From 472d68b066ebf73f9718029223fa181123ef72bb Mon Sep 17 00:00:00 2001 From: Timothy Pearson Date: Mon, 22 May 2017 13:12:16 -0500 Subject: mb/asus/kgpe-d16: Set ASpeed GPIO SPD mux lines during boot When the BMC firmware module is installed on the KGPE-D16, the RAM SPD multiplexer lines are disconnected by hardware from the SP5100 GPIOs and attached to BMC GPIO lines instead. Set the BMC GPIOs to match the state of the SP5100 GPIOs during RAM setup. Change-Id: Ia251334ae44668c2260d8d2e816f85f1f62faac5 Signed-off-by: Timothy Pearson Signed-off-by: Arthur Heymans Reviewed-on: https://review.coreboot.org/c/19820 Tested-by: build bot (Jenkins) Reviewed-by: Felix Held --- src/mainboard/asus/kgpe-d16/romstage.c | 70 ++++++++++++++++++++++++++++++++++ 1 file changed, 70 insertions(+) (limited to 'src/mainboard/asus') diff --git a/src/mainboard/asus/kgpe-d16/romstage.c b/src/mainboard/asus/kgpe-d16/romstage.c index bfa40427e4..1b586fd369 100644 --- a/src/mainboard/asus/kgpe-d16/romstage.c +++ b/src/mainboard/asus/kgpe-d16/romstage.c @@ -87,6 +87,76 @@ static void switch_spd_mux(uint8_t channel) byte &= ~0xc0; /* Enable SPD mux GPIO output drivers */ byte |= (channel << 2) & 0xc; /* Set SPD mux GPIOs */ pci_write_config8(PCI_DEV(0, 0x14, 0), 0x54, byte); + + /* Temporary AST PCI mapping */ + const uint32_t memory_base = 0xfc000000; + const uint32_t memory_limit = 0xfc800000; + +#define TEMP_PCI_BUS 0x2 + /* Save S100 PCI bridge settings */ + uint16_t prev_sec_cfg = pci_read_config16(PCI_DEV(0, 0x14, 4), + PCI_COMMAND); + uint8_t prev_sec_bus = pci_read_config8(PCI_DEV(0, 0x14, 4), + PCI_SECONDARY_BUS); + uint8_t prev_sec_sub_bus = pci_read_config8(PCI_DEV(0, 0x14, 4), + PCI_SUBORDINATE_BUS); + uint16_t prev_sec_mem_base = pci_read_config16(PCI_DEV(0, 0x14, 4), + PCI_MEMORY_BASE); + uint16_t prev_sec_mem_limit = pci_read_config16(PCI_DEV(0, 0x14, 4), + PCI_MEMORY_LIMIT); + /* Temporarily enable the SP5100 PCI bridge */ + pci_write_config8(PCI_DEV(0, 0x14, 4), PCI_SECONDARY_BUS, TEMP_PCI_BUS); + pci_write_config8(PCI_DEV(0, 0x14, 4), PCI_SUBORDINATE_BUS, 0xff); + pci_write_config16(PCI_DEV(0, 0x14, 4), PCI_MEMORY_BASE, + (memory_base >> 20)); + pci_write_config16(PCI_DEV(0, 0x14, 4), PCI_MEMORY_LIMIT, + (memory_limit >> 20)); + pci_write_config16(PCI_DEV(0, 0x14, 4), PCI_COMMAND, + PCI_COMMAND_MEMORY); + + /* Temporarily enable AST BAR1 */ + uint16_t prev_ast_cmd = pci_read_config16(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), + PCI_COMMAND); + uint16_t prev_ast_sts = pci_read_config16(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), + PCI_STATUS); + uint32_t prev_ast_bar1 = pci_read_config32( + PCI_DEV(TEMP_PCI_BUS, 0x1, 0), PCI_BASE_ADDRESS_1); + pci_write_config32(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), PCI_BASE_ADDRESS_1, + memory_base); + pci_write_config16(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), PCI_COMMAND, + PCI_COMMAND_MEMORY); + pci_write_config16(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), PCI_STATUS, + PCI_STATUS_CAP_LIST | PCI_STATUS_DEVSEL_MEDIUM); + + /* Use the P2A bridge to set ASpeed SPD mux GPIOs to the same values as the SP5100 */ + void* ast_bar1 = (void*)memory_base; + /* Enable access to GPIO controller */ + write32(ast_bar1 + 0xf004, 0x1e780000); + write32(ast_bar1 + 0xf000, 0x1); + /* Enable SPD mux GPIO output drivers */ + write32(ast_bar1 + 0x10024, read32(ast_bar1 + 0x10024) | 0x3000); + /* Set SPD mux GPIOs */ + write32(ast_bar1 + 0x10020, (read32(ast_bar1 + 0x10020) & ~0x3000) + | ((channel & 0x3) << 12)); + write32(ast_bar1 + 0xf000, 0x0); + + /* Deconfigure AST BAR1 */ + pci_write_config16(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), PCI_COMMAND, + prev_ast_cmd); + pci_write_config16(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), PCI_STATUS, + prev_ast_sts); + pci_write_config32(PCI_DEV(TEMP_PCI_BUS, 0x1, 0), PCI_BASE_ADDRESS_1, + prev_ast_bar1); + + /* Deconfigure SP5100 PCI bridge */ + pci_write_config16(PCI_DEV(0, 0x14, 4), PCI_COMMAND, prev_sec_cfg); + pci_write_config16(PCI_DEV(0, 0x14, 4), PCI_MEMORY_LIMIT, + prev_sec_mem_limit); + pci_write_config16(PCI_DEV(0, 0x14, 4), PCI_MEMORY_BASE, + prev_sec_mem_base); + pci_write_config8(PCI_DEV(0, 0x14, 4), PCI_SUBORDINATE_BUS, + prev_sec_sub_bus); + pci_write_config8(PCI_DEV(0, 0x14, 4), PCI_SECONDARY_BUS, prev_sec_bus); } static const uint8_t spd_addr_fam15[] = { -- cgit v1.2.3