| Age | Commit message (Collapse) | Author |
|---|
|
Like Nyan, Veyron boards use a GPIO to reset the system so that we can
make the accompanying TPM reset secure and unforgeable. The normal
kernel reboot driver knows that, but the SoC-internal watchdog doesn't.
This patch implements a check for the global reset status register in
the early bootblock and triggers a hard_reset() when it matches "first
global watchdog reset" or "second global watchdog reset". Seems that
the difference between the two is is a choice controlled by
wdt_glb_srst_ctrl (unconfirmed), and we want this code to run in both
cases.
BRANCH=None
BUG=chrome-os-partner:33141
TEST=Run 'mem w 0xff800000 0x9' from the command line, watch how you end
up in recovery without this patch but can boot normally with it.
Change-Id: Ice79648831e1e97d22325711da9e82bbf6bf3c75
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 5d7cb52b2c2dcb2fff0bf83fc168439dade4b1b7
Original-Change-Id: I2581bde84f0445c15896060544e9acb60de91c8c
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/231734
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9629
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The only way to reliably reset an SD card in an unknown state is by
power-cycling. Since a kernel may crash and reboot at any point, SD
cards may be left in one of them fancy high-throughput modes that
depthcharge (or, in fact, a newly booting kernel without prior
knowledge) doesn't support, so we need to reset the card on every boot.
This patch adds support to turn off an RK808 regulator completely and
uses that to turn off SD card power rails in early romstage. The time
until configure_sdmmc() in ramstage turns them back on should be more
than enough to drain the power rail for an effective power-cycle.
BRANCH=None
BUG=chrome-os-partner:34289
TEST=Booted a Pinky from SD card, noticed that it works before and
after this patch.
Change-Id: Iaa5f7adaa59da69a964785c5e369ad73c6620224
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 95fba21907f1f3f686cb5a95b993736247db8f96
Original-Change-Id: I904b2d23ca35f765c000f9bee7637044f674eff9
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/233713
Original-Reviewed-by: Alexandru Stan <amstan@chromium.org>
Original-Tested-by: Alexandru Stan <amstan@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9626
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This function was added in upstream but was missing in Chromium OS
Change-Id: I35debf65153e5f280343eebfe91438ecf665ba22
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9677
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Freeing up memory on rk3288 is like squeezing water out of a stone right
now, but I still managed to get a few drops here and there. Let's hope
this will be enough.
BRANCH=None
BUG=None
TEST=Pinky builds and boots again. memsz is ~15K in bootblock and ~39K
in verstage.
Change-Id: Icf7ff3369bf367426a34f1490e0a041ae9bd6367
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9a3737ab535cdef228a1607433860f881db04412
Original-Change-Id: I90d9eab5b5d3af7a2e4b836a9c7b735b7c1c48e6
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/235870
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9609
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Since we can now reduce our vboot2 work buffer by 4K, we can use all
that hard-earned space for the CBMEM console instead (and 4K are
unfortunately barely enough for all the stuff we dump with vboot2).
Also add console_init() and exception_init() to the verstage for
CONFIG_RETURN_FROM_VERSTAGE, which was overlooked before (our model
requires those functions to be called again at the beginning of every
stage... even though some consoles like UARTs might not need it, others
like the CBMEM console do). In the !RETURN_FROM_VERSTAGE case, this is
expected to be done by the platform-specific verstage entry wrapper, and
already in place for the only implementation we have for now (tegra124).
(Technically, there is still a bug in the case where EARLY_CONSOLE is
set but BOOTBLOCK_CONSOLE isn't, since both verstage and romstage would
run init_console_ptr() as if they were there first, so the romstage
overwrites the verstage's output. I don't think it's worth fixing that
now, since EARLY_CONSOLE && !BOOTBLOCK_CONSOLE is a pretty pointless
use-case and I think we should probably just get rid of the
CONFIG_BOOTBLOCK_CONSOLE option eventually.)
BRANCH=None
BUG=None
TEST=Booted Pinky.
Change-Id: I87914df3c72f0262eb89f337454009377a985497
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 85486928abf364c5d5d1cf69f7668005ddac023c
Original-Change-Id: Id666cb7a194d32cfe688861ab17c5e908bc7760d
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/232614
Reviewed-on: http://review.coreboot.org/9607
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We have known for a while that the old x86 model of calling init_timer()
in ramstage doesn't make sense on other archs (and is questionable in
general), and finally removed it with CL:219719. However, now timer
initialization is completely buried in the platform code, and it's hard
to ensure it is done in time to set up timestamps. For three out of four
non-x86 SoC vendors we have brought up for now, the timers need some
kind of SoC-specific initialization.
This patch reintroduces init_timer() as a weak function that can be
overridden by platform code. The call in ramstage is restricted to x86
(and should probably eventually be removed from there as well), and
other archs should call them at the earliest reasonable point in their
bootblock. (Only changing arm for now since arm64 and mips bootblocks
are still in very early state and should sync up to features in arm once
their requirements are better understood.) This allows us to move
timestamp_init() into arch code, so that we can rely on timestamps
being available at a well-defined point and initialize our base value as
early as possible. (Platforms who know that their timers start at zero
can still safely call timestamp_init(0) again from platform code.)
BRANCH=None
BUG=None
TEST=Booted Pinky, Blaze and Storm, compiled Daisy and Pit.
Change-Id: I1b064ba3831c0c5b7965b1d88a6f4a590789c891
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ffaebcd3785c4ce998ac1536e9fdd46ce3f52bfa
Original-Change-Id: Iece1614b7442d4fa9ca981010e1c8497bdea308d
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/234062
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9606
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Non-x86 boards currently need to hardcode the position of their CBFS
master header in a Kconfig. This is very brittle because it is usually
put in between the bootblock and the first CBFS entry, without any
checks to guarantee that it won't overlap either of those. It is not fun
to debug random failures that move and disappear with tiny alignment
changes because someone decided to write "ORBC1112" over some part of
your data section (in a way that is not visible in the symbolized .elf
binaries, only in the final image). This patch seeks to prevent those
issues and reduce the need for manual configuration by making the image
layout a completely automated part of cbfstool.
Since automated placement of the CBFS header means we can no longer
hardcode its position into coreboot, this patch takes the existing x86
solution of placing a pointer to the header at the very end of the
CBFS-managed section of the ROM and generalizes it to all architectures.
This is now even possible with the read-only/read-write split in
ChromeOS, since coreboot knows how large that section is from the
CBFS_SIZE Kconfig (which is by default equal to ROM_SIZE, but can be
changed on systems that place other data next to coreboot/CBFS in ROM).
Also adds a feature to cbfstool that makes the -B (bootblock file name)
argument on image creation optional, since we have recently found valid
use cases for CBFS images that are not the first boot medium of the
device (instead opened by an earlier bootloader that can already
interpret CBFS) and therefore don't really need a bootblock.
BRANCH=None
BUG=None
TEST=Built and booted on Veyron_Pinky, Nyan_Blaze and Falco.
Change-Id: Ib715bb8db258e602991b34f994750a2d3e2d5adf
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e9879c0fbd57f105254c54bacb3e592acdcad35c
Original-Change-Id: Ifcc755326832755cfbccd6f0a12104cba28a20af
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/229975
Reviewed-on: http://review.coreboot.org/9620
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some boards spread their timer implementation out in multiple files with
one function each for no discernable reason. Let's clean that up to make
things a little simpler to find.
BRANCH=None
BUG=None
TEST=Booted Pinky, compiled Daisy and Pit.
Change-Id: I8b543d1a0d9af37bde5433b0c9271d687b2404b2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 887765e1bd88d7aa49ad9a5e98b8831c10da6c10
Original-Change-Id: I43d29cd1b4a1d89cfd40f6cba5ca99ada3b00f82
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/234061
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9601
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch doubles the ACLK peripheral clock for the PD_BUS power domain
to 297MHz, which is the closest to the maximum of 300MHz we can reach by
dividing GPLL. This frequency directly translates into SRAM speed, so
maximizing it has a huge impact on boot speed (especially with the lack
of SRAM caching).
BUG=chrome-os-partner:32987
TEST=Booted Veyron_Pinky. Hacked timestamps into vboot and confirmed
that the (visibly) long signature verification times are nearly halved.
Change-Id: Iafa3044854a4058a7f885c775119d964a6295de4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c230585f4344d0eab4f8eeaa761869965f2da08a
Original-Change-Id: I3f19eaa3d97dcc6235d820c71eb5edf2ae87d647
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/224524
Original-Trybot-Ready: Doug Anderson <dianders@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9600
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch uses the new bootblock_mainboard_early_init() hook to run the
UART pinmuxing on rk3288-based boards before initializing the console.
This allows us to get rid of the hacky second console_init() call in
bootblock_soc_init(). We can also simplify the pinmux selection a bit
since we know that a given board always uses the same UART (still keep
an assert around to be sure, though).
BRANCH=None
BUG=chrome-os-partner:32123
TEST=Booted on Pinky.
Change-Id: I3da8b0e4bd609f33cedd934ce51cb20b1190024b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: caabda8fc1ddb4805d86fd9a0d5d2f3cf738bfaf
Original-Change-Id: Ia56c0599a15f966d087ca39181bfe23abd262e72
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/231942
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9604
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch makes some slight changes to the way bootblock_cpu_init() and
bootblock_mainboard_init() are used on ARM. Experience has shown that
nearly every board needs either one or both of these hooks, so having
explicit Kconfigs for them has become unwieldy. Instead, this patch
implements them as a weak symbol that can be overridden by mainboard/SoC
code, as the more recent arm64_soc_init() is also doing.
Since the whole concept of a single "CPU" on ARM systems has kinda died
out, rename bootblock_cpu_init() to bootblock_soc_init(). (This had
already been done on Storm/ipq806x, which is now adjusted to directly
use the generic hook.) Also add a proper license header to
bootblock_common.h that was somehow missing.
Leaving non-ARM32 architectures out for now, since they are still using
the really old and weird x86 model of directly including a file. These
architectures should also eventually be aligned with the cleaner ARM32
model as they mature.
[pg: this was already partly upstreamed. These are the remains.
Further cleanup is necessary and on the short-term TODO, but beyond
the scope of this commit]
BRANCH=None
BUG=chrome-os-partner:32123
TEST=Booted on Pinky. Compiled for Storm and confirmed in the
disassembly that bootblock_soc_init() is still compiled in and called
right before the (now no-op) bootblock_mainboard_init().
Change-Id: Idf655894c4fec8fce7d3348d3b3e43b1613b35db
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 257aaee9e3aeeffe50ed54de7342dd2bc9baae76
Original-Change-Id: I57013b99c3af455cc3d7e78f344888d27ffb8d79
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/231940
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9602
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
After DDR PHY reset de-asserted, DLL automatically starts to
lock, and the lock time is maximum 5.12us. The output clock of
DLL supplies the clocks of DDR controller and PHY digital logic.
So before DLL lock, the clocks of DDR controller and PHY digital
logic are indeterminate. When programming DDR in the period of
DLL unlock, the programming maybe unstable because of the
indeterminate clocks. So we need wait for at least 5.12us after
de-asserting reset, then start to program DDR registers.
10us provide some safety margin.
BUG=chrome-os-partner:33148
TEST=I'm using the following command line test ok(15000 cycles).
"while sleep 4 && dut-control cold_reset:on sleep:.1 cold_reset:off;
do : ; done"
BRANCH=None
Change-Id: Ie7d615f5a2264c615c4b4413d6b828cd3d78cd2b
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 54e1a439c0e29aaf4fc542ae756f7bb036ceaf3e
Original-Change-Id: I55f8cb11ed3d7962567c5f40a31e6c8aed8fdcb0
Original-Signed-off-by: DaiLunXue <dlx@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/232894
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lunxue Dai <lunxue.dai@rock-chips.com>
Original-Tested-by: Lunxue Dai <lunxue.dai@rock-chips.com>
Reviewed-on: http://review.coreboot.org/9578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
edp must reset when device power up, otherwise the edp
register maybe uncertain, now the edp source clock default
select 27M, and in pinky and jerry board we use 24M as edp
sourec clock, if we want to reset edp, we must after the clock
source select 24M.
BUG=chrome-os-partner:34023
TEST=Booted Veyron jerry and read edid normal
BRANCH=None
Change-Id: I4b03dbabe5d3d595d2d56efb0cd82f510f8d2e1b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2292da77cc2322b85c4b4f4f20e4ebcc4c4d060d
Original-Change-Id: Ica031d2d52deb539c1a0a56968786d6952b3d0e8
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/231336
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: http://review.coreboot.org/9555
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Implement VOP and eDP drivers, vop and edp clock configuration,
framebuffer allocation and display configuration logic.
The eDP driver reads panel EDID to determine panel dimensions
and the pixel clock used by the VOP.
The pixel clock is generating using the NPLL.
BUG=chrome-os-partner:31897
TEST=Booted Veyron Pinky and display normal
BRANCH=None
Change-Id: I01b5c347a3433a108806aec61aa3a875cab8c129
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e4f863b0b57f2f5293ea8015db86cf7f8acc5853
Original-Change-Id: I61214f55e96bc1dcda9b0f700e5db11e49e5e533
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/219050
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9553
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
LDO7 (VCC10_LCD_PWREN_H) is essentially just a glorified GPIO that turns
the real VCC10 regulator on or off. We tried setting it to 3.3V since it
matches the VCC33_SYS voltage on the input of that regulator. However,
we didn't notice that the LDO only supports going up to 2.5V.
This patch changes the voltage to the allowed maximum, which should
still work fine as an enable line (and is the same value used by the
kernel). This removes an assertion error in the ramstage.
Also change the PMIC driver to assert maximum VSEL values based on the
LDO, because the lower-voltage ones support one more setting. (LDO3 is
actually listed to only go up to 0b1111 in the manual, and has a weird
jump from 0b1101 -> 2.2V (skipping over 0b1110) to 0b1111 -> 2.5V. I
don't know if that's a documentation error or what they were smoking
when they designed that, but we don't need to care for now.)
BRANCH=None
BUG=None
TEST=Booted on Pinky, no more ASSERTION FAILED.
Change-Id: I38bf99e38822fd0883fd4d0bd9a1b01143545a95
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 70f3149efbc3aa9a03ab3fd5be99d17d9c5e1c87
Original-Change-Id: I68a3bb882cf25d98aca8922ede2a17e1ef6524de
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/228292
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-by: Jerry Parson <jwp@chromium.org>
Reviewed-on: http://review.coreboot.org/9547
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This moves vboot1 and vboot2 files to their designated directory. Common
code stays in vendorcode/google/chromeos.
BUG=none
BRANCH=none
TEST=built cosmos, veyron_pinky, rush_ryu, nyan_blaze, samus, parrot,
lumpy, daisy_spring, and storm.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: Ia9fb41ba30930b79b222269acfade7ef44b23626
Original-Reviewed-on: https://chromium-review.googlesource.com/222874
Original-Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Commit-Queue: Daisuke Nojiri <dnojiri@chromium.org>
Original-Tested-by: Daisuke Nojiri <dnojiri@chromium.org>
(cherry picked from commit cbfef9ad40776d890e2149b9db788fe0b387d210)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia73696accfd93cc14ca83516fa77f87331faef51
Reviewed-on: http://review.coreboot.org/9433
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Our CBFS header offset on rk3288 was very low and overlapped with the
end of the bootblock on recent Pinky builds. This can create all kinds
of fun effects like BSS variables suddenly being initialized to
something else than zero, in an effect that jumps somewhere else for
every slightest code size change.
This patch moves the CBFS header offset up a bit and the CBFS ROM offset
down (because there's really no point in leaving such a large gap). This
resolves our immediate booting problems, and I'll also start on a patch
to add further checks somewhere that catch these overlaps in the future.
BRANCH=None
BUG=None
TEST=Created a Pinky image from the exact same commit version as the
official 6443.0.0 build, with a KERNELREVISION string of the exact same
length as the builder (which for some arcane reason is different than
running emerge locally, shifting the whole bootblock around with it).
Confirmed that I saw the same "Not enough room for another
sub-pagetable!" hang, and that this patch fixes it.
Change-Id: I9e59a282b3cd0af3b0d224d64c10b7c4d312ad02
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1a142cd2c51c6f51a1597c21ad513feb151e0938
Original-Change-Id: I8be5b7b7e87021cc1b3a91d336e8d233546ee188
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/228326
Original-Reviewed-by: Gediminas Ramanauskas <gedis@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9410
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Since the LAST_THSUT bit is uncertain value when it cold-reboot,
we remove the printout about this status bit in coreboot.
BUG=chrome-os-partner:33521
TEST=Boot on veyron_pinky rev2
Change-Id: I3b9791ffdffeff0721e3d86378db6255c5abc9ea
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 16464d3229ad1001952ef1b50fe3e606d1583462
Original-Change-Id: I258750797e32c28f86e73a01eede005e890a6906
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/228391
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9409
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
slowly raise to max cpu voltage to prevent overshoot,
and in our experience,when cpu run in 1.8GHz,the
vdd_cpu must up to 1.4V
BUG=chrome-os-partner:32716, chrome-os-partner:31896
TEST=Boot on veyron_pinky rev2,check the rk808 buck1 voltage 1400mv
and measure the overshoot is 1440mv
Change-Id: I759840bd8cf57a5589bf1862d04803f80f804164
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 567f616ff091883ed3275b407859c9399db981b2
Original-Change-Id: I9bb739b49ae4b4f7a60133fa38b0fe51b95c0d78
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/226753
Original-Reviewed-by: Doug Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9408
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We've had gpiolib.h which defines a few common GPIO access functions for
a while, but it wasn't really complete. This patch adds the missing
gpio_output() function, and also renames the unwieldy
gpio_get_in_value() and gpio_set_out_value() to the much easier to
handle gpio_get() and gpio_set(). The header is renamed to the simpler
gpio.h while we're at it (there was never really anything "lib" about
it, and it was presumably just chosen due to the IPQ806x include/
conflict problem that is now resolved).
It also moves the definition of gpio_t into SoC-specific code, so that
different implementations are free to encode their platform-specific
GPIO parameters in those 4 bytes in the most convenient way (such as the
rk3288 with a bitfield struct). Every SoC intending to use this common
API should supply a <soc/gpio.h> that typedefs gpio_t to a type at most
4 bytes in length. Files accessing the API only need to include <gpio.h>
which may pull in additional things (like a gpio_t creation macro) from
<soc/gpio.h> on its own.
For now the API is still only used on non-x86 SoCs. Whether it makes
sense to expand it to x86 as well should be separately evaluated at a
later point (by someone who understands those systems better). Also,
Exynos retains its old, incompatible GPIO API even though it would be a
prime candidate, because it's currently just not worth the effort.
BUG=None
TEST=Compiled on Daisy, Peach_Pit, Nyan_Blaze, Rush_Ryu, Storm and
Veyron_Pinky.
Change-Id: Ieee77373c2bd13d07ece26fa7f8b08be324842fe
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9e04902ada56b929e3829f2c3b4aeb618682096e
Original-Change-Id: I6c1e7d1e154d9b02288aabedb397e21e1aadfa15
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/220975
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9400
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ice7e27230010ffc48948f952394e849533f94085
Signed-off-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-on: http://review.coreboot.org/8989
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Add GENERIC_UDELAY Kconfig option so that a generic
udelay() implementation is provided utilizing the
monotonic timer. That way each board/chipset doesn't
need to duplicate the same udelay(). Additionally,
assume that GENERIC_UDELAY implies init_timer()
is not required.
BUG=None
BRANCH=None
TEST=Built nyan, ryu, and rambi. May need help testing.
Change-Id: I7f511a2324b5aa5d1b2959f4519be85a6a7360e8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1a85fbcad778933d13eaef545135abe7e4de46ed
Original-Change-Id: Idd26de19eefc91ee3b0ceddfb1bc2152e19fd8ab
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/219719
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9334
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
While upstreaming, some old (or downstream) names sneaked in.
Change-Id: I148fd8f46bc88c38ce1f62efe5771555bd5dcc5c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9350
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch is the start of a series to change all non-x86 SoC-specific
headers to be included as <soc/header.h> instead of the old
<soc/vendor/chip/header.h> or "header.h". It will add an include/soc/
directory under every src/soc/vendor/chip/ and append the .../include/
part of that to the global include path.
This matches the usage of <arch/header.h> for architecture-specific
headers and had already been done for some headers on Tegra. It has the
advantage that a source file which does not know the specific SoC used
(e.g. Tegra files common for multiple chips, or a global include file)
can still include SoC-specific headers and access macros/types defined
there. It also makes the includes for mainboard files more readable, and
reduces the chance to pull in a wrong header when copying mainboard
sources to use a different-related SoC (e.g. using a Tegra124 mainboard
as template for a Tegra132 one).
For easier maintainability, every SoC family is modified individually.
This patch starts out by changing Rk3288. Also alphabetized headers in
affected files since we touch them anyway.
BUG=None
TEST=Whole series: compared binary images for Daisy, Nyan_Blaze,
Rush_Ryu, Storm, Urara and Veyron_Pinky. Confirmed that they are
byte-for-byte identical except for timestamps, hashes, and __LINE__
macro replacements. Compile-tested individual patches.
Change-Id: I4d74a0c56be278e591a9cf43f93e9900e41f4319
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4ad8b6d2e0280428aa9742f0f7b723c00857334a
Original-Change-Id: I415b8dbe735e572d4ae2cb1df62d66bcce386fff
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/222025
Reviewed-on: http://review.coreboot.org/9349
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
check the cpu and gpu temperature in romstage,
if over 120 degrees celsius,shut down the device.
BUG=None
Test=Boot on veyron_pinky rev2, write value
3421(125 celsius) to grf_tsadc_testbitl register,
the device will be shut down
Change-Id: I275d643ce8560444a9b42ee566d5fd63ebcda35e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e0c597489dc0637ffa66ee9db0c4f60757f8889f
Original-Change-Id: If406d6a4f6201150f52ea7fc64cd50b45778d7aa
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/223259
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9348
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Solving the DACR bug will mean that XN bits suddenly become enforced on
non-LPAE systems, and we will no longer be able to execute out of a
region mapped DCACHE_OFF. When we enable the MMU in romstage we are
still executing out of SRAM, so we would instantly kill ourselves.
Solve this issue by enabling the MMU earlier (in the bootblock) and
mapping the SRAM regions as DCACHE_WRITETHROUGH. They should really be
DCACHE_WRITEBACK, but it looks like there might be hardware limitations
in the Cortex-A12 cache architecture that prevent us from doing so.
Write-through mappings are equivalent to normal non-cacheable on the A12
anyway, and by using this attribute we don't need to introduce a new
DCACHE_OFF_BUT_WITHOUT_XN_BIT type in our API. (Also, using normal
non-cacheable might still have a slight speed advantage over strongly
ordered since it should fetch whole cache lines at once if the processor
finds enough accesses it can combine.)
CQ-DEPEND=CL:223783
BUG=chrome-os-partner:32118
TEST=None (depends on follow-up CL)
Change-Id: I1e5127421f82177ca11af892b1539538b379625e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e7b079f4b6a69449f3c7cc18ef0e1704f2006847
Original-Change-Id: I53e827d95acc2db909f1251de78d65e295eceaa7
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/223782
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9342
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch does some general cleanup in the Rockchip clock code, and
adds some more assertions regarding the PLL VCO and output frequency
ranges. It changes all PLL divisors to use the lowest values that can
still hit the target frequency, since higher NR values lead to higher
jitter and higher NO values increase power draw.
Also change DDR3 frequency code to hardcode the optimal divisors for
certail frequencies. As a little hack we will interpret 666000000 to
actually mean 666666666.6P (and analogous for 533MHz), since that's what
you usually want for memory.
BUG=chrome-os-partner:32139
TEST=Boot on veyron_pinky rev2, check that dpll_is shown as 666666666 in
/sys/kernel/debug/clk/clk_summary.
Change-Id: I57d7ef34500984184e010c0cc7d73789338834d4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7466ffc035b3f06ac280f412bc496059abf3239c
Original-Change-Id: I4f3c39641955a95c6dfbe9334035eb670b138bf0
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/221801
Reviewed-on: http://review.coreboot.org/9339
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change re-writes the spi_xfer() function to support full-duplex
transfers.
Even though the code looks much different, the same basic algorithm
for setting up the transfer is used. The main difference is that
reads from rxdr and writes to txdr occur simultaneously and accounting
is more complicated, so I separated the higher-level accounting
portion from the low-level FIFO handling portion to simplify things.
BUG=chrome-os-partner:31850
BRANCH=none
TEST=Loaded content from SPI ROM fine, needs testing w/ EC
Change-Id: Ic109a02daf52ba694b63a73fec1a72b3c5c0fd71
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 6a14f5ff8ed04d62e8de6ad2f468b763ffb8213c
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I33d2f5179360baf94627c86b57d12f032897caf5
Original-Reviewed-on: https://chromium-review.googlesource.com/218881
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9338
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch creates a new mechanism to define the static memory layout
(primarily in SRAM) for a given board, superseding the brittle mass of
Kconfigs that we were using before. The core part is a memlayout.ld file
in the mainboard directory (although boards are expected to just include
the SoC default in most cases), which is the primary linker script for
all stages (though not rmodules for now). It uses preprocessor macros
from <memlayout.h> to form a different valid linker script for all
stages while looking like a declarative, boilerplate-free map of memory
addresses to the programmer. Linker asserts will automatically guarantee
that the defined regions cannot overlap. Stages are defined with a
maximum size that will be enforced by the linker. The file serves to
both define and document the memory layout, so that the documentation
cannot go missing or out of date.
The mechanism is implemented for all boards in the ARM, ARM64 and MIPS
architectures, and should be extended onto all systems using SRAM in the
future. The CAR/XIP environment on x86 has very different requirements
and the layout is generally not as static, so it will stay like it is
and be unaffected by this patch (save for aligning some symbol names for
consistency and sharing the new common ramstage linker script include).
BUG=None
TEST=Booted normally and in recovery mode, checked suspend/resume and
the CBMEM console on Falco, Blaze (both normal and vboot2), Pinky and
Pit. Compiled Ryu, Storm and Urara, manually compared the disassemblies
with ToT and looked for red flags.
Change-Id: Ifd2276417f2036cbe9c056f17e42f051bcd20e81
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f1e2028e7ebceeb2d71ff366150a37564595e614
Original-Change-Id: I005506add4e8fcdb74db6d5e6cb2d4cb1bd3cda5
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/213370
Reviewed-on: http://review.coreboot.org/9283
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This patch adds the macros __ROMSTAGE__ and __RAMSTAGE__ which get
predefined in their respective stages by make, so that we have one
specific macro for every stage. It also renames __BOOT_BLOCK__ and
__VER_STAGE__ to __BOOTBLOCK__ and __VERSTAGE__ for consistency.
This change is intended to provide finer control and clearer
communication of intent after we added a new (optional) stage that falls
under __PRE_RAM__, and will hopefully provide some robustness for the
future (we don't want to end up always checking for romstage with #if
defined(__PRE_RAM__) && !defined(__BOOT_BLOCK__) &&
!defined(__VER_STAGE__) && !defined(__YET_ANOTHER_PRERAM_STAGE__)). The
__PRE_RAM__ macro stays as it is since many features do in fact need to
differentiate on whether RAM is available. (Some also depend on whether
RAM is available at the end of a stage, in which case #if
!defined(__PRE_RAM__) || defined(__ROMSTAGE__) should now be
authoritative.)
It's unfeasable to change all existing occurences of __PRE_RAM__ that
would be better described with __ROMSTAGE__, so this patch only
demonstratively changes a few obvious ones in core code.
BUG=None
TEST=None (tested together with dependent patch).
Change-Id: I6a06d0f42c27a2feeb778a4acd35dd14bb53f744
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a4ad042746c1d3a7a3bfda422d26e0d3b9f9ae42
Original-Change-Id: I6a1f25f7077328a8b5201a79b18fc4c2e22d0b06
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/219172
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9304
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
before the rkclk_init(), we must set rk808
buck1 voltage up to 1300mv
BUG=chrome-os-partner:32716, chrome-os-partner:31896
TEST=Boot on veyron_pinky rev2,check the rk808 buck1 voltage 1300mv
and check the cpu frequency up to 1.8GHz
Original-Change-Id: I6a8c6e35bd7cc6017f2def72876a9170977f206e
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/222957
Original-Reviewed-by: Doug Anderson <dianders@chromium.org>
(cherry picked from commit 2e7e7c265691250d4a1b3ff94fe70b0a05f23e16)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Iff89d959456dd4d36f4293435caf7b4f7bdaf6fd
Reviewed-on: http://review.coreboot.org/9260
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
change i2c clock low period and high period proportion to 7:3
guarantee the low period more than 1.3us
BUG=None
TEST=Boot on veyron_pinky rev2,check the i2c clock frequency
Original-Change-Id: I235e9e3ff54ab3b9cabad36bab58a8409f7005a0
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/223002
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 57a5d90d394086483e0dcdd6279678658d07d842)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I6b0c9dfa540354f6463ed90c9f3f9503a4d5749e
Reviewed-on: http://review.coreboot.org/9259
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use the previously added frequency constants in patch
titled 'stddef: Add KHz, MHz and GHz constants'.
BUG=None
TEST=Compiled Veyron_Pinky.
Original-Change-Id: I4a1927fd423eb96d3f76f7e44b451192038b02e0
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/221800
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 41bb8026818b4381d4a6d43d2d433c207c3971bc)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I37a610d57f1a3d44796bf80de5104c2b5b3f3dac
Reviewed-on: http://review.coreboot.org/9254
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
rockchip_spi_slave has a fifo_size member which doesn't change.
This just replaces the struct member with a #define.
BUG=none
BRANCH=none
TEST=built and booted on Pinky
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I9ea5cdad49ee10c5f32304d0909c4a7e74a261f9
Original-Reviewed-on: https://chromium-review.googlesource.com/220471
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit f76cce3b38ac37f4df8abf6eebb8f7c7b29da095)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I3ab4eecfcce98aff3f6c9bd8f6c4e589784c60be
Reviewed-on: http://review.coreboot.org/9246
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This re-factors rockchip_spi to remove speed_hz which will instead be
passed in via rockchip_spi_init(), thus making it easier to support
other boards which may have different slave devices attached.
BUG=none
BRANCH=none
TEST=built and booted on Pinky
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I7baf0fa0a2660e3c975847fdec3eb92bcd0d6c10
Original-Reviewed-on: https://chromium-review.googlesource.com/220411
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit de33d2ed6352fc4c8e81dc53451f164a8792daf2)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ie6473e47d50b7e633688185e8d8036980b833f1c
Reviewed-on: http://review.coreboot.org/9245
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This patch moves init for I2C, SPI, ChromeOS GPIOs to the
board-specific bootblock init function on Pinky, the idea being
to isolate SoC code so that it's more readily adaptable for
different boards.
BUG=none
BRANCH=none
TEST=built and booted on Pinky
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I75516bbd332915c1f61249844e18415b4e23c520
Original-Reviewed-on: https://chromium-review.googlesource.com/220410
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 0a7dec2fe70679c3457b0bfc7138b4a90b6217c8)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ib2c2e00b11c294a8d5bdd07a2cd59503179f0a84
Reviewed-on: http://review.coreboot.org/9243
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Since the UART which is used for the serial console may change from
board-to-board, this moves CONSOLE_SERIAL_UART_ADDRESS from rk3288's
Kconfig into Pinky's Kconfig.
BUG=none
BRANCH=none
TEST=built and booted on pinky
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I29837a72d8cf205a144494a6c8ce350465118b34
Original-Reviewed-on: https://chromium-review.googlesource.com/221438
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 53bff629f2e9865656beabd81e6ce1eab7c728a9)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I65835c07a49dc3a3518c6bb24a29bc6ae7dd46c9
Reviewed-on: http://review.coreboot.org/9242
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
I'm not sure how the build didn't fail before. In either
case remove the duplication.
Change-Id: I764774f2b8a5839512af3f054b844a1a86efdb45
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9244
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
Add ddr3-samsung-2GB config and modify 533mhz linit.
Support ddr3 freq up to 800mhz.
Enable ODT at LPDDR3.
BUG=None
TEST=Boot Veyron Pinky
Original-Change-Id: Ic02a381985796a00644c5c681b96f10ad1558936
Original-Signed-off-by: jinkun.hong <jinkun.hong@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/220113
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Change-Id: I867753bc5d1eb301eb4975f5a945bfdba9b8f37d
(cherry picked from commit e6689cbb0ec50317672c8ebe4e23555ca2f01005)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9239
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
BUG=None
TEST=Boot Veyron Pinky and test the VDD_LOG
Original-Change-Id: Ie2eef918e04ba0e13879e915b0b0bef44aef550e
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/219753
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Change-Id: I444b47564d90b3480b351fdd8460e5b94e71927c
(cherry picked from commit 4491d9c4037161fd8c4cc40856167bf73182fda6)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9240
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
BUG=None
TEST=Boot Veyron Pinky and measure i2c clock frequency
Original-Change-Id: I04d9fa75a05280885f083a828f78cf55811ca97d
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/219660
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Change-Id: Ie7ac3f2d0d76a4d3347bd469bf7af3295cc454fd
(cherry picked from commit 4b9b3c2f8b7c6cd189cb8f239508431ee08ebc52)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9241
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
This patch adds support for the board changes in rev2 (board_id = 0001).
It also moves the existing mainboard.c code around a bit to group it by
component.
BUG=chrome-os-partner:32139
TEST=Booted on rev1. Confirmed SD card still works. Confirmed power
button was still as broken as before.
Original-Change-Id: Ifc4876687db64ca50e41d009d911446129d57b1b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/220251
(cherry picked from commit 9428e0d1b784b27790b3b3dbbb18a769e51c6fd3)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I8d3479aa314f8c6f1591c1b69b0a3827234fc730
Reviewed-on: http://review.coreboot.org/9237
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
this change makes veyron pinky to select a rw romstage using vboot2.
BUG=None
TEST=Booted Veyron Pinky. Verified firmware selection in the log.
BRANCH=None
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
CQ-DEPEND=CL:219100
Original-Change-Id: Ia1cfdacde9f8b17b00e7772a02e0d266afedb82f
Original-Reviewed-on: https://chromium-review.googlesource.com/219103
Original-Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Tested-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Commit-Queue: Daisuke Nojiri <dnojiri@chromium.org>
(cherry picked from commit 69c1e4b9ee200645d38d28165389aa85ef9b36cd)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I7b4a2db8bcb95038dfb55bb7ceee66ac4a6c9475
Reviewed-on: http://review.coreboot.org/9234
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The static gpio_t initializers are stylish, but they are still a little
too annoying to write and read in day-to-day use. Let's wrap that in a
macro to make it a little easier to handle.
BUG=None
TEST=None
Change-Id: If41b2b3fd3c3f94797d314ba5f3ffcb2a250a005
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 102a5c0a800f43d688d11d1d7bbc51e360341517
Original-Change-Id: I385ae5182776c8cbb20bbf3c79b986628040f1cf
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/220250
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9052
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This updates timer.h to #include the header necessary for u32,
and to change the one instance of uint32_t to u32 to be uniform.
BUG=none
BRANCH=none
TEST=compiled
Change-Id: I4d67045206fd94985774b8d46a307bbb2e337f30
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4ff2629fdf3c69c203fa61ec894bb4895990cb5e
Original-Change-Id: Ie406fb1f518af5d1fd1e623630b2bcbbef35622c
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/220612
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9051
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Instead of using rela_time use the stopwatch API as the
semantics fit perfectly with the expiration usage.
BUG=None
BRANCH=None
TEST=None, but similar usage tested on tegra132.
Change-Id: I91ef59212a2dd1b48640b1aaaab6acacf4e9b3e6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b1dd8380f04641f4f73caa3441f349d9eca6be05
Original-Change-Id: Iff3293debc2f85553c9e9b765084e5c00720012c
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/219713
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/8895
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
this change syncs the i2c driver with the one in depthcharge.
BUG=None
TEST=Booted Veyron Pinky
BRANCH=None
Change-Id: Ic9c7006770bba50fd412e0bcefc52f879b7195ec
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Commit-Id: 95ca6c88061062c0de95a8dd3567a71a372771b0
Original-Change-Id: I0d0fdefa58c5b4cc5c991be40796a800ccf074a5
Original-Reviewed-on: https://chromium-review.googlesource.com/218873
Original-Commit-Queue: Daisuke Nojiri <dnojiri@chromium.org>
Original-Tested-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8872
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The Rk808 PMIC is a part that will probably be used by most Rk3288
boards, so it makes sense to keep it as common code in the the SoC
directory. This patch puts LDO control functions into rk3288/rk808.c, so
that the mainboard only has to call a simple interface to set up the
specific LDOs it requires.
BUG=chrome-os-partner:30167
TEST=Booted both this and the old version with a stubbed-out
i2c_writeb(), ensured that the final values are the same.
Change-Id: I7efa60f8a357ce6be7490e64d2e0e3f72ad16f1c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4df22cd78ee04fefc6f7fa0e5c3d903eb1794422
Original-Change-Id: Ic172f9c402e829995f049726d3cb6dbd637039d1
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/217598
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/8871
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Some files for the veyron project were checked in with execute
permissions where it doesn't make sense. Fix.
BUG=chrome-os-partner:30167
TEST=None
Change-Id: I2a96816d4fd0af3949b0adaf5208fd2862835b5b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d7a408ff273d848b60aaad4f8b27103318e56111
Original-Change-Id: Ia3788abf3755baf028518efb975701cf6cb37e46
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/217673
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/8868
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: I877b4bf741f45f6cfd032ad5018a60e8a1453622
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 640da5ad5597803c62d9374a1a48832003077723
Original-Change-Id: I805d93e94f73418099f47d235ca920a91b4b2bfb
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209469
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8867
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: I4c1864171e56a81e8eda95a15ca6a6bc1adc7a70
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 814af4b653432295cb6d7222af4a6e5a8d9dfbf6
Original-Change-Id: I1a986fbc8b3737bae655207dd89865dd39aecf87
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209467
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: http://review.coreboot.org/8866
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Supports DDR3 and LPDDR3.Supports dual channel.ddr max freq is 533mhz.
ddr timing config file in src\mainboard\google\veyron\sdram_inf
Remove dpll init in rk clk_init(), add rkclk_configure_ddr(unsigned int hz).
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: I429eb0b8c365c6285fb6cfef008b41776cc9c2d9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 52838c68fe6963285c974af5dc5837e819efc321
Original-Change-Id: I6ddfe30b8585002b45060fe998c9238cbb611c05
Original-Signed-off-by: jinkun.hong <jinkun.hong@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209465
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8865
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: I63b4a62f624d34f7028321cb4576cbdb9cd10817
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3606d7eb06d66e23f4ee7ecb6862d23bde3acfd2
Original-Change-Id: I3e0cff1c6de464a8a79e30e239cfb0960cbae253
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209460
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8864
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: I23af280764eb28d3f6b215ab32553fe42ee73272
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: abf5c14c8b32573107d2a1c73a752e740264db7e
Original-Change-Id: I46257cc71cc3cd1e867edf589ddf09f7990d6784
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209462
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8863
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: Ica7b2bf2cf649c2731933ce59a263692bb2c0282
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ba9c36daedc749748f45e68a84f8c34c636adb1c
Original-Change-Id: Ia0e4e39d4391674f25e630b40913eb99ff3f75c4
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209427
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8862
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: I74b30ecfe40c039855b835db0dfd0cd25adf960e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a30378a3152c930029a5b170cc6bf46180b5c7b8
Original-Change-Id: I5105e5277b8072c06bb41b39479373697ef81c67
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209468
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8860
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: Ia19f8084a945992d9f252eb080c6c5c9990ac7de
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 30d02610e8e1e018025c2c1c970fb5b33d67d51b
Original-Change-Id: I8f273f8850e4792ca976bb7c2ed39cbe501401f2
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209461
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8861
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: I858ac723d640dde8538aebb968fcff364fa7207c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8253a9dbad2afdf9eb9a8554fd355e6815887407
Original-Change-Id: Ib6ee7e3092429a3e47b102751ed6a88aeb9ee7d3
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209429
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8859
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Call rkclk_init() in bootblock stage.
apll = 816MHz, gpll = 594MHz, cpll = 384MHz, dpll = 300MHz
arm clk = 816MHz, DDR clk = 300MHz, mpclk = 204MHz, m0clk = 408MHz
l2ramclk = 408MHz, atclk = 204MHz, pclk_dbg = 204MHz
aclk = 148.5MHz, hclk = 148.5MHz, pclk = 74.25MHz
BUG=chrome-os-partner:29778
TEST=Build coreboot
Change-Id: Id5967712e25df5be3a90f5d9ebe8671034deff68
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d35d9fe7b5925291e9303e5eb21d20dbbdee99d9
Original-Change-Id: I97d953258039f6caa499cef4462be8f1a05ce2ab
Original-Signed-off-by: jinkun.hong <jinkun.hong@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/209428
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/8858
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I6c3c1e871de33b4d0e968b254bbcf125cee9fddb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8704
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Most things still needs to be filled in, but this will allow us to build boards which use this SOC.
BUG=chrome-os-partner:29778
TEST=emerge-veyron coreboot
Original-Change-Id: If643d620c5fb8951faaf1ccde400a8e9ed7db3bc
Original-Signed-off-by: jinkun.hong <jinkun.hong@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/205069
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 2f72473a8c2b3fe21d77b351338e6209035878fb)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I53fd0ced42f6ef191d7bf80d8b823bb880344239
Reviewed-on: http://review.coreboot.org/8653
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
