Age | Commit message (Collapse) | Author |
|
According to USB 2.0 Spec Table 7-7, the High-speed squelch
detection threshold Min 100mV and Max 150mV, and we set USB
2.0 PHY0 and PHY1 squelch detection threshold to 150mV by
default, so if the amplitude of differential voltage envelope
is < 150 mV, the USB 2.0 PHYs envelope detector will indicate
it as squelch.
On Kevin board, if we connect usb device with Samsung U2 cable,
we can see that the impedance of U2 cable is too big according
to the eye-diagram test report, and this cause serious signal
attenuation at the end of receiver, the amplitude of differential
voltage falls below 150mV.
This patch aims to reduce the PHY0 and PHY1 otg-ports squelch
detection threshold to 125mV (host-ports still use 150mV by
default), this is helpful to increase USB 2.0 PHY compatibility.
BRANCH=gru
BUG=chrome-os-partner:62320
TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into
Type-C port, check if the USB device can be detected.
Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e
Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/431015
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Inno Park <ih.yoo.park@samsung.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18462
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
As David commented the "Bob and other follow-ons match Gru, Kevin should
be the special case here", and update the calculations value for gru/bob
board.
From the actual tests, some regulator voltage than the actual set of less
than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the
{min, max} regulator voltage for Bob board. Make sure we get the accurate
voltage.
BUG=chrome-os-partner:61497
BRANCH=none
TEST=boot up Bob, measure the voltage for little cpu and C-logic.
Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4
Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/424523
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Original-Reviewed-by: Brian Norris <briannorris@chromium.org>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/430403
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18460
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch adds the DPTF settings specfic to the mainboard and enables
the CPU and other thermal sensors as participant device for poppy.
It enables the DPTF flag in the device tree for poppy. It also includes
the DPTF specific ASL file in the main DSDT definition.
BUG=None
BRANCH=None
TEST=Built for poppy.
Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17926
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
minnow3 doesn't build right now due to API divergence on master branch.
Follow up with recent changes.
Change-Id: Iee84750292f22aa040127bcbfe523a0b9eaa8176
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18476
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
Update GPIO controls and mainboard configurations for Rowan.
[pg: use the opportunity to clean-up the gerrit-rebase task list with
the entirely unrelated Ignore-CL-Reviewed-on lines]
BUG=chrome-os-partner:62672
BRANCH=none
TEST=emerge-rowan coreboot
Change-Id: I110fb368b3d9fa9dfb2bf091342dfb511ff7c09c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f4252cbe94a7456108aaa522e170bca5dcb1fdd1
Original-Change-Id: I18ebc3ccf4c7d051839d7c50e9b0682ef8f09830
Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/430557
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/341513
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/327003
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/355221
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/354670
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361360
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361361
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361362
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361363
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/382320
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405110
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405130
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/419795
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/424139
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430293
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430294
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430295
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427820
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427821
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427822
Reviewed-on: https://review.coreboot.org/18463
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The children of Gru should share the benefits. In the real world, Bob can't
pass the eye diagram tests.
BUG=chrome-os-partner:62714
BRANCH=firmware-gru-8785.B
TEST=build coreboot
Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd
Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/440745
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/441468
Reviewed-on: https://review.coreboot.org/18461
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
These parameters are probably the result of copying from the Thinkpad
X60 code.
Change-Id: I29763b38618d4b306c37424c5c4b57dfcf69424b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18290
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Copy GPIO table implementation from the google/reef board except
with board variant features removed. Also exlcude CrOS GPIO functions.
Remove previous romstage GPIO implementation in brd_gpio.h and romstage.c.
Configure GPIO settings for MinnowBoard 3.
Change-Id: Id2817dcf2f8f196ecd13c810f7f0010a115db566
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18375
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Set the proper memory configuration for the MinnowBoard 3. The current
values are copied from intel/leafhill. Set the proper values for
MinnowBoard 3.
Change-Id: Ie37842f5ce2cabaa892f42ee945c91fe3ace527a
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18374
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This commit adds the initial scaffolding for the MinnowBoard 3
with Apollo Lake silicon.
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with name changes. Special adaptations for MinnowBoard 3
mainboard will follow in separate commits.
Change-Id: I7563fe37c89511c7035c5bffc9b034b379cfcaf4
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18298
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I3ae80f5727e83a1c9210f0d13fa7fc32c5c79085
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18412
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins)
|
|
There was a 'typo' where the subsystem id was set instead of the codec
vendor id. This caused the lynxpoint HDA codecs init to fail to find
the proper codecid verbs so codecs were never initialized. That caused
the headphones jack to not work.
Change-Id: I975031643fc42937ecaea2300639b90632543f67
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18411
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I1fa72e59866ee4aad34d4b60e499f6e37acc367f
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18410
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The M.2 SSD is on the SATA port 3, which also required the DTLE setting
to be set.
This fixes issues with the M.2 SSD not being detected/stable.
Change-Id: Id39d9ec395a2d9d32be4c079678d0708f08b3935
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18409
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: I6a1810360b5c3210038670aea6e80312798a63cd
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18406
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is done to avoid any conflicts with same IRQ enums defined by other
drivers.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18444
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18322
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable Realtek RT5663 codec i2c device and add required
SSDT parameters.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=With required driver support in kernel verify audio on headset
Change-Id: I9b9eb1e7edca56870f5be0e4fd603c9b0dc7f9de
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18216
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable Maxim 98927 codec i2c device and add required
SSDT parameters.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=with required driver support in kernel verify audio on poppy
on-board speakers.
Change-Id: Id731de42d77204d59f32ac4c33a245837d6e2107
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://review.coreboot.org/18215
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
poppy board uses Maxim 98927 speaker codec and Realtek RT5663
for headset. Select the apropriate NHLT blobs to be packaged in CBFS.
Also, generate the required ACPI NHLT table for codec and the supported
topology in poppy.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=With the required driver support in kernel verify that
the Audio plays on on-board speakers and headset, recording
works from on-board mics and headset mics.
Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18214
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable Fast-Plus speed for the touchscreen device so it can
be used at 1MHz instead of 400KHz.
BUG=chrome-os-partner:61277
TEST=manual testing on Eve P1, needs backported kernel patches
to actually make use of any I2C speed other than 400KHz
Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18397
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add the audio devices to Eve mainboard:
- Describe Maxim 98927 speaker amps and RT5663 headphone codec
in ACPI so they can be enumerated by the OS.
- Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH.
BUG=chrome-os-partner:61009
TEST=manual testing on Eve P1 with updated kernel to ensure that
both speakers and headset are functional. DMIC support is
is still being worked on and is not yet functional.
Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18398
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Created using autoport plus some manual work and copying from G505S to
account for the non-H8 EC.
This model uses the same ENE KB9012 EC as the G505S.
Tested:
- Mainboard variant with 8GB Elpida DDR3
- SeaBIOS payload
- Booting into Linux 4.9.6 with Debian/unstable installed on the
internal HDD/SDD slot
- Native raminit
- Both native VGA init and option rom VGA init
- Basic TPM functionality (auto-detection and RNG)
- Battery status readout
- Basic ACPI functions (power button event; power-off; reboot)
- thinkpad-acpi hotkey functions
- thinkpad-acpi LED control (red thinkpad LED)
- Suspend to RAM and resume works
- Mini displayport output works
Known issues:
- Patches needed for EC battery support
https://review.coreboot.org/#/c/18348/
https://review.coreboot.org/#/c/18349/
- No thermal zone since temperature sensing is not H8-compatible
and needs to be reverse engineered.
Not tested:
- msata/wwan (probably works)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Change-Id: I52bc4515277e5c18afbb14a80a9ac788049f485c
Reviewed-on: https://review.coreboot.org/18351
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change config option selection from "config xyz default y" to "select
xyz" if the config option has no dependencies.
BUG=None
BRANCH=None
TEST=Verified that config option selection remains unchanged.
Change-Id: I259ae40623b7f4d5589e2caa0988419ba4fefda4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18400
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Since we are not using gpio regulators on reef anymore, remove the
selection from Kconfig as well.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18399
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This mainboard uses two i210 Ethernet controller. Therfore we enable the
usage of the i210 driver and have to provide a function to search for a
valid MAC address for all i210 devices by using Siemens hwilib.
Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18380
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Move code common code from each variant's mainboard.asl into
common ACPI code for all variants (like google/auron). This also
adds the _PRW method for the LID0 device for falco and peppy, which
omitted the function when they were originally upstreamed.
See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device
Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18368
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Apply the measured rise and fall times for I2C bus 1 on Eve
so it can be tuned properly for 400KHz operation.
BUG=chrome-os-partner:63020
TEST=verify I2C1 bus speed with a scope
Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18396
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently UART0 GPIOs are being put into native mode during FSP-S
stage, so have ramstage re-configure them back to regular GPIO mode.
GPP_C8 does not seem to be functioning properly when routed to the
APIC, possibly due to the UART0 being enabled even though it is unused,
which is required because UART0 is PCI 1e.0 and so must be present for
other 1e.x functions to be enumerated. Instead, use this pin as a GPIO
interrupt so it will be routed through the GPIO controller at IRQ 14.
GPP_C9 was inverted and was only working because the pin was being
re-configured in FSP-S.
Also export the reset gpio as a device property so it can be used by
the kernel driver, which will stop it from complaining at boot.
BUG=chrome-os-partner:61233
TEST=verify that the interrupt and device is functional in the OS
Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18395
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The hybrid driver select by DRIVERS_LENOVO_HYBRID_GRAPHICS doesn't work
for t400/t500.
Replace it with a custom romstage implementation.
Tested on Lenovo T500 with dual graphics:
* Intel Native GFX init
* AMD VBios
* GNU Linux 4.8.13
* SeaBios as payload
* Discrete is working (44 W)
* Integrated is working (24 W)
* Switchable is working (34 W)
** Both GPUs are enabled, with Intel being connected to the panel
** DRI_PRIME allows to use AMD GPU
** ACPI doesn't seem to work (no vgaswitcheroo)
Depends on Change-Id: I4dc00005270240c048272b2e4f52ae46ba1c9422
Depends on Change-Id: If389016f3bb0c4c2fd0b826914997a87a9137201
Change-Id: I7496876e9b434d4a2388e1ede27ac604670339b7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18010
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I4ed7a164323a71d95a37ea754ec923ca0c5e6219
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18388
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
|
|
It rewrites the results of receive enable stored in the upper nvram
region, to avoid running receive enable again.
Some debug info is also printed about the self-refresh registers.
(Not enforcing a reset here, since 0 does not necessarily mean it's
not in self-refresh).
Change-Id: Ib54bc5c7b0fed6d975ffc31f037b5179d9e5600b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17998
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Previously the raminit failed on hot reset and to work around this
issue it unconditionally did a cold reset.
This has the following issues:
* it's slow;
* when the OS issues a hot reset some disk drives expect their 5V
power supply to remain on, which gets cut off by a cold reset,
causing data corruption.
To fix this some steps in raminit must be ommited on the reset path.
This includes receive enable calibration.
To achieve this it stores receive enable results in RTC nvram for them
to be rewritten on the resume path.
Note: The same thing needs to be done on the S3 resume path.
Calling a hot reset after raminit "outb(0x6, 0cf9)" works.
Change-Id: I6601dd90aebd071a0de7cec070487b0f9845bc30
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18009
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
eve is based on Kabylake SoC hence select the appropriate
config.
Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18314
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
poppy is based on Kabylake SoC hence select the appropriate
config.
Change-Id: Ie339a3991eeccb8a7dba983a2b5ab5d1c996ce9d
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18313
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for generating digitizer node in SSDT using wacom i2c
driver.
BUG=None
BRANCH=None
TEST=Verified that the node shows up in SSDT.
Change-Id: If7e1e2463778c2ff7263eff995def149457edcde
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18373
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the newly added SPI SSDT generator for adding FPC device.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully. Verified that the SSDT entry matches the
entry in mainboard.asl
Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18343
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This commit makes a basic adjustment for GPIOs, device tree, flash map and
MRC settings. With these basic settings the mainboard boots into
Linux lubuntu 4.8.0-22-generic using SeaBIOS. More adjustments will follow.
Change-Id: Ia920d236814f2e6a9b777dd1e4b4feef0ddf7721
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18292
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Create the initial Sand variant which refers to the Reef.
Sand is APL board that derives from reference board Reef.
BRANCH=master
BUG=chrome-os-partner:62200
TEST=Build (as initial setup)
Signed-off-by: YH Lin <yueherngl@chromium.org>
Change-Id: Iba8c5653b6176676c759d2b48063f0c0c6cde625
Reviewed-on: https://review.coreboot.org/18324
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change touchpad HID to use with the Google Centroiding Touchpad driver.
BUG=chrome-os-partner:61088
TEST=`emerge-eve coreboot`
Change-Id: I199ff46f1a93d3eccc8c694742585dcf37b2373f
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/18359
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some variants need the internal pull resistor on GPIO_SSUS_40
set explicitly to pull down rather than disabling the pull,
in order for the ram-id to be read correctly via GPIO.
Correct this by adding a function to enable and set the internal pull
and define its use as needed in the board's variant.h.
Chromium source:
branch: firmware-gnawty-5216.239.B
/src/soc/intel/baytrail/baytrail/gpio.h#418
/src/mainboard/google/gnawty/romstage.c#60
Test: boot 4GB Candy board and observe correct RAM id, amount detected
Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18309
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Poppy doesn't support 8042 keyboard. Select
NO_FADT_8042 to disable 8042 in FADT header.
Kernel will not try to access 8042 region
if 8042.FADT=0
BUG=chrome-os-partner:61858
TEST=Boot OS and verify FADT 8042 flag
Change-Id: I00182eb4b059d4d9f0705d349dc98651e3955f0d
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/18311
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update DPTF parameters based on thermal team test result.
1. Update TSR2 trigger points.
TSR2 passive point: 70, critical point: 90
2. Set PL2 Max to 15W.
BUG=chrome-os-partner:61383
BRANCH=reef
TEST=build, boot on snappy, and verified by thermal team
Change-Id: I8d01d6c1d7eabd359ceb131f3cd10965d4ac2c42
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18318
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Performance degradation seen with current PL1 throttling rate as 8
seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1
throttling rate to 15 seconds, fps score improved.
BUG=chrome-os-partner:60038
BRANCH=reef
TEST=Built and tested on electro system
Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/18317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
|
|
There will be more follow-up changes.
BUG=chrome-os-partner:62377
BRANCH=None
TEST=emerge-scarlet coreboot libpayload
Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c
Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a
Original-Signed-off-by: philipchen <philipchen@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/433039
Original-Commit-Ready: Philip Chen <philipchen@chromium.org>
Original-Tested-by: Philip Chen <philipchen@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18296
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
It's an attempt to consolidate the access code, even if there are still
multiple implementations in the code.
Change-Id: I4b2b9cbc24a445f8fa4e0148f52fd15950535240
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18265
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since it checks for DDR3 style checksums, it's a more appropriate name.
Also make its configuration local for a future code move.
Change-Id: I417ae165579618d9215b8ca5f0500ff9a61af42f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18264
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Also make sure that no board changes behaviour because of that by adding
a static assert.
TEST=abuild over all builds still succeeds (where it doesn't if
DIMM_SPD_SIZE isn't set to 128 bytes for boards that use the
device/dram code).
Change-Id: Iddb962b16857ee859ddcf1b52d18da9b3be56449
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18254
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Reef is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I6dfddbfdb5a2ffbdfd77c5f49602bf68e9693a06
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18277
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Eve is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The WAK_STS bit is not set in a wake from G3, so the check for this
bit needs to only be done when checking for a wake from S3.
This change correctly enables the keyboard backlight in wake from G3
and only does not enable it during a wake from S3.
BUG=chrome-os-partner:58666
TEST=Use Refresh+Power to issue hard reset and ensure that the keyboard
backlight turns on like it does when waking from S5. Also force enter
hibernate with Alt+VolumeUp+H and then power back up and ensure that
the keyboard backlight is enabled when booting.
Change-Id: I44045950e38aa5e5ae96a79385d604791852c7e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18280
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When guado/rikku/tidus were rolled into jecht, an error was
made in set_power_led() as guado/rikku set the polarity
differently than tidus. Fix the power LED for guado/rikku
by setting the polarity correctly.
Test: boot guado/rikku and observe proper function of power LED
under S0, S3, and S5 power states.
Change-Id: I23072ac60bc9683776f748ca1326d98257c3c54f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18249
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Bit 16 in BLC_PWM_CTL enables brightness controls, but the
current value is generic. Use the proper value, obtained
by reading BLC_PWM_CTL while running the VBIOS.
Change-Id: Ib273359e1c285b405a9bb26fc217c2f7e255b99f
Signed-off-by: Francis Rowe <info@gluglug.org.uk>
Reviewed-on: https://review.coreboot.org/10624
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Reason for revert:
Pyro has two touchscreen sources: WACOM/ELAN.
It will not have both touchscreen IC in one system at the same time.
So the "probed" property of WACOM i2c device is mandatory to set for kernel
to know whether it exists before driver initializes it.
Otherwise in ELAN case, when driver fails to init WACOM i2c device, ACPI _OFF
will be invoked to set GPIO#152 low to cut off power.
BUG=chrome-os-partner:62371
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I30f467bd8720d959686dc14f7877e6bc11ea6213
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change fixes the two sets of pins that were swapped in the
map of DQS signals from CPU to DRAM for channel 1.
Although this does not appear to have any impact to the system it
does result in different register values for DQS pin mapping that
are programmed inside FSP.
BUG=chrome-os-partner:58666
TEST=This fix was verified against the current schematic and using
FSP debug output.
Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18279
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
same change as I49935e659bf67225d3f5db1b06acc2cd046dcd74
this is required for poppy board as well.
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=None
BRANCH=None
TEST=play test sound in OS over internal speaker
Change-Id: I1695e9198f8f78e9c5ad6df6c1ac073ac1762c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18282
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=chrome-os-partner:58666
TEST=play test sound in OS over internal speaker
Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18281
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch sets PL2 override value to 15W in RAPL registers.
BUG=chrome-os-partner:62110
BRANCH=reef
TEST=Apply new firmware to evaluate Octane benchmark score.
Change-Id: I51734051586753677129314b5273fb275c74f5d2
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/18283
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This allows for defaults to be applied to CMOS parameters
when cmos checksum is incorrect.
This probably results in changed cmos settings for current users of
these targets.
Change-Id: Ifec0093f4b0dbaa51b96812a041f0eaf5c58ee86
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17041
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Activate the IOMMU for the ASUS F2A85-M LE board.
Enable the IOMMU in `devicetree.cb` and build AGESA IOMMU code by
enabling the option in `buildOpts.c`.
ACPI and MPTABLES interrupt routers are already present since they are
syminks to the F2A85-M version.
```
$ uname -a
Linux nukunuku 4.8.5 #35 SMP Sun Oct 30 19:34:55 CET 2016 x86_64 GNU/Linux
$ lspci -s 0.2
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) I/O Memory Management Unit
$ dmesg | grep -i IOMMU
ACPI: IVRS 0x00000000BFFAFF70 000070 (v02 AMD AMDIOMMU 00000001 AMD 00000000)
AMD-Vi: Applying erratum 746 workaround for IOMMU at 0000:00:00.2
iommu: Adding device 0000:00:01.0 to group 0
[...]
iommu: Adding device 0000:00:18.5 to group 9
iommu: Adding device 0000:03:00.0 to group 8
AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
```
Change-Id: I6049fcfad53d16a99495d7a8fbc584c71e371d73
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18259
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with minimum changes. Special adaptations for MC APL1
mainboard will follow in separate commits.
Change-Id: If0b8a2bc21c99c3be4e6043e8febfb1b91ff0a63
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18272
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
|
|
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty,
heli, kip, orco, quawks, squawks, sumo, swanky, and winky using
their common reference board (rambi) as a base.
Chromium sources used:
firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...]
firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...]
firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...]
firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...]
firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...]
firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...]
firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*]
firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.]
firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data]
firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data]
firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...]
firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table]
firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...]
The same basic cleanup/changes are made here as with the initial BYT
variant commit:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
- Micron 2GB SPD file for kip with updated values renamed to distinguish
from same file used by other boards
Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18164
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
That status isn't needed and making it non-static helps gcc 4.9.2 (or
any compiler that insists on "standard C" behaviour with global const
initializers)
Change-Id: Ib1fbd5213d262e653f31564b106095b4a28292f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18266
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Reorder the items to minimize the differences.
Change-Id: I745ec70a990f997d87c2a0b6164ae127eb694ddf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17438
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Apollolake boards should use DMIC-4ch configuration in Kernel side and
use CaptureChannelMap in userspace to distinguish boards with different
number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will
not be required and hence removed.
BUG=chrome-os-partner:60827
TEST=Verify internal mic capture
TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works
Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/18252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
EC sets the logic level based on outstanding wake events. When GPIO_22
is configured as a level triggered interrupt, the events are not
cleared from the interrupt handler. Hence, we'd just be re-signalling
over and over causing an interrupt storm upon lid open. So, GPIO_22
needs to be configured as EDGE_SINGLE instead of LEVEL.
BUG=chrome-os-partner:62458
TEST=Lid close/open. check CPU usage using top. It should
not show 70% CPU usage.
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a
Reviewed-on: https://review.coreboot.org/18267
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Export PowerResource for WDT touchscreen device.
BUG=chrome-os-partner:62311, chrome-os-partner:60194,
chrome-os-partner:62371
BRANCH=reef
TEST=Compiles successfully.
Change-Id: Icc5be170353753201d3571c39b50e29424d4d6d3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18240
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. For ELAN, export reset GPIO as well as PowerResource
2. For WCOM, export PowerResource
BUG=chrome-os-partner:62311, chrome-os-partner:60194,
chrome-os-partner:62371
BRANCH=reef
TEST=Verified that touchscreen works on pyro with WCOM device on
power-on as well as after suspend/resume.
Change-Id: I0306e24e19bf821cd3e08fdacc0d78b494c9a92f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18239
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Linux kernel expects that power management with ACPI should always be
handled using PowerResource. However, some kernel drivers (e.g. ELAN
touchscreen) check to see if reset gpio is passed in by the BIOS to
decide whether the device loses power in suspend. Thus, until the kernel
has a better way for drivers to query if device lost power in suspend,
we need to allow passing in of GPIOs via _CRS as well as exporting
PowerResource to control power to the device.
Update mainboards to export reset GPIO as well as PowerResource for
ELAN touchscreen device.
BUG=chrome-os-partner:62311,chrome-os-partner:60194
BRANCH=reef
TEST=Verified that touchscreen works on power-on as well as after
suspend-resume.
Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18238
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
I2C data (GPIO_132) and Clk (GPIO_133) lines are pulled low during
standby states S3/S0ix. This causes leakage of power. To reduce the
leakage, we have to pull these lines high during S3/S0ix. This is
done by programming the IOSSTATE to HIz. Also note that we are using
the internal pull ups to keep at SOC at 1.8V and the I2C lines are
not floating.
BUG=chrome-os-partner:62428,chrome-os-partner:61651
TEST=Enter S3/S0ix. Measure trackpad power. It should be less
than 4mW. Also I2c lines should be pulled high in S3/S0ix.
Change-Id: I5570ac37ec3cc41f6463dd6b858fdb56a20a1733
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/18251
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
In order to pass type A USB2 eye diagram,
USB2 port#0/#1 PHY register will need to be overridden.
port#0:
PERPORTPETXISET = 7
PERPORTTXISET = 1
IUSBTXEMPHASISEN = 3
PERPORTTXPEHALF = 0
port#1:
PERPORTPETXISET = 7
PERPORTTXISET = 2
IUSBTXEMPHASISEN = 3
PERPORTTXPEHALF = 0
BUG=chrome-os-partner:59491
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I8e67a6f0192d1c0abf6ec4926c2a17e44c818948
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18229
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Wacom touchscreen is i2c hid device and it's the device that always
exists.
So no need to set "probed" property for it.
BUG=chrome-os-partner:61513
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I27fe18ceadd03029b826e0237f80132eda1089b0
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18227
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I877d4470b697d6a6d4652ed1c60028cdcbe8df98
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18143
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Follow i2c-hid spec definition, level trigger interrupt is required
for i2c-hid device.
BUG=chrome-os-partner:61513
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: Ia825bd0c898e71e2ee2bf411f117a49a8fb411b6
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18217
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This fixes building coreboot with -std=gnu11 on gcc 4.9.x
Also needs fix ups for asus/kcma-d8 and asus/kgpe-d16 due to the missing
type.
Change-Id: I920d492a1422433d7d4b4659b27f5a22914bc438
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18220
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
In order for PD charge events to properly notify the OS when a charger is
attached we need to enable the PD MCU device and event source from the EC.
Without this change the charging still happens, but the OS does not notice
and update the charge state icon in the Chrome OS UI.
BUG=chrome-os-partner:62206
BRANCH=none
TEST=plug in a charger to either port and see charge status updated to
indicate charging in the power_supply_info tool and the Chrome OS UI.
Change-Id: Ia6f63ac719b739326d313f657a68005c32f45b8d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18209
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add support for Lenovo Thinkpad L520.
The files are generated by autoport,
and are successfully tested on the board.
L520 has got 4MiB flash chip, that contains a "slim" ME
with 1.2MiB only. The flash IC has to be desoldered, as
it won't be accessible in circuit. It is located on top
of the mainboard right under the touchpad.
Test-setup:
Extract the following blobs from vendor BIOS:
* Intel Flash Descriptor
* Intel Management Engine
* Intel VBios
The laptop has been externaly flashed. It was able to
turn on the display and load SeaBIOS.
Latest debian has been booted from harddisk.
Latest fedora has been booted from USB flash drive.
The following hardware has been tested and is working:
* Display using Option Rom
* PCIe wifi
* Ethernet
* Keyboard, trackpoint and touchpad
* Some Fn functions keys
* Volume Keys (except mic mute)
* Status LEDs
* Audio (headphone jack only)
* USB ports
* Native raminit dual channel (2 DDR3-1333 DIMMs tested)
* SATA cdrom
* SATA harddrive
Broken:
* Some Fn functions keys
* Microphone mute button
* Speakers (but headphone jack gives sound)
Untested:
* Expansion slot
* SD card slot
* Docking station
* Native gfx init
The EHCI debug port is the first one on the right side.
Change-Id: Ic8943799b953bde09ff1daf8427ce5125a0778ca
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18003
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This commit makes the initial changes to support the Intel Leaf Hill
CRB with Apollo Lake silicon. Memory parameters and some GPIOs are set.
The google/reef directory is used as a template, and the same IFWI
stitching process as reef is used to generate a bootable image.
Apollo Lake silicon requires a boot media region called IFWI which includes
assets such as CSE firmware, PMC microcode, CPU microcode, and boot
firmware.
Change-Id: Id92f0458548e3054d86f5faa8152d58d902f4418
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18039
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This commit adds the initial scaffolding for the Intel Leafhill CRB
with Apollo Lake silicon.
The google/reef directory is used as a template. This commit only
makes the minimum changes to Kconfig and Kconfig.name needed for
the build bot to not have issues.
Change-Id: I088edee0e94ecfb4666fa31e08dbcfd24a81891b
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18038
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
1. Update DPTF CPU/TSR1 passive trigger points.
CPU passive point: 80
TSR1 passive point: 46
2. Update DPTF TRT Sample Period
TSR1: 8s
BUG=chrome-os-partner:62133
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I8fcf750ac17b8894ed3c8704eec62f5071d9cf24
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18174
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The same GPIOs are used on both platforms, definitions are added an a
new .h to make it easier to re-use them across the code.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=panel backlight still enabled on Gru as before. The rest of the
GPIOs are used in the upcoming patches.
Change-Id: I54ef3e8dd79670bdb037baeec91430113d11bcc1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c58788026f28af52c650da0159b93d97269ca4a9
Original-Change-Id: I1a6c5b5beb82ffcc5fea397e8e9ec2f183f4a7e0
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346219
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/18176
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update the DPTF parameters based on thermal test result.
(ZHT_DPTF_EVT2_v0.4_20170120.xlsx)
1. Update DPTF TSR1 passive trigger point.
TSR1 passive point: 46
BUG=chrome-os-partner:60038
BRANCH=master
TEST=build and boot on electro dut
Change-Id: If35e4cf2dbf7c506534c52a052598f6204d5315a
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18183
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The devicetree settings were incorrect in a few places with
respect to the SOC and board design:
- IMVP8 VR workaround is for MP2939 and not MP2949 on Eve
- IccMax values are incorrect according to KBL-Y EDS
- USB2[6] is incorrectly labeled
- I2C touch devices do not need probed as they are not optional
- PCIe Root Port 5 should be enabled
- I2C5 device should not be enabled as it is unused
BUG=chrome-os-partner:58666
TEST=manually tested on Eve board
Change-Id: I74e092444ead4b40c6d8091b80a691d44e2c6c7d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18200
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to get quick boot speeds into recovery enable the
feature that allows for a separate recovery MRC cache.
This requires shuffling the FMAP around a bit in order to
provide another region for the recovery MRC cache. To make
that shuffling easier, group the RW components into another
sub-region so it can use relative addresses.
BUG=chrome-os-partner:58666
TEST=manual testing on eve: check that recovery uses the MRC
cache, and that normal mode does too. Check that if cache is
retrained in recovery mode it is also retrained in normal mode.
Also check that events show up in the log when retrain happens.
Change-Id: I6a9507eb0b919b3af2752e2499904cc62509c06a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18199
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the keyboard backlight as early in boot as possible to
provide a indication that the BIOS is executing.
Since this is bootblock it can't use the convenience function
for checking for S3 resume so just read the PM1 value from the
SOC and check it directly.
Use a value of 75% for the current system as that is visible
without being full brightness.
BUG=chrome-os-partner:61464
TEST=boot on eve and check that keyboard backlight is enabled
as soon as the SOC starts booting
Change-Id: I9ac78e9c3913a2776943088f35142afe3ffef056
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18197
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The PP1800_S rail is turned off in S3. However, enabling internal
pullups on the pins which are connected to PP1800_S results in
leakage into the P1800_S rail. Fix this by disabling the internal
pullups on PP1800_S rail pins.
BUG=chrome-os-partner:61968
BRANCH=reef
TEST=measured leakage on PP1800_S rail. Gone with this patch.
Change-Id: I5ae92b31c1a633f59d425f4105b8db1c9c18c808
Signed-off-by: Aaron Duribn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ic8149b1dd19d70935e00881cffa7ead0960d1c78
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18154
Tested-by: build bot (Jenkins)
Reviewed-by: Piotr Król <piotr.krol@3mdeb.com>
|
|
Installed memory only, PCB revision cannot be detected.
Change-Id: Ib6224018db3de4a7ddd9e6f7f30edc438c3f0702
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18153
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ie4f80619d9417200a007fc65154b97a5bc05f2f8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18152
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This string should not include manufacturer name.
Change-Id: I63793b16129334ea4930b8b0264a39d7f9849bba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18151
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Assembled SoC part does not have integrated graphics.
Change-Id: I5d157063cd850d343df73d448e6904c188a09730
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18150
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add weida touchscreen as 2nd touchscreen source
BUG=chrome-os-partner:61865
BRANCH=reef
TEST=emerge-snappy coreboot, and verified that touchscreen works on
snappy.
Change-Id: If76312a62e97da9d5de18ad895e90ee6b0f0c6ae
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18166
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
ELAN touchscreen device expects firmware to export GPIOs and ACPI
regulators for managing power to the device. Thus, provide the
required ACPI elements for OS driver to properly manage this device.
BUG=None
BRANCH=None
TEST=Verified that touchscreen works properly on boot-up and after
suspend/resume.
Change-Id: I78e0c35f60289afe338d140d90784a433ca534ae
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18163
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- Remove the 0mA entry for the charger performance table
- Slightly raise the passive limit for TSR2/TSR3 to 55C
BUG=chrome-os-partner:58666
TEST=manual testing on P1 system
Change-Id: I75c66afe04afbbdb64a45833eb938e57ff21b392
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18172
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the ACPI interface to EC driven keyboard backlight.
BUG=chrome-os-partner:61464
TEST=manual testing on P1 system
Change-Id: I13d96c13d7db726b1e8289131db65104bd302efe
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18171
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable an internal pull-up on ACPRESENT signal.
BUG=chrome-os-partner:58666
TEST=manual testing on P1
Change-Id: I0bb86f4547272e021ffd10998faa0e2f103b0808
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18170
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The following devices i2c6, i2c7, spi1, spi2, uart3 are not used.
BUG=none
BRANCH=master
TEST=emerge-snappy coreboot chromeos-bootimage
Change-Id: I9bacdbdd194ce21686c1618494d113402f2bef6c
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18140
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Audio DMIC PLL needs to be ON in S0ix to support
Wake on Voice. This requires GPIO_79 and GPIO_80
to be configured as IGNORE IOSSTATE. So DMIC CLKs
will be ON in S0ix.
Change-Id: If91045a8664ce853366b670b9db38d620818fbab
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/18155
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit 01ba8cf7 (mainboard/google/snappy: Add PowerResource
for ELAN touchscreen)
Change was out of date and broke the build.
Change-Id: Id47631ece1172c3f93bf6f40b8686dfd728842a9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18158
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|