| Age | Commit message (Collapse) | Author |
|---|
|
Add igd device name in soc_acpi_name(), and src/drivers/gfx/generic
can generate device in GFX0 scope in SSDT.
BUG=b:277629750
TEST=emerge-rex coreboot then check SSDT on DUT
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: Id7a136b5234cf5c0f60ecf253ee78c123f1f573b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Being a static function, compiler is already putting its contents
in sdram_initialize(), its only caller.
Change-Id: Ie74d2283ef672a267d6a0c66d94aa0610f36c4f1
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74033
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With RAM init debug messages enabled, debug messages take up a lot of
flash space in romstage, with many repeated verbiage. By breaking
them up and factoring out the common verbiage, made possible with
printk(BIOS_DEBUG, "%s", ...), compiler can help deduplicate things
and make the romstage smaller.
When building for asus/p2b-ls with CONFIG_DEBUG_RAM_SETUP, this patch
shrunk romstage by 152 bytes.
Change-Id: I66e39e7901efbeb5ab72494ac02fc4d5e687c3a3
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The rationale behind this change is that multiple nested bridges using a
lot of bus numbers and IO resources is not likely to be a common hotplug
setup. When there is a large amount of hotplug ports using 32
subordinate busses results in boot failures (e.g. make qemu). 8K IO
busses for hotplug devices is also excessive in most use cases when only
64K is available in total (again make qemu results in failure to
allocate resources but does boot to payload).
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I8371958037d479e7d2053f49814735e15461ca6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74774
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch drops the assert check around
`FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN` config to ensure
`fsp_get_pch_reset_status()` can be used by all other FSP APIs to know
the status of the pending reset.
As per recent debug it has been found that, FSP is accumulating all
platform resets and executing a single reset from FSP Notify Phase.
As coreboot skipped calling into the FSP Notify APIs hence, it might
have missed the scope to issue the platform reset.
Going forward coreboot needs to implement the corresponding logic to be
able to identify any pending platform reset request and execute to
complete the silicon initialization flow.
BUG=b:282266168
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2c9e37fadc27eab820a3121e47e09529de34d10e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75309
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Phoenix has one more Type C port and two more USB2 ports which are used
as the legacy USB part of the two USB4 ports. The USB struct version
numbers have also changed, since it's a newer and incompatible version
of that struct.
TEST=After changing FSP to not hard-code the USB PHY config, but use the
configuration provided by coreboot, and applying this patch, the USB
connector on the USB2 port 4 lines works.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If52934595dd612154b97e7b90dbd96243146017a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73379
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Before the bootblock stage starts setting up the CAR mode, it sends
`POST_BOOTBLOCK_CAR` POST code. However, before the definition for
`POST_BOOTBLOCK_CAR` was introduced in the commit
0d34a50a360228138ade623e799b03eaba83b0a5 , the value `0x20` was used.
At that point, `0x20` means "entry into CAR mode" and `0x21` means
"the cache memory region is cleared". Right now we are sending the
same POST code twice, which makes no sense.
So we can do the following (todo: drop me after we decided which one is
more appropriate):
1) Drop it (current patchset does exactly that)
2) Introduce POST code similar to POST_SOC_CLEARING_CAR and use it
before the cache memory region is cleared.
Change-Id: I5d9014c788abdf5a4338c9e199138d1e514450b3
Signed-off-by: Alexander Goncharov <chat@joursoir.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Things with prompts should not use selects, but should instead default
to y. If there's a reason they need to be selected, they should be able
to be hidden when they're selected.
This isn't one of those cases where a select is needed, so set the
default to y instead.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If6de339c3a1ceb3cd71008402bba49b5efc4af3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The SPD format in the APCB has changed for Phoenix, and the injection
tool 'apcbtool' needs to be updated to match. Until this happens, the
APCB will be built containing the correct SPD.
BUG=b:281983434
TEST=Build
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If575f98511c796e93c5a12cd450a3a7985e39806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
i440BX datasheet says all memory errors reported during RAM init
should be ignored. Do as it says.
Change-Id: Iaf85fde813aa083ae62218a2df5aec303e3c9f8c
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73952
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This hook is specifically for asus/p3b-f so its mainboard code has
a chance to put SPD away after RAM init completes. What it intends
to do is done when GPO gets programmed in ramstage (and it's safe
to do so), and no other board needs this hook, so drop it.
Change-Id: Ib7874b4d2b69fdaa5f3c5a3421a62a629c4154a4
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Make ACPI code print a debug warning message when a timeout is
detected in a loop waiting for a condition.
This timeout message won't be displayed when this function is used as
delay loop (ie. without checking variable condition).
The following is required to get this log in kernel log buffer:
echo 1 > /sys/module/acpi/parameters/aml_debug_output
Here is an example of generated code when waiting for variable L23E to
be 0.
Local7 = 0x08
While ((Local7 > Zero))
{
If ((L23E == Zero))
{
Break
}
Sleep (0x10)
Local7--
If ((Local7 == Zero))
{
Debug = "WARN: Wait loop timeout for variable L23E"
}
}
BRANCH=firmware-brya-14505.B
TEST=Boot to OS and check that the Debug print is added to the
function.
Change-Id: I3843e51988527e99822017d1b5f653ff2eaa7958
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73348
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Pujjoteen5 support WWAN 5G device, add GPIO setting for WWAN 5G device
BUG=b:281943398
TEST=Build and check serial log
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ie2e0ea34c54a453645d626f892f50654ef5064ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75195
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pujjoteen5 support WWAN 5G device, enable PCIe port 3 for WWAN 5G device
BUG=b:281943398
TEST=Build and boot on pujjo
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I6d2e8eaecae968ed51095d9497beab492ba7e0c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:280843816
TEST=builds
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I55a85335a34eee227abb6ff355719f7ca2cbf04a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Code changes are necessary because `-Wformat` warns about empty
format strings by default.
Change-Id: Ic8021b70f4cd4875b06f196f88b84940c9a79fe0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75147
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I1384a02fa2931002ddd629acef0a4368435cfeb5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use ECRAM field MTNS to determine if motion sensor present, and set
TBMC device status accordingly.
TEST=build/boot google/{jinlon,drobit}, verify ACPI status for TMBC
correct for both devices with and without tablet mode.
Change-Id: Ic06ab6d721f0a3435e6dfd7b5e130f378096afec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Use AUDIO PROBE to determine speaker amp config, set SOF driver
profile accordingly.
TEST=build/boot Win11 on Delbin and Drobit, verify correct audio profile
selected, drivers loaded and functional.
Change-Id: I13d787cb5ccb74d2774151ccd5deeb45b3364319
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Some devices using the MAX98373a smart amp have the speakers connected
to port SSP2 vs the default SSP1, so add a configuration item to be
able to specify that.
TEST=tested with rest of patch train
Change-Id: I11d8011c54946aa72a83c73fa88456b4bb5d7d95
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75231
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also correct switch intendation, remove excess empty lines.
Change-Id: I86026e7f6c0c1c7f3dc6a473bb3afe2f6d32a247
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75230
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `ramtop` can be obtained from the `option.h`, so remove the
hardcoded value. Keep the check for the value being byte aligned.
Change-Id: I5327b5d4e78b715a85072e5d9a62cf8fd2ae92c0
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74511
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch overrides FSP-S UPD `LogoPtr/LogoSize` with a valid
logo.bmp file if `BMP_LOGO` config is enabled.
TEST=Able to see splash screen while booting google/marasov
with BMP_LOGO config enable.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I421da2b4dadb892f17a859ce0ec586a2880469eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75294
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch overrides FSP-S UPD `LogoPtr/LogoSize` with a valid
logo.bmp file if `BMP_LOGO` config is enabled.
TEST=Able to see splash screen while booting Intel Meteor Lake RVP
with BMP_LOGO config enable.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iaba187456dd4dfb2f69d3532e83a3850f31783ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75198
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
To match the rest of coreboot, also change this ACPI_CPU_STRING Kconfig
setting to use hexadecimal CPU numbers for the ACPI CPU objects. Since
this SoC has a maximum of 4 cores, this change will make no difference
in the runtime behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I58f9c4672f34de0defafc300d2d291f4ad6196ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75251
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Both the AMD AGESA reference code and the default coreboot
ACPI_CPU_STRING use hexadecimal numbers in the ACPI CPU object names, so
change the ACPI_CPU_STRING format string in the both the Stoneyridge
Kconfig and the common non-CAR AMD SoC config Kconfig which covers all
other AMD SoCs in soc/amd. All platforms where the P state and C state
SSDT from binaryPI (Stoneyridge) or FSP (Picasso) was used in coreboot
before it got replaced by native code, had at most 8 cores/threads, so
the mismatch never became apparent.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9d6822c5df01786ee541ce90734b75ed1a761fca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75250
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the chromeec driver to use the EC host command API. Large blocks
of repetitive code to set up EC calls are replaced with single function
calls to perform the same operation.
BUG=b:258126464
BRANCH=none
TEST=booted on rex
Change-Id: I0317405b1ed0c58568078133c17c8cfbc7c21d80
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73325
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The new util/chromeos/update_ec_headers.sh utility is used to update
ec_commands.h and introduce ec_cmd_api.h from the chrome EC repo.
ec_cmd_api.h is a new file from the chrome EC repo which defines the API
for communicating with the EC. It is a companion to the existing
ec_commands.h by defining functions corresponding to EC host command
opcodes and request/response struct definitions.
See $EC/docs/ec-host-command-api.md for details.
Generated using update_ec_headers.sh [EC-DIR].
The original include/ec_commands.h version in the EC repo is:
3e35858003 ec: Add another #line directive
The original include/ec_cmd_api.h version in the EC repo is:
59de61f2db zephyr: Add support for RNG devices
BUG=b:258126464
BRANCH=none
TEST=none
Change-Id: I30f20e34d31b7e19cf03f65fefd58ae64eef1d41
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73324
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Traditionally, display init during vboot "verified/secure/normal
boot mode" relies on the VB2_CONTEXT_DISPLAY_INIT. This is the
default behavior for vboot, meaning skip display init during verified
boot mode.
However, if the intention is to show the OEM splash screen (using
BMP_LOGO config) during boot, then the policy enforced by vboot needs
to be overridden. This can be done by setting the BMP_LOGO config flag.
If BMP_LOGO is not enabled, then the vboot policy will be followed and
display init will be skipped.
This change was made to allow OEMs to show their splash screen during
boot, even if the system is in verified/secure/normal mode.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ice1f02ad5c02a6a7e74a97ed23c5f11c7ecfb594
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75197
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Generate formatted string and ACPI code to print debug string.
For example (with pcie_rp = 1):
acpigen_write_debug_sprintf("calling _ON for RP: %u", pcie_rp);
generates the following ACPI code:
Debug = "calling _ON for RP: 1"
With this new function, the following functions are not needed anymore
and therefore are removed by this patch.
- acpigen_concatenate_string_string()
- acpigen_concatenate_string_int()
- acpigen_write_debug_concatenate_string_string()
- acpigen_write_debug_concatenate_string_int()
BRANCH=firmware-brya-14505.B
TEST=Add above functions in the acpigen code and check the generated
SSDT table after OS boot. Check the debug messages is in the
kernel log when /sys/modules/acpi/parameters/aml_debug_output is
set to '1'.
Change-Id: Id4a42e5854516a22b7bc4559c2ed08680722c5ba
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Zhixing Ma <zhixing.ma@intel.com>
Reviewed-by: Musse Abdullahi <musse.abdullahi@intel.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Fix the error below when running a coreboot image built with
`CONFIG_UBSAN=y`.
PCI: pci_scan_bus for bus 00
shift out of bounds src/arch/x86/include/arch/pci_io_cfg.h:13:20
ubsan: unrecoverable error.
GCC with `-fsanitize=shift` also flags this:
runtime error: left shift of 1 by 31 places cannot be represented in type 'int'
So, make the constant unsigned.
TEST=emulation/qemu-i440fx with `CONFIG_UBSAN=y` stops later with
[ERROR] unaligned access src/lib/rmodule.c:152:27
[EMERG] ubsan: unrecoverable error.
Change-Id: Ib05d225ab9f22078d765009b4ee6ef0c63231eed
Found-by: UBSAN
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Specifying types without addresses for PM1B events is
not useful.
Change-Id: I839208eaecf689a32484b9154647fc66633e5eef
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I56ffb82ec417530527ea1ea7e97a593e5bf6b756
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Taniks uses a 4-channel output config, rather than 2-channel.
Update the SOF speaker topology accordingly.
TEST=build/boot Win11 on taniks, verify speaker output functional.
Change-Id: I3c08b12b11464dcada014289174e0cc468d1c39d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Will allow boards using this speaker configuration to correctly specify
their output type.
TEST=tested with rest of patch train
Change-Id: Iefcfc928e2611f533af1a2962ec2761ec1b7bf3a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch adds the `__printf' macro to comply with checkpatch
following warning:
Prefer __printf(1, 2) over __attribute__((format(printf, 1, 2)))
BRANCH=firmware-brya-14505.B
TEST=Successful compilation with `__printf(1, 2)' instead of
`__attribute__((format(printf, 1, 2)))'
Change-Id: Ic2d90478ab0955c2ad0955e8cff5be76bfb2e741
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75159
Reviewed-by: Cliff Huang <cliff.huang@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
By moving certain FW UI assets from RO to RW sections, 4 MiB is
sufficient for RO section. Split the resultant available 4 MiB equally
between 2 RW sections. This will help in getting to 16 MiB SPI flash for
the mainboard.
BUG=b:281567816
TEST=Build Myst BIOS image with the updated layout.
Cq-Depend: chromium:4519688
Change-Id: I09948ceac0a6a1cb109322fc4856b8b486318664
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75184
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Update USB port macros:
- change onboard ports to SHORT: MYSTIC LIGHT, LAN_USB1, PS2_USB1,
HUB to USB 2.0 headers, HUB to rear USB 2.0
- change USB type C header to LONG which caused hard lockups on the
port making it unable to enumerate in UEFI Payload and Linux
- add empty definitions for USBr ports
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I91198aa713e9084ff3906c267ee1b37b10c71843
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69820
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
copy from dibbi since taranza base on dibbi,this is only for first
initial configuration, will update the more setting afterward.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia319f65897c0fea2f0558c20a5bc36bb6fbaea96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I6bbb67ccdd8ebc21719921d00320907f8dbb285f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74933
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since it's not obvious, add comments to acpigen_resource_word,
acpigen_resource_dword and acpigen_resource_qword to clarify out what
the magic number in byte 0 means. The most significant bit of byte 0
indicates if it is a small or large resource data type. In the case of
the MSB being 0, it's a small resource data type (aka type 0), and the
other bits encode bit the type and size of the item; if the MSB is 1,
it's a large resource data type (aka type 1), and the other bits just
encode the type and there are two separate bytes to encode the size.
Beware that the large resource's data type values in the ACPI
specification don't include the MSB that's set, but only the 7 lower
bits.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6a6c9fb1bcde232122bb5899b9a0983ef48e12b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
In practice hardware can use larger numbers.
Change-Id: I6e9ddd1ebd396c37e25eb3019f981d45d9c5e062
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki.2011@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch adds support for variant specific chip config update similar
to commit 061a93f93d2 ("mb/google/brya: Add variant specific soc chip config update").
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I60a4042cba608fd527527af9340ec0215f3086ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75046
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
add initial devicetree config for screebo
BUG=b:276814951
TEST=emerge-rex coreboot
Change-Id: Ie64d0e50ec22b3e363597af64eb723ef1f86dfa8
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The detachable Starmie will use MIPI panels, which require reading
serializable data from the CBFS. So we add MIPI panel support to the
display configuration and align the configuration sequence with the
panels that use MIPI bridges.
The PMIC Datasheet:
TPS65132-Single-Inductor-Dual-Output-Power-Supply.pdf
BUG=b:275470328
BRANCH=corsola
TEST=emerge-corsola coreboot chromeos-bootimage and display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I6f079e54f0317ff2f685f0e3834ebd1ceb8e9fcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Error message ´Cannot map compressed file config without cbfs_cache' is reported.
Compressed parts of CBFS can not be used during bootblock stage.
Remove config from mb_log_list.
Will be added to verified items by CB:74752.
BUG=NA
TEST=booting and verify log on facebook FBG1701
Change-Id: Iacf023bc8b9c2ebc66137c4ea683589751a30d2f
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add wifi sar table for uldren
BUG=b:279679700
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I9e3d7a06beb673b204f2dfe8e7beb919730aa885
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:278022971
TEST=verified on screebo
Change-Id: I16f1d66ca7f885120358eb2a2d3c6fb111319f11
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75173
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the default soft fuse bits to the recommended values
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I2354aefe90a08eaef95a68926806d11a9118c3de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
When using a 32-MiB ROM chip, the ABL leaves the SPI flash in 4-byte
addressing mode, so ensure the driver exits that mode for regular
operation.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9a846be743a65ffe5b3ef94e20e0b5fc5e273961
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Locate it with all the other PM IO registers.
Change-Id: I779b2e313c9d8370c66c4adb4f6f4d4cf5b4e7dd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
By ACPI specification, those follow GPE0_EN bits in the register space.
Use sizeof() to replace the 2/4 offset previously used.
Change-Id: I27ada0b19b2cf5e8eca71f48bf103dcab1b3cc11
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TPM IRQ should be A20 not A13. RAM table is correct.
BUG=b:282164589
TEST=able to boot up
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I82a709cc280288d612c65697b8da3c4274d4cd3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75191
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow schematic to correct I2C bus.
BUG=b:282164589
TEST=able to boot up
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I277e5190302c98dbce809d09c1a32fac758aa8e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Add _STA field entry for r8168 ACPI device and set to
ACPI_STATUS_DEVICE_HIDDEN_ON in order to hide device from
OS (Windows) as there is no driver needed (or available).
Windows correctly attaches drivers to the PCIe device, the
separate ACPI device is unused and unneeded.
Linux is unaffected as it does not use the ACPI device status.
Change-Id: Ib7ae99fffcb00e71421b93c2794119841aa239d3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75177
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach. Change the interrupt type
from EDGE to LEVEL.
TEST=build/boot samsung/lumpy, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: Ie4268b4de5779ee148699c7bef8c700a99816f1e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach.
TEST=build/boot google/parrot, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: Ic164244eceb52221653bd60f7217f9a09e38c1b6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75180
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach. Change the interrupt type
from EDGE to LEVEL.
TEST=build/boot google/butterfly, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: I971795becfb05fb42921ff6f40a20892f4f5654a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use board-specific ASL for PS2-attached trackpad rather than the EC/SIO
default, so that Windows installs a multitouch-capable driver rather
than the standard PS2 mouse driver.
TEST=build/boot Win11 on google/stout, verify trackpad is multitouch
capable.
Change-Id: Id93bbe53f35b1e2c35e36d8175889786b9f5de8b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75176
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add _HID to parent SIO device so Windows can find the PS2K, and
remove _ADR since HID and ADR are mutually exclusive.
TEST=build/boot Win11 on samsung/lumpy, verify keyboard functional.
Change-Id: I7b6b09da1a3fdc34ef43789c699f7fd22b4b655b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add _HID to parent SIO device so Windows can find the PS2K, and
remove _ADR since HID and ADR are mutually exclusive.
TEST=build/boot Win11 on google/butterfly, verify keyboard functional.
Change-Id: I772ceef1b439cfd4e2740e53362bee9d494fb36d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In ACPI 1.0 the processor objects were inside the \_PR scope, but since
ACPI 2.0 the \_SB scope can be used for that. Outside of coreboot some
firmwares still used the \_PR scope for a while for legacy ACPI 1.0 OS
compatibility, but apart from that the \_PR scope is deprecated.
coreboot already uses the \_SB scope for the processor devices
everywhere, so move the \_SB scope out of the ACPI_CPU_STRING to the
format string inside the 3 snprintf statements that use the
ACPI_CPU_STRING.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: I76f18594a3a623b437a163c270547d3e9618c31a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Don't set bit 2 of the return value of the _STA method in order for
Windows not to show a warning about an unknown device in the device
manager for this device.
TEST=The unknown device with device instance path ACPI\AMD0040\3
disappeared from the device manager in Windows 10 build 19045 on a
Mandolin board with a Picasso APU.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If005f06843956004c281fd70cf364171148cb9ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68962
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 396fb3db74db ("soc/amd/*/acpi/mmio.asl,sb_fch.asl: hide AAHB
device") didn't only change the visibility of the device, but also
changed the _STA method to a name. While this worked, the specification
says that _STA is supposed to be a method, so change it back to being a
method.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id0932b2875aaf563a4dbd860bdd11a04272e3780
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75169
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Clang complains about this.
Change-Id: I2d761d2fa946f171033220ab7b2e399cf359782a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I5738e73f2121e2558831fbaa9c92a2fd0926ad88
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
One some codepaths ucDoneFlg is not initialized. This fixes a clang
warning.
Change-Id: I78aa2c711626b24f003f5c95b1c9598eaff7cb1b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Clang warns about this.
Change-Id: I9a19f33df64a63e51e3dadac4aae28a8bb12121d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Clang warns about this.
Change-Id: I4310737bd63728d3c592d0f4d1030bc352afa575
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Clang warns about this.
Change-Id: I18ff23c3c18b7cd74f0d6fe0b308b9096ce269ae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The clang compiler warns about this.
Change-Id: I1584258aa24d6a0bf558b3c622bc53c156a37b09
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
TEST: BUILD_TIMELESS=1 remains the same.
Change-Id: I740b59574303145fc673a97556367daefe8d1540
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74540
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The clang compiler is confused about adding integers to strings. Adding
brackets around the macros fixes this.
TEST: BUILD_TIMELESS=1 remains the same.
Change-Id: I2ea17322352d977bf0ec3ee71b14463fa218d07c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74541
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Clang warns about unsigned comparison below 0. Use the enum value itself
to fix this warning.
Change-Id: I12fccff2fb7d43fd4582afd518a7eab632908a5f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74553
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
TEST: BUILD_TIMELESS=1 binary remains the same.
Change-Id: Ic05a9819764c03184b54c4fc58dbe325fddeae10
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The binary does change on these with BUILD_TIMELESS.
Change-Id: I45d51d53f991556cedd1cc45997d76fc828bceb5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74544
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
VMX is enabled through a bit in the IA32_FEATURE_CONTROL MSR, which can
be locked. The MSR remains locked after a non-power cycle reset, though.
If the MSR is locked, coreboot bails out and leaves VMX in the state it
was found. Because of this, changes to the VMX enable option in the BMC
only take effect after the system is power cycled.
This behaviour is highly undesirable because users are likely not aware
that a power cycle is required for changes to VMX state to take effect.
So, if VMX is supported, the IA32_FEATURE_CONTROL MSR is locked and the
current VMX state does not match the requested state, then issue a full
reset. This will power cycle the system and unlock the MSR, so that the
desired VMX state can be programmed into the MSR. This is checked early
to avoid needlessly doing time-consuming operations (running FSP) twice
if we know we will need to power cycle the system anyway.
Note that a user may change the VMX setting after the newly-added check
but before the setting is read in ramstage to program the MSR, but this
is a non-issue as firmware settings need a reset to take effect anyway.
TEST: Toggle VMX setting in BMC and reboot without power cycle, observe
coreboot automatically issues a power cycle reset because the MSR
is locked and the VMX state differs. Verify that the system boots
properly with VMX in the correct state after having power cycled.
Change-Id: Id9061ba896a7062da45a86fb26eeb58927184dcb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Instead of having the maximum number of possible CPU objects defined in
the DSDT, dynamically generate the number of needed CPU devices in the
SSDT like it's done on all other x86 platforms in coreboot.
TEST=APU2 still boots and Linux doesn't show any ACPI errors with this
patch applied and it prints "ACPI: \_SB_.P000: Found 2 idle states".
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id6f057ad130a27b371722fa66ce0a982afc43c6c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73073
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Instead of having binaryPI generate a PSTATE SSDT that uses \_PR_ as the
scope for the CPU objects and patching this SSDT in coreboot to use the
\_SB_ scope in patch_ssdt_processor_scope, request binaryPI to use the
\_SB_ scope instead by setting the late platform configuration option
ProcessorScopeInSb to true.
TEST=APU2 still boots and Linux doesn't show any ACPI errors with this
patch applied and it prints "ACPI: \_SB_.P000: Found 2 idle states".
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I411201b55cfee30ae41da4e6814679bdb49e9bf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73386
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I62b7390c2de244cce169550e9b1fa41af738525d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75037
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I1c995d942fa25a9268fbf716034335937df57714
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75036
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
This fixes clang warnings.
Change-Id: I407da6ec05ef646f61bd81e314fee1b5ea659192
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74557
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
TEST: BUILD_TIMELESS=1 remains the same.
Change-Id: Id2cb37dbe4d450fe7f91a527b5cd73ac55863548
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74542
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The `get_board_settings()` function always returns non-NULL, so there is
no need for NULL checks. When only one member is accessed, also drop the
local variable and directly dereference the function's return value.
Change-Id: I4fc62ca2454f4da7c8ade506064a7b0e6ba48749
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75140
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
1. Restore the reverted 'commit 059902882ce5 ("drivers/ocp/ewl: Add EWL
driver for EWL type 3 error handling")'.
2. Print more EWL type 3 error information when it occurs.
Change-Id: Ib83b7653a839d18a065b929127549acd10bce7a7
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jon.zhixiong.zhang@gmail.com>
|
|
This mainboard contains in addition to its base variant, mc_ehl2, an LCD
panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c.
BUG=none
TEST=Boot with the LCD panel attached and observe whether the picture is
stable and free of artifacts coming from wrong resolution and timing.
Change-Id: I196d7ceeb7ac241c9b95db2ef791a5f3ff7890a7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard is based on mc_ehl2. In a first step, it contains a copy
of mc_ehl2 directory with minimum changes. Special adaptations for
mc_ehl5 mainboard will follow in separate commits.
Change-Id: Id80f8eb49dd2fed0ed1ffc479d47d8669eca84c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Based on touchscreen product spec.
For uldren variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard).
BUG=b:279989974
TEST=Build and boot to OS in uldren. Touch screen is workable.
Change-Id: Ib1b1ce80aa1dd8c312e3663fc50c9e9f53cc07fe
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74835
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Replace `memupd->FspmConfig.` with `mcfg->` for the sake of brevity.
Change-Id: If2e7cccca955b0c1e07c1ecf100d29a923107856
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75136
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
This signal isn't functionally being used and is causing leakage
during suspend. Set it to NC.
BUG=b:279762779
TEST=builds. WWAN functional.
Change-Id: I93f2b0a781e250678280b57e4ab1d80ef27ff460
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The patch defines enum type for MKHI group IDs and ME SKU types instead
of macros.
TEST=Build code for Rex
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I102e802938a6a664a43a362d90a26755cff8f316
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
Having `_cmos_offset` in a CMOS offset is superfluous; remove it
so the CMOS entry is just `ramtop`.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ibc1e7d78d2e3ae04330d19e64c3437ff07060ea8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
If reading the serial/part number fails, returning an empty string is
very confusing. Instead, return "INVALID" to make problems obvious.
Change-Id: I3c174ca76d51b44456c7b68f4fcffb4c8f9379be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
The Realtek RTL8111F NIC is currently not defined at all, nor as a child
device, resulting in the on_board flag not being set to 1. This means
that Linux / udev will call the device enp3s0 rather than eno0, as it's
appropriate for on-board ethernet devices.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I95f01a466a59234d1cbe2420f208bf58ae28fcc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This board has a TPM connector, enable support for it.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I1861df95eef15bc2bd29412240d61456eaaad8c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Small typo in brask/gma-mainboards-ads
Should be brask/gma-mainboards.ads
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds
Change-Id: I9800870dcef13a3e16f6235137e79234a5e6bf83
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75052
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add the acpigen_resource_io helper function to generate an I/O range
resource.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I177f59b52d4dbbff0a3ceeef5fc8c7455cef9ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
Add the acpigen_resource_bus_number helper function to generate a bus
number range resource.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ib1f1da3dbe823c6bc4fc30c0622653410cfbf301
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
Adds the option to set the 'DmaProperty' in the device's _DSD.
This can be done by setting "add_acpi_dma_property"="true". If not set
(or set to false), the device descriptor generation behavior will remain
unchanged. The naming convention for the config option was chosen to
match that of other drivers.
This partially reverts commit 5609f7a684c6 ("drivers/pcie/generic: Clean
up driver") as the driver is now used on a couple mainboards which need
the DmaProperty.
Change-Id: I996fe4923948d13a20bf8b6b1a93dab0866d0fd4
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
In GEN_PMCON1 (Offset 1020h), Bit 0 is the "After G3 Enable" (ag3e)
(source Intel document #569262). Only use 8 bits, in the same way as
most other Intel SOCs do, for pmc_soc_set_afterg3_en.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Idb290d1480b03cb3425edc6ff29b9c78a6545df1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74955
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
