| Age | Commit message (Collapse) | Author |
|---|
|
After adjustment on Careena EVT
TP: 400.0 KHz
TS: 396.8 KHz
H1: 396.8 KHz
BUG=b:112663934,b:112664258
BRANCH=master
TEST=emerge-grunt coreboot
measure by scope
Change-Id: I9eeaf9290d95969a283f14618878e28faf0ea46f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28119
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix the following failure from FWTS:
FAILED [LOW] AMLAsmASL_MSG_SERIALIZED_REQUIRED: Test 1, Assembler remark in line
131
Line | AML source
--------------------------------------------------------------------------------
00128| }
00129| }
00130| })
00131| Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
| ^
| Remark 2120: Control Method should be made Serialized (due to creation of named objects within)
00132| {
00133| Name (RBUF, ResourceTemplate ()
00134| {
================================================================================
ADVICE: (for Remark #2120, ASL_MSG_SERIALIZED_REQUIRED): A named object is
created inside a non-serialized method - this method should be serialized. It is
possible that one thread enters the method and blocks and then a second thread
also executes the method, ending up in two attempts to create the object and
causing a failure.
BUG=b:112476331
TEST= Run FWTS.
Change-Id: I6f4f6e7e94b01f673afc97d9415481ee63e406e3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28122
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SPD details to match with Coffeelake U RVP board
BUG=none
BRANCH=none
TEST=Boot on coffelake U rvp board and check if memory training is
passing and board boots till payload.
Change-Id: I953354cf5c6045731262f4f4e9da230187c2d246
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Update GPIO table as per board schematics.
GPIO table for other variants will be added later.
Change-Id: Ieb55d160ae2d6bff940840b1fba9411979332d4d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Nami doesn't support wakeup from hibernation by CR50. This causes the
device to remain turned off after CR50 update.
This patch disables turning off EC on cr50 update. CR50 resets the
whole system. So, EC reset is not required.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
BUG=b:112604277
BRANCH=none
TEST=gsctool -a -u /media/removable/cr50.bin && reboot
Verify EC reboots. AP prints 'Waiting for CR50 reset to pick up update'
then reboots.
Change-Id: I06f5eb6100e8af6ffec45d4de2b40eff44f89709
Reviewed-on: https://review.coreboot.org/28113
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These files are being updated to match the prevailing style
of cmos.default files.
Change-Id: I47d31d6fec8c9eb856aed0c63824d9556b7705e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
change I2C irq to EDGE trigger
BUG=b:112616824
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: I86ec32bb3f2626e65d76c3259e3c4244a970e5de
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Used default console log level is 7 in src/console/Kconfig.
So let cmos.default use the same level as default.
Change-Id: Ia39ee457a8985142f6e7a674532995b11cb52198
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Side effect was observed that after override BayHub EMMC
driving strength to the max, EMMC CLK will be reduced to
51.x Mhz from 200 Mhz.
This will cause OS installation fail on Samsung EMMC sku.
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I848ab0cae474b15fbc4264c8ade63d5c6b4e489d
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This file contains two instances of "dptf_enable" = "1". This change
removes the 2nd instance (it doesn't have an explicit comment like the
1st instance).
The dptf devices still seem to be present even with this change, as
expected.
Change-Id: I890006644be9176ebaf555cc121c816e12f2b596
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The spec of the sx9310 says the I2C interface can handle standard
(100kb/s) and fast mode (400kb/s). The current setting is using fast
plus (1000kb/s) so this change is reducing the speed to fast mode.
I've been using the sensors with this change for a few weeks now, though
I also don't recall seeing an issue prior to this change.
Change-Id: I337fc02c52565d6ec4d7bac1b3564f65238962dc
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 1fdb76945a9d06bbff37dee9da69e13a86c933f4.
Camera power is now handled by ACPI rules - no need to force the GPIOs
on by default.
BUG=b:80106316,b:111141128
Change-Id: Ifefec320884989f106a4b09c956d3a3279a1491a
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28072
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ping-chung Chen <ping-chung.chen@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This defines new GPIO pin for controlling the display panel CABC
function. The default value is high (enabled).
BUG=b:112154569
Change-Id: I29083ab18e37f929a55b450b143463c67fe0abea
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28070
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This updates the DPTF sensor names to reflect the sensor locations on
the board.
BUG=b:75454415
TEST=verified new strings show up in
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/INT3400:00/*/description
Change-Id: Ibffe6cb361de212ca03e75deaa8c454546d267a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28069
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia38c6f8d978065090564d449cae11d54ddb96421
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch updates Power Limit (PL) for AML.
- PL1 as 5W TDP as POR
- PL2 as 18W TDP as POR
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board and check default PL1/PL2 TDP.
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_0_power
5000000 (5W TDP)
cat /sys/class/powercap/intel-rapl/intel-rapl\:0/constraint_1_power
18000000 (18W TDP)
Change-Id: Icb02a8a7c5fcd5e6aee45f14eba540a6b3ed3d67
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/27427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add TSR2 DART/DTRT package
BUG=b:110451144
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test image with dptf.dv
Change-Id: I3328e17328415f5ebdcf84263e5456e11e55f769
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change updates GPIO configuration for bobba boards with id >= 1
This follows the same model as fleex:
a. Dynamically update touchscreen power enable GPIO in devicetree.
b. Provide default and bid0 tables for GPIO configuration in ramstage.
c. Configure WLAN enable GPIO differently in bootblock based on
boardid.
BUG=b:112354568
TEST=Built firmware for bobba
Change-Id: Id4ee4a1815e16ddfe60ed268688a8aaf4fb75579
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/28071
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Coffeelake U has 32MB flash chip support. Adding fmd file and enabling
CFL U board's Kconfig to output 32MB rom file.
Change-Id: I21431b7ac813781b12b95f80c6f8960a78caf4bc
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Add support for new board coffeelake RVP.
This patch is a copy patch and copies entire coffeelake_rvp folder from
cannonlake_rvp.
Changes done on top of copy:
1. Change copyright year from 2017 to 2018
2. Rename Cannonlake to Coffelake whenever applicable
3. Update entries in Kconfig and Kconfig.name
4. Rename variant directories to match coffeelake boards
Change-Id: Id37bfeb0ae51fd630fec96273216dbb2900782c7
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27904
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I189c981f3334836ab24bbc74491e9b58a2d403a4
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/27921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The paths defined in southbridge/intel/common/firmware/Kconfig should work just
fine.
Change-Id: Iaa780d9b3080416c6b1a7f24d97ecb8214962405
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28012
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All broadwell board set HAVE_IFD_BIN to default n, overloading the option in
soc, therefore just use the defaults in sb/intel/common/firmware.
Change-Id: I250dbbc9d61ecedc1a1eb48751ad966732604349
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28011
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need set the default HAVE_IFD_BIN explicitly to n.
Change-Id: I4a5fe45e7f8f6dd018937861b0fb92a8da49904e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28008
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need to redefine option present in
southbridge/intel/common/firmware/Kconfig.
Change-Id: I9999440031b07006e2df11e00dfb9f3dbe04f832
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28007
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix to accomodate for boards with more than 16 cores.
Change-Id: I35b61d94491c21ef76717f761e566ca815880f27
Signed-off-by: Samuel Jimenez <aerojsam@gmail.com>
Reviewed-on: https://review.coreboot.org/27847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I2c5edadfd035c9af08af9ee326a5a2dc8b840faa
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3108193c0e0b644cecb74ae0c7a7b54e24a75b58
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I80dd65484fd52e9048635091fb20a123e959e999
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27869
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ic61a69e19e97520da0702dfe6cb7496563fc34f4
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This was blindly copied from logs created under vendor BIOS in non-descriptor
mode which apparently set LAND in BUC.
Change-Id: I94c917600421ee742ece7f6f71309da80261da28
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove icc_max overrides to allow SoC code to set proper
icc_max based on CPU SKU.
BUG=b:78122599
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage', flash to
nocturne, boot to kernel and verify device doesn't hang after
a few minutes.
Change-Id: I37c44e2428b802d754f2b12b8a57601d257e6582
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27996
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a function to overwrite PL2 setting based on CPU
sku. From doc #594883, PL2 is 18W for AML-Y.
BUG=b:110890675
BRANCH=None
TEST=emerge-nocturne coreboot chromeos-bootimage & test with AML-Y
and KBL-Y skus.
Change-Id: Idfdc0c2434fdef56a7c25df05e640837a5096973
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27997
Reviewed-by: Caveh Jalali <caveh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a function to overwrite PL2 setting based on CPU
sku. From doc #594883, PL2 is 18W for AML-Y.
BUG=b:110890675
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage & test with AML-Y
and KBL-Y skus.
Change-Id: I468befcd2c4ad6c2bb9ae91b323a43f87ff65a26
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27765
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow thermal table (b:112274477 comment#1) for first tunning.
BUG=b:112274477
TEST=Match the result from DPTF UI.
Change-Id: I63b2e50a4f6fc5453e6564e277600498ac0e6244
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enable the GEO SAR feature for Octopus. Program wifi_sar VPD key.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:112288077
TEST=Program VPD key, extract acpi table ssdt and valiate WGDS entry.
Change-Id: I40a6fd9e0ec8b440996bf3389322fd89bcca15a4
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
PERST signal is asserted/deasserted by ACPI routines during
suspend/resume. Configuring IOStandby for WLAN_PE_RST can result in
failure to resume from suspend state with wake-over-WLAN. This change
removes the IOStandby configuration for WLAN_PE_RST.
BUG=b:112371978
Change-Id: Ic7c0b2aa144233f8bbb4e5169d96347a1290abe1
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When CNVi is being used, external wake using GPIO_119 is not
required. This change configures GPIO_119 as PAD_NC if CNVi is taken
out of reset.
BUG=b:112371978
Change-Id: Ifee90f428ed43c4d7c612c170476aff43b4a33ce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change uses drivers/intel/wifi chip for CNVi device to ensure
that:
1. Correct device name shows up in ACPI node
2. It is possible to pass any parameters from devicetree to wifi
driver for SSDT generation.
BUG=b:112371978
Change-Id: Ia49820dd4f9cf2e0a9ef14931fbddd8a723208c0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change checks to see if CNVi module is out of reset:
1. If yes, then PCIe device for WiFi is disabled.
2. If no, then CNVi device is disabled.
BUG=b:112371978
Change-Id: I6e6cf2e646c897df017913056db87ac0cffa1a8e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
I2C2 is unused on all octopus variants. This change disables it in
devicetree.
BUG=b:112458032
Change-Id: I55abef864c06a448011f9570d3e6c0aa8bfdc5bc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28016
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates GPIO configuration for fleex boards with id >= 1
This follows the same model as phaser:
a. Dynamically update touchscreen power enable GPIO in devicetree.
b. Provide default and bid0 tables for GPIO configuration in ramstage.
c. Configure WLAN enable GPIO differently in bootblock based on
boardid.
d. Disable unused I2C devices in devicetree.
BUG=b:112458032
TEST=No errors observed on boot-up on fleex.
Change-Id: Ib4c449168b08e2393e2395d6b49469be5599c2ce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The file `data.vbt` matches the VBT in the latest version of the vendor
firmware (version 3603). Tested with Linux 4.9 and everything works as
expected.
Change-Id: I8e3b1d274ac0df63989d966f477013e780611fa1
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/28050
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib0839933f8b59f0c87cdda4e5374828bd6f1099f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Allow for shared dram configuration by introducing a new table
that collapses the common settings after removing the part
numbers. When employing this scheme the part number comes
from CBI.
BUG=b:112203105
TEST=Placed part number in cbi. Faked out memory sku id. And enabled
DRAM part num always in cbi. Everything checked out.
Change-Id: I5229695ce3eb686421b89ac55d8df4b9fcec705c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Options that were deemed unneceesary on other code reviews have
been removed from the layout files. In addition, the checksummed
range has been extended to cover sata_mode and gfx_uma_size.
Change-Id: Id9e904f447809231806a786e39ed638f21e1bc5a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
I ported ga-h61m-s2pv based on the two Gigabyte b75m boards.
Based on another mainboard's code review comments, this patch
improves the code quality of these three similar boards.
ga-h61m-s2pv is tested and confirmed to be working, but I cannot
say the same regarding the other two mainboards as I do not have them.
Change-Id: Ib7747cceb5ba56f791677204cdc4c54c129c70c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Rotor is dead, long live [PROJECT NAME REDACTED]!
Change-Id: Ia9308944257255e077a44c1df262c7f49c69890c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27964
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add 3 new Kconfig options:
DRAM_PART_NUM_IN_CBI
DRAM_PART_NUM_ALWAYS_IN_CBI
DRAM_PART_IN_CBI_BOARD_ID_MIN
These control whether to 1. attempt to use CBI at all 2. always use cbi
and 3. conditionally use cbi based on board id. The intent is that the
MIN variant would be used for the tranisition period then cut over to
ALWAYS after full transition. Since multiple OEMs have different
schedules these options are there to bridge the gap. yorp. bip, and
octopus build targets would never flip DRAM_PART_NUM_IN_CBI, but in case
someone does the MIN values are 255 to always take the old path.
BUG=b:112203105
TEST=Set correct part number on phaser during testing.
Change-Id: If9a0102806d78e89330b42aa6947d503a8a2deac
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ief6a04ccb63658b5fb03cd1d298bf00948cf7410
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Careena EVT SanDisk EMMC sku has high fail rate of 0x5B reboot failure.
It'll need to increase 1.8V EMMC CLK/CMD, Data driving strength for
this issue.
CLK[6:4]
CMD,DATA[3:1]
original register value: 0x6B
enhanced: 0x7F
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I3db38ff12c566c258895c6643008a0472ca528bb
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27816
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Micron material that was broken has long since been fixed that
required this option. glkrvp had these stale entries and were
subsequently copied to octopus. Remove the need for this option.
BUG=b:35581751
Change-Id: Id73584367c2ad0e4958b5ea0f04a28e5fc82d085
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27959
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Skylake SoC code now sets the icc_max based on the CPU SKU, so we
should not hard-code it in the device tree.
BUG=b:110890675
BRANCH=None
TEST=boots on atlas
Change-Id: I7eb3499b7bea9ab2c49e1f299e2dbb688c8d1c33
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
|
|
This configures the ACPI FADT perferred power management profile to
PM_MOBILE instead of PM_DESKTOP.
I'm not sure what impact this actually has. I just noticed the other
boards have it set.
BUG=b:110971913
TEST=Made sure SYSTEM_TYPE_LAPTOP shows up in coreboot.config
Change-Id: Iea1b8359b80d167e69745358f543f025713294ba
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The devicetree is not run through a C pre-processor, so remove it.
Change-Id: I161be45b2035f3a8724bf3217260e7571c429da8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27927
Reviewed-by: Naresh Solanki <naresh.solanki.2011@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If GPP_E22(CABC_EN) remained floating GPI(SoC default) at V3.3_DX_EDP on,
it may cause damage on the GPIO pad.
To prevent, we would set this pad to GPO on romstage before EDP power on.
Since we need to cover all systems in market, I put it into romstage
instead of early_gpio_table.
BUG=b:111860510
BRANCH=poppy
TEST=Verified CABC_EN is set to GPO high 5ms before EDP power on
Change-Id: I34e2fe86329a88eb05e0ea3c6beac6a64754b41e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds variant callback to get GPIO configuration table in
romstage and configures these GPIOs before memory training is
performed.
BUG=b:111860510
BRANCH=poppy
Change-Id: I1eb51356fb3f4c0f4ff29b22dbcde6dbece303ad
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change provides implementation of smbios_mainboard_sku() to add
proper "skuX" string to SMBIOS table 1.
BUG=b:112163362
TEST=Verified "dmidecode -t 1" reports skuX correctly.
Change-Id: I7e42d2c80d791ea7170d066d2eeaa0c6811eb9c9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add default PSPP AGESA setting for Kahlee/Grunt mainboards.
BUG=b:112020107
TEST= build test
Change-Id: I8a8605402379de88a04f3a16553c308513fa1531
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Now that an updated bootloader with important fixes is available at coreboot
repository, all stoneyridge boards should use it. Move the selection of
SOC_AMD_PSP_SELECTABLE_SMU_FW from mb/google/kahlee to soc/amd/stoneyridge.
BUG=b:111428800
TEST=Build and boot grunt.
Change-Id: Idf8e348efbc85569aa1163125f412c5242c46eb4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27844
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update power limit1 value from 8W to 10W. There is an error
in the energy calculation for current VR solution on GLK.
Experiments show that when power limit1 set to 10W, gained
performance improvement with SoC TDP reaches max (6W) power.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Ic320d442e7401e4be2e8e16d691db4c803f0fdc1
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds ACPI properties for WDT8752A device.
BUG=b:111402335, b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Id186d5b87343007ae7e631d5d27464ee27e5b27d
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the default value for Iccmax which is specified in vr_config.c.
The AcLoadline and DcLoadline keep the poppy value. Besides, the
USB 2.0 ports located on the mainboard are set to USB2_PORT_SHORT
and the others on the daughterboard are set to USB2_PORT_LONG.
Those setting need to be fine tuned later.
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: Icabfac04c94b3d480872c243d811509e274ef122
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The gpio setting is based on the proto board schematics
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: I20fc081d372b8686f6128a7e85276f9c6798b199
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add memory configuration based on the proto board schematics
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: I45efdc7893b5bcbca0de6e932e1452cc1a2ff028
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Rammus uses DA7219 Headset, Maxim MAX98927 Smart Amps and 4 channel dmic
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: If21a3870ee4b000a776d2f3e025fb43ef2fe48c7
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move the build board directory from poppy to rammus.
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: I3a9fc2bbfe7261661f0c5c073baff0ff1434d09f
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Kahlee based boards don't use SATA, so disable SATA on all boards to save
power.
BUG=b:112139043
TEST=Build and boot grunt, checked the absence of SATA PCI.
Change-Id: I6a12c03a5a95b1c8b40609a3fe656df92548b80b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since only a handful of boards have descriptor blobs in the tree, it makes no
sense to have `HAVE_IFD_BIN` enabled by default then disabled on each mainboard.
This patch flips the default value of said variable, rendering all current
overrides unnecessary. The few boards which have an IFD in the blobs repo use
`select HAVE_IFD_BIN` to enable adding the IFD by default.
Since `HAVE_ME_BIN` depends on `HAVE_IFD_BIN`, the former has been removed
alongside the latter, and has been added to the boards with a ME blob as
`select HAVE_ME_BIN`.
Both `HAVE_IFD_BIN` and `HAVE_ME_BIN` have been removed from autoport as well.
Change-Id: I330c4886f8bea4b1a8ecad6505a0e5cc381654d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Due to vendor's requirements LED 2 and LED 3 should be turned
off in late boot process. Add appropriate functions to read and
write GPIO status.
Change-Id: Ia286ef7d02cfcefacf0e8d358847406efe1496fb
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change GPIO setting to use IOMUX to refer to GPIO by
IOMUX register as in BKDG for Family 16h Models 30h-3fh
Processor Rev 3.06.
Change-Id: Icf4a60acabe65cd7f9985bb3af8bd577764d4196
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Tested with GRUB 2.02 as a payload, booting Debian GNU/Linux 9.5 with
kernel 4.9. This code is based on the output of autoport.
The file `data.vbt` matches the VBT in the latest version of the vendor
firmware (version 4601).
This board works well under coreboot. A list of what works and what
doesn't can be found in the documentation part of this commit. To
summarise: the only known issues are that S3 suspend/resume doesn't
work, and that there is no automatic fan control via the super I/O.
Change-Id: I2a0579f486d3a44de2dd927fa1e76b90c3b48f62
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/27798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
These boards require polling vs interrupts, so remove the IRQ definition to
prevent it being added to the SSDT device entry.
Test: Boot Linux on various auron and cyan variants, verify no error for
'TPM interrupt not working' present in kernel boot log.
Change-Id: Ia1139389f075934d41e823ce5190011c90c7cc88
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch applies correct AC/DC loadline settings for Atlas from
VRTT report.
BUG=b:111419622
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage and use DbC to check
the AC/DC loadline settgins.
Change-Id: I6e85b885a6d3a1db9a980d12f3cfc036a771422a
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27788
Reviewed-by: Caveh Jalali <caveh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch makes sure we deassert the USB hub reset pin so the hub will
work with the next board revision that drops the external pull-up.
(Actual USB support comes in a later patch.)
Change-Id: I1efdc3594cfa3229891d42d445a21c1739170b79
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27790
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the required callbacks to read all strapping IDs on
Cheza.
Change-Id: I6437bbd03bdd00dfeedcafebabeb00b13588d052
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Extracted from live running Thinkpad x1 carbon gen1 with vendor firmware.
Thanks to Igor Lee.
Change-Id: Id59517d9040c98e67a42fbce537f42f6b0c6db2d
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Igor Lee <getrun@gmail.com>
Reviewed-on: https://review.coreboot.org/27782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Tuning of fan speed for different temperature values. Earlier while
running few benchmarks, fan was always getting on and starting at
higher speed. With this change fan will start with lower speed and
slowly speed gets increased if temperature continue going high.
Thermal team provided these data after fine tuning of fan speed.
BUG=None.
TEST=Verified on Nami running with different benchmarks and observed
fan speed.
Change-Id: Ic3be9e44deef9570200c71807a2ee712d9f20876
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27683
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is a potential IMVP8 issue for KBL that affects Intersil VRs
Nami is using one of the affected parts. The fix is to use an updated
microcode and also send a mailbox box command from FSP.
BUG=b:112081534
BRANCH=None
TEST=Build and boot Nami
Verify that suspend/resume and consecutive reboots are working
Change-Id: I6ec18a4c3fae6a66cf8a95685d91a8ba51e2697c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/27780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adapted from chromium commits 831a372 and cc96c27
[Banon: board 2nd source DDR memory]
Add support for hynix/H9CCNNN8GTALAR-NUD and Nanya/NT6CL256T32CM-H1
Original-Change-Id: Ifd161ba5ade44e71c88655f760ca66668b5c5178
Original-Change-Id: I5cba13701ed8e037e21d34ed55162ee56291a842
Original-Signed-off-by: T.H. Lin <T.H_Lin@quantatw.com>
Original-Tested-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Original-Reviewed-by: Vincent Wang <vwang@chromium.org>
Original-Reviewed-by: YH Lin <yueherngl@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I2166d1025ede33148c7ab623ba59190a342c4736
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from chromium commits 2319742 and 3b59fb2
[Edgar: Add Micron MT52L256M32D1PF-107 SPD data]
[Edgar: Add Hynix H9CCNNN8GTALAR-NUD and Nanya NT6CL256T32CM-H1 SPD data]
Supported 2nd source Hynix, Micron, and Nanya memory.
TEST=Built and used mosys command by "mosys -k memory spd print all"
Original-Change-Id: Iec9160b74d2812620d2d28f841d503e2d63c8579
Original-Change-Id: I610f01a0198f835a2038511ff78bf0cfba7812a0
Original-Signed-off-by: Hank2_Lin <Hank2_Lin@pegatroncorp.com>
Original-Reviewed-by: Vincent Wang <vwang@chromium.org>
Original-Reviewed-by: YH Lin <yueherngl@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: If2379d6e58425616f49d77b0cdea1cd90f9a8bfa
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from chromium commit adcb858
[cyan: Configure WLAN_CLKREQ as GPIO and always assert low]
This is a workaround for issue b/35648315 as proposed by Intel to
ensure that WLAN_CLKREQ always stays low.
BUG=b:35648315
Original-Change-Id: I178b3e4fbf74cf08eadfa8bd31b80b018f330e77
Original-Signed-off-by: Furquan Shaikh <furquan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/1055652
Original-Reviewed-by: Rajat Jain <rajatja@chromium.org>
Original-Tested-by: Rajat Jain <rajatja@chromium.org>
Change-Id: Ie3458b3fbd1ecadf6b99b9804fb98440cf8d6938
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from chromium commit cf18ab6
[Strago: mask Audio IRQ on boot]
Do not start with audio interrupt unmasked; this causes interrupt storms
on newer kernels that no longer mask all interrupts when initializing
Cherryview pincontrol driver.
TEST=Boot various cyan boards with kernels 3.18 and 4.14;
verify everything works.
Original-Change-Id: Id621682d3b59fea3ac54fb0ab92c8df9c78a6d43
Original-Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/894688
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Icb55c885ea661c41168d3bd24109d2cdbb225546
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from chromium commit 3750e09
[Strago: mark GpioInt() resources as PullDefault]
coreboot considers GPIO resources first-class citizens and initializes
all pads according to their intended use, with necessary pull settings
applied. Therefore let's use PullDefault as pull qualifier in AML,
letting the kernel know that it should not attempt to alter pull settings
when using GPIOs.
TEST=Built and booted on celes, cyan, and egdar; built for other cyan devices.
Original-Change-Id: Iff58a324e73a7eeac9b38df05a095fcfe7acd31b
Original-Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/898259
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I0c69e77c58b8ceca71bc0c99e16d10c3e539f783
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27760
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adapted from chromium commit 126d352
[Strago: switch Touchpad and Touchscreen interrupts to be level-triggered]
The Elan and other touch controllers found in this device work much
more reliably if used with level-triggered interrupts rather than
edge-triggered.
TEST=Boot several cyan boards, verify that touchpad and touchscreen
work.
Original-Change-Id: I59d05d9dfa9c41e5472d756ef51f0817a503c889
Original-Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/894689
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia4f8cf83351dae0d78995ce0b0ed902d1e4ac3e8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from chromium commit ee7a150
[Strago: do not hardcode virtual interrupt numbers]
Instead of hardcoding virtual interrupt numbers that may change as
the kernel changes, use GpioInt() resources to describe keyboard,
touchpad, and touchscreen interrupt lines.
TEST=Build and boot several cyan variant boards, verify keyboard,
touchpad and touchscreen work with newer kernels (4.14+).
Original-Change-Id: I98d5726f5b8094d639fb40dfca128364f63bb30b
Original-Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/894687
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Iecfb45be433249d274532eb746588483fedb3f52
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since this works on Yorp and Bip, we should enable EC SW sync for all
known boards so that it doesn't get forgotten.
BUG=None
TEST=None
Change-Id: Ifee8e0b6620dc7554160a10a8e4663db25b6413d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27755
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With commits 9987534 [southbridge/intel: Remove leftover TPM ACPI code]
and 66ce18c [soc/intel: Remove legacy static TPM asl code] removing
TPM ASL code from the southbridge's LPCB device, the LPC TPM chip driver
(drivers/pc80/tpm) must be added to devicetree in order to ensure the
new acpigen code is used to replace it.
Test: boot various google/samsung boards, verify SSDT created with
LPBC.TPM device and TPM visible to and usable by SeaBIOS and Linux
Change-Id: Iedaa01f26fb357914549bb3dda24b0bd6ef67480
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27786
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a function to overwrite AC/DC loadlines for differnt
projects.
BUG=b:111761175
BRANCH=None
TEST=emerge-nami coreboot chromeos-bootimage and use DCI to dump
AC/DC loadline settings. Tested on Vayne and Akali.
Change-Id: Id0068c5334c257b9f4c32b6088becbfe8391a864
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add lpddr4 skus for new memory sources K4F6E3S4HM-MGCJ and MT53E512M32D2NP-046.
BUG=b:111964159
BRANCH=master
TEST=emerge-octopus coreboot chromeos-bootimage
Change-Id: Id39a332998b28262e5aa45822078f3c4087f163f
Signed-off-by: nickchen <nickchen@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27747
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Peichao Li <peichao.wang@bitland.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This never got enabled for fleex; we should enable this to make it
easier to have updated EC firmware.
With this commit, here's the relevant console messages:
sync_one_ec: devidx=0 select_rw=4
update_ec: Updating RW(active)...
Trying to locate 'ecrw' in CBFS
update_ec: image len = 137580
EFS: EC is verifying updated image...
send_packet: CrosEC result code 1
EFS: EC doesn't support EFS_VERIFY command
vboot_hash_image: No valid hash (status=0 size=0). Compute one...
print_hash: RW(active) hash: 35ba735cf97dd990f6f7f0895264382aa20beb4e7ba57270b0a7b24686e26afd
Trying to locate 'ecrw.hash' in CBFS
sync_one_ec: jumping to EC-RW
send_packet: CrosEC result code 12
EC returned from reboot after 27753us
BUG=b:112038021
TEST=Successful boot after EC update via sync
Change-Id: I2dc97c8e2b07f3bdef0d723789cc12c23b32c135
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for libgfxinit
Test: boot stumpy, verify all outputs operational prior for pre-OS display
Change-Id: Ia720814c2225502316de5c5e9639c67df65a2ed0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The careena board requires a different setting within VBIOS in order to
pass the eDP eye diagram test. Update all kahlee boards to use the new vBIOS.
CQ-DEPEND=CL:1153080
BUG=b:111673328
TEST=Verify, via SOME unspecified method, that the new vBIOS is built into
the Grunt/Careena ROM files.
Change-Id: I268cd3dbce6ba1f7bd781d768f470463846a4e10
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27643
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Per AMD, the Integrated Micro Controller is not a supported feature of the
Stoney Ridge APU. Systems are expected to implement an external EC for
desired features. Remove IMC files and functions from gardenia.
BUG=b:111780177
TEST=Build gardenia
Change-Id: I570b7f8e364b0c2937592590cc033d5a6c9fade0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27650
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ibb13627bcd2ad023f7686b5ae0bd7331e09cf5b4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ife344d1699a2eff7d93738221a0e87d0481f05d7
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: If4d6c80e95469341f0c978f302f04508f50280bd
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ie95d9c04375e0125bae9bc01ae5caef423faf33e
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/27679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The careena board needs different video settings to pass eye diagram test,
which does not affect negatively the grunt board. In preparation for new
VBIOS, AGESA environment needs eDP high vdiff enabled.
BUG=b:111673328
TEST=Add debug code to AGESA to display set eDP. Build AGESA. Build and
boot grunt. Add new code to grunt, build and boot, verify eDP changed.
Change-Id: I3e6b409699e8192eb39cc189628ff95b9f985e54
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- add Nanya NT6CL256T32CM-H1 to memory strapping table
BUG=b:111906760
BRANCH=none
TEST=none
Change-Id: I1432b9ab84f01a7fee1bc562aa40c714ddbf639e
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
