| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I3ac8dd2ba089970a18b460769dfc3fabf9395709
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39907
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Exit print_me_fw_version if CSE is disabled.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ie3f1c2a5a7f96371a0da872efc3308850c382ba7
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add an enable reset delay to avoid messages like this in the
kernel:
i2c_hid i2c-WCOM50C1:00: failed to change power setting.
This gets rid of all the warnings except one on reboot/shutdown.
That last case likely isn't fixed because the sleep command is
being sent directly from i2c_hid_shutdown(), so no ACPI routines
get to run and provide the delay. Since the machine is going down
for shutdown/reboot anyway, fixing that last case is a lower
priority.
BUG=b:145094539
TEST=Run on kohaku, switch to guest mode and log out, no errors
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I8fadf497dd09e5b95b1d74443fb0543d3555dbb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
For quite a bit now we are extending the FSP_USE_REPO option to be
available for all Intel SoCs. This results in a list being not only
hard to maintain but also prone to errors.
To change that behaviour this commit introduces the
HAVE_INTEL_FSP_REPO config option for SoCs that are supported from within
3rdparty/fsp.
If a SoC selects HAVE_INTEL_FSP_REPO the config option FSP_USE_REPO is
selected by default, but can be still deselected by the user in menuconfig.
Change-Id: I68ae373ce591f06073064aa75aac32ceca8fa1cc
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37582
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For newer Intel graphics(>=11), The DDI port max lanes are set to 4 by
default. And kernel driver no longer relies on coreboot to provide
information via DDI_BUF_CTL_A(for DDI port A) register programming.
Hence removing this code.
BUG=b:150788968
BRANCH=None
TEST=checked jslrvp and tglrvp compilation and boot.
Change-Id: I32692501b60f48a07b8fbb9bb3a755b18f4b3ea9
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39313
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is not a single mainboard anymore, it's actually three variants.
Change-Id: I66f1239abadd8bf93269d6d4617329dc4b925e8d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Make use of overridetrees, as these mainboards are very similar.
Tested on GA-H61MA-D3V, still works fine.
Change-Id: I1b587a091da631cb172eb76722958da6c7518893
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39668
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will make i945GC and i945GM splitting easier.
Change-Id: I3acc1f526056248f8fbb1778a3c381d369faf020
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I3dfa303b6aae2446fa3a1d67a6e31448277cacdb
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TEST=build with BUILD_TIMELESS=1, binary does not change
Change-Id: I56983cabfad574b970aba098a178e691c6b354d1
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Get ready to squash all the ASUS i440BX boards together.
Change-Id: Ibc9bfa4fc5b582bf658215bda298523e8ee7b36b
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Coalescing is not needed, as root port #1 is enabled. Also, update the
comments to look more like the other two variants. Note that the Intel
H61 PCH only has six root ports, so devices 1c.6 and 1c.7 do not exist.
Change-Id: I3f4bf99ceec6c77f6e1eabea9b712245afee7d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39742
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the align attribute of memranges to be represented
as log2 of the required alignment. This makes it consistent with how
alignment is stored in struct resource as well.
Additionally, since memranges only allow power of 2 alignments, this
change allows getting rid of checks at runtime and hence failure cases
for non-power of 2 alignments.
This change also updates the type of align to be unsigned char.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ie4d3868cdff55b2c7908b9b3ccd5f30a5288e62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds a helper macro POWER_OF_2 that is useful for
calculating the requested power of 2.
Change-Id: Ie70f93b6ac175699c11cae7d8f023a52cce01e88
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This initial devicetree attempts to correctly configure the status of
each PCI device. Not all required drivers are instantiated, nor are
all of the SoC options fully selected yet.
PCIe root ports are enabled and clocks are assigned.
USB ports are assigned.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I911ec08b0db3647d131113a138fb74a55612fd62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This configuration sets up all of the GPIO pads for the first rev of
the board.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4f6398808809492dcb345ccaa09e199fa35e40cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Created a new Google baseboard using Tiger Lake named deltaur, taking
volteer as a starting point.
BUG=b:151102807
TEST=make build successful
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib98f328df22f39e7d9d625a3292954881ee15b15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
We're running into more and more situations where we need to tell one
SOC type from another, and instead of rewriting them every time, just
add some helper functions to the picasso SOC directory.
Change-Id: I24b73145cdfa80c09fbe036d1fb6079696c6d013
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2051514
Reviewed-on: https://chromium-review.googlesource.com/2060904
Reviewed-on: https://chromium-review.googlesource.com/2060905
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
In order to create a working baseline all ports are being set to have
retimers. Setting the TcssAuxOri UPD to 0 in order for the SoC to not
misconfigure the ports. Volteer will need some additional changes after
this is implemented to account for ports that do not have a retimer.
This setting is in the process of being documented in the TGL EDS and we
can update once it is fully understood what this setting is changing on
the SOC side.
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on Volteer,
Connecting Type-c display should work regardless of Type-c cable
orientation.
Change-Id: I29eb0513299126ad8d1ee11ded2c771f28ad13f3
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39460
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP UPD TcssAuxOri is used for setting the IOM_TYPEC_SW_CONFIGURATION_3.
Configure TcssAuxOri to retimer enabled on the port 2 Type-C port.
This setting informs the SoC that a retimer is taking care of SBU
orientation therefore it does not need to do any flipping.
The IOM_TYPEC_SW_CONFIGURATION_3 is a bitfield that controls the aux
orientation settings for the Type-C ports. The TGL EDS describes this
setting and what each bit represents.
Reference section 3.6.5 in TGL EDS #575681
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on volteer,
Connecting Type-C display should work regardless of Type-C cable
orientation.
Change-Id: Iae356113cbdc72983f800060b1ebebe3c66b9daf
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39459
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the halvor variant of the volteer reference board by copying the
template files to a new directory named for the variant.
BUG=b:151399850
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_HALVOR
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: If4d3417ba55d56af441c99d949a196328d7a1951
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Update the GPE configuration for dw0, dw1 and dw2.
BUG=None
TEST=build and boot tglrvp
Change-Id: I8b406bcbd710e84cec91a8c2d1557902e929f7cc
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39844
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable wifi sar feature and set wifi sar name for kled sku.
BUG=b:152277272
TEST=emerge-hatch coreboot chromeos-bootimage and
verify wifi SAR load by sku-id
Change-Id: I9ee242773fd05cc2bcd7bde07da8176022827677
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Glados boards do not have an exposed serial port outside
of the servo interface. Set board Kconfig so that a default
built image with Tianocore payload is bootable and doesn't
hang due to trying to send data over a non-existant serial port.
Test: build/boot google/chell with board defaults
Change-Id: Ifad6f805e66438e2c436d9fa235d9be2ecf69179
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use it wherever the standard numbers were copied to. Bit 31 is set
at runtime unconditionally, so we don't need it here.
Change-Id: I0d853c3b8250a2c7b2d1a91985a555e4b17ad76c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39731
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9d7f8337653f93f40550a3d2886fe7b3845eac69
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Further backport the backlight-PWM handling from Skylake. Beside
configuring the PWM frequency in Hz, we also use the PCH's logic
for the brightness setting via BLM_PCH_OVERRIDE_ENABLE. Linux
would toggle it anyway and that might confuse our ASL code.
We assume that the 183Hz value that was set before for Slippy
variants was overridden by Linux with the 200Hz VBT value, like
it was for the Broadwell Chromebooks. So we set 200Hz for them
in the devicetrees. The calculated value for the T440p of 220Hz
seems sane and also matches the VBT.
Change-Id: I17dfe1a3610d5e2918c617cf5d10896692fdccb3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Adjust the defaults for Graphics Initialization so
that the "best" option for a board is selected by default.
Net effect is to select RUN_FSP_GOP over VGA_ROM_RUN
in cases where the platform supports GOP init and the
mainboard has a VBT file included.
Test: run 'make menuconfig' and check default Display
Init option for google/cyan, observe RUN_FSP_GOP is default.
Change-Id: I2184dbdd943d035d1682b3ae7bd8d005221434b1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Cyan has no VGA BIOS available (at least not publicly), so
remove related options. Disable SoC serial output by default,
since no production devices have this exposed, but leave it
as a user option so it can be selected as needed (eg,
for use with a Google debug servo).
Change-Id: Ic079a39ca5ad0ac653b52248244b94d4bfbd08a4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39872
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Chrome-EC/PD images for all glados variants need to be built
from the board-specific branch, not master. Including the default
board names serves no purpose and requires users to deselect
the "use built-in EC firmware" in order for the board to build.
Test: build google/chell with defaults
Change-Id: Ic10f11337b85035068cdc4fe8147413e6b7f57ac
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add missing port definition for the mSATA/WWAN mPCIe port,
set OC pin for internal ports to OC_SKIP, fix port
descrption for mPCIe/WLAN port, remove USB3 definition for
right type-A port as it is USB2 only.
Test: insert WiFi module into WWAN port, observe BT portion
detected and functional.
Change-Id: Ie39b99eeb0f605ff07d57c32189fb1f4183713e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The sipi_vector.S just needs to be linked as relocatable
so there is no need to invoke the compiler.
TEST: BUILD_TIMELESS=1 has the same hashes
Change-Id: I0370f1590a70cffb48c7930f6ae85956b506b09c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37193
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the sushi variant of the hatch reference
board by copying the template files to a new directory named
for the variant.
(Auto-Generated by create_coreboot_variant.sh version 3.0.0).
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SUSHI
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Ie900d09ff55e695527eafe68a5a75cd4a0b6d340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I35a1c404ff2f381d3d6bf4f2e4bbbf5429db38c3
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1961485
Reviewed-on: https://chromium-review.googlesource.com/2060905
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Pollock uses the FT5 footprint, so add the Kconfig option to
allow us to differentiate the chips.
Change-Id: Ia4663d38f1824786f14b6aa000adf27d64e70b5f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2051509
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Spec says if any object to control the power state exists, at least
D0 and D3 must be supported. And it seems Windows complains about the
missing D3 support: https://ticket.coreboot.org/issues/257
Windows reported `*** STOP: 0x000000A5` with the first parameter
`0x000000000000000D` (refers to a missing ACPI object) and the
third parameter `0x000000003353505F` which is the name of the
object in ASCII, little-endian (`_PS3`).
Change-Id: Ifa28a7c56575848e76e4a1c542866413b4c44d50
Signed-off-by: Nico Huber <nico.h@gmx.de>
Closes: https://ticket.coreboot.org/issues/257
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add struct i915_gpu_controller_info for boards to supply info needed
to generate ACPI backlight control SSDT. Hook into soc/common framework
by implementing intel_igd_get_controller_info().
Change-Id: I70e280e54d78e69a335f9a382261193c593ce430
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add framework to hook up the generic src/drivers/intel/gma ACPI
backlight control for platforms using SOC_INTEL_COMMON_BLOCK_GRAPHICS.
Add a weak function to get the struct i915_gpu_controller_info needed
to generate the SSDT, defaulting to NULL, which SoC's will override.
Each SoC will need to override intel_igd_get_controller_info, and
individual boards will need to populate the struct in order for
the backlight control methods to be added to the SSDT.
Change-Id: I993770fdcd0a28cee756df2bd6a795498f175952
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32549
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a follow-up patch to initial copy patch for Jasper Lake SoC.
Remove all Tiger Lake specfic code from Jasper Lake SoC code.
BUG=b:150217037
Change-Id: I44dc6bf55ca18a3f0c350f5c3e9fae2996958648
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39824
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a copy patch from Tiger Lake SoC code.
The only changes done on top of copy is changing below configs:
1. SOC_INTEL_TIGERLAKE -> SOC_INTEL_TIGERLAKE_COPY
2. SOC_INTEL_JASPERLAKE -> SOC_INTEL_JASPERLAKE_COPY
3. SOC_INTEL_TIGERLAKE_BASE -> SOC_INTEL_TIGERLAKE_BASE_COPY
We started with initial assumption that JSL and TGL can co-exist.
But now we see the SoC code in Tiger Lake is relying on too many
compile-time directives to make two SoCs co-exist. Some of the
differences are listed below:
-> Kconfig: Multiple Kconfig options using
if SOC_INTEL_{TIGERLAKE/JASPERLAKE}
-> GPIO: GPIO communities have their own differences.
This requires conditional checks in gpio.asl, gpio.c, gpio*.h,
pmc.h and gpio.asl
-> PCI IRQs: Set up differently for JSL and TGL
-> PCIe: Number of Root ports differ.
-> eMMC/SD: Only supported on JSL.
-> USB: Number of USB port are different for JSL and TGL.
-> Memory configuration parameters are different for JSL and TGL.
-> FSP parameters for JSL and TGL are different.
The split of JSL and TGL SoC code is planned as below:
1. Copy Tiger Lake SoC code as is, and change SoC Kconfig
to avoid conflicts with current mainboard builds.
2. Clean up TGL code out of copy patch done in step 1.
Make it JSL only code. The SoC config still kept as
SOC_INTEL_JASPERLAKE_COPY.
3. Change JSL SOC Kconfig from SOC_INTEL_JASPERLAKE_COPY to
SOC_INTEL_JASPERLAKE, dedede and jasperlake_rvp boards can
bind to SoC code from soc/intel/jasperlake. This step establishes
Jasper Lake as a separate SoC.
4. Clean up current JSL code from TGL code. This step establishes
Tiger Lake as a separate SoC.
BUG=b:150217037
Change-Id: I9c33f478a2f8ed5e2d8e7815821d13044d35d388
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add a file for generating PCIe and DDI descriptors that will be
understandable to the FSP.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaa4d81a0f2909cb66e551e34e1f3fa4725560d60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This patch moves "Display FSP Version Info HOB" print outside
of the loop to avoid getting called multiple times.
TEST=Able to see "Display FSP Version Info HOB" only once.
Change-Id: I754d5922f4dbef22656ca98c02d9f45791c8433d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39827
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Just a minimal set of board files needed to get it to boot
in 1 CPU mode.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Ie2f944964e938d8026a6d5d8a22a8449199d08aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
These header files are just placeholders. Currently FSP does not
look into any real platform-specific UPD fields anyway, so having
padding instead of real thing makes no difference.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Id123f4386124b2ceb7776ab719a9970c9c23a0e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
This adds barebones support.
What works:
* Linux kernel boots fine
* SIRQ and PCH interupts work fine (only in IOAPIC mode)
* PCH devices are usable
What doesn't:
* MP init is not there yet, only 1 CPU is up
* SMM is not supported
* GPIO is not available
* All IIO and extended bus numbers enumeration is not yet available
* Warm reset flow is untested
* MRC cache save/load
TEST=boots into Linux
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I7c987badc3c53f16ad178369c7e0906d6596e465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39713
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tioga Pass comes with AST2500 BMC which offers SuperIO functionality.
However we currently do not configure/enable SuperIO chip. As a result
system boots pretty silently on cold boot. Then FSP configures SuperIO
and resets the system so on next boot serial console does work. This
makes debugging difficult because pre-FSP output is invisible.
This patch enables bootblock to properly configure desired BMC SuperIO
port so early serial output is visible.
TEST=do a cold boot on OCP Tioga Pass, observe bootblock output starting
from bootblock.
Change-Id: Iff8e6a862858d733f529bb9b8c65e22e5ec6b521
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Change-Id: Iad0b394dea017223a5b92fff0cb4c2ed1d5a7bd7
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39402
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1.Select CHROMEOS_EC related Kconfig for variant board with
external EC support.
2.Select proper CHROMEOS Kconfigs which are required for all
variants.
3.Disable Intel EC region in case of external EC.
BUG=None
BRANCH=None
TEST=Compilation is successful for both Jasper Lake RVP variants.
Change-Id: I290b3748777e18476651101de71df9080dd3105c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39584
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board version is part of EC's EEPROM, select Kconfig item to enable
requesting the EC for board version.
BUG=b:152374066
TEST=Verified the mainboard version is from EC's EEPROM.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Idd8aceed83439cb500e2b03153e9f8ba93979ee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Change-Id: Icda241cfac7b428176515d7996a48cb01b1dc976
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39815
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7304b06d7bf34fb7126acfdef811481dc5cba598
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the icc_max for the GT-Sliced VR domain according to the
hardware design.
BUG=N/A
TEST=build
Change-Id: Ib9f7d77d144a282214e6bda8a4e836873c395487
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39804
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some commands, like ZQCS and ZQCL, use the same macro. This is because
they differ in things outside of the IOSAV_SP_CMD_CTRL registers. Also,
correct a comment that does not concur with the actual command in use.
With BUILD_TIMELESS=1, the binary of ASUS P8Z77-V LX2 remains identical.
Change-Id: Id2ff4c85f9d9db7c892b764472423cbf2e6db422
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The four CS control signals are grouped into the same nibble.
Change-Id: Iaf8d5216fdca6014be61ae2583fc963d69111571
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
It is only for Ivy Bridge, and needs to be set on certain circumstances.
Change-Id: I4093adef44fae787c96fec4b4b8c7c867786d219
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This register is specific to Ivy Bridge. This changes the binary because
the operations get reordered, but it is equivalent.
Change-Id: Ibc9127e0fc268466c13f7c5ac8d942543713ca32
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This changes the binary because the operations get reordered, but it is
otherwise equivalent.
Change-Id: I362187b2889e6f7a68bf752a23c1279cebf961f2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Expand a comment with additional information, and split it in two lines.
Change-Id: I10389a1a575833c8ecc9a79a374c1816000f5667
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
It is no longer specific to Ivy Bridge.
Change-Id: I3684e654a1b1aee308e30db739d41cf18e7ea6bd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39790
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sandy Bridge now uses the same code as Ivy Bridge. Drop the old code.
Change-Id: I4f6a71a4223194d83c0ee790d317ecdcafd664fd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The code for Sandy Bridge is a subset of the code for Ivy Bridge. Adapt
the Ivy Bridge code so that it also supports Sandy Bridge, and use it.
Tested on Asus P8Z77-V LX2, still boots with i7-2600 and i5-3330.
Change-Id: I7b78ec605aff976b9a5cdbb364a69df4b4947c6e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39737
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This field can take eight different values, depending on the maximum
supported speed for the memory when using the 100 MHz reference clock.
Change-Id: I8f2f04f9444831319d4f7bf0d246d01030b6f864
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The code is just clamping the frequency index to a valid range. Do it
with a helper function. Also, add a CPUID check, as Sandy Bridge will
eventually use this code.
Change-Id: I4c7aa5f7615c6edb1ab62fb004abb126df9d284b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Unfortunately this was noticed only after commit 0e1380683f
merged, credit to Sam McNally for spotting it. Previously
the legacy path replaced the space with a null byte and so
the expected string here is precisely "ethernet_mac" and
not "ethernet_mac ".
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: I603fad4efd6d6c539137dd714329bcea1877abdd
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39856
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end.
Adjust all the respective boards to shift back by one and
adjust drivers/net friends to remove the 'special casing'
of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
V.2: Fixup a code comment typo while we are here.
V.3: Vary special casing semantics for idx==0 => default mac addr is set.
V.4: Rework to still support the legacy path.
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: Idf83cc621a9333186dabb668b22c4b78e211930a
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:152157720,b:152459313
BRANCH=none
TEST=none
Change-Id: Ie79c3209d0be719ae1394e87efb357b84ce32840
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Orginally fetch_mac_string_vpd() has been special cased around
a device_index of 0/1 that causes a number of edge cases and
complexity when attempting to refactor to deal with the revised
VPD format. The following change prepares the ground work by
splitting up the functional into logical workers where we can
deal with each edge case in a more bounded way.
The background here is that the format for VPD has changed s.t. the
first NIC should always have a zero concat to the end. The details
of that can be found here:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: Idc886d9b0b3037c91f40b742437e4e50711b5f00
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to use early serial output we need to enable P2SB BAR0, because
that allows PCR access to PCH registers.
TEST=tested on OCP Tioga Pass
Change-Id: I476f90b2df67b8045582f0b72dd680dea5a9a275
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Refactor the code and split it into Xeon common and CPU-specific code.
Move most Skylake-SP code into skx/ and keep common code in the current
folder.
This is a preparation for future work that will enable next
generation server CPU.
TEST=Tested on OCP Tioga Pass. There does not seem to be degradation
of stability as far as I could tell.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I448e6cfd6a85efb83d132ad26565557fe55a265a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39601
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files.
When these headers don't line up with C Standard Library,
it causes problems.
Create stdio.h and stdarg.h header files. Relocate snprintf
into stdio.h and vsnprintf into stdarg.h from string.h.
Chain include these header files from string.h, since coreboot
doesn't care so much about the legacy POSIX location of these
functions.
Also move va_* definitions from vtxprintf.h into stdarg.h where
they belong (in POSIX). Just use our own definitions regardless
of GCC or LLVM.
Add string.h header to a few C files which should have had it
in the first place.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I7223cb96e745e11c82d4012c6671a51ced3297c2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Define a chip option to explicitly soft reset all enabled GPIOs to
default state.
TEST=boot FreeBSD 11.2 on PC Engines apu1, change GPIO configuration
using nctgpio module and check whether GPIOs are reset after reboot
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iae4205574800138402cbc95f4948167265a80d15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
It does not change once a frequency has been set, so store it somewhere.
Since this changes the saved data definition, update MRC_CACHE_VERSION.
As SNB will eventually use the same code, only IVB is being refactored.
Change-Id: I25b7c394abab173241fffdf57ac5c929daad8257
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
There is no need to call get_FRQ a dozen times with the same parameters.
As SNB will eventually use the same code, only IVB is being refactored.
Tested on Asus P8Z77-V LX2, still boots with i7-2600 and i5-3330.
Change-Id: Idd7c119b2aa291e6396e12fb29effaf3ec73108a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I048d1906bc474be4d5a4e44b9c7ae28f53b49d5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Instead of adding more versions of the `*pch.asl`, unify the existing
ones and allow to override the register locations via Kconfig. The
current defaults should work for Skylake and some newer platforms.
TEST=Booted ThinkPad X201s, backlight control still works.
Change-Id: I0b21d9a0288f0f8d6cb0a4776909bffdae7576f5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
The 2nd COM port's base address defaults to 0x2f8. Current software
for this system expects the port at 0x3e8.
Configure COMB to use 0x3e8 instead of 0x2f8.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ibb462bad5f0594e0b5c8dea6e02cd42d58d999ab
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Remove unused SMM_STORE space and use it for RW_LEGACY area
BUG=None
TEST=None
Change-Id: I5724b860271025e8cb8b320ecbd33352ef779660
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
The concerned GPIO is configured as an open drain at the Embedded
Controller side without an external pull-up. This causes leakage in the
PP3300_A rail. So configure the GPIO to have a weak internal pull-up at
the SoC side.
BUG=b:151680590
TEST=Build the mainboard. Ensure that there are no leakages in the
PP3300_A rail.
Change-Id: I5553cf40adb92edc0fecab5c875ec8d72063ba7b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The EEPROM layout is rather arbitrary and /just happened/. It needs a
256kbit part at least.
Change-Id: Iae5c9138e8404acfc3a43dc2c7b55d47d4147060
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36298
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
AMD's Family 17h SoCs share the same video device ID, but may need
different video BIOSes. This adds the common code changes to check the
vendor & device IDs along with the revision and select the correct video
BIOS to use.
Change-Id: I2978a5693c904ddb09d23715cb309c4a356e0370
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2040455
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Matt Papageorge <matt.papageorge@amd.corp-partner.google.com>
Reviewed-by: Justin Frodsham <justin.frodsham@amd.corp-partner.google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
AMD's Family 17h SOCs have the same vendor and device IDs for
their graphics blocks, but need different video BIOSes. The
only difference is the revision number.
Add a Kconfig option that allows us to add the revision number
of the graphics device to the PCI option rom saved in CBFS.
Because searching CBFS takes a non-trivial amount of time,
only enable the option if it's needed. If it's not used, or
if nothing matches, the check will fall through and search for
an option rom with no version.
BUG=b:145817712
TEST=With surrounding patches, loads dali vbios
Change-Id: Icb610a2abe7fcd0f4dc3716382b9853551240a7a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2013181
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Picasso and Dali need different video bioses even though they use the
same code in most other places.
The Kconfig symbol names are changed from the downstream commit to make
them more consistent with current coreboot code.
BUG=b:145817712
TEST=Build Dali vBIOS into the coreboot image
Change-Id: Ide0d061fda0abc78a74ddf97ba81fc3cf2b02e4f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/1956534
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
We should only define function to get lid switch and recovery mode
switches when CHROMEEC_SWITCHES is not available. Correct this to avoid
compilation issues
BUG=None
BRANCH=None
TEST=jslrvp code compilation is fine
Change-Id: I2445d40da1540c9d8c8c5fc845a4f38a5abf983e
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39585
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make use of the publicly-available FSP binaries and headers for Comet
Lake. Also, remove the Comet Lake header files from src/vendorcode,
since they are no longer necessary.
Change-Id: I392cc7ee3bf5aa21753efd6eab4abd643b65ff94
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39372
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add memory initialization parameters for Jasper Lake RVP boards
Jasper Lake RVP supports two variants, one with memory LPDDR4
and another with DDR4
Based on board id, mainboard will pass correct memory parameters
to the fsp.
BUG=None
BRANCH=None
TEST=Check compilation for Jasper Lake RVP and check memory training passes.
Change-Id: Idc92363a2148990df16c2068c7986013d015f604
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39195
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The chip.h for this driver was updated to add a reset GPIO, but did
not add the required #include of <arch/acpi_device.h>. This likely
still compiled because other chip.h files included before it may have
included it themselves.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I13200f7347fd17739a377e8ad0906ab7e5d6ae1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39677
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here.
Additionally add processor scope patching for P-State SSDT created by
AGESA, becasue AGESA creates the tables with processors in \_PR scope.
TEST=boot Debian Linux on PC Engines apu2, check dmesg that there are
no errors, decompile ACPI tables with acpica to check whether the
processor scope is correct and if IASL does not complain on wrong
checksum, run FWTS
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35f112e9f9f15f06ddb83b4192f082f9e51a969c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A bigger than zero value of bmc_boot_timeout must be set
for KCS ipmi_get_bmc_self_test_result() to run, otherwise
the self test result will be error and won't write SMBIOS
type 38 table. Here we set 60 seconds as the maximal self
test timeout.
Tested=Check if the BMC IPMI response data and SMBIOS type
38 on OCP Tioga Pass are correct or not.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I3678973736a675ed22b5bc9da20a2ca947220f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
To use Intel common block LPC function that enables the IO ranges
defined in devicetree.cb.
Tested on OCP Tioga Pass with BMC LPC working.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I675489d3c66dad259e4101a17300176f6c0e8bd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38994
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure Hyperthreading based on devicetree
BUG=none
TEST= Build and boot with FSP log and check Hyperthread setting
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Idc94e6b8ecd59a43be60bf60dc7dd0811ac0350b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39683
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The timing tables for Sandy Bridge are a subset of Ivy Bridge's tables.
Move the latter to a common place, and use it for both generations.
Tested on Asus P8Z77-V LX2 with an i7-2600 and an i5-3330, both work.
Change-Id: Id14227febf4eebb8a2b4d2d4f37759d0f42648c6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39735
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Note that pei_data.h uses the BSD 3-Clause license:
https://opensource.org/licenses/BSD-3-Clause
Change-Id: I904b343283239af4fdee583bcbea757f59a0cca7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Nuvoton NCT5104d has no LDN 0xe according to its datasheet.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0d34218d88b779b08c380d2396ff9ab9253597fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Enable ASPM L0s and L1, Common Clock and Clock Power Management for
all PCIe ports.
TEST=boot Debian linux and check new PCIe capabilities appear in lspci
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0a4c83731742f31ab8ef1d326e800dfdc2abb1b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PC Engines apu2 had many problems with PCIe cards detection. The cards
were inconsistently detected when booted from G3, S5 or after a reboot.
AGESA can reset PCIe slots using GPIO via callback. Use it to reset the
slots that support using GPIO as reset signal.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I8ff7db6ff85cce45b84729be905e6c895a24f6f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `link_frequency_270_mhz` setting was originally used by the native
graphics init code for Sandy/Ivy Bridge, which is long gone.
The value of this information (which board had it set) is questionable.
The only board that had an LVDS panel and set it to 0 was the ThinkPad
L520, where native graphics init was never reported to work. Also, the
native graphics init only used it for calculations, but never confi-
gured the hardware to use a specific frequency. A look into the docu-
mentation also doesn't reveal any straps that could be used to confi-
gure it.
Change-Id: Ieceaa13e4529096a8ba9036479fd84969faebd14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PWM-granularity chicken bit in the Wildcat Point and Lynx Point
PCHs has actually the opposite meaning of the one for Sunrise Point
and later. When the bit is set, we get a divider of 16, when it's
unset 128. Flip the bit!
Change-Id: I1dbde1915d8b269c11643a1636565a560eb07334
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I9012394e553211abe4b225beb9150d997d0c2e38
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TEST=Booted ThinkPad X201s, backlight control still works.
Change-Id: I8ff3493be4dc8d640a511358a5324eb73eb35db9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
