| Age | Commit message (Collapse) | Author |
|---|
|
This is needed for NVMe to work when PCIe device is connected to the
CPU side of RPL soc.
BUG=b:311450057,b:300690448, b:319058143
BRANCH=None
TEST=Tested on device and was able to boot to the OS
Change-Id: Ic8a1fdcedf2ec6c7bf1dd00e02ef7c13e9338aac
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This needs to be disabled for RPL otherwise we'll hit the assertion:
[EMERG] ASSERTION ERROR: file 'src/soc/intel/alderlake/fsp_params.c', line 1066
There is a comment in the referenced file/line in the assertion that
says that "C state demotion must be disabled for Raptorlake J0 and Q0
SKUs." So, disabling it.
BUG=b:311450057,b:300690448
BRANCH=None
TEST=Tested that we didn't hit this assertion on the device after this
change
Change-Id: Ib7b2484de2d84c980550fd951f1e30efab0ee197
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79855
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1.In contrast to the MediaTek Wi-Fi module, the Intel Wi-Fi module needs
to load a SAR table.
2.Describe the FW_CONFIG probe for the settings.
- WIFI_6 for MTK Wi-Fi module MT7921L
- WIFI_6E for Intel Wi-Fi module AX211NGW
BUG=b:315418153
TEST=emerge-nissa coreboot
Change-Id: I37e8adc3de02707b2df541cc5e6f88083554eeb4
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
driver
Since DRIVERS_I2C_SX9324_SUPPORT_LEGACY_LINUX_DRIVER value on dedede
cannot meet DRIVERS_I2C_SX9324 on nissa, need to update the tuning
value. Update proximity sensor fine tune value with quandiso EVT
machine.
BUG=b:314550601
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot and verify p-sensor
watch 'cat /sys/bus/iio/devices/iio:device*/*raw'
Change-Id: I5fc3bc5876594f2df79d628bd986113d37087c3d
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
The APU boards have an NCT5104D chip on the LPC bus that implements some
serial ports that have the legacy IO port interface to the host and
doesn't describe this in the ACPI tables, so select
HUDSON_FADT_LEGACY_DEVICES to have the corresponding FADT bit set. Since
this chip doesn't provide an 8042-compatible keyboard controller, don't
select HUDSON_FADT_8042.
TEST=Surprisingly, this doesn't seem to make a difference to the Linux
kernel; is creates all ttyS[0..3] devices with and without this patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8872b8c3d6e0610630ba17a0fccdcf8cebb1d3c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
HUDSON_LEGACY_FREE controlled both if the legacy devices and the 8042
flags are set in the IA-PC boot architecture filed of the FADT. Since
some systems have legacy devices on the LPC bus, but no 8042-compatible
keyboard controller, replace this option with the two new options
HUDSON_FADT_LEGACY_DEVICES and HUDSON_FADT_8042.
TEST=The FACP table doesn't change on APU2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id4ff85630c90fb2ae8c8826bbc9049a08668210d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Tell binaryPI to not disable the LPC decodes for the IO ports used by
the serial ports on the Super I/O chip during the AmdInitReset binaryPI
entry point. Checked the Stoneyridge binaryPI source code which is
closely enough related to be reasonable sure that this option only
controls which LPC decode bits get cleared and won't have any other side
effects.
TEST=Now the full console output from the APU2 board gets printed on the
serial console.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: I91ef4423bd7bf6c1d7a175336f0f89479f2cde02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79852
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3a317d031e71f86afc50b229d1b97197552f4fa9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Update the VBT version from 249 to 251.
It is the same VBT settings as the previous one, but update it
based on ADL-P MR5 FSP so it will work with MR5 GOP driver to fix
the error "no graphic HOB found".
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I64229da1cb438de826e54dfc97d47d145fb4f0c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79020
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PIXA touchpad for variants of craaskov.
BUG=b:289962540
TEST=build craaskov firmware and test with PIXA touchpad
Change-Id: Iccf19b275548f44aec00be8631590b8a7ad1aa23
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79872
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
Removes unnecessary HAVE_FSP_LOGO_SUPPORT config from google/rex
baseboard. Intel Meteor Lake SoC now selects this config
automatically for supported platforms.
BRANCH=firmware-rex-15709.B
TEST=Able to build and boot google/rex and intel/mtlrvp.
Change-Id: I89bdd54cb73b11f74db2927a5eb86ab826c60517
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79860
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to some without mipi camera SKUs can't entering S0i3.
BUG=b:317670018
TEST=suspend_stress_test -c 1
Change-Id: Ifa8649a603c59946b530abd315113b405ceaf35a
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This partially reverts commit f493857c9bc1 ("mb/google/brya/var/*: Set
dGPU/LAN/WLAN device type to generic"). Setting the WLAN device type to
generic broke ACPI SSDT table definition, so set it back to pci.
BUG=b:318576073
TEST=build/boot google/nissa (pujjo), verify WLAN ACPI SSDT tables
contain the appropriate device entry.
Change-Id: If5dad9deb040c8cb0c507e11726f0ba44ccb2909
Signed-off-by: David Ruth <druth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
TEST=check FW screen on dojo
Change-Id: Ie870899226588ac2a2e80f77e434455f4913d387
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
TEST=check FW screen on Steelix, Tentacruel and Starmie
Change-Id: I429218d59389a6ab86b522dd597c07fa5b8ea821
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79777
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The sequences of configure_display() are similar on MediaTek platforms.
The sequences usually involve following steps:
1. Setup mtcmos for display hardware block.
- mtcmos_display_power_on()
- mtcmos_protect_display_bus()
2. Configure backlight pins
3. Power on the panel
- It also powers on the bridge in MIPI DSI to eDP case.
4. General initialization for DDP(display data path)
5. Initialize eDP/MIPI DSI accordingly,
- For eDP path, it calls mtk_edp_init() to get edid from the panel
and initializes eDP driver.
- For MIPI DSI path, the edid is retrieved either from the bridge or
from CBFS (the serializable data), and then initializes DSI driver.
6. Set framebuffer bits per pixel
7. Setup DDP mode
8. Setup panel orientation
This patch extracts geralt/display.c to mediatek/common/display.c and
refactors `struct panel_description` to generalize the display init
sequences. configure_display() is also renamed to mtk_display_init().
TEST=check FW screen on geralt.
Change-Id: I403bba8a826de5f3fb2ea96a5403725ff194164f
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79776
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce new config MTL_CHROME_EC_SHARED_SPI, tailored for
Chrome ECs utilizing an external shared SPI flash.
BUG=b:289783489
TEST=emerge-rex coreboot chromeos-bootimage is successful
Cq-Depend: chrome-internal:6691498
Cq-Depend: chrome-internal:6741356
Change-Id: I462c34c5adaefa37c652de293152243c58bad7c5
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Chrome EC configuration options that are common among
various boards have been consolidated under the
"BOARD_EXT_EC_SPECIFIC_OPTIONS" config.
BUG=b:289783489
TEST=emerge-rex coreboot chromeos-bootimage is successful
Change-Id: I0b85cc48d5cefadb52edbb27bf6cf370b27c395f
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79211
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change-Id: Ia97dbda30f657f0b1568364d712eaea8d134b3b0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79791
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DQS mapping for DIMM idx 6 was discovered to be incorrect to what
was in the schematics. Correcting the mistake in this CL.
BUG=b:311450057,b:300690448
BRANCH=None
TEST=tested on device and it passed memory training
Change-Id: I21f50e2f5b4fae09725c1c7532636ed1cc1a9043
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79843
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Introduce the HAVE_CONFIGURABLE_APMC_SMI_PORT Kconfig option that when
not selected will result in a default implementation of
pm_acpi_smi_cmd_port to be included in the build that returns APM_CNT.
SoCs that provide their own pm_acpi_smi_cmd_port implementation, need to
select this Kconfig option.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaceb61b0f2a630d7afe2e0780b6a2a9806ea62f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
For brya variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard).
BUG=b:317746281
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I3ca2e2d12a86eaae9e37870a2541c0287e354690
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79764
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation for adding other similar boards under it as variants.
Tested that z220_cmt still builds.
Change-Id: I96dec173e0d97d8564bad14778333b8231684ef8
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79434
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To avoid code duplication and to also bring the mainboards using the
Picasso SoC more in line with Cezanne and newer, factor out the SoC-
specific code from the mainboard's dsdt.asl files to the SoC's soc.asl.
TEST=Timeless builds result in identical images for Bilby, Mandolin, and
Zork/Morphius
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id4ed3a3d3cb55c8b3b474c66a7c1700e24fe908e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
This patch introduces the 512KB SI_EC FMAP region for storing the EC
firmware, a necessary addition to support EC chips without internal
flash memory.
As a testing platform, the MTLRVP Chrome SKU is utilized in conjunction
with the Microchip EC1723, and the changes are verified.
Cq-Depend: chrome-internal:6691498
Cq-Depend: chrome-internal:6741356
BUG=b:289783489
TEST=build "emerge-rex coreboot chromeos-bootimage" is successful.
changes are verified.
EC Log:
23-11-06 17:46:49.564 --- UART initialized after reboot ---
23-11-06 17:46:49.564 [Image: RO, mtlrvpp_m1723_v3.5.142816-ec:6596a3,
os:f660f7,cmsis:42cf18,picolibc:6669e4]
23-11-06 17:46:54.609 D: Power state: S5 --> S5S4
23-11-06 17:46:54.620 D: Power state: S5S4 --> S4
23-11-06 17:46:54.620 D: Power state: S4 --> S4S3
23-11-06 17:46:54.642 I: power state 10 = S3S0, in 0x0087
23-11-06 17:46:54.642 ec:~>: Power state: S3S0 --> S0
Change-Id: I788dbeaad05e5d6904fb2c7c681a0bf653dc7d84
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79209
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot, preventing privacy LED blink.
BUG=b:317434358
TEST=none
Change-Id: I43044e64c2c3a645ec0cad2ac903cc19ac89c9af
Signed-off-by: Jason Chen <jason.z.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79803
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous and remove devices which are turned off.
Built all variants with BUILD_TIMELESS=1 and the resulting binaries
remain the same.
Change-Id: I7752819091e2a75c8d818f7d0cf90eabc11c4759
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Marvin Evers <marvin.evers@stud.hs-bochum.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous and remove devices which are turned off.
Built razer/blade_stealth_kbl with BUILD_TIMELESS=1 and the resulting
binary remains the same.
Change-Id: I0ffda6ee37e146e894a271c553e998a269c19294
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Marvin Evers <marvin.evers@stud.hs-bochum.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous and remove devices which are turned off.
Built all variants with BUILD_TIMELESS=1 and the resulting binaries
remain the same.
Change-Id: I1fd5f2a1c8adb5f379d7f3d0b54dca9c3ee6e2b3
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Marvin Evers <marvin.evers@stud.hs-bochum.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
1. Set PCIe related GPIOs to NC if fw_config use "WIFI_CNVI".
2. Set CNVi related GPIOs to NC if fw_config use "WIFI_PCIE".
3. Remove "ALC5650_NO_AMP_I2S" case in
fw_config_gpio_padbased_override(). bt_i2s_enable_pads should not
relevant to audio codec/amp, and it is already enabled in "WIFI_CNVI"
case.
BUG=b:312099281
TEST=Build and test on karis
Change-Id: Ib1a32f1a38ae33cf992b80a3408aa8e2fa3ddab0
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79765
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add touchscreen ILTK for craaskwell.
Refer to ILI2901A-A200 Data Sheet_V1.1_20231026.
BUG=b:308873706
TEST=build and check touchscreen function on craask
Change-Id: I6a68855b1659ff0c9cd33a0ec9acbd289f525a3d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79735
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
|
|
Create the dita variant of the taranza project by
copying the files to a new directory named for the variant.
BUG=b:317292413
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DITA
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I843e33f30cd356e4f12330bdfe2d53a0b3920ef3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79655
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
As a preparation for WiFi SAR table addition, adding hook for it.
BRANCH=nissa
BUG=b:315418153
TEST=emerge-nissa coreboot
Cq-Depend: chrome-internal:6790137
Change-Id: Idb200699bb8c8581b9512ec8ec9442f65f8822b3
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Align the comments on the PIRQ table entries for the PCI bridge devices
to the external PCIe ports with the devicetrees of the different APU
boards.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id25ae8422c7c5c79dc8666a28a8219c77af324da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If08f7674509c953cf46c4e0d280edc9f863ef2d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79675
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: I30cff76abddd3f9a81ac5041260ca7ab1d5244f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add GFX devices for DDI (eDP and HDMI) and TCP (USC C0 and C2
ports). Copied the PLD placements from USB PLDs.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: Ic39916819f64ede1c80eccfd05ba4916b9f285af
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Update definition to be more intuitive and extensible.
Port descriptors will be defined as individual entities and added
to the descriptor list as such.
BUG=b:281059446
TEST=builds
Change-Id: I23ddd11b7e4da35a0d81299aa648f928e81ea24e
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79626
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update definition to be more intuitive and extensible.
Port descriptors will be defined as individual entities and added
to the descriptor list as such.
BUG=b:281059446
TEST=builds
Change-Id: Ic5a06a7d1bdb9123a0a242a571f094ac3233d7b2
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79627
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This is a preparation to make the next patch result in identical images
for timeless builds and also aligns Zork's DSDT more with Guybrush's
DSDT.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I46835b404be13f150c68680afb3fcc78639e08f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Extracted from a system running OEM BIOS version F.42.
intelvbttool --inlegacy --outvbt data.vbt
Change-Id: I6e499eb7ff8edb6556f8211d2fb8246cba5f5276
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79625
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
update DTT settings for thermal control,the values before
Sensor1 and Sensor2 were set too high. Modify the protection
temperature to better meet DUT requirements.
BUG=b:291217859
BRANCH=none
TEST=emerge-rex coreboot
Change-Id: I8abc866c0d05a2437c34198e6b8fb4a58c1cb829
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79683
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
According to datasheet, EN_TCHSCR_PWR high --> SOC_TCHSCR_RST_R_L high
should over 5ms. And current measure result is 200us.
Set EN_TCHSCR_PWR to output high in bootblock to make it meet datasheet
requirment.
Measurement result of EN_TCHSCR_PWR high --> SOC_TCHSCR_RST_R_L high:
Power on --> 31.7 ms
Resume --> 38.7 ms
BUG=b:314245238
TEST=Measure the sequence
Change-Id: I56e455a980b465f27794b30df058ec0944befc2e
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79571
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add probe DB_C_A_LTE/DB_C_A for Type-C Port C1 (daughter board).
DB_A is only used for skus without Type-C Port C1.
BUG=b:316048649
TEST=emerge-nissa coreboot
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Ifb702c497740953144b43c56653da16fade1053f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79629
Reviewed-by: Kyle Lin <kylelinck@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Some GPIOs were not configured correctly according to the HW
spreadsheet provided by the HW team.
* GPP_B5/GPP_B6 use NF1, not NF2
* GPP_B23 should use NF2, no GPI
* GPP_D11 should be set to NC
* GPP_E21/22 should be using NF (previous NC)
* GPP_F17 is a GPO
* GPP_F18 should be an interrupt, not a NF
BUG=b:300690448,b:316180020
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I9e1e62adb79bd7fdab935afdbf2d23f9061b88aa
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes in this CL are to fix the pad's reset field
as needed. See "Intel SoCs" section in
https://doc.coreboot.org/getting_started/gpio.html for reset
definitions.
BUG=b:300690448,b:316180020
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I4285136184c648adb9dc97748bd6b01cba3f8ddd
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes in this CL include fixing the pulls for
GPIOs as necessary, making sure that it matches what is in the HW
team's spreadsheet.
BUG=b:300690448
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: Ie50cb3c6fc85f1633c1afd1330c0e040e04b0ec1
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79704
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes here include changing the pad config to NC
because it is not being used in ChromeOS.
BUG=b:300690448
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I15471e4d7ff25c858b05ef024f15ca7c0b9e598e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79703
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add HDMI GPIO configuration to early GPIO list to support
VGA text o/p in Pre-RAM stage on HDMI.
BUG=b:316982707
TEST=Erase MRC cache and reboot, SOL text display on HDMI/eDP
Change-Id: Idb2af56baeb4d0ef9db5fc1c5dbcebecee6515e6
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79572
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Since the camera sensor and camera eeprom share GPP_A12, remove
the off timing to avoid issue of camera sensor loss, but this
will increase system power by 5mW.
(Before root cause, this is a short term workaround to unblock
function test.)
BUG=b:298126852
TEST=1. Run coldreboot/warmreboot check see if the camera sensor lost.
2. Run S0ix check to see if the camera function abnormal.
Change-Id: I49b6ecbfbf3dddd6575bdaaf9c8fd0ee6c09af25
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79647
Reviewed-by: Jason Z Chen <jason.z.chen@intel.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
|
|
set slew rate to 1/8 for GT domain.
BUG=b:312405633
BRANCH=none
TEST=Able to build and boot google/screebo
Change-Id: Ib5cb07b7effc4a51c2119183010a03e026f639f8
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
|
|
Some of the boards use the EC_SYNC pin to wake the AP but do not
advertise the pin as wake capable in the CREC _CRS resource. Relevant
boards were determined through empirical testing and inspection of gpio
configuration.
Update the ACPI tables for rex, brya, and brox based boards to advertise
their EC_SYNC pin as wake capable.
BUG=b:243700486
TEST=-Dump ACPI and verify ExclusiveAndWake share type is set when
EC_SYNC_IRQ_WAKE_CAPABLE is defined
-Wake Aviko via keypress and verify chromeos-ec as wake source
-Wake Screebo via lid open and verify chromeos-ec as wake source
Change-Id: I5828be7c9420cab6ae838272c8301c302a3e078c
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79374
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
UART0 is routed to a USB-serial converter chip on the Onyx board, so
also enable this UART in the devicetree, so that the OS will be able to
use this UART.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7b2577d799fd82a0aa0c9b01324930237e204aa0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
FSP default value for LpDdrDqDqsReTraining is 1. For boards
that didn't set LpDdrDqDqsReTraining to any value, 0 was being
assigned and it caused black screen issue.
BUG=b:311450057
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I4a009076e50408a4f7ff16ddc96a0f2e47b09470
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79646
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
GPP_B02 and GPP_B03 were set incorrectly previously.
This CL corrects these settings according to schematics.
BUG=b:305793886
TEST=Built FW image correctly.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Id62f15f7a77ac43c72cc6b2645816d6c87133a0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Only EC will use field "PANEL_PWRSEQ_EC_CONTROL".
Add this field in coreboot for align fw_config settings.
BUG=b:314245238
TEST=emerge coreboot pass
Change-Id: Icecb44a338ddc28027e362332c6a69cc9fd268d5
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79570
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After confirm with thermal, only EC will reference FAN field in
fw_config.
Update the settings for align fw_config.
BUG=b:307822225
TEST=emerge coreboot pass
Change-Id: Id7c4cdba29c5500c06d0f2293495650bb14b9e9c
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79573
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
|
|
UART1 is selected for debug uart in Kconfig, it also needs to enabled
in devicetree. With this serial output doesn't stop during the device
enable step.
TEST:Build onyx_poc board
Change-Id: I7c910301c6eca5d3057785607139ac03b344bc15
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use same indent levels for switch/case in order to comply with the
linter.
Change-Id: I602cf024ec84b15b783d36014c725826f9d6595e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79418
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Acoustic noise mitigation for google/screebo and set slew rate
to 1/8 for IA domain and ignore the slew rate for SA domain.
BUG=b:312405633,
TEST=Able to build and boot google/screebo.
Before:
[SPEW ] AcousticNoiseMitigation : 0x0
[SPEW ] FastPkgCRampDisable for Index = 0 : 0x0
[SPEW ] SlowSlewRate for Index = 0 : 0x0
After:
[SPEW ] AcousticNoiseMitigation : 0x1
[SPEW ] FastPkgCRampDisable for Index = 0 : 0x1
[SPEW ] SlowSlewRate for Index = 0 : 0x2
Change-Id: Ib86939ab48c2c6e7d0491d7c1cb4a2c7c6a1b568
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79323
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
This updates all warnings currently being printed under the files_added
and build_complete targets to the show_notices target.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ia14d790dd377f2892f047059b6d24e5b5c5ea823
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79423
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
when S0ix returns S0, PERST needs to delay until
Main 3V3 is stable and then pull up
BUG=b:313976507
TEST=emerge-rex coreboot,measurement waveform verify pass
Change-Id: I33a86e52fab3c5c8cba6ebed0cbdd1b88b6538b0
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79320
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For EVT SCH:
1. Use GPP_D15 to control AVDD and AFVDD simultaneously for MIPI Camera.
2. Delay reset for 5ms when device power on.
BUG=b:312663347
TEST=1. Google Camera app working
2. Passed EA verified
Change-Id: I880fb309fcef006090e2849fa6c3a0d472851851
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
With 1ms delay, reset is de-asserted too soon, before power is fully
up, causing a glitch to the reset signal. The issue is resolved with
4ms delay.
TEST=tested on google/jinlon device and observed the issue is resolved.
BUG=b:260253945
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I4efe916824cc193a7c2db7599b37f0d4de40bfce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79474
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
BUG=b:312099281
TEST=Build and boot to Karis. Verify the config from serial logs.
w/o this CL -
```
[SPEW ] ------------------ CNVi Config ------------------
[SPEW ] CNVi Mode = 1
[SPEW ] Wi-Fi Core = 1
[SPEW ] BT Core = 1
[SPEW ] BT Audio Offload = 0
[SPEW ] BT Interface = 1
```
w/ this CL -
```
[SPEW ] ------------------ CNVi Config ------------------
[SPEW ] CNVi Mode = 1
[SPEW ] Wi-Fi Core = 1
[SPEW ] BT Core = 1
[SPEW ] BT Audio Offload = 1
[SPEW ] BT Interface = 1
```
Change-Id: Icd2c42261fdcfa5aac17be28fde3804348ddf9b4
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
1. Anraggar doesn't support SDCard, so disable SDCard contorller.
2. Not disabling it will cause can't enter S0ix on first suspend.
BUG=b:313585586
TEST=1. check lspci
2. can enter S0ix on first suspend
Change-Id: Ie4747d9c5d6ae93d29ef78b629855e0dd320c4db
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This file is identical to the copy currently found in the blobs
repository; it is simply being relocated for consistency and since it
does not need to be in an external repo.
BUG=none
TEST=build/boot skyrim
Change-Id: I352f58e0d3965356f3282a2653c6c11b44853857
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
This file is identical to the copy currently found in the blobs
repository; it is simply being relocated for consistency and since it
does not need to be in an external repo.
BUG=none
TEST=build/boot guybrush
Change-Id: Ice4cbaccca13e9c4ae246fdcde5c89aa2086f1e1
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
This file is identical to the copy currently found in the amd_blobs
repository; it is simply being relocated since it is mainboard specific
and does not need to be in an external repo.
BUG=none
TEST=build/boot morphius
Change-Id: Ia78fcd065fbf4d5ba6ec4edc3f8f937badf66ecc
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79591
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For initial debugging, we want to disable SW syncing. Will re-enable
in the future.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
run gbb_utility --get --flags <image>
make sure that it returns 0xa39
Change-Id: I865e9585ab37d1328a0ff54c6343cdad2c02220c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79569
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
|
|
Even though this mainboard is called 'Onyx', the openSIL implementation
and the corresponding coreboot integration is only a proof of concept
that isn't fully featured, has known limitations and bugs, and is not
meant for or ready to being productized. Adding the proof of concept
suffix to the name should point this out clearly enough so that no
potential customer could infer that this might be a fully functional
and supported implementation which it is not.
Change-Id: I157a8fffdc2a8543465fe8d444ac87f3f417389f
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77896
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Even though this SoC is called 'Genoa', the openSIL implementation and
the corresponding coreboot integration is only a proof of concept that
isn't fully featured, has known limitations and bugs, and is not meant
for or ready to being productized. Adding the proof of concept suffix to
the name should point this out clearly enough so that no potential
customer could infer that this might be a fully functional and supported
implementation which it is not.
Change-Id: Ia459b1e007dcfd8e8710c12e252b2f9a4ae19b72
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77894
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The default EPP is set at 50%, which is deemed insufficiently
aggressive for meeting the MTL performance expectations in
balance_performance mode.
# cat /sys/devices/system/cpu/cpu0/cpufreq/energy_performance_preference
balance_performance
# iotools rdmsr 0 0x774
0x0000000080003f06
EPP=45% is giving the required performance in MTL.
# iotools rdmsr 0 0x774
0x0000000073003d06
NOTE: Kernel changes are necessary to ensure that the EPP (Energy Performance Preference) configured in the BIOS is not overwritten: https://patchwork.kernel.org/patch/13461932
BUG=b:314275133
TEST=Build and boot.
Change-Id: I1953994cdb4e9363fdd4b4728e3e5236276c06c8
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79386
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Non-touchscreen sku will set related GPIOs to NC. If touchscreen enabled
in overridetree for non-touchscreen sku, the boot time will be 6-7s. Set
touchscreen probed to TOUCHSCREEN_UNKNOWN for reduce boot time from 6-7s
to under 1s.
BUG=b:316434359
BRANCH=firmware-nissa-15217.B
TEST=Boot time (cbmem -t) from 6,460,972 to 922,844
Change-Id: I016ce762f726b7624bd060284f74f0992cb129b6
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
FSP default value for LpDdrDqDqsReTraining is 1. For boards
that didn't set LpDdrDqDqsReTraining to any value, 0 was being
assigned and it caused black screen issue.
BUG=b:302465393
TEST=Boot to OS with debug FSP, check LpDdrDqDqsReTraining = 1
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I301a6e43f2944ffbc63431393378ab8b23450032
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
The original DA7219 is designed to use a 500ohm mic detection
threshold. Some headset mics (e.g. Logitech H111) have a lower DC impedance that is lower than the threshold and thus cannot be
detected. Lower the threshold to 200ohm to match the new default
value provided by Renasas as in https://patchwork.kernel.org/project/alsa-devel/patch/20231201042933.26392-1-David.Rau.opensource@dm.renesas.com/ to support such headsets.
BUG=b:314062160,b:308207450
Change-Id: I6415e84a4622e0c61bc74b94536fe734048a043f
Signed-off-by: Terry Cheong <htcheong@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
FSP default value for LpDdrDqDqsReTraining is 1. For boards
that didn't set LpDdrDqDqsReTraining to any value, 0 was being
assigned and it caused black screen issue.
BUG=b:302465393,b:315739133
TEST=Boot to OS with debug FSP, check LpDdrDqDqsReTraining = 1
Change-Id: I5d61301fddac6630bb1c48e992dd76e5cf02a272
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79533
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iab640551d6dd246884802ced948ff8c359d922a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79470
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change GPP_B14 from UP_20K to NONE for compatible
with DVT1 and DVT2 board
BUG=b:272447747
TEST=enable usb OC2 function to ensure USBA work normal
Change-Id: Ib7720980335660f423b3a74199ceedc113ec70df
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79431
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DTT settings based on the suggestion of the thermal.
BUG=b:313833488
TEST=emerge-nissa coreboot
Change-Id: I2296990062cadc05202e3d1ab90af04234bda885
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
1. Ref to SCH, LTE use USB3 Port3, enable it.
2. Explicitly define the use of USB3 Port1 & USB3 Port2.
BUG=b:315061146
TEST=can pass PCIe Hardware Compliance Test
Change-Id: I03d6925020012fa740bbd0168a2f5b02ea6763b4
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change code style to be compatible with Nissa's format:
register "option" = "{
[0] = value /* comment */
...
}"
to
register "option[0]" = "value" /* comment */
BUG=none
TEST=abuild -v -a -x -c max -p none -t google/brya -b anraggar
Change-Id: I60659bd44813173f9b984216473a0919c5f331b8
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
acpi/dsdt_top.asl provides some common functionality and needs to be
included at the beginning of the DSDT.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia7b5ddce110b35ed65c6df6cc42995abe93a3ffc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79466
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Instead of including globalnvs.asl in the mainboard's dsdt.asl, include
it in Genoa's soc.asl. This aligns Genoa with Cezanne and newer and also
moves more SoC-common code to the SoC folder.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie0e3299a95e007188a4d9de824cfff8d25a778be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79465
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the MICRON MT62F1G32D2DS-023 WT:B RAM part for brox:
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
H9JCNNNBK3MLYR-N6E 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
MT62F1G32D2DS-023 WT:B 2 (0010)
BUG=b:311450057,b:315913909
BRANCH=None
TEST=Run part_id_gen tool without any errors
Change-Id: Id120a5eb311d8299a8e59d2c1658fe0742e93934
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Early versions of CB:76519 had more devices enabled in the chipset
devicetree which shouldn't necessarily be enabled in the chipset
devicetree. Enable most of those in the Onyx mainboard's devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieeb96755a007a5ca70e4c31df09325835bb8ef47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Disable the IOMMU PCI devices in the chipset devicetree. In order for
the IOMMU devices on the Onyx mainboard still be enabled, enable them in
the mainboard devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8c1bbbf370a3b5566a8484bcfa88dc4efa31222b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79409
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the device and chip entries for the various PCIe ports and MPIO
lane configuration. Below each PCIe bridge device with an external PCIe
port on the mainboard, an MPIO chip is added that provides the
corresponding MPIO configuration for this external PCIe port.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I8563c5a07eb8fd8ff9dd4e7b63fc9a7d485b1316
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78921
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drive board specific USB configuration from the coreboot devicetree into
the opensil input block.
In the process of scrubbing opensil for public release USB became non
functional.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I62eefe1061446612168dd27e673a2742903456c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78920
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Adjust PL1 max value from 15W to 25W
BUG=b:314263021
TEST=emerge-rex coreboot
Change-Id: I4122a13d7e33c736299c1a759ec51f7a3b29340f
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79377
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update proximity sensor tuning value from dedede/kracko tuning.
Remove GPIO override to use the configuration from nissa baseboard:
- GPP_B5 ==> SOC_I2C_SUB_SDA
- GPP_B6 ==> SOC_I2C_SUB_SCL
BUG=b:310050220
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I7c687677a797415d80be4c420484d3346a8455f6
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79247
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Updated Linux FW works with PCI gen3 speed and PSPP.
This reverts
commit 05c9a850fd21 ("mb/google/nipperkin: Fix WLAN to GEN2 speed")
https://review.coreboot.org/c/coreboot/+/63593
and
commit 76fddd963925 ("mb/google/nipperkin: Disable PSPP for WLAN")
https://review.coreboot.org/c/coreboot/+/63722
The changes are overlapped and are reverted together.
BUG=b:240426142 & b:228830362
The system is able to ran over 2500 cycles on Nipperkin with command
suspend_stress_test -c 10000 --wake_min 10 --suspend_min 10 \
--nofw_errors_fatal
The whole variant_update_dxio_descriptors is empty and is pushed back
to weak function.
Change-Id: Id207076542edc8ea0cabc6e02e29856c2b6803c7
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Enable BT offload when I2S option is selected for screebo.
BUG=b:275538390
TEST=Verified audio playback using BT speaker/headset in I2S mode on google/screebo.
Fixes: https://review.coreboot.org/c/coreboot/+/77755
Change-Id: I7ebe8e28d35428ce2fb8129dc145fec9ac60f9da
Signed-off-by: Terry Cheong <htcheong@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79378
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to TCPC0 & TCPC1 exchanged compare to Neried design,
but related USB2 Ports not exchanged, keep mainboard C port to conn0.
BUG=b:312998945
TEST=can boot from external Type-c USB disk
Change-Id: Ib8df4a256bd9cd1b2ca229b09d68f97babc8092e
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update brox devicetree based on the latest schematics.
- Configure typeC to EC mux ports settings.
- Configure USB2/USB3 ports settings.
- Configure TCSS ports settings.
BUG=b:311450057
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: Iac5a2e8be6cea64f107d267d4cf71529f08bb63d
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79391
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the support LP5 RAM parts for brox:
1. HYNIX LPDDR5 6400 2GB H9JCNNNBK3MLYR-N6E
2. MICRON LPDDR5 6400 4GB MT62F1G32D4DR-031 WT:B
DRAM Part Name ID to assign
H9JCNNNBK3MLYR-N6E 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
BUG=b:311450057
BRANCH=None
TEST=Run part_id_gen tool without any errors
Change-Id: Ib17f26a310435e37088191594863a645aa751440
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79392
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:305793886
TEST=util/abuild/abuild -p none -t google/rex -x -a -b deku
Change-Id: I41a64252f08304ffc66fd782e54720252064ca49
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Fix up the memory config for brox based on the schematics. Also,
since memory training needs to happen in romstage, initializing the
MEM_STRAP & MEM_CH_SEL gpios for use in romstage. Also consolidating
the GPIOs needing to be initialized in romstage into the baseboard
gpio.c file.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I17615cda7df10e73e49fb49f736728787ef7625d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
This patch allows variants to override the default baseboard PLx
limits.
Additionally, rearrange the include header files alphabetically.
BUG=b:313667378
TEST=Able to boot google/screebo with modified power limits.
Before:
[DEBUG] WEAK: src/mainboard/google/rex/variants/baseboard/rex/
ramstage.c/variant_devtree_update called
[INFO ] Overriding power limits PL1 (mW) (10000, 15000)
PL2 (mW) (40000, 40000) PL4 (W) (84)
After:
[INFO ] Overriding power limits PL1 (mW) (10000, 15000)
PL2 (mW) (40000, 40000) PL4 (W) (84)
Change-Id: Ic66872c530963238a0bf5eebbd5b5a76a7985e5c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
+-------------+----------------+------------+
| USB 2.0 | Connector Type | OC Mapping |
+-------------+----------------+------------+
| 1 | Type-C | OC_0 |
+-------------+----------------+------------+
| 2 | Type-C | OC_0 |
+-------------+----------------+------------+
| 3 | Type-C | OC-0 |
+-------------+----------------+------------+
| 4 | Type-A | OC_3 |
+-------------+----------------+------------+
| 5 | Type-C | OC_0 |
+-------------+----------------+------------+
| 6 | Type-A | OC_3 |
+-------------+----------------+------------+
| 7 | Type-A | OC_3 |
+-------------+----------------+------------+
| 8 | Type-A | OC_3 |
+-------------+----------------+------------+
| 9 | Type-A | OC_3 |
+-------------+----------------+------------+
| 10 | BT | NA |
+-------------+----------------+------------+
+---------------------+-------------------+------------+
| USB 3.2 Gen 2x1 | Connector Details | OC Mapping |
+---------------------+-------------------+------------+
| 1 | Type-A | OC_3 |
+---------------------+-------------------+------------+
| 2 | Type-A | OC_3 |
+---------------------+-------------------+------------+
+------+-------------------+------------+
| TCPx | Connector Details | OC Mapping |
+------+-------------------+------------+
| 1 | Type C port 0 | OC_0 |
+------+-------------------+------------+
| 2 | Type C port 1 | OC_0 |
+------+-------------------+------------+
| 3 | Type C port 2 | OC_0 |
+------+-------------------+------------+
| 4 | Type C port 3 | OC_0 |
+------+-------------------+------------+
BUG=b:305793886
TEST=util/abuild/abuild -p none -t google/rex -x -a -b deku
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I90d3d984af6d40efb4553cf5675617700161d2d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
