreboot/+/34763 Tested-by: build bot (Jenkins) Reviewed-by: Paul Fagerburg Reviewed-by: Furquan Shaikh --- src/mainboard/google/hatch/variants/kohaku/gpio.c | 4 ++++ .../google/hatch/variants/kohaku/overridetree.cb | 15 +++++++++++++++ 2 files changed, 19 insertions(+) (limited to 'src/mainboard/google/hatch/variants') diff --git a/src/mainboard/google/hatch/variants/kohaku/gpio.c b/src/mainboard/google/hatch/variants/kohaku/gpio.c index d22de04648..bc9df38ab5 100644 --- a/src/mainboard/google/hatch/variants/kohaku/gpio.c +++ b/src/mainboard/google/hatch/variants/kohaku/gpio.c @@ -41,10 +41,14 @@ static const struct pad_config gpio_table[] = { PAD_NC(GPP_C1, NONE), /* C7 : PEN_IRQ_OD_L */ PAD_CFG_GPI_APIC(GPP_C7, NONE, PLTRST, LEVEL, INVERT), + /* C12 : EN_PP3300_TSP_DX */ + PAD_CFG_GPO(GPP_C12, 0, DEEP), /* C15 : EN_PP3300_DIG_DX */ PAD_CFG_GPO(GPP_C15, 0, DEEP), /* C23 : UART2_CTS# ==> NC */ PAD_NC(GPP_C23, NONE), + /* D16 : TOUCHSCREEN_INT_L */ + PAD_CFG_GPI_APIC(GPP_D16, NONE, PLTRST, LEVEL, INVERT), /* E23 : GPP_E23 ==> NC */ PAD_NC(GPP_E23, NONE), /* F1 : GPP_F1 ==> NC */ diff --git a/src/mainboard/google/hatch/variants/kohaku/overridetree.cb b/src/mainboard/google/hatch/variants/kohaku/overridetree.cb index 8a1de845a7..57429ad0b8 100644 --- a/src/mainboard/google/hatch/variants/kohaku/overridetree.cb +++ b/src/mainboard/google/hatch/variants/kohaku/overridetree.cb @@ -81,6 +81,21 @@ chip soc/intel/cannonlake end end # I2C 0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ATML0001"" + register "desc" = ""Atmel Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" + register "reset_delay_ms" = "91" # 90.5 ms + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C12)" + register "enable_delay_ms" = "1" # 90 ns + register "has_power_resource" = "1" + register "disable_gpio_export_in_crs" = "1" + device i2c 4b on end + end + end # I2C #1 + device pci 15.2 on chip drivers/i2c/hid register "generic.hid" = ""WCOM50C1"" -- cgit v1.2.3