From 1c18f8679fd909de01959394264655a1f23892ff Mon Sep 17 00:00:00 2001 From: Sam Lewis Date: Sun, 9 Aug 2020 16:55:39 +1000 Subject: Documentation: Add Beaglebone Black documentation Change-Id: If1a9808d1f20ee61048182d416f25e9a81c631af Signed-off-by: Sam Lewis Reviewed-on: https://review.coreboot.org/c/coreboot/+/44389 Tested-by: build bot (Jenkins) Reviewed-by: Arthur Heymans --- Documentation/mainboard/index.md | 4 + Documentation/mainboard/ti/beaglebone-black.md | 131 +++++++++++++++++++++++++ 2 files changed, 135 insertions(+) create mode 100644 Documentation/mainboard/ti/beaglebone-black.md (limited to 'Documentation') diff --git a/Documentation/mainboard/index.md b/Documentation/mainboard/index.md index 95efe55e50..1f8f6bc26e 100644 --- a/Documentation/mainboard/index.md +++ b/Documentation/mainboard/index.md @@ -176,6 +176,10 @@ The boards in this section are not real mainboards, but emulators. - [Lemur Pro](system76/lemp9.md) +## Texas Instruments + +- [Beaglebone Black](ti/beaglebone-black.md) + ## UP - [Squared](up/squared/index.md) diff --git a/Documentation/mainboard/ti/beaglebone-black.md b/Documentation/mainboard/ti/beaglebone-black.md new file mode 100644 index 0000000000..db37e28099 --- /dev/null +++ b/Documentation/mainboard/ti/beaglebone-black.md @@ -0,0 +1,131 @@ +# Beaglebone Black +This page gives some details about the [BeagleBone Black] coreboot port and +describes how to build and run it. + +The port currently only supports booting coreboot from a micro SD card and has +some other limitations listed below. + +## Supported Boards +The Beaglebone port supports the following boards: + +- Beaglebone Black +- Beaglebone Black Wireless +- Beaglebone Pocket (untested, may need tweaking) +- Beaglebone Blue (untested, may need tweaking) +- Beaglebone Original (untested, may need tweaking) + +## Use Cases +This port was primarily developed as a learning exercise and there is +potentially little reason to use it compared to the defacto bootloader choice of +U-Boot. However, it does have some interesting practical use cases compared to +U-Boot: + +1. Choosing coreboot as a lightweight alternative to U-Boot. In this case, + coreboot is used to do the absolute minimum necessary to boot Linux, forgoing + some U-Boot features and functionality. Complex boot logic can then instead + be moved into Linux where it can be more flexibly and safely executed. This + is essentially the LinuxBoot philosophy. [U-Boot Falcon mode] has similar + goals to this as well. +2. Facilitating experimenting with coreboot on real hardware. The Beaglebone + Black is widely available at a low pricepoint (~$65) making it a great way to + experiment with coreboot on real ARMv7 hardware. It also works well as a + development platform as it has exposed pads for JTAG and, due to the way it + boots, is effectively impossible to brick. +3. The Beaglebone Black is often used as a external flasher and EHCI debug + gadget in the coreboot community, so many members have access to it and can + use it as a reference platform. + +## Quickstart +1. Run `make menuconfig` and select _TI_/_Beaglebone_ in the _Mainboard_ menu. +2. Add a payload as normal. +3. Run `make`. +4. Copy the resulting `build/MLO` file to the micro SD card at offset 128k - ie + `dd if=build/MLO of=/dev/sdcard seek=1 bs=128k`. + +**NOTE**: By default, the Beaglebone is configured to try to boot first from +eMMC before booting from SD card. To ensure that the Beaglebone boots from SD, +either erase the internal eMMC or hold the _S2_ button while powering on (note +that this has to be while powering on - ie when plugging in the USB or DC barrel +jack - the boot order doesn't change on reset) to prioritize SD in the boot +order. + +## Serial Console +By default, coreboot uses UART0 as the serial console. UART0 is available +through the J1 header on both the Beaglebone Black and Beaglebone Black +Wireless. The serial runs at 3.3V and 115200 8n1. + +The pin mapping is shown below for J1. + + ```eval_rst + +----------------------------+------------+ + | Pin number | Function | + +============================+============+ + | 1 (Closest to barrel jack) | GND | + +----------------------------+------------+ + | 4 | RX | + +----------------------------+------------+ + | 5 | TX | + +----------------------------+------------+ + ``` + +## Boot Process +The AM335x contains ROM code to allow booting in a number of different +configurations. More information about the boot ROM code can be found in the +AM335x technical reference manual (_SPRUH73Q_) in the _Initialization_ section. + +This coreboot port is currently configured to boot in "SD Raw Mode" where the +boot binary, with header ("Table of Contents" in TI's nomenclature), is placed +at the offset of 0x20000 (128KB) on the SD card. The boot ROM loads the coreboot +bootblock stage into SRAM and executes it. + +The bootblock and subsequent romstage and ramstage coreboot stages expect that +the coreboot image, containing the CBFS, is located at 0x20000 on the SD card. +All stages directly read from the SD card in order to load the next stage in +sequence. + +## Clock Initialization and PMIC +To simplify the port, the TPS65217C Power Management IC (PMIC) on the Beaglebone +Black is not configured by coreboot. By default, the PMIC reset values for +VDD_MPU (1.1V) and VDD_CORE (1.8V) are within the Operating Performance Point +(OPP) for the MPU PLL configuration set by the boot ROM of 500 MHz. + +When using Linux as a payload, the kernel will appropriately scale the core +voltages for the desired MPU clock frequency as defined in the device tree. + +One significant difference because of this to the U-Boot port is that the DCDC1 +rail that powers the DDR3 RAM will be 1.5V by default. The Micron DDR3 supports +both 1.35V and 1.5V and U-Boot makes use of this by setting it to 1.35V to +conserve power. Fortunately, Linux is again able to configure this rail but it +involves adding an entry to the device tree: + + &dcdc1_reg { + regulator-name = "vdd_ddr3"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + +If this port was to be extended to work with boards or SoCs with different +requirements for the MPU clock frequency or different Operating Performance +Points, then the port may need to be extended to set the core voltages and MPU +PLL within coreboot, prior to loading a payload. Extending coreboot so that it +can configure the PMIC would also be necessary if there was a requirement for +coreboot to run at a different MPU frequency than the 500 MHz set by the boot +ROM. + +# Todo +- Allow coreboot to run from the Beaglebone Black's internal eMMC. This would + require updating the `mmc.c` driver to support running from both SD and eMMC. +- Support the boot ROMs *FAT mode* so that the coreboot binary can be placed on + a FAT partition. +- Increase the MMC read speed, it currently takes ~15s to read ~20MB which is a + bit slow. To do this, it should be possible to update the MMC driver to: + - Increase the supported blocksize (currently is always set to 1) + - Support 4-bit data width (currently only supports 1-bit data width) +- Convert the while loops in the MMC driver to timeout so that coreboot does not + hang on a bad SD card or when the SD card is removed during boot. + + +[Beaglebone Black]: https://beagleboard.org/black [U-Boot Falcon mode]: +https://elixir.bootlin.com/u-boot/v2020.07/source/doc/README.falcon \ No newline at end of file -- cgit v1.2.3