From 69bf58d30e4fb807b3d06d590c3982b725786164 Mon Sep 17 00:00:00 2001 From: Mark Hsieh Date: Tue, 5 Jul 2022 20:53:56 +0800 Subject: mb/google/nissa/var/joxer: Update Joxer config to latest schematic init overridetree.cb based on the latest schematic. BUG=b:237628218 TEST=USE="project_joxer emerge-nissa coreboot" Signed-off-by: Mark Hsieh Change-Id: I22778cc2582abdc2e62d98c6b049a0fa4dd467e6 Reviewed-on: https://review.coreboot.org/c/coreboot/+/65662 Tested-by: build bot (Jenkins) Reviewed-by: Reka Norman --- src/mainboard/google/brya/Kconfig.name | 1 + src/mainboard/google/brya/variants/joxer/gpio.c | 5 + .../google/brya/variants/joxer/overridetree.cb | 286 ++++++++++++++++++++- 3 files changed, 290 insertions(+), 2 deletions(-) diff --git a/src/mainboard/google/brya/Kconfig.name b/src/mainboard/google/brya/Kconfig.name index f2f3082657..7384a95f7d 100644 --- a/src/mainboard/google/brya/Kconfig.name +++ b/src/mainboard/google/brya/Kconfig.name @@ -246,6 +246,7 @@ config BOARD_GOOGLE_KULDAX config BOARD_GOOGLE_JOXER bool "-> Joxer" select BOARD_GOOGLE_BASEBOARD_NISSA + select DRIVERS_GENESYSLOGIC_GL9750 config BOARD_GOOGLE_PUJJO bool "-> Pujjo" diff --git a/src/mainboard/google/brya/variants/joxer/gpio.c b/src/mainboard/google/brya/variants/joxer/gpio.c index d1837e5d21..ec7ef795f9 100644 --- a/src/mainboard/google/brya/variants/joxer/gpio.c +++ b/src/mainboard/google/brya/variants/joxer/gpio.c @@ -7,6 +7,11 @@ /* Pad configuration in ramstage */ static const struct pad_config override_gpio_table[] = { + /* A21 : GPP_A21 ==> USB_C1_AUX_DC_P */ + PAD_CFG_GPO(GPP_A21, 0, DEEP), + /* A22 : GPP_A22 ==> USB_C1_AUX_DC_N */ + PAD_CFG_GPO(GPP_A22, 1, DEEP), + /* B5 : SOC_I2C_SUB_SDA ==> NC */ PAD_NC_LOCK(GPP_B5, NONE, LOCK_CONFIG), /* B6 : SOC_I2C_SUB_SCL ==> NC */ diff --git a/src/mainboard/google/brya/variants/joxer/overridetree.cb b/src/mainboard/google/brya/variants/joxer/overridetree.cb index 4f2c04a57a..70021f7cb3 100644 --- a/src/mainboard/google/brya/variants/joxer/overridetree.cb +++ b/src/mainboard/google/brya/variants/joxer/overridetree.cb @@ -1,6 +1,288 @@ chip soc/intel/alderlake + register "sagv" = "SaGv_Enabled" - device domain 0 on - end + # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC. + # Bit 2 - C1 has a redriver which does SBU muxing. + # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1. + register "tcss_aux_ori" = "1" + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + + register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # UFC + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN + register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| I2C0 | TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C1 | Touchscreen | + #| I2C2 | Sub-board(PSensor)/WCAM | + #| I2C3 | Audio | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .early_init = 1, + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 160, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 157, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 152, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + }" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""Memory"" + register "options.tsr[1].desc" = ""Charger"" + register "options.tsr[2].desc" = ""Ambient"" + + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 3000, + .max_power = 6000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200 + }, + .pl2 = { + .min_power = 25000, + .max_power = 25000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + device generic 0 on end + end + end + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "20" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "180" + register "generic.reset_off_delay_ms" = "3" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 5d on end + end + end + device ref i2c3 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on end + end + end + device ref hda on + chip drivers/generic/max98357a + register "hid" = ""MX98360A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end + device ref pcie_rp4 on + # PCIe 4 WLAN + register "pch_pcie_rp[PCH_RP(4)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + chip drivers/wifi/generic + register "wake" = "GPE0_DW1_03" + device pci 00.0 on end + end + end + device ref emmc on + probe STORAGE STORAGE_EMMC + end + device ref ish on + probe STORAGE STORAGE_UFS + end + device ref ufs on + probe STORAGE STORAGE_UFS + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port2 as usb2_port + use tcss_usb3_port2 as usb3_port + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port2 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 UFC"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port7 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""CNVi Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb3_port1 on end + end + end + end + end + end end -- cgit v1.2.3