From 7b6a0a84bea27bdb332b082e6d602f0596a2a8c8 Mon Sep 17 00:00:00 2001 From: "Ronald G. Minnich" Date: Wed, 7 Oct 2009 18:03:41 +0000 Subject: Get rid of early_serial, it is now a generic function in early_init. Add some more enables to the s1850. Signed-off-by: Ronald G. Minnich Acked-by: Stefan Reinauer git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4736 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1 --- src/mainboard/dell/s1850/auto.c | 61 +++++++++++++++++++++++++++++++++++------ 1 file changed, 53 insertions(+), 8 deletions(-) (limited to 'src/mainboard/dell') diff --git a/src/mainboard/dell/s1850/auto.c b/src/mainboard/dell/s1850/auto.c index 51bd74bb12..f1d2c65592 100644 --- a/src/mainboard/dell/s1850/auto.c +++ b/src/mainboard/dell/s1850/auto.c @@ -13,7 +13,7 @@ #include "lib/ramtest.c" #include "southbridge/intel/i82801er/i82801er_early_smbus.c" #include "northbridge/intel/e7520/raminit.h" -#include "superio/nsc/pc8374/pc8374_early_serial.c" +#include "superio/nsc/pc8374/pc8374_early_init.c" #include "cpu/x86/lapic/boot_cpu.c" #include "cpu/x86/mtrr/earlymtrr.c" #include "debug.c" @@ -65,6 +65,25 @@ static inline void activate_spd_rom(const struct mem_controller *ctrl) } static inline int spd_read_byte(unsigned device, unsigned address) { + /* fake it out for this board */ + switch(device) { + case 0x52: + case 0x53: + print_debug("FAKE"); + device = 0x50; + break; + case 0x50: + case 0x51: + case 0x54: + case 0x55: + case 0x56: + case 0x57: + print_debug("57"); + device = 0x57; + break; + default: + die("BAD DEV IN spd_read_byte"); + } return smbus_read_byte(device, address); } @@ -191,11 +210,22 @@ static void main(unsigned long bist) .f1 = PCI_DEV(0, 0x00, 1), .f2 = PCI_DEV(0, 0x00, 2), .f3 = PCI_DEV(0, 0x00, 3), - .channel0 = {(0xa<<3)|3, (0xa<<3)|2, (0xa<<3)|1, (0xa<<3)|0, }, - .channel1 = {(0xa<<3)|7, (0xa<<3)|6, (0xa<<3)|5, (0xa<<3)|4, }, + .channel0 = {(0xa<<3)|0, (0xa<<3)|1, (0xa<<3)|2, (0xa<<3)|3, }, + .channel1 = {(0xa<<3)|4, (0xa<<3)|5, (0xa<<3)|6, (0xa<<3)|7, }, } }; + /* superio setup */ + /* observed from serialice */ + static const u8 earlyinit[] = { + 0x21, 0x11, 0x11, + 0x22, 1, 1, + 0x23, 05, 05, + 0x24, 0x81, 0x81, + 0x26, 0, 0, + 0, + }; + /* using SerialICE, we've seen this basic reset sequence on the dell. * we don't understand it as it uses undocumented registers, but * we're going to clone it. @@ -261,10 +291,10 @@ static void main(unsigned long bist) pci_write_config8(PCI_DEV(0, 0, 0), 0xf4, b); /* ?? */ - l = pci_read_config32(PCI_DEV(0, 0, 8), 0xc0); + l = pci_read_config32(PCI_DEV(0, 8, 0), 0xc0); do_reset = l & 0x8000000; l |= 0x8000000; - pci_write_config32(PCI_DEV(0, 0, 2), 0xc0, l); + pci_write_config32(PCI_DEV(0, 8, 0), 0xc0, l); if (! do_reset) { outb(2, 0xcf9); @@ -279,11 +309,26 @@ static void main(unsigned long bist) } /* Setup the console */ mainboard_set_ich5(); - bmc_foad(); - pc8374_enable_serial(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE); + //bmc_foad(); + pc8374_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE); uart_init(); console_init(); + /* stuff we seem to need */ + pc8374_enable_dev(PC8374_KBCK, 0); + + /* GPIOs */ + pc8374_enable_dev(PC8374_GPIO, 0xc20); + + /* keep this in mind. + SerialICE-hlp: outb 002e <= 23 + SerialICE-hlp: inb 002f => 05 + SerialICE-hlp: outb 002f <= 05 + SerialICE-hlp: outb 002e <= 24 + SerialICE-hlp: inb 002f => c1 + SerialICE-hlp: outb 002f <= c1 + */ + /* Halt if there was a built in self test failure */ // report_bist_failure(bist); @@ -306,7 +351,7 @@ static void main(unsigned long bist) #if 1 enable_smbus(); #endif -#if 1 +#if 0 // dump_spd_registers(&cpu[0]); int i; for(i = 0; i < 1; i++) { -- cgit v1.2.3