summaryrefslogtreecommitdiff
path: root/src
AgeCommit message (Collapse)Author
2019-02-07mb/google/{hatch,sarien}: Configure GPIOs using cnl_configure_padsFurquan Shaikh
This change uses cnl_configure_pads to configure GPIOs in ramstage so that cannonlake SoC code can re-configure the GPIOs after FSP-S is run. This is just adding a workaround until FSP-S is fixed. BUG=b:123721147 BRANCH=None TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch. Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/31251 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2019-02-07soc/intel/cannonlake: Configure GPIOs again after FSP-S is doneFurquan Shaikh
FSP-S is currently configuring GPIOs that it should not. This results in issues where mainboard devices don't behave as expected e.g. host unable to receive TPM interrupts as the pad for the interrupt is re-configured as something else. Until FSP-S is fixed, this change adds a workaround by reconfiguring GPIOs after FSP-S is run. All mainboards need to call cnl_configure_pads instead of gpio_configure_pads so that SoC code can maintain a reference to the GPIO table and use that to re-configure GPIOs after FSP-S is run. BUG=b:123721147 BRANCH=None TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch. Change-Id: I7787aa8f185f633627bcedc7f23504bf4a5250b4 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/31250 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2019-02-07soc/intel/cannonlake: Add Whiskeylake SoC kconfigSubrata Banik
This patch performs below tasks 1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig. 2. Allow required SoC to select this kconfig to extend CANNONLAKE SoC support and add incremental changes. 3. Select correct SoC support for hatch, sarien, cflrvps and whlrvp. * Hatch is WHL SoC based board * Sarien is WHL SoC based board * CFLRVP U/8/11 are CFL SoC based board * WHLRVP is based on WHL SoC 4. Add correct FSP blobs path for WHL SoC based designs. Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31133 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-06Makefile.inc: Create a default SMMSTORE regionArthur Heymans
Change-Id: I7b7b75050e0139ea9a0a4f2ad3c0d69a482fb38b Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/30421 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-02-06mb/google/hatch: Configure I2C busesFurquan Shaikh
This change enables I2C bus 2, 3 and 4 in devicetree and configures GPIO pads for the same. It also configures pads for I2C5 as no-connect. BUG=b:123711244 TEST=Verified that i2c shows up in "i2cdetect -l" after booting to OS. Change-Id: Ib4714a670d73228332115415e4393f82802c6475 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/31237 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-06mb/google/reef: Expand the coreboot RO sectionMathew King
Current coreboot size is not adequate for adding new features. Note for cros: This change is for merge to ToT only and should not be cherry-picked into reef's firmware branch. BUG=chromium:903833 TEST=emerge-reef coreboot Change-Id: Ie7a25c4638c474e81fb34b57de0dfc1bf393ea67 Signed-off-by: Mathew King <mathewk@chromium.org> Reviewed-on: https://review.coreboot.org/c/31230 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-06libgfxinit: Add options to limit framebuffer sizeNico Huber
Add maximum width and height options and set the default to 2560x1600 (WQXGA). The framebuffer will be scaled up to the displays' native resolutions. So this should help with tiny fonts on high-DPI displays. For laptops, reasonable defaults can be set at the mainboard level. Change-Id: I47fba063629260c3a2854caf7a73f1a1e933d063 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/30585 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-02-06Hook up Kconfig Ada spec fileNico Huber
We generate a $(obj)/cb-config.ads once and copy it per stage that uses it to $(obj)/<stage>/cb-config.ads (to simplify the gnat-bind step). The Ada package is called `CB.Config`. As there was no `CB` package yet, add that too. Change-Id: I963a6517ef4bcf84f2c8e9ae8d24a0d6b971d2b0 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/30584 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-02-06nb/intel/gm45: Use a common romstageArthur Heymans
This moves a lot of the common romstage boilerplate code to a common location, while adding a few mainboard specific hooks. Another difference is that the settings for enable_igd and enable_peg are now based on the static devicetree settings. Change-Id: I30ef7f6962aabde78b5c40e0b53bb85e01c254c1 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/31190 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-02-06mb/lenovo/x200/gpio.c: Unclutter the codeArthur Heymans
Some settings don't make sense like specifying input/output on native ports or high/low on input ports. Change-Id: Ib37837b9cdb8bb05e2523e0c43cc71fe4fbf243b Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/31187 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-06mb/roda/rk9: Use common code to set up southbridge GPIO'sArthur Heymans
Change-Id: I2057bf66435fd9113cdb1eef4c273f66b07a5a79 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/31186 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-02-06mb/lenovo/{x200,t400}: Set SMBUS mux using common SB functionsArthur Heymans
Change-Id: I1e9a165b722006557557058a14e9f5dac78d4538 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/31189 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-02-06mb/lenovo/t400: Remove RCBA replayArthur Heymans
his either sets unwanted or unnecessary settings. Also this RCBA replay did not even originate from the T400 as this code was copied from the Thinkpad x200 code on which this replay was already removed in 7bcd062 'mb/lenovo/x200: Remove RCBA replay' Change-Id: Iac6846d43395e342897e03c1ad31387638bcac64 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/31188 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-02-05mb/intel/coffeelake_rvp: Select CHROMEOS for CFL-U and WHL-U RVPSubrata Banik
This patch ensures to select chromeos kconfig only for required CFL-U and WHL-U RVPs supported by Intel client team. TEST=Ensure CONFIG_GBB_FLAG_FORCE_MANUAL_RECOVERY is only selected for CFL-U and WHL-U boards. Change-Id: Ib61409402a948f8d5f91130e200c45320ea13d3d Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31214 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05mb/google/sarien: Set system type for the board variantsDuncan Laurie
Select the appropriate system type for the different variants of the Sarien board. This will allow the Arcada variant to use the tablet mode feature of the Intel Virtual Button driver. Change-Id: I8a829aab012256ec196c8ec0fa298fd2bc77f2e1 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/31207 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-05ec/google/wilco: Add virtual button supportDuncan Laurie
Add an ACPI device that is compatible with the Intel Virtual Button kernel driver for reporting tablet mode state and various virtual button events that may come from the EC. This driver is used in Windows and in the Linux kernel at drivers/platform/x86/intel-vbtn.c Because of a check in the kernel driver it expects the board to define the SMBIOS enclosure type as convertible for the check at driver load time for tablet/laptop and dock/undock to work. The virtual tablet mode button will proxy the tablet mode state sent from the Sensor Hub to a SW_TABLET_MODE event in the kernel. The virtual power button is used during S0ix for the EC to wake the system with an SCI. There are separate press and release events which are sent for completeness, although the kernel driver will ignore the release event. BUG=b:73137291 TEST=Test that the power button can wake the system from S0ix. Also verify that the device is reported as laptop mode at boot. Change-Id: I0d5dc985a3cfb1d01ff164c4e67f17e6b1cdd619 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/31208 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05Kconfig: Add system type entries for common enclosuresDuncan Laurie
These are more common system types and in some cases it is important to know when a device is a convertible or a tablet or detachable instead of just a laptop. This change will select the appropriate SMBIOS enclosure type based on the selected system type. This is important for the Intel Virtual Button driver as it does a check on the SMBIOS enclosure type and only enables the tablet mode events if it is set to convertible: https://patchwork.kernel.org/patch/10236253/ Change-Id: I148ec2329a1dd38ad55c60ba277a514c66376fcc Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/31206 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-02-05bootmem: add new memory type for BL31Ting Shen
After CL:31122, we can finally define a memory type specific for BL31, to make sure BL31 is not loaded on other reserved area. Change-Id: Idbd9a7fe4b12af23de1519892936d8d88a000e2c Signed-off-by: Ting Shen <phoenixshen@google.com> Reviewed-on: https://review.coreboot.org/c/31123 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-02-05arch/x86/acpigen: wrap _PLD in a packageMatt Delco
The ACPI spec has an asl example for _PLD in the form: Name (_PLD, Package (0x01) { ToPLD (PLD_Revision = 0x2) }) When I ported this to acpigen and diffed the results I noticed that the binary blob was no longer provided within a package. The ACPI spec (section 6.1.8 in version 6.2) defines _PLD as "a variable-length Package containing a list of Buffers". This commit changes acpigen_write_pld to use a package (the one existing caller I found isn't wrapping the result in a package so it doesn't look like it was intended for the callers of acpigen_write_pld to be responsible for using a package. BUG=none BRANCH=none TEST=Verified that after this change a package is use and the result of acpigen matches what was used in the original asl. Change-Id: Ie2db63c976100109bfe976553e52565fb2d2d9df Signed-off-by: Matt Delco <delco@chromium.org> Reviewed-on: https://review.coreboot.org/c/31162 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-05acpi: device: avoid empty property list in acpi_dp_writeMatt Delco
If an acpi_dp table has children but no properties then acpi_dp_write() will write out a properties UUID and package that contains no properties. The existing function will avoid writing out a UUID and empty package when no children exist, but it seems to assume that properties will always be used. With this change properties are handled in a manner akin to children so that a UUID and package are only written if properties exist. BUG=none BRANCH=none TEST=Confirmed that prior to this change a UUID and empty package was present for a device that had children but no properties. Verified that after this change the UUID and empty package are no longer present but the child UUID and package are still present. Change-Id: I6f5597713a1e91ca26b409f36b3ff9eb90a010af Signed-off-by: Matt Delco <delco@chromium.org> Reviewed-on: https://review.coreboot.org/c/31161 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-05mb/google/hatch: Add keyboard backlight supportIvy Jian
This change adds keyboard backlight feature for Hatch platform. BUG=b:122799544 BRANCH=none TEST=keyboard backlight works when EC reports correct info. Change-Id: I29273122f061e0e442f6629351ef3670535c0507 Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/31175 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05intel/quark: Fix COMMONLIB_STORAGE in CARKyösti Mälkki
The allocation is not required before romstage, so it can be just another CAR_GLOBAL instead of polluting the linker script. Change-Id: I0738a655f6cc924fbed92ea630f85406e3f58c0b Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/31191 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05src/soc/intel/common: Clear GPIO driver ownership when not requestedKeith Short
The default state of the HOSTSW_OWN register in the PCH is zero, which configures GPIO pins for ACPI ownership. The board variabt GPIO tables can request specific pins to be configured for GPIO driver ownership. This change sets the HOSTSW_OWN ownership bit when requested and explicitly clears the ownership bit if not requested. BUG=b:120884290 BRANCH=none TEST=Build coreboot on sarien. Verified UEFI to coreboot transition boots successfully. Change-Id: Ia82539dbbbc7cf5dfb9223902d563cafec1a73e5 Signed-off-by: Keith Short <keithshort@chromium.org> Reviewed-on: https://review.coreboot.org/c/31209 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-05soc/intel/apl: Call mca_configure() on cold boots onlyNico Huber
By APL BIOS Spec, we must not do this on warm boots. The TODO comment seems stale and copied over. So the actual requirements for SGX are unknown and we add a guard for that case. Change-Id: I09b4a2fe22267d7318951aac20a3ea566403492e Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/31200 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05soc/intel/cpulib: Add debug message to mca_configure()Nico Huber
Change-Id: Idfe93e454cc0ce0d8e06e23beaddee2f11f5eedd Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/31199 Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05mb/google/poppy/variants/atlas: config GPP_D1 as no-connectCaveh Jalali
This reconfigures the GPP_D1 GPIO pin as a no-connect. It really doesn't go anywhere today or on previous revs of the board. BUG=b:110614620 BRANCH=none TEST=atlas still boots Change-Id: Iea53cf909f8f060c4e0f14e8b4ad579b838b7caa Signed-off-by: Caveh Jalali <caveh@chromium.org> Reviewed-on: https://review.coreboot.org/c/31210 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-05Revert "mb/google/poppy/variant/atlas: I2C: run trackpad at 1MHz"Caveh Jalali
This reverts commit 7696290004b6490c7ef8027d7ddf67b163e7dad8. We're seeing trackpad problems on some units with the I2C bus running at 1MHz but not at 400KHz. So, revert back to 400KHz until we understand how to make 1MHz operation more robust. BUG=b:123650686 Change-Id: Ifb06afece9eee0c153240d35e6c3001f5b74f310 Signed-off-by: Caveh Jalali <caveh@chromium.org> Reviewed-on: https://review.coreboot.org/c/31212 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-05mb/google/kukui: Add default HWID for Chrome OSHung-Te Lin
The default value for Chrome OS HWID should be different. Calculated as HWID v1. BUG=b:123336677 BRANCH=kukui TEST=build and boots properly. Change-Id: I39c640562c1c3b117292b8abacd36a4a9c2fa6c6 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/31088 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: You-Cheng Syu <youcheng@google.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-02-05cpu/x86/mtrr: Fix sign overflowPatrick Rudolph
Use unsigned long to prevent sign overflow. Fixes wrong MTRRs settings on x86_64 romstage. Signed-off-by: Patrick Rudolph <siro@das-labor.org> Change-Id: I71b61a45becc17bf60a619e4131864c82a16b0d1 Reviewed-on: https://review.coreboot.org/c/30502 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-02-05mb/emulation/qemu-i440fx: use e820 in romstageThomas Heijligen
Use memory map from fw_cfg e820 map to find cbmem_top in romstage to avoid conflicts with CMOS option table. Keep qemu_gwt_memory_size() as fallback. Change-Id: I6465085020125fc790257f09eb157030c6ceabcb Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com> Reviewed-on: https://review.coreboot.org/c/30850 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-02-05mb/emulation/qemu-i440fx: make fw_cfg_present usable in PRERAMThomas Heijligen
Change-Id: I98f1c97e3ca33a12620cdd073c76fd4e271f1fcc Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com> Reviewed-on: https://review.coreboot.org/c/30849 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-02-05mb/emulation/qemu-i440fx: add e820 interfaceThomas Heijligen
Qemu provides e820 table at fw_cfg interface. Add functions to access it. Change-Id: I547bc7fef09999baa28149a6325cbca91e31e99b Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com> Reviewed-on: https://review.coreboot.org/c/30848 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-02-05mb/emulation/qemu-i440fx: remove mm file listingThomas Heijligen
Remove memory mapped copy of the file list to use it also in romstage. fw_cfg_find_file searches directly for the file on data port. Change-Id: Ie97ed3f0c98a5bb18a35ab0eaf8c4777a53e5779 Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com> Reviewed-on: https://review.coreboot.org/c/30847 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-02-05mb/siemens/mc_apl1: Enable VTD for mc_apl2 and mc_apl5Werner Zeh
These boards need a working VTD therefore enable this feature. Change-Id: I74c64bf1bd66188c4c32b85c66683dafd0e1fd38 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/c/31195 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2019-02-05intel/apollolake: Add parameter to enable VTD in devicetreeWerner Zeh
The FSP has a parameter to enable or disable the VTD feature (Intel's Virtualization Technology for Directed I/O). In current header files for FSP-S (Apollo Lake and Gemini Lake) this parameter is set to disabled per default. Therefore, if the FSP was not modified via BCT, this feature is most likely disabled on all mainboards. Add a chip parameter so that VTD can be enabled on mainboard level in devicetree and therefore this feature can be activated if needed. Change-Id: Ic0bfcf1719e1ccc678a932bf3d38c6dbce3556bc Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/c/31194 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05mb/google/octopus: Add USB ACPI configuration for CNVi BT moduleKarthikeyan Ramasubramanian
This change enables exporting the reset GPIO for CNVi Bluetooth module to the kernel for use in an rf-kill operation. BUG=b:123296264 BRANCH=octopus TEST=Boots to ChromeOS. Checked the SSDT table to ensure that the reset gpio is exported under the device \_SB_.PCI0.XHCI.RHUB.HS09. Ensured that the kernel btusb driver is able to find the exported GPIO in the devices with CNVi BT module. Change-Id: I10f28bfe705da5104d709ae2ed91a8ae003fa639 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/31183 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-05soc/intel/apollolake: Update XHCI ports for GLK in ACPI tablesFurquan Shaikh
GLK has a dedicated USB2 port that is used specifically for CNVi BT. This requires that the ACPI tables define an additional USB 2 port which results in _ADR for USB 3 ports being different for GLK than APL. This change splits the ports in xhci.asl into APL and GLK specific ports.asl and selects the appropriate file based on CONFIG_SOC_INTEL_GLK. It also adds support for returning HS09 for GLK if ACPI name is requested for that port. BUG=b:123670712 BRANCH=octopus TEST=Verified that generated DSDT for octopus (GLK) includes HS09 and for reef (APL) does not include HS09 definition. Change-Id: I2d3d3690ec9ea1f6e35c38c3b3cbb82e961b7950 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/31172 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-05mb/google/hatch: Add USB port capability ACPI support for USB2 port10Aamir Bohra
This implementation adds support to create ACPI package for USB port capability (_UPC) and physical location of device (_PLD) for USB2 port 10. BUG:b:123375275 TEST:Verify _UPC and _PLD ACPI packages gets published for USB2 Port 10 in SSDT and BT is functional in discrete and integrated mode. Change-Id: Ifeab24505a700e8e4677be20074c7d0400769cec Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/c/31197 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-04soc/amd/stoneyridge: Reboot if missing MRC cache infoMarshall Dawson
AGESA doesn't detect invalid NV data during AmdInitResume(). In cases where the data has been erased, or cannot be found, reboot the system. Otherwise the user will experience a hang when cbmem isn't recovered and the postcar frame cannot be initialized. BUG=b:122725586 TEST=Write S3 NV save data with 0xff and force reboot Change-Id: Ib3cf2515f300decd3de198f7741660d95ee4c744 Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-on: https://review.coreboot.org/c/31160 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2019-02-04ec/google/wilco: Add ACPI device for event interfaceDuncan Laurie
Add a separate ACPI device for the Wilco EC event interface so that the OS drivers can bind to it separately. Since the event handling is all done with ACPI and not mailbox calls this will be implemented as a standard acpi_driver in the kernel. BUG=b:119046283 TEST=veriy device exists in DSDT Change-Id: I5259a926fb6d5faea835bcdefa12f0184c5adf4a Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/31204 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-04ec/google/wilco: Add S0ix support handlersDuncan Laurie
1) In the EC _REG method set the flag indicating S0ix support in the OS. 2) Add a function that can be called by the LPI _DSM method to indicate to the EC that the OS is entering or exiting S0ix. BUG=b:73137291 Change-Id: Iddc33a08542a6657694c47a9fda1b02dd39d89f7 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/31094 Reviewed-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-04sb/amd/agesa/hudson/Kconfig: Disable xHCI by default if no USE_BLOBSMike Banon
Disable xHCI by default if USE_BLOBS option has not been selected. Signed-off-by: Mike Banon <mikebdp2@gmail.com> Change-Id: I1c3f0ff49fbe3db3ef095d99055f75d65cd6f661 Reviewed-on: https://review.coreboot.org/c/31216 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-02-04superio/winbond/w83627ehg: Correct CR 0x2a commentElyes HAOUAS
Register 0x2a [Bit 1] is a PIN89, PIN90 function select for i2c Change-Id: I9231a68ec7e9a3130a6b6975544bf89ab09cb3e6 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/31185 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-02-04soc/intel/cannonlake: Remove SOC_INTEL_CANNONLAKE_MEMCFG_INIT KconfigSubrata Banik
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc. Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31134 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-02usbdebug: Use fixed size fieldKyösti Mälkki
The structure is placed inside CBMEM, one should use types with fixed size. Seems we prefer to prepare for 64-bit builds even for MMIO pointers. Change-Id: I60382664a53650b225abc1f77c87ed4e121d429e Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/31182 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-02-02usbdebug: Fix reserve in CARKyösti Mälkki
We need sizeof(struct ehci_dbg_info) of 88 but only reserved 64 bytes. If usbdebug_hw_init() was called late in romstage, for some builds it would corrupt CAR_GLOBALs like console_inited variable and stop logging anything. Also change pointer initialisation such that glob_dbg_info will hit garbage collection for PRE_RAM stages. Change-Id: Ib49fca781e55619179aa8888e2d859560e050876 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/31174 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-02-02riscv: Show hart id in trap handlerPhilipp Hug
Also show hart id in trap information for easier debugging. Change-Id: I20acf86e1af111600c158295ae03b2167838d127 Signed-off-by: Philipp Hug <philipp@hug.cx> Reviewed-on: https://review.coreboot.org/c/31201 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: ron minnich <rminnich@gmail.com>
2019-02-02riscv: Simplify payload handlingXiang Wang
1. Simplify payload code and convert it to C 2. Save the FDT pointer to HLS (hart-local storage). 3. Don't use mscratch to pass FDT pointer as it is used for exception handling. Change-Id: I32bf2a99e07a65358a7f19b899259f0816eb45e8 Signed-off-by: Xiang Wang <wxjstz@126.com> Signed-off-by: Philipp Hug <philipp@hug.cx> Reviewed-on: https://review.coreboot.org/c/31179 Reviewed-by: ron minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-02mb/ocp/wedge100s: Remove MAINBOARD_USES_IFD_GBE_REGIONPatrick Rudolph
It has 2x 10GbE XGMII and 1x i210IT on PCIe, but no GBE. Change-Id: I641c336350a0b05f3db7603cc7f6281ff3b0c388 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/31198 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
2019-02-02mb/intel/coffeelake_rvp: Enable GBE region for RVP8 and RVP11Subrata Banik
This patch ensures to enable IFD GBE region only for required CFL RVP8 and 11 supported by Intel IOTG team. TEST=Ensure CONFIG_MAINBOARD_USES_IFD_GBE_REGION is not selected for CFL-U and WHL-U boards Change-Id: If3fcd23c32f9afd2004fb176c0324f089f2ee412 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31192 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2019-02-01vendorcode/google/chromeos: Use ACPI GPIO pin when possibleDuncan Laurie
Have the generated Chrome OS ACPI GPIO table provide the ACPI GPIO pin number instead of the raw GPIO number when possible. This is necessary if the OS uses a different numbering for GPIOs that are reported in ACPI than the actual underlying GPIO number. For example, if the SOC OS driver declares more pins in an ACPI GPIO bank than there are actual pins in the hardware it will have gaps in the number space. This is a reworked version of 6217e9beff16d805ca833e79a2931bcdb3d02a44 which does not try to convert CROS_GPIO_VIRTUAL. BUG=b:120686247 TEST=pass firmware_WriteProtect test on Sarien Signed-off-by: Duncan Laurie <dlaurie@google.com> Change-Id: I3ad5099b7f2f871c7e516988f60a54eb2a75bef7 Reviewed-on: https://review.coreboot.org/c/31080 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-02-01sb/intel/common: Rename i2c_block_read() to i2c_eeprom_read()Kyösti Mälkki
Datasheets describe the used command as 'I2C Read' but adding the word 'eeprom' in between should avoid further confusion with other block commands. Followups will add a symmetrical pair of commands i2c_block_read() and i2c_block_write() that operate via I2C_EN bit and have a 32 byte size restriction on block transfers. For some hardware revision these block commands are available, while 'I2C Read' was not. Change-Id: I4494ab2985afc7f737ddacc8d706a5d5395e35cf Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/31151 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-02-01mb/google/hatch: Enable S0ixShelley Chen
BUG=b:123540469 BRANCH=None TEST=None Change-Id: I713e6ad70efdd152895afa45aee44a5b53a8136b Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/31157 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-01soc/amd/stoneyridge: Add generic PM1 register clear functionMarshall Dawson
Convert vboot_platform_prepare_reboot() to call a function in soc//stoneyridge. A subsequent patch will add another call to the new function, and this change removes any inference of a dependency on vboot. BUG=b:122725586 Change-Id: I634fcd030e206c790bda697a3dbef4e8cc21b3a8 Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-on: https://review.coreboot.org/c/31159 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-02-01soc/intel/icelake: Make correct C-state entries for S0ix and non-S0ixSubrata Banik
TEST=Dump SSDT entries to verify _CST between S0ix enable and disable. >> iasl -d SSDT # to generate SSDT.dsl Change-Id: I82d8bf9d143263a80a544f6e11186a3bc9c41052 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31153 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-01-31soc/intel/cannonlake: Make correct C-state entries for S0ix and non-S0ixRonak Kanabar
TEST=Dump SSDT entries to verify _CST between S0ix enable and disable. Change-Id: I25e8f8c13bb91c2645e8e9fdfdf9ba4d7022f1b1 Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-on: https://review.coreboot.org/c/31154 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
2019-01-31mb/google/sarien: Turn on ASPM L1.2 for Card ReaderLijian Zhao
Enable ASPM L1.2 support for embedded realtek card reader, after change the power consumption for SD controller from 5mW to less than 2mW. BUG=N/A TEST=Build and boot up on Arcada platform, check the PCI configuration on pcie root port offset 0x208 is 0x0f, and offset 0x168 on card reader is also 0x0f. Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Change-Id: I08d85ee332ceee8ed85cd816bc3e6c895528fdb0 Reviewed-on: https://review.coreboot.org/c/31145 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-31mb/google/octopus: Add Bluetooth USB ACPI configurationKarthikeyan Ramasubramanian
Enable USB ACPI driver for octopus boards and add bluetooth USB ACPI configuration in devicetree. This change enables exporting the bluetooth reset GPIO to the kernel for use in an rf-kill operation. BUG=b:123296264 BRANCH=octopus TEST=Boots to ChromeOS Change-Id: Ie40f1ad70f21a6fd398ce23d060e0c588ba6ce41 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/31130 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-01-31soc/intel/apollolake: Fix XHCI device name in ACPIKarthikeyan Ramasubramanian
XHCI is currently named as XHC1. This leads to namespace lookup error in the kernel when children USB ACPI devices are added under the scope of XHCI device. BUG=b:123296264 BRANCH=octopus TEST=Boot to ChromeOS; Ensure that the below error is resolved in the kernel dmesg [ 0.001000] ACPI Error: [\_SB_.PCI0.XHCI.RHUB.HS03] Namespace lookup failure, AE_NOT_FOUND (20170728/dswload-210) Change-Id: Ia4921547fee6fb51333319b9e881501a7e75ebce Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/31147 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-01-31mb/emulation/qemu-i440fx: prepare fw_cfg for romstage usageThomas Heijligen
Add separate functions for selecting the port and reading the port. Romstage can now read incremental from the data port. Change-Id: I0ffde3bc2a4415a8af99af2275d16f6609099e37 Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com> Reviewed-on: https://review.coreboot.org/c/30846 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-01-31mb/emulation/qemu-i440fx: change file handlingThomas Heijligen
Reduce the number of fw_find_file calls by returning the file structure at fw_cfg_check_file. The file structure can then be used to allocate memory and access the file content directly without recurrence searching. Remove now unnecessary function fw_cfg_load_file. Fixed breaking function calls and add include guard at fw_cfg_if.h. Change-Id: I48cc943aaa999e4323e9d7e5dd666c5316533dcc Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com> Reviewed-on: https://review.coreboot.org/c/30845 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-01-31google/kukui: Set GPIO_RESET to output modeTristan Shieh
In payloads, we didn't set GPIO modes. We have to set up GPIO mode in coreboot for payloads. BUG=b:80501386 BRANCH=none TEST=HW reboot works in depthcharge Change-Id: Ibd2c6c071871edc59497fbb245cdbec6a814f621 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/31148 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-31lib/hardwaremain: Fix more ACPI/IOAPIC typosSubrata Banik
CB:31139 fixs few ACPI type error. Here is few more typo mistake. Change-Id: Ieecf0ba8fe09ed5003d5ae766079b8f83cc891b9 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31152 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-30soc/intel/apollolake: Sync fsp upd structure updateJohn Zhao
FSP 2.0.9 provides UPD interface to adjust integrated filter value, usb3 LDO and pmic vdd2 voltage. Change coreboot upd structure to sync with fsp 2.0.9 release. BUG=b:123398358 CQ-DEPEND=CL:*817128 TEST=Verified yorp boots to kernel. Change-Id: I3d17dfbe58bdc5222378459723da8e9ac0573510 Signed-off-by: John Zhao <john.zhao@intel.com> Reviewed-on: https://review.coreboot.org/c/31131 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-01-30mainboard/intel/cannonlake_rvp: Enable SaGv configRonak Kanabar
This patch enables SaGv on Intel CNL-Y and CNL-U RVP board Change-Id: I8a4b8a2a365caed304935bf0d66db9a92d10c23f Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-on: https://review.coreboot.org/c/31132 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-30string: move strdup() & strconcat() to lib/string.cThomas Heijligen
Move functions not available in PRE_RAM into seperate file. Makes it easier to share code between rom and ramstage. Change-Id: I0b9833fbf6742d110ee4bfc00cd650f219aebb2c Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com> Reviewed-on: https://review.coreboot.org/c/31141 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-01-30selfload: check target memory type in selfload_checkTing Shen
Currently, selflock_check() verifies that the binary is loaded in an usable RAM area. Extend its functionality so we can also check that BL31 is loaded in a manually reserved area, and fail early if the range is not protected. Change-Id: Iecdeedd9e8da67f73ac47d2a82e85b306469a626 Signed-off-by: Ting Shen <phoenixshen@google.com> Reviewed-on: https://review.coreboot.org/c/31122 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-01-30mainboard/{google,intel}: Remove SaGv hard codingRonak Kanabar
Remove hard coding for SaGv config in devicetree.cb and apply macro for SaGv config for CNL variants boards Change-Id: If007589d5c1368602928b1550ec8788e65f70c05 Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-on: https://review.coreboot.org/c/31120 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2019-01-30mb/google/sarien/variants/arcada: Adjust TP/TS/H1 I2C CLK to meet specCasper Chang
After adjustment on Arcada EVT TouchScreen: 390 KHz TouchPad: 389 KHz H1: 389 KHz BUG=b:120584026, b:120584561 BRANCH=master TEST=emerge-sarien coreboot chromeos-bootimage measure by scope Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com> Change-Id: Ia6eb332e7a664b211a5025ad07e0d01bf7f8d5bb Reviewed-on: https://review.coreboot.org/c/31124 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
2019-01-30ec/google/chromeec: Add boardid.c to verstageYou-Cheng Syu
Modifiy Makefile so that we can get board ID in verstage. BRANCH=none BUG=b:117916698 TEST=manually Change-Id: Idcdb6e07f565c937185cab811abac0ce47e5e3a7 Signed-off-by: You-Cheng Syu <youcheng@google.com> Reviewed-on: https://review.coreboot.org/c/31006 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-01-30soc/amd/stoneyridge: Access SMBUS through MMIORichard Spiegel
Currently SMBUS registers are accessed through IO, but with stoneyridge they can be accessed through MMIO. This reduces the time of execution by a tiny amount (MMIO write is faster than IO write, though MMIO read is about as fast as IO read) as most of the time consumed is actually transaction time. Convert code to MMIO access. BUG=b:117754784 TEST=Used IO to write and MMIO to read, to confirm a one to one relationship between IO and MMIO. Then build and boot grunt. Change-Id: Ibe1471d1d578611e7d666f70bc97de4c3b74d7f8 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/c/29258 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2019-01-30siemens/mc_apl2: Change SERIRQ modeMario Scheithauer
Because of Intel's faulty LPC clock, the SERIRQ mode must be corrected. By removing this entry from devicetree, the default value (quiet mode) is used. The problem is described in Intel document 334820-007 under point APL47. Change-Id: I7a45e0e5fcde17a20abd19a33282b8a9215b1480 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/c/31138 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-30siemens/mc_apl2: Correct whitespace of devicetreeMario Scheithauer
Change-Id: Ie0e11b1ce6c6acb1b74ce1196304f7e6ac4664d9 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/c/31137 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-01-30siemens/mc_apl2: Activate TPM supportMario Scheithauer
The TPM chip is connected to the SPI interface of APL. The proper chip select pin needs to be used in order to access the TPM in the memory mapped space. This needed chip select is internally (inside APL) routable to GPIO 106. Therefore the change of GPIO 106 mode is needed to make the TPM work on SPI bus. TEST=Build coreboot for mc_apl2 board and check the TPM console output. In addition the TPM was correctly verified by our Linux driver. Change-Id: I2b0d5a6f2c230187857c2428a70de61f21da6724 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/c/31125 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-01-30mb/google/octopus/casta: Correct unused GPIO pad configurationSeunghwan Kim
Real unused GPIO pad is GPIO_123, but GPIO_122 is configured as unused pad. This patch corrects the configuration. BUG=NONE BRANCH=octopus TEST=emerge-octopus coreboot Change-Id: I4473bd66a4162f5aee3b998aacba906824728fc8 Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com> Reviewed-on: https://review.coreboot.org/c/31135 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2019-01-30mb/google/hatch: Enable AP Wake from ECShelley Chen
Initialize EC_PCH_WAKE_ODL GPIO to make sure that ec events will wake the AP from suspend. Also create a task to initialize the hostevent wake mask properly. BUG=b:123325238,b:123325720 BRANCH=None TEST=from AP console: powerd_dbus_suspend from EC console: hostevent (make sure wake mask set) from EC console: gpioset PCH_WAKE_L 0 Make sure device wakes up Also, checked to make sure keyboard press wakes up device from S3. Change-Id: I53d5291a6b9ab9a21e89ccd21f172180ce473bd5 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/31100 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-01-30sb/intel/common/firmware: Don't call GbE binary `firmware`Nico Huber
Unless things changed considerably, this file doesn't contain any firmware. It is merely replacing a configuration EEPROM for the MAC address etc. So don't call it firmware. Change-Id: Ife6190639e7f05da2cb6eddeb1b0db0e8ffc8e6e Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/31108 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2019-01-30lib/hardwaremain: Fix typo ACPISubrata Banik
Change-Id: I51493203b82868d221806c2e22b0c4b62e9fac97 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31139 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-01-29mb/google/octopus/var/phaser: Hook up Raydium touchscreenHao He
List Raydium touchscreen in the devicetree so that the correct ACPI device are created. BUG=b:121105424 BRANCH=octopus TEST=emerge-octopus coreboot chromeos-bootimage reflash the coreboot to DUT, make sure the Raydium touchscreen can work. Change-Id: I9ffb2a858f31a8b003086806de07f4079870cddf Signed-off-by: Hao He <hao.he@bitland.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/31116 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-29google/kukui: Move some initialization from bootblock to verstageYou-Cheng Syu
MT8183 only allows booting from eMMC, so we have to do eMMC emulation from an external source, for example EC, which makes the size of bootblock very important. This CL moves some initialization steps from bootblock to verstage. This will save us about 2700 bytes (before compression) / 1024 bytes (after LZ4 compression) in bootblock. In case of CONFIG_VBOOT is disabled, these initialization steps will be done in romstage. BRANCH=none BUG=b:120588396 TEST=manually boot into kernel Change-Id: I9968d88c54283ef334d1ab975086d4adb3363bd6 Signed-off-by: You-Cheng Syu <youcheng@google.com> Reviewed-on: https://review.coreboot.org/c/30331 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-01-29soc/intel/apollolake: Add GLK usb2eye configuration overrideSeunghwan Kim
Now we have usb2eye configuration register in FSPUPD, so we need to add an interface to override usb2eye setting. BRANCH=octopus BUG=NONE TEST=Verified usb2eye custom setting works Change-Id: I5c500964658072eaaf59364242aa928df25d99d1 Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com> Reviewed-on: https://review.coreboot.org/c/31060 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-01-29google/kukui: Implement HW reset functionTristan Shieh
Asserting GPIO PERIPHERAL_EN8 will send a signal to EC to trigger a HW reset for SoC and H1. BUG=b:80501386 BRANCH=none TEST=emerge-kukui coreboot; manually verified the do_board_reset() on Kukui P1 Change-Id: I9afad84af2031a766bc08fc76c8b5f55588c453a Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/31118 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-29mediatek: Separate WDT reset function from WDT driverTristan Shieh
Separate WDT reset function from WDT driver, then we can use the common WDT driver and have a board-specific reset function on different boards. In Kukui, we plan to use GPIO HW reset, instead of WDT reset. Add config "MISSING_BOARD_RESET" in Kukui to pass the build for now. BUG=b:80501386 BRANCH=none TEST=emerge-elm coreboot; emerge-kukui coreboot; Change-Id: Ica07fe3a027cd7e9eb6d10202c3ef3ed7bea00c2 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/31121 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-29cpu/intel/microcode: Enable verbose outputPhilipp Deppenwiese
* Check if microcode is really updated. * Enable more verbose output. Change-Id: I534aa790c8d37b5f1603e1715635446835513a65 Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Reviewed-on: https://review.coreboot.org/c/29864 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: David Hendricks <david.hendricks@gmail.com>
2019-01-29mb/lenovo/z61t/Kconfig: Select I945_LVDSPeter Lemenkov
This board has almost the same schematics as [xt]60 so this should work. See also commit 7971582e with Change-Id Iff6dac5a5f61af49456bc6312e7a376def02ab00. Change-Id: I8dc9b122eb64b5c1dcd0dbc99ac41aa0f8dd9766 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/c/31115 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-01-29mb/intel/icelake_rvp/../icl_y: Enable SaGvSubrata Banik
This patch enables SaGv on Intel ICL-Y RVP board. TEST=Able to build and boot to Chrome OS. Change-Id: Ic3ed94d47ddc7fd70bf3de1db15fe574029df856 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31119 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2019-01-29soc/intel/icelake: Remove unnecessary USB charging ASL entriesSubrata Banik
This patch removes stale ASL entries added in past due to chromeos requirement. BUG=115755982 TEST=Build and boot ICL platform without any problem. Change-Id: I18b57822ce3198fb96aae977f0b552ff2d4a14ee Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/31117 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-28intel/apollolake: Add IPU to disable_dev functionWerner Zeh
The SoC has an Image Processing Unit which is located on PCI 00:03.0. There is a corresponding parameter for FSP which handles enabling/disabling of this functionality (IpuEn). Add this device to the disable_dev() function of the chip so that if this device is disabled in devicetree the matching FSP parameter will be disabled as well. As this parameter is only valid for Apollo Lake, use the config switch CONFIG_SOC_INTEL_GLK to disable this code if compiled not for Apollo Lake. As this issue is regarding a missing structure member, this check needs to be done on preprocessor level and not at runtime. Test=Verified this function on mc_apl2. Change-Id: I75444bf483de32ba641f76ca50e9744fdce2e726 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/c/30992 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-01-28intel/apollolake: Add fixed resources for VTd to system resourcesWerner Zeh
If the VTd feature is enabled, there will be up to two fixed resources which are set up by the FSP. Add these resources to the list of system resources so that the PCI enumerator will know them. Change-Id: If96fc1c93746e3c7f510e5b3095ea3090e1b8807 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/c/30991 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-28soc/apollolake: Generate DMAR tableWerner Zeh
Generate DMAR table if VTd feature is enabled. Test=Booted into Linux on mc_apl2 and verified the DMAR table contents. In addition turned off Vtd and verified that no DMAR table is generated at all. Change-Id: Ie3683a2f3578c141c691b2268e32f27ba2e772fa Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/c/30990 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-01-28intelblocks/systemagent: Add ACPI table generation hookWerner Zeh
In preparation of generating DMAR tables, provide the hook in SoC scope for the systemagent to write ACPI tables. The complete functionality is SoC-specific. Therefore the entry hook is defined as a weak function which can be overridden by SoC code. If the SoC does not have support for generating DMAR tables this hook will do no harm. Change-Id: I1333ae2b79f1a855e6f3bb39bf534da170ddc9e1 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/c/30989 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-01-28src: Don't use a #defines like Kconfig symbolsElyes HAOUAS
This is spotted using ./util/lint/kconfig_lint To work around the issue, rename the prefix from `CONFIG_` to `CONF_`. Change-Id: Ia31aed366bf768ab167ed5f8595bee8234aac46b Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/31049 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-01-28soc/intel/skylake: select FSP_M_XIP if MAINBOARD_USES_FSP2_0Matt DeVillier
Select FSP_M_XIP if MAINBOARD_USES_FSP2_0, since all SkyKabylake boards require FSP-M XIP when FSP 2.0 is used, and since not having it selected results in a non-booting image. Also, put select FSP_T_XIP if FSP_CAR in proper alphabetical order. Change-Id: I6d3986eda18297b12490cefb236f5de5faca6550 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/31110 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-01-28vboot: Makefile: Also apply CPPFLAGS include path fixups to ccoptsJulius Werner
In some cases (e.g. Arm architecture variants), include paths are stuck into <stage>-generic-ccopts rather than CPPFLAGS_<stage> (in fact, the whole redundancy between these two is kinda stupid and we should probably eliminate the latter, but I don't want to get into that right now). This patch makes sure those paths are also correctly translated when invoking $(MAKE) for vboot. Change-Id: I37f09b88e555567590664e0e6fac23c34fd887df Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/31084 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-01-28mb/asus/h61m-cs: Add ASUS H61M-CSdevmaster64
Working: - USB (Partially. Check "Not working") - PCIe - PCIe graphics - All SATA ports - Native memory init - On-board audio (back and front) - S3 (Sleep and wake) Not working: - Fan control - USB (If the keyboard has a USB Hub or if the keyboard is connected through 2 or more hubs then it doesn't initialize in time. A simple reboot allows the keyboard to be used in SeaBIOS and the bootloader) Untested: - PS/2 - On board graphics Change-Id: I4ed2077248a8d7123c728c790d9b81fe37956ed2 Signed-off-by: Abhinav Hardikar <realdevmaster64@gmail.com> Reviewed-on: https://review.coreboot.org/c/30767 Reviewed-by: Tristan Corrick <tristan@corrick.kiwi> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-28mb/google/octopus: Fix termination for unused dual voltage pinsShamile Khan
These pins should not have pull downs configured in standby state as that can cause contention on the termination circuitry and lead to incorrect behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination Configuration. BUG=b:79982669 TEST=Checked that code compiles with changes. Change-Id: If3cadc000ec6fc56019ee3f57e556dc819d5e0a5 Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/c/30823 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-01-28mainboard/google/octopus/variants/casta: Decrease touchpad I2C CLK frequencySeunghwan Kim
ELAN touchpad supports up to 400KHz, so we need to limit its CLK frequency to 400HKz. BUG=b:123376618 BRANCH=octopus TEST=built and verified touchpad I2C clk frequency gets be lower than 400KHz Change-Id: If7a43fe20c7e5abdf23c8c36e34c072c371563bf Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com> Reviewed-on: https://review.coreboot.org/c/31085 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-01-28mb/lenovo/thinkcentre_a58: Extend mb nameArthur Heymans
While branded as thinkcentre a58 this board can also be found as "L-IG41M". Change-Id: I06ed424138c46c6b2f29f15c7ea5c3648b26a8d3 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/31109 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-01-28mb/google/sarien: Using HID over I2C to enable Melf TouchScreenChris Zhou
Current Melfas touchscreen driver cannot unregister ifself when connecting without Melfas touchscreen or connecting with other devices. And Melfas touchscreen FW can use I2C and HID over I2C driver, so switch to using HID over I2C driver. BUG=b:122710830 BRANCH=master TEST=Verify touchscreen on sarien works with this change. Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com> Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186 Reviewed-on: https://review.coreboot.org/c/31062 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
2019-01-28amd/stoneyridge: Disable GPIO MASK STATUSRaul E Rangel
MASK_STATUS disables interrupt status generation for the entire GPIO controller when any debounce register is configured. This causes problems when the kernel is loading drivers because we could lose interrupts for previously loaded devices. sb_program_gpios is also not setup to wait when configuring PAD_DEBOUNCE, so there is a potential that we could lose the interrupt status enable bit for other registers. By disabling MASK_STATUS we avoid that problem. BUG=b:113880780 BRANCH=none TEST=Ran a reboot stress test that concluded that we are no longer losing TPM interrupts while booting. Change-Id: Ife1db3b1449f205092509595cbc3eca511bff57a Signed-off-by: Raul E Rangel <rrangel@chromium.org> Reviewed-on: https://review.coreboot.org/c/31082 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Daniel Kurtz <djkurtz@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-29 16:39:40 +0000