From 2ce8bfd251cfee8a19c09217ace28a5be2684311 Mon Sep 17 00:00:00 2001 From: Marc Jones Date: Wed, 19 Dec 2007 01:49:44 +0000 Subject: Initial AMD Serengeti_Cheetah_FAM10 platform for Barcelona support. Signed-off-by: Marc Jones Reviewed-by: Jordan Crouse Acked-by: Ronald G. Minnich git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3016 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1 --- .../amd/serengeti_cheetah_fam10/Options.lb | 357 +++++++++++++++++++++ 1 file changed, 357 insertions(+) create mode 100644 src/mainboard/amd/serengeti_cheetah_fam10/Options.lb (limited to 'src/mainboard/amd/serengeti_cheetah_fam10/Options.lb') diff --git a/src/mainboard/amd/serengeti_cheetah_fam10/Options.lb b/src/mainboard/amd/serengeti_cheetah_fam10/Options.lb new file mode 100644 index 0000000000..6c09cc4e5d --- /dev/null +++ b/src/mainboard/amd/serengeti_cheetah_fam10/Options.lb @@ -0,0 +1,357 @@ +# +# This file is part of the LinuxBIOS project. +# +# Copyright (C) 2007 Advanced Micro Devices, Inc. +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; version 2 of the License. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +# + +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses HAVE_ACPI_TABLES +uses ACPI_SSDTX_NUM +uses USE_FALLBACK_IMAGE +uses USE_FAILOVER_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_FAILOVER_BOOT +uses HAVE_HARD_RESET +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses CONFIG_LOGICAL_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses FAILOVER_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_PAYLOAD +uses CONFIG_ROM_PAYLOAD_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD +uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_CONSOLE_SERIAL8250 +uses HAVE_INIT_TIMER +uses CONFIG_GDB_STUB +uses CONFIG_GDB_STUB +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses CONFIG_CHIP_NAME +uses CONFIG_CONSOLE_VGA +uses CONFIG_PCI_ROM_RUN +uses HW_MEM_HOLE_SIZEK +uses HW_MEM_HOLE_SIZE_AUTO_INC + +uses HT_CHAIN_UNITID_BASE +uses HT_CHAIN_END_UNITID_BASE +uses SB_HT_CHAIN_ON_BUS0 +uses SB_HT_CHAIN_UNITID_OFFSET_ONLY + +uses USE_DCACHE_RAM +uses DCACHE_RAM_BASE +uses DCACHE_RAM_SIZE +uses DCACHE_RAM_GLOBAL_VAR_SIZE +uses CONFIG_USE_INIT + +uses SERIAL_CPU_INIT + +uses ENABLE_APIC_EXT_ID +uses APIC_ID_OFFSET +uses LIFT_BSP_APIC_ID + +uses CONFIG_PCI_64BIT_PREF_MEM + +uses CONFIG_LB_MEM_TOPK + +uses PCI_BUS_SEGN_BITS + +uses CONFIG_AP_CODE_IN_CAR + +uses MEM_TRAIN_SEQ + +uses WAIT_BEFORE_CPUS_INIT + +uses CONFIG_AMDMCT + +uses CONFIG_USE_PRINTK_IN_CAR +uses CAR_FAM10 + +### +### Build options +### + +## +## ROM_SIZE is the size of boot ROM that this board will use. +## +default ROM_SIZE=524288 + +## +## +#FALLBACK_SIZE_SIZE is the amount of the ROM the complete fallback image will use +## +#default FALLBACK_SIZE=131072 +#default FALLBACK_SIZE=0x40000 + +#FALLBACK: 512K - 4K +default FALLBACK_SIZE=0x7f000 +#FAILOVER: 4k +default FAILOVER_SIZE=0x01000 + +#more 1M for pgtbl +#if there is RAM on node0, we need to set it to 32M, otherwise can not access CAR on node0, and RAM on node1 at same time. +default CONFIG_LB_MEM_TOPK=16384 + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 +default HAVE_FAILOVER_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=11 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## ACPI tables will be included +default HAVE_ACPI_TABLES=1 +## extra SSDT num +default ACPI_SSDTX_NUM=31 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=1 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_PHYSICAL_CPUS=2 +default CONFIG_MAX_CPUS=4 * CONFIG_MAX_PHYSICAL_CPUS +default CONFIG_LOGICAL_CPUS=1 + +#default SERIAL_CPU_INIT=0 + +default ENABLE_APIC_EXT_ID=1 +default APIC_ID_OFFSET=0x00 +default LIFT_BSP_APIC_ID=1 + +#CHIP_NAME ? +default CONFIG_CHIP_NAME=1 + +#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead. +#2G +#default HW_MEM_HOLE_SIZEK=0x200000 +#1G +default HW_MEM_HOLE_SIZEK=0x100000 +#512M +#default HW_MEM_HOLE_SIZEK=0x80000 + +#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy +#default HW_MEM_HOLE_SIZE_AUTO_INC=1 + +#VGA Console +default CONFIG_CONSOLE_VGA=1 +default CONFIG_PCI_ROM_RUN=1 + +#HT Unit ID offset, default is 1, the typical one +default HT_CHAIN_UNITID_BASE=0xa + +#real SB Unit ID, default is 0x20, mean dont touch it at last +default HT_CHAIN_END_UNITID_BASE=0x6 + +#make the SB HT chain on bus 0, default is not (0) +default SB_HT_CHAIN_ON_BUS0=2 + +#only offset for SB chain?, default is yes(1) +#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 + +#allow capable device use that above 4G +#default CONFIG_PCI_64BIT_PREF_MEM=1 + +#it only be 0, 1, 2, 3, 4 and default is 0 +#default PCI_BUS_SEGN_BITS=3 + +## +## enable CACHE_AS_RAM specifics +## +default USE_DCACHE_RAM=1 +default DCACHE_RAM_BASE=0xc4000 +default DCACHE_RAM_SIZE=0x0c000 +#default DCACHE_RAM_GLOBAL_VAR_SIZE=0x08000 +default DCACHE_RAM_GLOBAL_VAR_SIZE=0x04000 +default CONFIG_USE_INIT=0 + +#default CONFIG_AP_CODE_IN_CAR=1 +default MEM_TRAIN_SEQ=2 +default WAIT_BEFORE_CPUS_INIT=0 + +default CONFIG_AMDMCT = 1 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +default MAINBOARD_PART_NUMBER="Cheetah Fam10" +default MAINBOARD_VENDOR="AMD" +default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022 +default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 768k heap +## +default HEAP_SIZE=0xc0000 + +## +## Only use the option table in a normal image +## +default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE ) + +## +## LinuxBIOS C code runs at this location in RAM +## +default _RAMBASE=0x00200000 + +## +## Load the payload from the ROM +## +default CONFIG_ROM_PAYLOAD = 1 + +### +### Defaults of options that you may want to override in the target config file +### + +## +## The default compiler +## +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## Disable the gdb stub by default +## +default CONFIG_GDB_STUB=0 + +## +## The Serial Console +## + +default CONFIG_USE_PRINTK_IN_CAR=1 + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +## +## Select power on after power fail setting +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" + +### End Options.lb +end -- cgit v1.2.3