summaryrefslogtreecommitdiff
path: root/src/mainboard
AgeCommit message (Collapse)Author
2020-07-26mb/google/kukui: send SKU ID to EC for device-specific configurationHung-Te Lin
For devices sharing same firmware, there may be few customization based on SKU ID - for example being clamshell or form factor. On Kukui and Jacuzzi platforms the SKU ID is defined on AP SOC, so we have to send the information to EC. BUG=b:161767717 TEST=make -j # builds and boots on Juniper BRANCH=kukui Change-Id: I8ffdd9fd1e609c1dd4b0e22dc7aab560ccdc842e Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43788 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/mainboard/dedede: update GPIO table for Botenyan.liu
Adjust GPIO setting to match boten design BUG=b:160741777 BRANCH=NONE TEST=Add gpio.c for boten Signed-off-by: Yan Liu <yan.liu@bitland.corp-partner.google.com> Change-Id: I4eafee608f657f8ec5a06caf6e99b08b3330512b Reviewed-on: https://review.coreboot.org/c/coreboot/+/43277 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/google/dedede: Change HDMI DDC GPIOs to native functionMaulik V Vaghela
HDMI DDC GPIOs were configured as NC till now in waddledoo. This may cause HDMI i2c transfer to break and EDID read will fail due to wrong configuration Configuring these GPIOs as NF in coreboot to fix the issue. BUG=b:160324327 BRANCH=None TEST=HDMI works on DDI2 onn Type-C port Change-Id: If02f062132d7c3b01b07ea9401e81f451df35c3c Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43294 Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/google/vilboz: Tune I2C bus 3 clockpeichao.wang
Tune I2C bus3 frequency and insure it meets I2C spec. BUG=b:161650117 TEST=flash coreboot to the DUT and actual measured I2C bus3 make sure it meet Spec. Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com> Change-Id: Ifa9f0bce723f55a12fd2313788c995f8326e3e7d Reviewed-on: https://review.coreboot.org/c/coreboot/+/43661 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26src: Change BOOL CONFIG_ to CONFIG() in comments & stringsMartin Roth
The Kconfig lint tool checks for cases of the code using BOOL type Kconfig options directly instead of with CONFIG() and will print out warnings about it. It gets confused by these references in comments and strings. To fix it so that it can find the real issues, just update these as we would with real issues. Signed-off-by: Martin Roth <martin@coreboot.org> Change-Id: I5c37f0ee103721c97483d07a368c0b813e3f25c0 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43824 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-26mb/emulation/qemu-i440fx/northbridge.c: Use SMBIOS macrosElyes HAOUAS
Change-Id: I0297c8c4008d9e448793c38a3758dced9ede0d7e Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43587 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-26mb/intel/tglrvp: Update MAINBOARD_PART_NUMBERAnil Kumar
- Update MAINBOARD_PART_NUMBER for TGL variants - MAINBOARD_PART_NUMBER is reported as FRID on acpi - This is required for cros_config to differentiate across TGL variants. - Mosys uses cros_config to identify TGL variants using data read from FRID Bug=none Test=build and boot coreboot on TGLRVP UP3 hardware Signed-off-by: Anil Kumar <anil.kumar.k@intel.com> Change-Id: I11d4ab2a5b6ade6c50988a9fec4d9866fe79d7b5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43620 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jack Rosenthal <jrosenth@chromium.org> Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com> Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
2020-07-26mb/asus/p2b: Enable hardware monitor access via I/O on ISA busKeith Hui
Set up a 8-byte I/O range at 0x290-0x297 as PIIX4's generic device 9, which activates a chip select when this range is accessed. On the P2B family it connects to the W83781D hardware monitor, allowing access to it over the ISA bus, just like vendor firmware. Apparently this does not work on p3b-f, but no ill effects observed either. TEST=On p2b-ls lm-sensors can detect chip and get readings over ISA. Change-Id: Iaed1df7230359e94c580c305f4769c8bb4f5fce0 Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41561 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-26src: Remove unneeded space in license headerElyes HAOUAS
Change-Id: Iac0f0c3d102a9a900ac168f8be907349d9a3dd42 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43565 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/google/dedede/var/drawcia: Add G2Touch touchscreen supportWisley Chen
BUG=b:155002684 TEST=build drawcia, and check touchscreen can work Change-Id: I29a891e07bb3c1d8ebe17666c18bfcf3bc1c361d Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43551 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
2020-07-26Kconfig: Remove unnecessary choice namesMartin Roth
The only reason to use a named choice statement is if you plan on having the choice statement in multiple places. Since none of these are used in multiple places, we can get rid of the names. Signed-off-by: Martin Roth <martin@coreboot.org> Change-Id: Ie5f84e9dc38050234976bd193ac5fbf649e564f4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43765 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-26mb/asus/p2b: Drop select SMPKyösti Mälkki
Variants that select BASE_ASUS_P2B_D will also get MAX_CPUS==2 below, so this was redundant. Change-Id: I9048a4821f19d90e1489b09e294d2551941abf10 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43809 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26src: Remove unused 'include <cbmem.h>'Elyes HAOUAS
Change-Id: Ib41341b42904dc3050a97b70966dde7e46057d6b Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43362 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-26mb/x/acpi_tables: Do minor cleanup on includesKyösti Mälkki
Change-Id: I7a6ddf95d085490d52e00ade7bac23e8c8849427 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42865 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26src: Remove extra lines in license headerElyes HAOUAS
Change-Id: I7378aa7d6156ece3ab3959707a69f45886f86d21 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43593 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/emulation/qemu-aarch64: Fix up license headerAngel Pons
Change-Id: I9730680a8359407a2a03dbb7243a6547420e1f39 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43856 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26*/mb/google/volteer/**/gpio.h: Fix up license headerAngel Pons
There's a `GPL-2.0-or-later` version of this file in volteer2, so use it in place of these weirdly-licensed files. Change-Id: Icde2f6539d9c726d6967350f74e7bc015e01e7b5 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43855 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-07-26skylake boards: Factor out copy-pasted PIRQ routesAngel Pons
Put them in common code just in case something depends on the values. Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Michael Niewöhner Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/intel/saddlebrook/devicetree.cb: Use PCH_IRQ* macrosAngel Pons
Tested with BUILD_TIMELESS=1, its coreboot.rom does not change. Change-Id: I6375f97bc2a30beba5882792328f26e0675621cc Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43867 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/google/zork: remove ACPI_FADT_RESET_REGISTER from fadt_flagsFelix Held
This applies what commit 79572e4f32f844f60338d1aafdba6b94f4111a5c does to the devicetree settings of the zork devices. Change-Id: Ife94818d771f137e56c51ad1598148f60fcf5345 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43820 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26mb/amd/mandolin: add default USB2 PHY tune parameters to devicetreeFelix Held
Change-Id: I4ea2fb83522d8810fe84e0a3f42bf44f2f911461 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43819 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-26amd/picasso: rework USB2 PHY tune parameter handlingFelix Held
BUG=b:161923068 Change-Id: I67f23c0602e345fbd806e661a4462cf07f93ef64 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43783 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-25soc/amd/picasso: don't apply unconfigured USB2 PHY tune parametersFelix Held
Since FSP pre-populates the UPD struct with the non-zero default values, coreboot shouldn't set them to zero in the case that they aren't configured in the board's devicetree. Since all parameters being zero is a valid case, this patch adds another devicetree option that applying the devicetree settings for the USB2 PHY tuning depends on being set. BUG=b:161923068 Change-Id: I66e5811ce64298b0644d2881420634a8ce1379d7 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43781 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-25mb/intel/cedarisland: undo set trig and bufdis for NF padsMaxim Polyakov
According to the documentation [1], RX Level/Edge Configuration (trig) and GPIO Tx/Rx Buffer Disable (bufdis) [2] settings are not applicable in native mode and BIOS does not need to configure them. Therefore, there is no need to configure this in gpio.h using PAD_CFG_NF_BUF_TRIG macros. Use PAD_CFG_NF instead and set this fields to 0. [1] Intel document #549921 [2] Intel document #336067-007US This is part of the patch set "src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ": CB:43455 - cedarisland: undo set trig and bufdis for NF pads CB:43454 - tiogapass: undo set trig and bufdis for NF pads CB:43561 - h110m: undo set trig and bufdis for NF pads CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG Change-Id: Ie3ee2eadc08826d49e8517c83ab6831398e3aa93 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43455 Reviewed-by: Michael Niewöhner Reviewed-by: Lance Zhao Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-25mb/getac/p470/acpi_tables.c: Remove wrong commentElyes HAOUAS
Change-Id: I85c20d282949b51efd7cdd6f6e79b0b84ff62e2b Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43588 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-25soc/intel/tigerlake: Set power limits for Tiger Lake Y-SKUSumeet R Pawnikar
Set power limits in devicetree for Tiger Lake Y-SKU based volteer variant boards. BUG=b:152639350 BRANCH=None TEST=Built and tested power limits on volteer variant board. Change-Id: If4f1226473b48365e5962df9fff29910c99007fc Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43607 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Caveh Jalali <caveh@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24mb/supermicro/x11-lga1151: Clean up gpio.hMaxim Polyakov
- remove comments (except the GPIO group), because it does not contain useful information that helps to understand the circuit, which we do not have; - remove empty lines between macros; - use a shorter PAD_CFG_GPI_INT() macro instead of PAD_CFG_GPI_TRIG_OWN() to set DRIVER mode. Change-Id: Ia7111341aab6f400da70d936849e4d4c9406905b Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43409 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner
2020-07-24supermicro/x11-lga1151/gpio: 4/4 Convert field macros to PAD_CFGMaxim Polyakov
Converts bit field macros to target PAD_CFG_*() macros, which were hidden in the comments. To do this, the following command was used: ./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/ x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h ./intelp2m -n -t 1 -p snr -file ../../src/mainboard/supermicro/ x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h This is part of the patch set "mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m": CB:42916 - 1/4 Decode raw register values CB:42917 - 2/4 Exclude fields for PAD_CFG CB:42918 - 3/4 Fixes some field macro CB:35679 - 4/4 Convert field macros to PAD_CFG Tested with BUILD_TIMELESS=1, Supermicro X11SSH-TF and X11SSM-F, remains identical. Change-Id: Idad7536854d4b1ae7dcf7934e81de438478fe059 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35679 Reviewed-by: Michael Niewöhner Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24supermicro/x11-lga1151/gpio: 3/4 Fixes some field macroMaxim Polyakov
Fixes some bit fields to convert to target macros PAD_CFG_*() macros. This is part of the patch set "mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m": CB:42916 - 1/4 Decode raw register values CB:42917 - 2/4 Exclude fields for PAD_CFG CB:42918 - 3/4 Fixes some field macro CB:35679 - 4/4 Convert field macros to PAD_CFG Change-Id: I291f5f0f34505c466b610aa4049c8cc35937d140 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42918 Reviewed-by: Michael Niewöhner Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24supermicro/x11-lga1151/gpio: 2/4 Exclude fields for PAD_CFGMaxim Polyakov
This patch excludes bit fields that should be ignored [1] in order to convert current macros to target PAD_CFG_*() macros. The following commands were used for this: ./intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/ supermicro/x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h /intelp2m -ii -fld cb -ign -t 1 -p snr -file ../../src/mainboard/ supermicro/x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h [1] ignore RX Level/Edge Configuration (bit 26:25) and RX/TX Buffer Disable (bit 9:8) for the native function, because it does not affect the pad in this mode. This is part of the patch set "mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m": CB:42916 - 1/4 Decode raw register values CB:42917 - 2/4 Exclude fields for PAD_CFG CB:42918 - 3/4 Fixes some field macro CB:35679 - 4/4 Convert field macros to PAD_CFG Change-Id: Icdf366a8d416598cec5afcb9a0fae6bf7ecd7ba0 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42917 Reviewed-by: Michael Niewöhner Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24mb/google/volteer: Remove unused dptf.asl filesTim Wawrzynczak
In the middle of the Great DPTF Refactor of 2020, new volteer variants were added, but their dptf.asl files are no longer used, so delete them. Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: I52f2042aa870a29026eb9fe122340ad07654e706 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43828 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Caveh Jalali <caveh@chromium.org>
2020-07-24supermicro/x11-lga1151/gpio: 1/4 Decode raw register valuesMaxim Polyakov
Use the intelp2m utility [1,2] with -fld=cb options to convert the pad configuration format with the raw values of the DW0 and DW1 registers to the format with the bit fields macros: PAD_FUNC(), PAD_RESET(), PAD_TRIG(), PAD_BUF(), PAD_PULL(), etc... Also use the -ii options to generate the target macro in the comments, so that it is easier to understand what result we should get: ./intelp2m -ii -fld cb -t 1 -p snr -file ../../src/mainboard/supermicro/ x11-lga1151-series/variants/x11ssm-f/include/variant/gpio.h ./intelp2m -ii -fld cb -t 1 -p snr -file ../../src/mainboard/supermicro/ x11-lga1151-series/variants/x11ssh-tf/include/variant/gpio.h [1] https://github.com/maxpoliak/pch-pads-parser [2] https://review.coreboot.org/c/coreboot/+/35643 This is part of the patch set "mb/supermicro/x11-lga1151: Rewrite pad config using intelp2m": CB:42916 - 1/4 Decode raw register values CB:42917 - 2/4 Exclude fields for PAD_CFG CB:42918 - 3/4 Fixes some field macro CB:35679 - 4/4 Convert field macros to PAD_CFG Tested with BUILD_TIMELESS=1, Supermicro X11SSH-TF and X11SSM-F, remains identical. Change-Id: I209ecdca75a0e62233d3726942c75ea06acc40a2 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42916 Reviewed-by: Michael Niewöhner Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24mb/ocp/tiogapass: Use macro to configure IIOMaxim Polyakov
Use macros to configure each of the IIO ports instead of an array of some unknown parameters. This will clean up the code and make it easier to read. Tested with BUILD_TIMELESS=1, Tioga Pass, remains identical. Change-Id: I2911992435a6c93624525426d56212f821abb866 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43502 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Jonathan Zhang <jonzhang@fb.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24mb/ocp/deltalake: Send OEM IPMI command for CMOS clear on RTC failureJingle Hsu
When RTC failure is detected, send IPMI OEM command to issue CMOS clear. This is to let the payload (LinuxBoot) handle the IPMI OEM CMOS clear command by resetting RTC data, erasing RW_VPD (TODO) and add a SEL, then reboot the system. Tested=on OCP Delta Lake, after removing RTC battery we can see the above flow can be executed correctly. Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com> Change-Id: I27428c02e99040754e15e07782ec1ad8524def2f Reviewed-on: https://review.coreboot.org/c/coreboot/+/43005 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24mb/ocp/tiogapass: Populate SMBIOS data and set the read PPIN to BMCJohnny Lin
1. Populate SMBIOS data from OCP_DMI driver read from FRU 2. Set the read PPIN MSR for CPU0 and CPU1 to BMC, selecting PARALLEL_MP_AP_WORK to enable OCP DMI driver to read remote socket PPIN. Tested on OCP Tioga Pass. Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com> Change-Id: Ie11ab68267438ea9c669c809985c0c2d7578280e Reviewed-on: https://review.coreboot.org/c/coreboot/+/40524 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-24mb/google/octopus/variants/garg: update Garfour SKU IDTony Huang
SKUID 51 - Garfour EVT (non-touch, TypeA DB) 52 - Garfour DVT (touch, HDMI DB) BUG=b:161554087 BRANCH=octopus TEST=emerge-octopus coreboot chromeos-bootimage Change-Id: I3cb17c2b665c303da210817a531c869c6324b249 Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43670 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Henry Sun <henrysun@google.com>
2020-07-23mb/google/zork: Don't expose reset GPIO for touchscreen to OSRaul E Rangel
The Raydium ACPI entry currently provides a reset GPIO and an _ON/_OFF method to the kernel. These are contradictory. The ownership of the GPIO should be mutually exclusive between either the OS or the FW. Since we have two methods exposed this causes the OS to reset the TS twice. Once using the _ON method, and once using the GPIO. Additionally the _ON method is waiting for 20ms after reset while the OS driver uses a 50ms delay. The Raydium TS datasheet specifies 20ms for FW ready time, so the OS driver is adding additional padding. The reference design has a 32ms rise time on the reset line. So without this patch, the OS tries to reset the TS using the _ON method and it waits for 20ms. This is not enough time for the reset line to reach high, let alone account for the FW ready time. The OS driver then tries to reset the device by toggling the GPIO. It waits 50ms which is still 2ms less than required. This CL removes the GPIO from being exported in the _CRS so the OS driver won't try and reset the device. It also increases the reset delay by 32ms to account for the rise time. This isn't a complete fix. I think that the slow rise time is causing some kind of metastability in the TS reset hardware. Using a script to bind and unbind the TS driver, the TS device becomes unresponsive after ~200 iterations. The only way to reset the device is to power cycle. The TS power is also not currently controlled by the power resource. This means that we have no guarantee over when the reset line is toggled. This will lead to issues while spending and resuming. BUG=b:160854397 TEST=Boot trembyle and make sure TS works. Suspend/Resume trembyle 300+ times. Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I23131be5d7109eed660a8bd6e2c156c015aa3c4e Reviewed-on: https://review.coreboot.org/c/coreboot/+/43467 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-07-23mb/google/zork/variants/dalboz: Use HS200 for eMMCEric Peers
Earlier versions of Dalboz did not correctly handle HS400. One fix was to add stitching vias, but these boards did not have them. b/156539551 Another possible fix is to add tuning parameters including drive strength, but that is still a WIP. b/158959725 This should correct OS load failures in the meantime by running the bus slower. BUG=b:158845662 TEST=build, flash, boot sku 0x5a80000c to OS BRANCH=None Signed-off-by: Eric Peers <epeers@google.com> Change-Id: Ia3e7a641bde04c5a7be29bf91c38dd8c110ed17a Reviewed-on: https://review.coreboot.org/c/coreboot/+/43572 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Raul Rangel <rrangel@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-23zork: Create dirinboz variantKevin Chiu
Create the dirinboz variant of the dalboz reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.1.1). BUG=b:161579679 BRANCH=master TEST=util/abuild/abuild -p none -t google/zork -x -a make sure the build includes GOOGLE_DIRINBOZ Change-Id: I33c03080ffbe0bca61acf4144417b9f5fff6389f Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43601 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-07-23mb/google/arcada: Enable bayhub 720 on ArcadaMark Hsieh
Add PCIe-eMMC bridge bayhub 720 on Arcada to the devicetree. BUG=b:157971972 BRANCH=sarien TEST=local build and boot from SATA/PCIe-eMMC storage successfully Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com> Change-Id: I7e925730e57806e7398684dffd0d3bd1f4f9deeb Reviewed-on: https://review.coreboot.org/c/coreboot/+/43669 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Mathew King <mathewk@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-23mb/google/sarien: Enable bayhub 720 on SarienIvy Jian
Add PCIe-eMMC bridge bayhub 720 on Sarien. BUG=b:157971972 BRANCH=sarien TEST=local build and boot from storage successfully Change-Id: I28f40a420d51f476487655548f386cfbdc2e5329 Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42740 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Mathew King <mathewk@chromium.org>
2020-07-23mb/google/dedede/var/waddledoo: Configure stop delay for SiS TSKarthikeyan Ramasubramanian
Reset the Touchscreen (TS) and disable the stop GPIO (report switch) at the same time. Add a delay of 100 ms after disabling the stop GPIO. This will ensure the required delay is inserted for both reset and stop disable GPIOs simultaneously. BUG=b:152936541 TEST=Build and boot the waddledoo mainboard. Ensure that the SiS Touchscreen is functional. Change-Id: Icbfb5e07a28ab72b1ff696ad1183a6c2173dcaac Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43453 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Marco Chen <marcochen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-23mb/google/dedede/var/drawcia: Generate SPD ID for supported partsKarthikeyan Ramasubramanian
Add supported memory parts in the mem_list_variant.txt and generate the SPD ID for the parts. The memory parts being added are: H9HCNNNBKMMLXR-NEE K4U6E3S4AA-MGCR BUG=None TEST=Build the drawcia board. Change-Id: Id05c0b2a87b64bfedc761949cbc8ad6cf7dd73a5 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43505 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Marco Chen <marcochen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-23mb/google/zork: Fix Goodix touchscreen ACPI nodeFurquan Shaikh
This change does the following: a. USI_REPORT_EN is no longer set to high in coreboot. Instead GPIO_144 is exposed as stop_gpio in ACPI to allow OS to control this pad as required. b. Appropriate delays are added for power-down sequencing: - Delay after REPORT_EN is disabled - 1ms - Delay after RESET is asserted - 1ms BUG=b:159501288 Signed-off-by: Furquan Shaikh <furquan@google.com> Change-Id: If4d12fa0d4f4e5123d8fdccdabda996dcafa4523 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43701 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-23mb/google/zork/var/morphius: Change hid and desc for Goodix touchscreenFurquan Shaikh
Morphius uses Goodix touchscreen and not G2 touchscreen. This change updates hid and desc properties in devicetree accordingly. BUG=b:159501288 Signed-off-by: Furquan Shaikh <furquan@google.com> Change-Id: I2527fa5409bb127ac225c6fb2a5f1bc24895f6cc Reviewed-on: https://review.coreboot.org/c/coreboot/+/43700 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-23mb/google/zork: Drop TODO for GPIO_91Furquan Shaikh
GPIO_91 is added to ACPI using the device tree entry for codec. So, this change drops the TODO from GPIO table. Change-Id: I9c2e91465ab554126531f8512028360ae5fb316d Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43699 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-23mb/google/zork: Configure all pads in ramstage for dalboz referenceFurquan Shaikh
This change configures all missing pads in ramstage for dalboz reference. This ensures that the state of all pads is set correctly for the payload/OS. Also, all the pads for the platform are configured in baseboard gpio table in ramstage to ensure that variants can override any pads if required. BUG=b:154351731 Change-Id: Ia30da908d3827177a7b3594ffba38bff81018ab9 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43698 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-23mb/google/zork: Configure all pads in ramstage for trembyle referenceFurquan Shaikh
This change configures all missing pads in ramstage for trembyle reference. This ensures that the state of all pads is set correctly for the payload/OS. Also, all the pads for the platform are configured in baseboard gpio table in ramstage to ensure that variants can override any pads if required. BUG=b:154351731 Change-Id: Idd827b6a4f995546493596f22249f8699bdf526b Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43697 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-23mb/google/zork: Remove unnecessary PULL_UP from early_gpio_tableFurquan Shaikh
This change drops PULL_UP configured on pads in early_gpio table since these pads have external pulls. BUG=b:154351731 Change-Id: Id270e7b4f83dfa942655f513776a3b1c15c9678d Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43696 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-23amd/picasso: rename PCIe descriptor to DXIO descriptorFelix Held
Most of the DXIO descriptors are used to configure PCIe engines and lanes, but on Picasso system some of the DXIO lanes can also be configured as SATA or XGBE ports. Change-Id: I28da1b21cf0de1813d87a6873b8d4ef3c1e0e9dd Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43675 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-23vc/amd/fsp/picasso: add logical to lane number in port descriptor structFelix Held
The lane numbers in the PCIe/DXIO descriptor are the logical and not the physical ones, so add logical to the corresponding field names of the fsp_pcie_descriptor struct. Change-Id: I7037fed225119218e87593932815aff815e83ff8 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43660 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-23mb/google/kukui: Add new configs 'esche' and 'burnet'Kevin Chiu
new boards introduced to Kukui family. esche: clamshell burnet: 360 convertible BUG=b:161768221 BRANCH=master TEST=emerge-jacuzzi coreboot Change-Id: I2245c34533549bb94c58938fee5778b8a03e2767 Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43667 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2020-07-23mb/prodrive/hermes: Update VBT fileChristian Walter
Update .vbt file to support two DP outputs. Change-Id: Ifd4163aafe4ef3070d04a72a4699303af72c5102 Signed-off-by: Christian Walter <christian.walter@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43447 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-23ec/system76_ec: add support for System76 ECJeremy Soller
This adds ACPI code for System76 EC and converts system76/lemp9 to use EC_SYSTEM76_EC. Tested on system76/lemp9. Signed-off-by: Jeremy Soller <jeremy@system76.com> Change-Id: I1f693268d94b693b6764e4a3baf4c3180689f3be Reviewed-on: https://review.coreboot.org/c/coreboot/+/43612 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Reviewed-by: Michael Niewöhner
2020-07-23mb/ocp/deltalake: Add ipmi POST start command in romstageTimChu
Add function to send POST start command to BMC. This function is used in romstage and the POST end command will be sent in u-root. TEST=Read POST command log in OpenBMC, if command received successfully, message may show as below, root@bmc-oob:~# cat /var/log/messages |grep -i "POST" 2020 Jul 15 16:36:11 bmc-oob. user.info fby3-v2020.23.1: ipmid: POST Start Event for Payload#2 root@bmc-oob:~# Signed-off-by: TimChu <Tim.Chu@quantatw.com> Change-Id: Ide0e2a52876db555ed8b5e919215e85731fd80ed Reviewed-on: https://review.coreboot.org/c/coreboot/+/41605 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-23mb/ocp/deltalake: Implement SMBIOS type 9 -- system slots by SKUMorgan Jang
Create SMBIOS type 9 by getting PCIe config from BMC. TEST=Check SMBIOS type 9 is created correctly on different SKUs Change-Id: Ifd2031b91c960ff2add8807247271eb7c38a0bf2 Signed-off-by: Morgan Jang <Morgan_Jang@wiwynn.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42280 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-23mb/intel/jasperlake_rvp: Enable CSE Firmware Lite SKU for JSLRVPKrishna Prasad Bhat
This patch enables CSE Lite SKU for jasperlake rvp. BUG=b:160201335 BRANCH=None TEST=Build and boot jasperlake rvp with CSE Lite SKU. Cq-Depend: chrome-internal:3142530 Change-Id: I60039ffb1f24cf98f55e83d8c8649745598aa43a Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40571 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-23mb/intel/jasperlake_rvp: Skip CPU Replacement Check for jasperlake rvpKrishna Prasad Bhat
This patch enables the SkipCpuReplacementCheck config for jasperlake rvp to avoid the forced MRC training with the soldered down SOC. BUG=b:160201335 BRANCH=None TEST=Build and verify on jasperlake rvp with CSE Lite SKU. Cq-Depend: chrome-internal:3142530 Change-Id: I40fb9a25170e8db3c63a71428ba459160a918961 Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43146 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-23mb/google/dedede: Enable the CSE Lite SKU for dededeV Sowmya
This patch enables the CSE Lite SKU for the dedede baseboard. BUG=b:160201335 TEST=Build and boot waddledoo with CSE Lite SKU. Cq-Depend: chrome-internal:3142530 Change-Id: I24d7d715d55524807af0127aa4a346a008164b8c Signed-off-by: V Sowmya <v.sowmya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41818 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
2020-07-23mb/google/dedede: Skip the CPU replacement check for dededeV Sowmya
This patches enables the SkipCpuReplacementCheck config for the dedede baseboard to avoid the forced MRC training for all its variants with the soldered down SOC. BUG=b:160201335 TEST=Build and verify CSE Lite SKU on Waddledoo. Cq-Depend: chrome-internal:3142530 Change-Id: I611e66f74a3b9b090ab5e0d836231643d3f919dc Signed-off-by: V Sowmya <v.sowmya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42930 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
2020-07-22mb/google/zork: Modify Woomax variantKane Chen
Update Woomax configuration including GPIO, memory SPD table, I2C devices and USB type C. BUG=b:158343602 BRANCH=None TEST=emerge-zork coreboot Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com> Change-Id: I55ba995d9438551d45cb9e17f92b5089ccf4a5fd Reviewed-on: https://review.coreboot.org/c/coreboot/+/43497 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-07-22mainboard/amd/mandolin: describe where the two HDA codecs resideFelix Held
Change-Id: I99b062e4ce1cf862ea03b0edb6ea843df5f8f2b2 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43359 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-22mb/ocp/deltalake: Unset POWER_STATE_DEFAULT_ON_AFTER_FAILURETim Chu
Change PCH power policy. Set default of POWER_STATE_DEFAULT_ON_AFTER_FAILURE to n in order to change power state to S5 when power is reapplied after power failure. TEST=Base on CB:42289, CB:43338 and build for Deltalake. The following Kconfig options must be selected: select SOC_INTEL_COMMON_BLOCK_PMC select ACPI_INTEL_HARDWARE_SLEEP_VALUES select CPU_INTEL_COMMON_SMM Boot the system and check the last bit of GEN_PMCON_B is set to 1 through ITP with command: pch.pm_dump Signed-off-by: Tim Chu <Tim.Chu@quantatw.com> Change-Id: I4d4f14bdfc18740976171fd5d369b2d79a916dc4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/42976 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Jonathan Zhang <jonzhang@fb.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-22mb/ocp/deltalake: Set FSP log level and add default values if VPD variables ↵Johnny Lin
are not found 1. Read VPD variable 'fsp_log_level' to decide FSP log level. 2. Define the default values when the VPD variables cannot be found, put all the values to vpd.h for better documentation and maintenance. Tested=On OCP DeltaLake, the fsp_log_level can be changed from the VPD variable. Change-Id: I44cd59ed0c942c31aaf95ed0c8ac78eb7d661123 Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43606 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-22mb/google/kukui: revise config structure for Jacuzzi followersHung-Te Lin
There are more Jacuzzi followers coming and we want to have a simplified way of adding new boards. Now, detachable and tablets should select BOARD_GOOGLE_KUKUI_COMMON and clamshells should select BOARD_GOOGLE_JACUZZI_COMMON. BUG=None TEST=make menuconfig; make -j # for kukui, krane, jacuzzi, juniper BRANCH=kukui Change-Id: Ifc1eb6a3792f46c5db6b5346902f1114955b28ae Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43436 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2020-07-21mb/google/dedede: Create madoo variantIan Feng
Create the madoo variant of the waddledoo reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.1.1). BUG=b:161191394 BRANCH=None TEST=util/abuild/abuild -p none -t google/dedede -x -a make sure the build includes GOOGLE_MADOO Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Change-Id: I6d3f611606f86036d67be9c8b0fda833ab61ecc1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43440 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-07-21mb/googlz/zork: Drop unnecessary PULL_UPs in variant overridesFurquan Shaikh
This change drops the pulls configured on override GPIOs as they already have external pull-ups. Also, pads which are unused are configured as PAD_NC. BUG=b:154351731 Change-Id: I8da5d51af25bbe2694c21ecb0868c9cc387243cb Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43562 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-07-21mb/system76/lemp9: drop FSP_M_XIPMichael Niewöhner
Drop FSP_M_XIP since it's selected by the soc already. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I999d369be395de08d4ab7f115fedf4b7fa10eb34 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43635 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jeremy Soller <jeremy@system76.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-07-21mb/system76/lemp9: drop ONBOARD_VGA_IS_PRIMARYMichael Niewöhner
Drop config ONBOARD_VGA_IS_PRIMARY as it's only needed for mainboards with multiple graphics devices. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I6525c65af3dcfc96ea3d68a1388432179e9ac43d Reviewed-on: https://review.coreboot.org/c/coreboot/+/43636 Reviewed-by: Jeremy Soller <jeremy@system76.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-21mb/lenovo/t430/gma-mainboard.ads: Replace with GPLv2+ equivalentPeter Lemenkov
Replace it with t430s/gma-mainboard.ads which is licensed under more flexible terms (GPL-2.0-only vs. GPL-2.0-or-later). Apart from licensing terms these files are identical. This makes diff between boards smaller. Change-Id: I633702d363134654e71e35404237d75b499f089a Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41499 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-07-21mb/lenovo/t420/gma-mainboard.ads: Replace with GPLv2+ equivalentPeter Lemenkov
Replace it with t420s/gma-mainboard.ads which is licensed under more flexible terms (GPL-2.0-only vs. GPL-2.0-or-later). Apart from licensing terms these files are identical. This makes diff between boards smaller. Change-Id: I5393a603b5a4cd353149c1fa9e3e29020946b962 Signed-off-by: Peter Lemenkov <lemenkov@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41498 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-07-21mb/biostar: Add TH61-ITX portMate Kukri
- CPU: only tested with a Xeon E3-1220 (Sandy Bridge) - RAM: native raminit tested (4G+4G, 8G+8G) - USB: both chipset and ASMedia USB3 work, tested in SeaBIOS and Linux (5.4) - LAN: tested in Linux - SATA: all 4 ports work, tested in SeaBIOS and Linux - iGPU: I can't test it as I only have a Xeon for this socket - PEG: tested with an nVidia GT210, initialized by SeaBIOS - PS2 keyboard and mouse combo port: no devices to test with - Front panel header: tested, works - Audio: tested, works - Diagnostic LEDs: TBD Change-Id: I9fd3c0b148b694fcb8e728cc17f0bd45eb5af9f2 Signed-off-by: Mate Kukri <kukri.mate@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43165 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-20google/trogdor: Remove write_protect_stateEric Lai
This is no longer used for chromeos.c. BUG=b:160752610 Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I9a716a88ff9811fff46abca229be15522733bfef Reviewed-on: https://review.coreboot.org/c/coreboot/+/43472 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Bob Moragues <moragues@google.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2020-07-20sb/intel: Define CONFIG_FIXED_SMBUS_IO_BASEAngel Pons
Make it default to 0x400, which is what the touched southbridges use. Change-Id: I95cb1730d5bf6f596ed1ca8e7dba40b6a9e882fe Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43037 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2020-07-20mb/google/dedede: Update link frequency and end point structure for OV9734Pandya, Varshit B
1. Update Link frequency to 180 Mhz 2. Set data-lanes to 1 and 3. Update the clock-lane used by sensor BUG=b:155285666 BRANCH=None TEST=Build and able to capture image using user facing camera. Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com> Change-Id: I164cb6af1003de561be8ce640e7653b7bcb3a22f Reviewed-on: https://review.coreboot.org/c/coreboot/+/42679 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
2020-07-20mb/amd/mandolin: Delete sleep.aslRaul E Rangel
These methods are empty and the kernel treats these as optional. BUG=b:153001807, b:154756391 TEST=none Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: Ic8ee8fb6b6bcd04c653ab77cdc5e746a8cbd0c4a Reviewed-on: https://review.coreboot.org/c/coreboot/+/43466 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-20mb/google/zork: Delete sleep.aslRaul E Rangel
These methods are empty and the kernel treats these as optional. BUG=b:153001807, b:154756391 TEST=Suspend and resume trembyle Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I5f2b375c1186951f95b7ac44dc7158a0299013a1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43465 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-20mb/google/zork: Drop unnecessary PULL_UPs for dalboz referenceFurquan Shaikh
This change drops internal pulls for dalboz reference configured on pads which already have external pull-ups in hardware. GPIO_0(PWR_BTN_L): Pulled up to PP3300_A GPIO_2(WAKE_L): Pulled up to PP3300_A GPIO_10: Unused. Changed to PAD_NC. GPIO_11(EC_IN_RW_OD): Pulled up to PP3300_A GPIO_12(USI_INT_ODL): Pulled up to PP3300_A GPIO_16(USB_OC0_L): Pulled up to PP3300_A GPIO_17(USB_OC1_L): Pulled up to PP3300_A GPIO_21(EMMC_CMD): Pulled up to PP1800_S0 GPIO_22(EC_FCH_SCI_ODL): Pulled up to PP3300_A GPIO_31(EC_AP_INT_ODL): Pulled up to PP1800_A GPIO_32: Unused. Changed to PAD_NC. GPIO_113(I2C2_SCL): Pulled up to PP3300_S0 GPIO_114(I2C2_SDA): Pulled up to PP3300_S0 GPIO_129(KBRST_L): Pulled up to PP1800_S0 GPIO_92(CLK_REQ0_L): Pulled up to PP3300_S0 GPIO_115(CLK_REQ1_L): Pulled up to PP3300_S0 GPIO_116(CLK_REQ2_L): Pulled up to PP3300_S0 BUG=b:154351731 Change-Id: I62e9dbac7a55efa1e055983a7c126168ee516151 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43555 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-20mb/google/zork: Drop unnecessary PULL_UPs for trembyle referenceFurquan Shaikh
This change drops internal pulls for trembyle reference configured on pads which already have external pull-ups in hardware. GPIO_0(PWR_BTN_L): Pulled up to PP3300_A GPIO_2(WAKE_L): Pulled up to PP3300_A GPIO_10: Unused. Changed to PAD_NC. GPIO_12(USI_INT_ODL): Pulled up to PP3300_A GPIO_16(USB_OC0_L): Pulled up to PP3300_A GPIO_17(USB_OC1_L): Pulled up to PP3300_A GPIO_21(EMMC_CMD): Pulled up to PP3300_A GPIO_22(EC_FCH_SCI_ODL): Pulled up to PP3300_A GPIO_31(EC_AP_INT_ODL): Pulled up to PP1800_A GPIO_90: Unused. Changed to PAD_NC. GPIO_113(I2C2_SCL): Pulled up to PP3300_S0 GPIO_114(I2C2_SDA): Pulled up to PP3300_S0 GPIO_129(KBRST_L): Pulled up to PP1800_S0 GPIO_130(EC_IN_RW_OD): Pulled up to PP3300_S0 GPIO_92(CLK_REQ0_L): Pulled up to PP3300_S0 GPIO_115(CLK_REQ1_L): Pulled up to PP3300_S0 GPIO_132(CLK_REQ4_L): Pulled up to PP3300_S0 BUG=b:154351731 Change-Id: Id84b801e019eede7ef543c24aac968f3ef99b3fd Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43526 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-20mb/google/puff: update USB3 gen2 parametersTim Chen
Based on USB3 gen2 SI report to fine tune the parameters for USB3 gen2. BRANCH=none BUG=b:150515720 TEST=build and check the USB3 gen2 register on DUT is correct. Change-Id: I6ec109871d682a1ae2fa4c22fdd6b87ad8a39e9e Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43482 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jamie Chen <jamie.chen@intel.com> Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
2020-07-20mb/asrock/b85m_pro4: Enable VGA portAngel Pons
Now that libgfxinit has been fixed, trying to enable the Analog port no longer hangs the system, nor fills the monitor with unreadable garbage. Tested with linear framebuffer, displays correctly on a 1920x1080 VGA monitor. Scaling also works when a smaller HDMI monitor is connected as well. Legacy VGA text mode is also functional on either monitor, too. Change-Id: Ie2f88edcb7ed1984adebf2af23195767af13654c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43560 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-19mb/qemu-i440fx/memmap: Add warning when falling back to CMOS infosNico Huber
Change-Id: Iefac6fd45791cf6a051450b41046f7e7ebc1dc41 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43446 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-19mb/qemu/fw_cfg: Fix return code check for fw_cfg_e820_select()Nico Huber
Change-Id: I22b9eb6ead37dbba6807d145468843bd01c94c84 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43445 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-19mb/qemu/fw_cfg: Add info messages about (not) found filesNico Huber
Print some more information at BIOS_INFO, like our CBFS code does. Change-Id: I1431d569c57634277ea5cf7feb352419db432b44 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43444 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-18mb/google/dedede: Convert static DPTF ASL into devicetree entriesTim Wawrzynczak
Since there is now a mechanism to generate DPTF ACPI tables and methods at runtime, dedede should switch to using that instead of raw ASL files. This patch converts the existing .asl files into devicetree entries. Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: I6bb6e6e15f50a1e510080e16bbca09dfc5f16b1a Reviewed-on: https://review.coreboot.org/c/coreboot/+/43422 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-18mb/google/volteer: Update DPTF with temp sensor 3Tim Wawrzynczak
While the DPTF refactor was in progress, TSR3 was added to volteer's dptf.asl file, and I forgot to update the devicetree with TSR3 as well. Also missed a swap in the passive policies of TSR0 and TSR1. This patch fixes those. BUG=b:149722146 TEST=boot volteer, dump SSDT & DSDT, verify TSR3._STA returns 0xF Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: I71bc798492ec45bb1e2f8d779e6829db52ef4499 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43528 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Caveh Jalali <caveh@chromium.org>
2020-07-17mb/google/zork/var/vilboz: Use AMDI1015 HID for I2S machine deviceFurquan Shaikh
Vilboz requires a different HID than rest of the zork variants. Hence, this change sets the HID to AMDI1015 for I2S machine device in vilboz overridetree.cb. BUG=b:157708581 Change-Id: Ibae343f21cf8f0c782dc8a461f69172bf0da7eba Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43545 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-17mb/google/zork: Switch to using newly added i2s_machine_dev driverFurquan Shaikh
This change switches zork devices to use the newly added i2s_machine_dev driver in devicetree rather than passing dmic_select_gpio in SoC config. BUG=b:157708581 Change-Id: I76c633694cbfb454c081ab2a4af4765bfbbae16b Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43543 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-07-17mb/asrock/b85m_pro4: Select MAINBOARD_USES_IFD_GBE_REGIONAngel Pons
This board uses the in-PCH GbE controller, and its IFD has a GbE region. Change-Id: Ifc09640b2ebd613d3d5566a13b50d36c11e3c346 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43522 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-17mb/amd/mandolin: Drop mainboard.aslFurquan Shaikh
This change drops mainboard.asl from zork because none of the objects defined in it are used. Change-Id: I879b5614fb5d12c4814ee52f840a000744a7aab9 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43520 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-17mb/google/zork: Drop mainboard.aslFurquan Shaikh
This change drops mainboard.asl from zork because none of the objects defined in it are used. BUG=b:153879530 Change-Id: If5440bcbce39b4461b44acaec69561663b1ea329 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43519 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-17soc/amd/picasso: Move PMOD global variable to globalnvs.aslFurquan Shaikh
Global variable `PMOD` that stores the interrupt mode used by OS is required by all mainboards. This change moves the variable definition to globalnvs.asl under picasso. Additionally, ACPI spec says that BIOS should assume interrupt mode as PIC until _PIC() method is called by OS. Thus, this change also updates the default value of PMOD as 0 i.e. PIC mode. BUG=b:153879530 Signed-off-by: Furquan Shaikh <furquan@google.com> Change-Id: I731c03d965882281a7a23f55894451210ba72274 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43514 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-17mb/google/zork: correct wake gpe value for gpio 9Aaron Durbin
GPIO_9 is associated with gevent 22. Correct all the misconfigurations and use macros for clarity as to what bit offset is being used instead of open coding things. BUG=b:161205804 Change-Id: Ic4cfd62763d72d12a55f89585f24e07df6af0f4f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43516 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-17mb/google/zork: Enable ACP_PME_EN and ACP_I2S_WAKE_ENFurquan Shaikh
This change enables ACP_PME_EN and ACP_I2S_WAKE_EN for dalboz and trembyle boards using devicetree settings. BUG=b:161328042,b:146317284 Change-Id: Ie367a9ba878a1892177df874bbcb8005efeb0880 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43496 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-16soc/amd/picasso: remove unused fadt_pm_profile devicetree settingFelix Held
commit 56da63c3dc3f50cfac541c779b608e1bae9e635c removed overriding that field in the FADT. Change-Id: I0c8ff9ab125129dc856949c47a3a0c14e4109c73 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43417 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-16mb/amd/mandolin: add SATA DXIO descriptor for Dali SKUsFelix Held
Dali supports two SATA ports, but no PCIe alternate function on those pins. Change-Id: I27a13100e80565eb1dade2d703ba3d1f8b5f630f Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43493 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-16mb/amd/mandolin: fix DXIO lane numbersFelix Held
The DXIO descriptors use the logical and not the physical lane numbers, which are different. Change-Id: I7a90056d782d8d32fe34a0f5bdb61c3b61df1af8 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43492 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-16soc/amd/picasso/acpi,mb/{zork,mandolin}: Stop clearing PciExpWakeStatusRaul E Rangel
The kernel already clears this: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/master:src/third_party/kernel/v5.4/drivers/acpi/acpica/hwregs.c;l=390 No reason to have the firmware do it as well. BUG=b:153001807, b:154756391 TEST=Build Trembyle, boot, suspend, and resume and didn't see any ACPI errors. Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: Ia5c79fb95dc885eaef8abc4257b6ba18c1ef1b66 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43428 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-07-16soc/amd/picasso,mb/{zork,mandolin}: Remove invalid UPWS variableRaul E Rangel
PMx0EE is not defined in the Picasso PPR. BUG=b:153001807, b:154756391 TEST=None Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I98caf0cd2d0bdcf19de2b945dcf74f5cf7354769 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43424 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-07-16mb/amd/mandolin/.../sleep.asl: Remove unnecessary variableRaul E Rangel
There is no reason to create a named variable. We can just return the package. BUG=b:153001807, b:154756391 TEST=None Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: Ic0ca2e6d4fb833c68d29e9948a670ace7c89b6a5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/43464 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-11 18:52:18 +0000