summaryrefslogtreecommitdiff
path: root/src/mainboard/google
AgeCommit message (Collapse)Author
2017-03-09google/pyro: Update DPTF settingsKevin Chiu
1. Update DPTF TSR1 passive trigger points. TSR1 passive point: 50 2. Update DPTF PL1 Minimum PL1 min: 2.5W BUG=b:35586881 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: Ia2634f40098d026c4d228fab4b7c05501c1ff05f Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18699 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-09mainboard/google/poppy: Enable cros_ec_keyb deviceFurquan Shaikh
This is required to transmit button information from EC to kernel. BUG=b:35774934 BRANCH=None TEST=Verified using evtest that kernel is able to get button press/release information from EC. Change-Id: I8f380f935c2945de9d8e72eafc877562987d02db Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18642 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-03-08mainboard/google/poppy: Add EC_HOST_EVENT_MODE_CHANGE to wakeup sourceFurquan Shaikh
Allow EC mode change event to wake AP up in S3. BUG=b:35775085 BRANCH=None TEST=Compiles successfully for poppy. Change-Id: I6f1546c60aef6620e22cdce2fab3a2709e6556a1 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18608 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-08google/eve: Configure GPIOs for new boardDuncan Laurie
A new board revision is making use of two previously unused GPIOs to drive BOOT/RESET pins to an on-board MCU. The reset pin is open drain so it is set as input by default, and the boot pin is driven low by default. Since these are UART0 pins they also need to be set up again after executing FSP-S as it will change them back to native mode pins. BUG=b:36025702 BRANCH=none TEST=manual testing on reworked board, toggling GPIOs to put the MCU into programming mode. Change-Id: Id6f0ef2f863bc1e873b58e344446038786b59d25 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18661 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-03-08mainboard/google/snappy: Override USB2 phy settingWisley Chen
Fine tune USB2, need to override the following registers. port#1: PERPORTPETXISET=7 PERPORTTXISET=0 BUG=b:35858164 BRANCH=reef TEST=built, measured eye diagram on snappy, and reviewed by intel Change-Id: I461cf8f032b4e70abc9707e6cd3603a62cee448f Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18590 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-07google/gru: add MAX_SDRAM_FREQ config to choose max ddr freqShunqian Zheng
Gru/Kevin use 933 MHz (actually 928 MHz for better jitter) as max sdram frequency, while bob uses 800 MHz. It's normal some variants can't meet 928 MHz SI requirement and hence have to use a lower freq as spec. BUG=chrome-os-partner:61001 BRANCH=gru TEST=check dpll is 800 MHz on bob Change-Id: I6d19a351f25d1f48547715ce57c3a87d9505f6f1 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 8176bfea52422c713f144ffec419752aeca66db2 Original-Change-Id: I46afba8d091f1489feeb20cafc44decaa81601fc Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/420208 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Commit-Queue: Shasha Zhao <Sarah_Zhao@asus.com> Original-Tested-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-(cherry picked from commit eba5dff79eeedae5ff608d2d8d297ccf9c13cb55) Original-Reviewed-on: https://chromium-review.googlesource.com/448277 Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org> Reviewed-on: https://review.coreboot.org/18581 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-03-07google/veyron: add K4B4G1646E-BYK0 ddr with ramid 000ZShunqian Zheng
The K4B4G1646E-BYK0 shares sdram config with K4B4G1646D-BYK0. For clarity, sdram-ddr3-samsung-2GB now is used by - K4B4G1646D-BYK0 - K4B4G1646E-BYK0 - K4B4G1646Q-HYK0 BUG=chrome-os-partner:62131 BRANCH=veyron TEST=emerge Change-Id: Ie43f23bf8f5f5b1acbb74c85cac17fe181c841c4 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 46d62d87101e0ee1050b00db02b3ecaa4587e9f4 Original-Change-Id: I461c6f36c28ea0eeaf7d64292c9c87ab0c9de443 Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/446197 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-(cherry picked from commit f98251a4a4fe4d49721a936a684f6ac80f3f6405) Original-Reviewed-on: https://chromium-review.googlesource.com/446300 Reviewed-on: https://review.coreboot.org/18519 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-03-07google/veyron_*: Add new Micron and Hynix modulesDavid Hendricks
This adds SDRAM entries for the following modules: - Micron: DDMT52L256M64D2PP-107 - Hynix: H9CCNNNBKTALBR-NUD They are compatible with Samsung K4E8E324EB-EGCF, so this just copies sdram-lpddr3-samsung-2GB-24EB.inc and changes the name used in the comment near the top. Notes on our "special snowflake" boards: - veyron_danger's RAM ID is hard-coded to zero, so I skipped changes involving the binary first numbering scheme. - Rialto's SDRAM mapping is different, so I padded its SDRAM entries to 24 to match other boards. - veyron_mickey requires different MR3 and ODT settings than other boards due to its unique PCB (chrome-os-partner:43626). BUG=chrome-os-partner:59997 BRANCH=none TEST=Booted new modules on Mickey (see BUG) Change-Id: If2e22c83f4a08743f12bbc49b3fabcbf1d7d07dd Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 35cac483e86e57899dbb0898dad3510f4c2ab2d3 Original-Change-Id: I22386a25b965a4b96194d053b97e3269dbdea8c7 Original-Signed-off-by: David Hendricks <dhendrix@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/412328 Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Original-Commit-Queue: Jiazi Yang <Tomato_Yang@asus.com> Original-Tested-by: Jiazi Yang <Tomato_Yang@asus.com> Original-(cherry picked from commit bd5aa1a5488b99f2edc3e79951064a1f824062f6) Original-Reviewed-on: https://chromium-review.googlesource.com/446299 Original-Commit-Ready: Shunqian Zheng <zhengsq@rock-chips.com> Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18518 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-03-07google/poppy: fix finger print sensor interrupt gpio configurationRizwan Qureshi
Configure the right GPIOs for finger print sensor interrupt and reset lines. As per the schematics GPP_C8 is for sensor interrupt and GPP_C9 is for sensor reset. Change-Id: Ib25c68ec2fe20b1302b6170d67ceab7e8cca1a83 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18389 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-02mainboard/google/poppy: Disable deep S3 on poppyFurquan Shaikh
BUG=chrome-os-partner:62963 BRANCH=None TEST=Compiles successfully Change-Id: Icb929262fd67362b8e5c5cf31dce04ab1f496695 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18467 Tested-by: build bot (Jenkins) Reviewed-by: Rajat Jain <rajatja@google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-25mainboard/google/reef: keep LPSS_UART2_TXD high in suspend stateAaron Durbin
The cr50 part on reef is connected to the SoC's UART lines. However, when the tx signal is low it causes an interrupt to fire on cr50. Therefore, keep the tx signal high in suspend state so that it doesn't cause an interrupt storm on cr50 which prevents cr50 from sleeping. BUG=chrome-os-partner:63283 BRANCH=reef TEST=s0ix no longer causes interrupt storm on cr50. Power consumption normal. Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18491 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-25google/eve: Add rise/fall times for I2C busesDuncan Laurie
Apply tuning for the PCH I2C buses on Eve based on rise/fall time measurements that were done with a scope. BUG=chrome-os-partner:59686 BRANCH=none TEST=Manual testing on Eve P1 to verify that all devices on I2C buses are still functional. Post-tuning measurement will be done once a new firmware is released. Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18487 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-24mainboard/google/poppy: Change touchscreen IRQ to level-triggeredFurquan Shaikh
BUG=chrome-os-partner:62967 BRANCH=None TEST=Verified that touchscreen works on power-on and after suspend-resume as well. Change-Id: Id674cbcc2d524a6ed2883bf9f0e9e076890f9a85 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18466 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-23google/gru: whitespace fixPatrick Georgi
Follow up to https://review.coreboot.org/#/c/18460/ Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18475 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: Tuning USB 2.0 PHY0 and PHY1 squelch detection thresholdWilliam wu
According to USB 2.0 Spec Table 7-7, the High-speed squelch detection threshold Min 100mV and Max 150mV, and we set USB 2.0 PHY0 and PHY1 squelch detection threshold to 150mV by default, so if the amplitude of differential voltage envelope is < 150 mV, the USB 2.0 PHYs envelope detector will indicate it as squelch. On Kevin board, if we connect usb device with Samsung U2 cable, we can see that the impedance of U2 cable is too big according to the eye-diagram test report, and this cause serious signal attenuation at the end of receiver, the amplitude of differential voltage falls below 150mV. This patch aims to reduce the PHY0 and PHY1 otg-ports squelch detection threshold to 125mV (host-ports still use 150mV by default), this is helpful to increase USB 2.0 PHY compatibility. BRANCH=gru BUG=chrome-os-partner:62320 TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into Type-C port, check if the USB device can be detected. Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8 Original-Signed-off-by: William wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/431015 Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com> Original-Tested-by: Inno Park <ih.yoo.park@samsung.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18462 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2017-02-23google/gru: update the pwm regulatorCaesar Wang
As David commented the "Bob and other follow-ons match Gru, Kevin should be the special case here", and update the calculations value for gru/bob board. From the actual tests, some regulator voltage than the actual set of less than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the {min, max} regulator voltage for Bob board. Make sure we get the accurate voltage. BUG=chrome-os-partner:61497 BRANCH=none TEST=boot up Bob, measure the voltage for little cpu and C-logic. Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4 Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/424523 Original-Reviewed-by: David Schneider <dnschneid@chromium.org> Original-Reviewed-by: Brian Norris <briannorris@chromium.org> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430403 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18460 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23mb/google/poppy: Enable support for DPTFSumeet Pawnikar
This patch adds the DPTF settings specfic to the mainboard and enables the CPU and other thermal sensors as participant device for poppy. It enables the DPTF flag in the device tree for poppy. It also includes the DPTF specific ASL file in the main DSDT definition. BUG=None BRANCH=None TEST=Built for poppy. Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36 Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/17926 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-23google/oak: Add initial support for RowanYidi Lin
Update GPIO controls and mainboard configurations for Rowan. [pg: use the opportunity to clean-up the gerrit-rebase task list with the entirely unrelated Ignore-CL-Reviewed-on lines] BUG=chrome-os-partner:62672 BRANCH=none TEST=emerge-rowan coreboot Change-Id: I110fb368b3d9fa9dfb2bf091342dfb511ff7c09c Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: f4252cbe94a7456108aaa522e170bca5dcb1fdd1 Original-Change-Id: I18ebc3ccf4c7d051839d7c50e9b0682ef8f09830 Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430557 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/341513 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/327003 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/355221 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/354670 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361360 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361361 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361362 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361363 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/382320 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405110 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405130 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/419795 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/424139 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430293 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430294 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430295 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427820 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427821 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427822 Reviewed-on: https://review.coreboot.org/18463 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: improve eye diagram for passing the testCaesar Wang
The children of Gru should share the benefits. In the real world, Bob can't pass the eye diagram tests. BUG=chrome-os-partner:62714 BRANCH=firmware-gru-8785.B TEST=build coreboot Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/440745 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/441468 Reviewed-on: https://review.coreboot.org/18461 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22acpi: Add ACPI_ prefix to IRQ enum and struct namesFurquan Shaikh
This is done to avoid any conflicts with same IRQ enums defined by other drivers. BUG=None BRANCH=None TEST=Compiles successfully Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18444 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-22google/gru: Fix whitespacePatrick Georgi
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18322 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Enable Realtek 5663 supportRizwan Qureshi
Enable Realtek RT5663 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=With required driver support in kernel verify audio on headset Change-Id: I9b9eb1e7edca56870f5be0e4fd603c9b0dc7f9de Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18216 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Enable Maxim MAX98927 codecRizwan Qureshi
Enable Maxim 98927 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=with required driver support in kernel verify audio on poppy on-board speakers. Change-Id: Id731de42d77204d59f32ac4c33a245837d6e2107 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Dylan Reid <dgreid@chromium.org> Reviewed-on: https://review.coreboot.org/18215 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Generate required nhlt tableRizwan Qureshi
poppy board uses Maxim 98927 speaker codec and Realtek RT5663 for headset. Select the apropriate NHLT blobs to be packaged in CBFS. Also, generate the required ACPI NHLT table for codec and the supported topology in poppy. BUG=chrome-os-partner:62051 BRANCH=None TEST=With the required driver support in kernel verify that the Audio plays on on-board speakers and headset, recording works from on-board mics and headset mics. Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed Signed-off-by: M Naveen <naveen.m@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/18214 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20drivers/i2c: Use I2C HID driver for wacom devicesFurquan Shaikh
Wacom I2C driver does the same thing as I2C HID driver, other than defining macros for Wacom HID. Instead of maintaining two separate drivers providing the same functionality, update all wacom devices to use generic I2C HID driver. BUG=None BRANCH=None TEST=Verified that ACPI nodes for wacom devices are unchanged. Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18401 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20google/eve: Set touchscreen I2C bus speed to 1MHzDuncan Laurie
Enable Fast-Plus speed for the touchscreen device so it can be used at 1MHz instead of 400KHz. BUG=chrome-os-partner:61277 TEST=manual testing on Eve P1, needs backported kernel patches to actually make use of any I2C speed other than 400KHz Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18397 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-20google/eve: Add audio devicesDuncan Laurie
Add the audio devices to Eve mainboard: - Describe Maxim 98927 speaker amps and RT5663 headphone codec in ACPI so they can be enumerated by the OS. - Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH. BUG=chrome-os-partner:61009 TEST=manual testing on Eve P1 with updated kernel to ensure that both speakers and headset are functional. DMIC support is is still being worked on and is not yet functional. Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18398 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-02-20mainboard/{google,intel}: Change config option selectionFurquan Shaikh
Change config option selection from "config xyz default y" to "select xyz" if the config option has no dependencies. BUG=None BRANCH=None TEST=Verified that config option selection remains unchanged. Change-Id: I259ae40623b7f4d5589e2caa0988419ba4fefda4 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18400 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20mainboard/google/reef: Remove config DRIVERS_GENERIC_GPIO_REGULATORFurquan Shaikh
Since we are not using gpio regulators on reef anymore, remove the selection from Kconfig as well. BUG=None BRANCH=None TEST=Compiles successfully. Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18399 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20google/slippy: consolidate variants' common mainboard.asl codeMatt DeVillier
Move code common code from each variant's mainboard.asl into common ACPI code for all variants (like google/auron). This also adds the _PRW method for the LID0 device for falco and peppy, which omitted the function when they were originally upstreamed. See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18368 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-20google/eve: Set rise/fall timing values for I2C bus 1Duncan Laurie
Apply the measured rise and fall times for I2C bus 1 on Eve so it can be tuned properly for 400KHz operation. BUG=chrome-os-partner:63020 TEST=verify I2C1 bus speed with a scope Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18396 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-20google/eve: Fix FPC supportDuncan Laurie
Currently UART0 GPIOs are being put into native mode during FSP-S stage, so have ramstage re-configure them back to regular GPIO mode. GPP_C8 does not seem to be functioning properly when routed to the APIC, possibly due to the UART0 being enabled even though it is unused, which is required because UART0 is PCI 1e.0 and so must be present for other 1e.x functions to be enumerated. Instead, use this pin as a GPIO interrupt so it will be routed through the GPIO controller at IRQ 14. GPP_C9 was inverted and was only working because the pin was being re-configured in FSP-S. Also export the reset gpio as a device property so it can be used by the kernel driver, which will stop it from complaining at boot. BUG=chrome-os-partner:61233 TEST=verify that the interrupt and device is functional in the OS Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18395 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/eve: select SOC_INTEL_KABYLAKERizwan Qureshi
eve is based on Kabylake SoC hence select the appropriate config. Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18314 Tested-by: build bot (Jenkins) Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/poppy: select SOC_INTEL_KABYLAKERizwan Qureshi
poppy is based on Kabylake SoC hence select the appropriate config. Change-Id: Ie339a3991eeccb8a7dba983a2b5ab5d1c996ce9d Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18313 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/google/poppy: Generate digitizer node in SSDTFurquan Shaikh
Add support for generating digitizer node in SSDT using wacom i2c driver. BUG=None BRANCH=None TEST=Verified that the node shows up in SSDT. Change-Id: If7e1e2463778c2ff7263eff995def149457edcde Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18373 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-16mainboard/google/eve: Generate FPC device using SPI SSDT generatorFurquan Shaikh
Use the newly added SPI SSDT generator for adding FPC device. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully. Verified that the SSDT entry matches the entry in mainboard.asl Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18343 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-15mainboard/google/reef: add sand variantYH Lin
Create the initial Sand variant which refers to the Reef. Sand is APL board that derives from reference board Reef. BRANCH=master BUG=chrome-os-partner:62200 TEST=Build (as initial setup) Signed-off-by: YH Lin <yueherngl@chromium.org> Change-Id: Iba8c5653b6176676c759d2b48063f0c0c6cde625 Reviewed-on: https://review.coreboot.org/18324 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-14google/eve: change touchpad HIDWei-Ning Huang
Change touchpad HID to use with the Google Centroiding Touchpad driver. BUG=chrome-os-partner:61088 TEST=`emerge-eve coreboot` Change-Id: I199ff46f1a93d3eccc8c694742585dcf37b2373f Signed-off-by: Wei-Ning Huang <wnhuang@google.com> Reviewed-on: https://review.coreboot.org/18359 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-14google/rambi: add explicit pull-down for ram-idMatt DeVillier
Some variants need the internal pull resistor on GPIO_SSUS_40 set explicitly to pull down rather than disabling the pull, in order for the ram-id to be read correctly via GPIO. Correct this by adding a function to enable and set the internal pull and define its use as needed in the board's variant.h. Chromium source: branch: firmware-gnawty-5216.239.B /src/soc/intel/baytrail/baytrail/gpio.h#418 /src/mainboard/google/gnawty/romstage.c#60 Test: boot 4GB Candy board and observe correct RAM id, amount detected Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18309 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-14google/poppy: select NO_FADT_8042Jenny TC
Poppy doesn't support 8042 keyboard. Select NO_FADT_8042 to disable 8042 in FADT header. Kernel will not try to access 8042 region if 8042.FADT=0 BUG=chrome-os-partner:61858 TEST=Boot OS and verify FADT 8042 flag Change-Id: I00182eb4b059d4d9f0705d349dc98651e3955f0d Signed-off-by: Jenny TC <jenny.tc@intel.com> Reviewed-on: https://review.coreboot.org/18311 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-13mainboard/google/snappy: Update DPTF settingsWisley Chen
Update DPTF parameters based on thermal team test result. 1. Update TSR2 trigger points. TSR2 passive point: 70, critical point: 90 2. Set PL2 Max to 15W. BUG=chrome-os-partner:61383 BRANCH=reef TEST=build, boot on snappy, and verified by thermal team Change-Id: I8d01d6c1d7eabd359ceb131f3cd10965d4ac2c42 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18318 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-11mainboard/google/reef: Increase PL1 sampling periodSumeet Pawnikar
Performance degradation seen with current PL1 throttling rate as 8 seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1 throttling rate to 15 seconds, fps score improved. BUG=chrome-os-partner:60038 BRANCH=reef TEST=Built and tested on electro system Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/18317 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
2017-02-11google/gru: add scarlet variantphilipchen
There will be more follow-up changes. BUG=chrome-os-partner:62377 BRANCH=None TEST=emerge-scarlet coreboot libpayload Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a Original-Signed-off-by: philipchen <philipchen@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/433039 Original-Commit-Ready: Philip Chen <philipchen@chromium.org> Original-Tested-by: Philip Chen <philipchen@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18296 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2017-02-07mainboards/google/reef: Add support for tablet mode switch.Gwendal Grignou
Reef is a convertible add support for sending Tablet mode switch changes from EC to AP. Change-Id: I6dfddbfdb5a2ffbdfd77c5f49602bf68e9693a06 Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/18277 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-07google/eve: Add support for tablet mode switch.Gwendal Grignou
Eve is a convertible add support for sending Tablet mode switch changes from EC to AP. Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/18276 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-05google/eve: Fix keyboard backlight enable in wake from G3Duncan Laurie
The WAK_STS bit is not set in a wake from G3, so the check for this bit needs to only be done when checking for a wake from S3. This change correctly enables the keyboard backlight in wake from G3 and only does not enable it during a wake from S3. BUG=chrome-os-partner:58666 TEST=Use Refresh+Power to issue hard reset and ensure that the keyboard backlight turns on like it does when waking from S5. Also force enter hibernate with Alt+VolumeUp+H and then power back up and ensure that the keyboard backlight is enabled when booting. Change-Id: I44045950e38aa5e5ae96a79385d604791852c7e6 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18280 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-04google/jecht: Fix LED for guado/rikku variantsMatt DeVillier
When guado/rikku/tidus were rolled into jecht, an error was made in set_power_led() as guado/rikku set the polarity differently than tidus. Fix the power LED for guado/rikku by setting the polarity correctly. Test: boot guado/rikku and observe proper function of power LED under S0, S3, and S5 power states. Change-Id: I23072ac60bc9683776f748ca1326d98257c3c54f Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18249 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-04Revert "google/pyro: remove Wacom touchscreen probed flag"Kevin Chiu
Reason for revert: Pyro has two touchscreen sources: WACOM/ELAN. It will not have both touchscreen IC in one system at the same time. So the "probed" property of WACOM i2c device is mandatory to set for kernel to know whether it exists before driver initializes it. Otherwise in ELAN case, when driver fails to init WACOM i2c device, ACPI _OFF will be invoked to set GPIO#152 low to cut off power. BUG=chrome-os-partner:62371 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I30f467bd8720d959686dc14f7877e6bc11ea6213 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18291 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-04google/eve: Fix DRAM DQS mapDuncan Laurie
This change fixes the two sets of pins that were swapped in the map of DQS signals from CPU to DRAM for channel 1. Although this does not appear to have any impact to the system it does result in different register values for DQS pin mapping that are programmed inside FSP. BUG=chrome-os-partner:58666 TEST=This fix was verified against the current schematic and using FSP debug output. Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18279 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-04google/poppy: Set GPIO GPP_D22 highRizwan Qureshi
same change as I49935e659bf67225d3f5db1b06acc2cd046dcd74 this is required for poppy board as well. GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals when doing GPIO-driven I2S. This needs to be high by default so the DSP can drive these signals, instead of low where it is enabled for GPIO-driven I2S and the DSP cannot drive these signals. BUG=None BRANCH=None TEST=play test sound in OS over internal speaker Change-Id: I1695e9198f8f78e9c5ad6df6c1ac073ac1762c6b Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18282 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-04google/eve: Set GPIO GPP_D22 highDuncan Laurie
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals when doing GPIO-driven I2S. This needs to be high by default so the DSP can drive these signals, instead of low where it is enabled for GPIO-driven I2S and the DSP cannot drive these signals. BUG=chrome-os-partner:58666 TEST=play test sound in OS over internal speaker Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18281 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-03mainboard/google/snappy: Set PL2 override to 15000mWHarry Pan
This patch sets PL2 override value to 15W in RAPL registers. BUG=chrome-os-partner:62110 BRANCH=reef TEST=Apply new firmware to evaluate Octane benchmark score. Change-Id: I51734051586753677129314b5273fb275c74f5d2 Signed-off-by: Harry Pan <harry.pan@intel.com> Reviewed-on: https://review.coreboot.org/18283 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-02-01Add Baytrail ChromeOS devices using variant schemeMatt DeVillier
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty, heli, kip, orco, quawks, squawks, sumo, swanky, and winky using their common reference board (rambi) as a base. Chromium sources used: firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...] firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...] firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...] firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...] firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...] firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...] firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*] firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.] firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data] firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data] firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...] firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table] firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...] The same basic cleanup/changes are made here as with the initial BYT variant commit: - remove unused ACPI trackpad/touchscreen devices - correct I2C addresses in SMBIOS entries - clean up comment formatting - remove ACPI device for unused light sensor - switch I2C ACPI devices from edge to level triggered interrupts, for better compatibility/functionality (and to be consistent with other recently-upstreamed ChromeOS devices) - Micron 2GB SPD file for kip with updated values renamed to distinguish from same file used by other boards Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18164 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-31google/veyron*: mark GPIO array non-staticPatrick Georgi
That status isn't needed and making it non-static helps gcc 4.9.2 (or any compiler that insists on "standard C" behaviour with global const initializers) Change-Id: Ib1fbd5213d262e653f31564b106095b4a28292f6 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/18266 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-31mainboard/google/reef: remove NHLT DMIC 1ch and 2ch configurationSathyanarayana Nujella
Apollolake boards should use DMIC-4ch configuration in Kernel side and use CaptureChannelMap in userspace to distinguish boards with different number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will not be required and hence removed. BUG=chrome-os-partner:60827 TEST=Verify internal mic capture TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/18252 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-31mainboard/google/reef: Set edge triggered interrupt for GPIO_22Vaibhav Shankar
EC sets the logic level based on outstanding wake events. When GPIO_22 is configured as a level triggered interrupt, the events are not cleared from the interrupt handler. Hence, we'd just be re-signalling over and over causing an interrupt storm upon lid open. So, GPIO_22 needs to be configured as EDGE_SINGLE instead of LEVEL. BUG=chrome-os-partner:62458 TEST=Lid close/open. check CPU usage using top. It should not show 70% CPU usage. Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a Reviewed-on: https://review.coreboot.org/18267 Tested-by: build bot (Jenkins) Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-29mainboard/google/snappy: Update WDT touchscreen deviceFurquan Shaikh
Export PowerResource for WDT touchscreen device. BUG=chrome-os-partner:62311, chrome-os-partner:60194, chrome-os-partner:62371 BRANCH=reef TEST=Compiles successfully. Change-Id: Icc5be170353753201d3571c39b50e29424d4d6d3 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18240 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-29mainboard/google/pryo: Update touchscreen device ACPI nodesFurquan Shaikh
1. For ELAN, export reset GPIO as well as PowerResource 2. For WCOM, export PowerResource BUG=chrome-os-partner:62311, chrome-os-partner:60194, chrome-os-partner:62371 BRANCH=reef TEST=Verified that touchscreen works on pyro with WCOM device on power-on as well as after suspend/resume. Change-Id: I0306e24e19bf821cd3e08fdacc0d78b494c9a92f Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18239 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-29i2c/generic: Allow GPIOs to be put in _CRS and PowerResource in ACPIFurquan Shaikh
Linux kernel expects that power management with ACPI should always be handled using PowerResource. However, some kernel drivers (e.g. ELAN touchscreen) check to see if reset gpio is passed in by the BIOS to decide whether the device loses power in suspend. Thus, until the kernel has a better way for drivers to query if device lost power in suspend, we need to allow passing in of GPIOs via _CRS as well as exporting PowerResource to control power to the device. Update mainboards to export reset GPIO as well as PowerResource for ELAN touchscreen device. BUG=chrome-os-partner:62311,chrome-os-partner:60194 BRANCH=reef TEST=Verified that touchscreen works on power-on as well as after suspend-resume. Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18238 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-01-29mainboard/google/reef: Set IOSSTATE for trackpad I2C GPIOsVaibhav Shankar
I2C data (GPIO_132) and Clk (GPIO_133) lines are pulled low during standby states S3/S0ix. This causes leakage of power. To reduce the leakage, we have to pull these lines high during S3/S0ix. This is done by programming the IOSSTATE to HIz. Also note that we are using the internal pull ups to keep at SOC at 1.8V and the I2C lines are not floating. BUG=chrome-os-partner:62428,chrome-os-partner:61651 TEST=Enter S3/S0ix. Measure trackpad power. It should be less than 4mW. Also I2c lines should be pulled high in S3/S0ix. Change-Id: I5570ac37ec3cc41f6463dd6b858fdb56a20a1733 Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/18251 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-01-26google/pyro: Add USB2 phy setting overrideKevin Chiu
In order to pass type A USB2 eye diagram, USB2 port#0/#1 PHY register will need to be overridden. port#0: PERPORTPETXISET = 7 PERPORTTXISET = 1 IUSBTXEMPHASISEN = 3 PERPORTTXPEHALF = 0 port#1: PERPORTPETXISET = 7 PERPORTTXISET = 2 IUSBTXEMPHASISEN = 3 PERPORTTXPEHALF = 0 BUG=chrome-os-partner:59491 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I8e67a6f0192d1c0abf6ec4926c2a17e44c818948 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18229 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-26google/pyro: Disable Wacom touchscreen probedKevin Chiu
Wacom touchscreen is i2c hid device and it's the device that always exists. So no need to set "probed" property for it. BUG=chrome-os-partner:61513 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I27fe18ceadd03029b826e0237f80132eda1089b0 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18227 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-25google/pyro: Modify Wacom touchscreen IRQ type to level-triggeredKevin Chiu
Follow i2c-hid spec definition, level trigger interrupt is required for i2c-hid device. BUG=chrome-os-partner:61513 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: Ia825bd0c898e71e2ee2bf411f117a49a8fb411b6 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18217 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-24google/eve: Enable PD MCU deviceDuncan Laurie
In order for PD charge events to properly notify the OS when a charger is attached we need to enable the PD MCU device and event source from the EC. Without this change the charging still happens, but the OS does not notice and update the charge state icon in the Chrome OS UI. BUG=chrome-os-partner:62206 BRANCH=none TEST=plug in a charger to either port and see charge status updated to indicate charging in the power_supply_info tool and the Chrome OS UI. Change-Id: Ia6f63ac719b739326d313f657a68005c32f45b8d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18209 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-23google/pyro: Update DPTF settingsKevin Chiu
1. Update DPTF CPU/TSR1 passive trigger points. CPU passive point: 80 TSR1 passive point: 46 2. Update DPTF TRT Sample Period TSR1: 8s BUG=chrome-os-partner:62133 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I8fcf750ac17b8894ed3c8704eec62f5071d9cf24 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18174 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-22gru: kevin: define GPIOs used on both platformsVadim Bendebury
The same GPIOs are used on both platforms, definitions are added an a new .h to make it easier to re-use them across the code. BRANCH=none BUG=chrome-os-partner:51537 TEST=panel backlight still enabled on Gru as before. The rest of the GPIOs are used in the upcoming patches. Change-Id: I54ef3e8dd79670bdb037baeec91430113d11bcc1 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: c58788026f28af52c650da0159b93d97269ca4a9 Original-Change-Id: I1a6c5b5beb82ffcc5fea397e8e9ec2f183f4a7e0 Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/346219 Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com> Reviewed-on: https://review.coreboot.org/18176 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-22mainboard/google/reef: Increase TSR1 trigger pointTim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_EVT2_v0.4_20170120.xlsx) 1. Update DPTF TSR1 passive trigger point. TSR1 passive point: 46 BUG=chrome-os-partner:60038 BRANCH=master TEST=build and boot on electro dut Change-Id: If35e4cf2dbf7c506534c52a052598f6204d5315a Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18183 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-22google/eve: Fixes for devicetree settingsDuncan Laurie
The devicetree settings were incorrect in a few places with respect to the SOC and board design: - IMVP8 VR workaround is for MP2939 and not MP2949 on Eve - IccMax values are incorrect according to KBL-Y EDS - USB2[6] is incorrectly labeled - I2C touch devices do not need probed as they are not optional - PCIe Root Port 5 should be enabled - I2C5 device should not be enabled as it is unused BUG=chrome-os-partner:58666 TEST=manually tested on Eve board Change-Id: I74e092444ead4b40c6d8091b80a691d44e2c6c7d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18200 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-22google/eve: Enable separate recovery MRC cacheDuncan Laurie
In order to get quick boot speeds into recovery enable the feature that allows for a separate recovery MRC cache. This requires shuffling the FMAP around a bit in order to provide another region for the recovery MRC cache. To make that shuffling easier, group the RW components into another sub-region so it can use relative addresses. BUG=chrome-os-partner:58666 TEST=manual testing on eve: check that recovery uses the MRC cache, and that normal mode does too. Check that if cache is retrained in recovery mode it is also retrained in normal mode. Also check that events show up in the log when retrain happens. Change-Id: I6a9507eb0b919b3af2752e2499904cc62509c06a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18199 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-22google/eve: Enable keyboard backlight in bootblockDuncan Laurie
Enable the keyboard backlight as early in boot as possible to provide a indication that the BIOS is executing. Since this is bootblock it can't use the convenience function for checking for S3 resume so just read the PM1 value from the SOC and check it directly. Use a value of 75% for the current system as that is visible without being full brightness. BUG=chrome-os-partner:61464 TEST=boot on eve and check that keyboard backlight is enabled as soon as the SOC starts booting Change-Id: I9ac78e9c3913a2776943088f35142afe3ffef056 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18197 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-21mainboard/google/reef: remove internal pullups on PP1800_S railAaron Durbin
The PP1800_S rail is turned off in S3. However, enabling internal pullups on the pins which are connected to PP1800_S results in leakage into the P1800_S rail. Fix this by disabling the internal pullups on PP1800_S rail pins. BUG=chrome-os-partner:61968 BRANCH=reef TEST=measured leakage on PP1800_S rail. Gone with this patch. Change-Id: I5ae92b31c1a633f59d425f4105b8db1c9c18c808 Signed-off-by: Aaron Duribn <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18189 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-20google/snappy: Add weida touchscreen supportWisley Chen
Add weida touchscreen as 2nd touchscreen source BUG=chrome-os-partner:61865 BRANCH=reef TEST=emerge-snappy coreboot, and verified that touchscreen works on snappy. Change-Id: If76312a62e97da9d5de18ad895e90ee6b0f0c6ae Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18166 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-20google/snappy: Use exported GPIOs and ACPI regulator for touchscreenWisley Chen
ELAN touchscreen device expects firmware to export GPIOs and ACPI regulators for managing power to the device. Thus, provide the required ACPI elements for OS driver to properly manage this device. BUG=None BRANCH=None TEST=Verified that touchscreen works properly on boot-up and after suspend/resume. Change-Id: I78e0c35f60289afe338d140d90784a433ca534ae Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18163 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-20google/eve: Adjust DPTF parametersDuncan Laurie
- Remove the 0mA entry for the charger performance table - Slightly raise the passive limit for TSR2/TSR3 to 55C BUG=chrome-os-partner:58666 TEST=manual testing on P1 system Change-Id: I75c66afe04afbbdb64a45833eb938e57ff21b392 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18172 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-20google/eve: Enable ACPI keyboard backlightDuncan Laurie
Enable the ACPI interface to EC driven keyboard backlight. BUG=chrome-os-partner:61464 TEST=manual testing on P1 system Change-Id: I13d96c13d7db726b1e8289131db65104bd302efe Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18171 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-20google/eve: Enable pull-up on ACPRESENTDuncan Laurie
Enable an internal pull-up on ACPRESENT signal. BUG=chrome-os-partner:58666 TEST=manual testing on P1 Change-Id: I0bb86f4547272e021ffd10998faa0e2f103b0808 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18170 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-19mainboard/google/snappy: Disable unused devicesWisley Chen
The following devices i2c6, i2c7, spi1, spi2, uart3 are not used. BUG=none BRANCH=master TEST=emerge-snappy coreboot chromeos-bootimage Change-Id: I9bacdbdd194ce21686c1618494d113402f2bef6c Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18140 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-19mainboard/google/reef: Ignore Audio DMIC IOSSTATEVaibhav Shankar
Audio DMIC PLL needs to be ON in S0ix to support Wake on Voice. This requires GPIO_79 and GPIO_80 to be configured as IGNORE IOSSTATE. So DMIC CLKs will be ON in S0ix. Change-Id: If91045a8664ce853366b670b9db38d620818fbab Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/18155 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-17Revert "mainboard/google/snappy: Add PowerResource for ELAN touchscreen"Martin Roth
This reverts commit 01ba8cf7 (mainboard/google/snappy: Add PowerResource for ELAN touchscreen) Change was out of date and broke the build. Change-Id: Id47631ece1172c3f93bf6f40b8686dfd728842a9 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18158 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-01-17mainboard/google/reef: Ignore SPI IOSTANDBYLijian Zhao
SPI controller need to access flash descriptors/SFDP during s0ix exit, so all fast SPI IO can't be put into IOSTANDBY state. For reef, that will be FST_SPI_CLK_FB, GPIO_97, GPIO_99, GPIO_100, GPIO_103 and GPIO_106. BUG=chrome-os-partner:61370 BRANCH=reef TEST=Enter s0ix state in OS, after resume run flashrom to read SPI content. Change-Id: I5c59601ec00e93c03dd72a99a739add0950c6a51 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/18137 Tested-by: build bot (Jenkins) Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-17mainboard/google/snappy: Add PowerResource for ELAN touchscreenWisley Chen
Define reset_gpio and enable_gpio for touchscreen device so that when kernel puts this device into D3, we put the device into reset. PowerResource _ON and _OFF routines are used to put the device into D0 and D3 states. BUG=chrome-os-partner:59034 BRANCH=master TEST=emerge-snappy coreboot chromeos-bootimage Change-Id: I08c05d06b2812a33b3fdff9b42b2a8e0653dd8b4 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/17366 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-17Combine Baytrail ChromeOS devices using variant schemeMatt DeVillier
Combine existing boards google/enguarde and google/ninja using their common reference board google/rambi as a baseboard. Variants contain board specific data: - DPTF ACPI components - I2C ACPI devices - RAM config / SPD data - devicetree config - GPIOs - board-specific HW components (e.g., LAN) Additionally, some minor cleanup/changes were made: - remove unused ACPI trackpad/touchscreen devices - correct I2C addresses in SMBIOS entries - clean up comment formatting - remove ACPI device for unused light sensor - switch I2C ACPI devices from edge to level triggered interrupts, for better compatibility/functionality (and to be consistent with other recently-upstreamed ChromeOS devices) The existing enguarde and ninja boards are removed. Variant setup modeled after google/auron Change-Id: Iae7855af9a224fd4cb948b854494e39b545ad449 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18129 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-17google/enguarde,ninja: Prep for variant mergeMatt DeVillier
Minor cleanup for enguarde and ninja devices: - enguarde: correct trackpad I2C slave address - enguarde: remove unused trackpad ACPI devices - ninja: remove unused PS2 keyboard ACPI device Change-Id: I1beb34059ba318e2d496a59e4b482f3462faf232 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18128 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-16mainboard/google/poppy: SD card changesFurquan Shaikh
1. Disable WP 2. Pass SD card detect info in ACPI BUG=chrome-os-partner:60713 BRANCH=None TEST=Verified that OS is able to detect SD card and read/write to it. Change-Id: Ide84d4b86c0fac50a07520dfd76d6d3a921f2ecc Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18138 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-16mainboard/google/poppy: Update DQS and DQ Byte mappings for poppyRizwan Qureshi
poppy schematics have undergone change after review, update DQS and DQ Byte mappings based on the new schematics. BUG=chrome-os-partner:61856 BRANCH=None TEST= Build and boot all the poppy proto SKUs to OS. Change-Id: Ie4532035f37c25540abb26122234f6e3346ede69 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18133 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-13mainboard/google/poppy: Disable EC SW syncFurquan Shaikh
BUG=chrome-os-partner:60513 BRANCH=None TEST=Verified that EC SW sync is disabled Change-Id: I399b26aa64084f5d5e91a2e585281dc48fa81c89 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18114 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-13mainboard/google/poppy: Enable touchscreen in ACPIFurquan Shaikh
BUG=chrome-os-partner:60513 BRANCH=None TEST=Verified that touchscreen works on poppy. Change-Id: I0fd605048b91b126ca5b5f8c1c4d6d3f46f866a3 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18113 Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: Martin Roth <martinroth@google.com>
2017-01-13mainboard/google/poppy: Correct the index for SPD binariesFurquan Shaikh
BUG=chrome-os-partner:60513 BRANCH=None TEST=Picks up correct SPD for index. Change-Id: Iac683ab3b8151747940b0ad7e257da3d9b0ac622 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18112 Tested-by: build bot (Jenkins) Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-13mainboard/google/poppy: Enable SD cardFurquan Shaikh
BUG=chrome-os-partner:60713 BRANCH=None TEST=sdcard is detected. Change-Id: I9ec0cabff0ed7973f5e7dd2c1eae346ae6a1aa99 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18111 Tested-by: build bot (Jenkins) Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-13gru: Tuning USB 2.0 PHY0 and PHY1 host-portWilliam wu
The commit 0ba3b2593b0c ("gru: Tuning USB 2.0 PHY to increase compatibility") bypass ODT to set the max driver strength for the Type-C otg-port, it works well on otg-port when connected with USB2.0 devices. Unfortunately, because the Type-C otg-port and host-port are consisted in one USB2 PHY, so bypass ODT will have an effect on both host-port and otg-port. I have tested the host-port eye-diagram, the result shows that if we bypass ODT, the host- port eye-diagram height will become to high, more than 500mv, this may cause USB 2.0 high-speed enumeration failure. This patch bypass ODT for host-port separately, and then we can reduce the host-port driver strength without affecting the otg-port driver strength. BRANCH=gru BUG=chrome-os-partner:60727 TEST=Boot system, run 'lsusb' command and check if the usb camera and usb bluetooth are on usb 2.0 hub or usb 1.1 hub. If they are on usb 1.1 hub, the issue happens. If not, try to run camera app and then close camera app, repeat until find that the usb camera is on the usb 1.1 hub. Change-Id: Ib693e2a6f2113c06692a7bfee22d85b67ee3b165 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 5ea7660b7b05080b76fc5ca5af3fa18552a03491 Original-Change-Id: Ia1f12182929673c5726df9f77f0903469b5c957a Original-Signed-off-by: William wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/425739 Original-Commit-Ready: Douglas Anderson <dianders@chromium.org> Original-Tested-by: Douglas Anderson <dianders@chromium.org> Original-Tested-by: Inno Park <ih.yoo.park@samsung.com> Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-on: https://review.coreboot.org/18126 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-13google/pyro: Add ELAN touch screen supportKevin Chiu
Current fw does not create ACPI device for OS to recognize ELAN touchscreen. List the touch screen in the devicetree so that the correct ACPI device are created. BUG=chrome-os-partner:61803 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I9015fa63ef3aba74b682da3608a05ee49c4947c5 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18086 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-04google/auron: Fix omitted ACPI KB backlight for variantsMatt DeVillier
Restores KB backlight functionality for auron variants gandof, lulu, and samus. TEST: boot Lulu and observe KB backlight functional Change-Id: Iaa852f9327ff1690111db610b4cc5266cd7925b4 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/17960 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-03Revert "google/oak: increase the driving strength for 4GB DRAMs"Nicolas Boichat
This reverts commit 34a6537512d412363bf56428b7ae284e6dd80fb3, which appears to cause random stability issues on some elm units. BRANCH=oak BUG=chrome-os-partner:60869 BUG=chromium:673349 TEST=None Change-Id: I5ce9e2673db1bc7a1f487a3c3bcce4651a5e3567 Reviewed-on: https://chromium-review.googlesource.com/419862 Commit-Ready: Nicolas Boichat <drinkcat@chromium.org> Tested-by: Nicolas Boichat <drinkcat@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18005 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-01-03google/snappy: Update DPTF settingsWisley Chen
1. Update DPTF TSR1/TSR2 passive/critial trigger points. TSR1 passive point:53, critial point:80 TSR2 passive point:90, critial point:100 2. Update PL1 Min to 4W and PL1 Max to 12W 3. Update thermal relationship table (TRT) setting. BUG=none BRANCH=master TEST=build, boot on snappy dut and verified by thermal team member. Change-Id: I8b4fb178daa7c2e4091a14779a125bd5e943d023 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/17955 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-03mainboard/google/reef: Update DPTF parameters EVT1_v0.3Tim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_EVT1_v0.3_20161227.xlsx) 1. Update DPTF CPU/TSR1/TSR2 passive/critial trigger points. CPU critical point:103 TSR1 passive point:45 TSR2 passive point:55, critical point:90 2. Change thermal relationship table (TRT) setting. Change CPU Throttle Effect on CPU sample rate to 3secs Change Charger Effect on Temp Sensor 2 sample rate to 60secs Change CPU Effect on Temp Sensor 1 sample rate to 8secs BUG=chrome-os-partner:60038 BRANCH=master TEST=build and boot on electro dut Change-Id: I3746750f7ea4a2e01153a36c28a5c33140c9e38c Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/17975 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-26google/eve: Enable internal pull-up on PWRBTN#Duncan Laurie
Enable an internal pull-up on the power button input as a quick press is resulting in power button override being asserted. BUG=chrome-os-partner:61312 TEST=tested on eve P0b to ensure quick power button press does not result in a shutdown due to power button override. Change-Id: I3028cf7faef309cf4d60c3585b48adab6e1549d4 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/17962 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-12-26mainboard/google/chell: Set TCC activation offset to 10 degree CSumeet Pawnikar
With the default TCC activation offset value as 0 and Tjmax temperature value as 100 degree C, Pcode firmware starts taking prochot action at 100 degree C [Tjmax-Offset]. But before Pcode firmware starts prochot action at 100 degree C, device is getting shutdown at 99 degree C due to DPTF critical CPU temperature. This patch sets TCC activation offset value to 10 degree C for thermal throttle action to prevent this kind of shutdown. BUG=chrome-os-partner:59397 BRANCH=None. TEST=Built, booted on skylake and verified target offset value. Change-Id: I0811ef481a4b3ce4bd6ef24f2aa8160f44f9c990 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/17921 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-23spi: Get rid of SPI_ATOMIC_SEQUENCINGFurquan Shaikh
SPI_ATOMIC_SEQUENCING was added to accomodate spi flash controllers with the ability to perform tx and rx of flash command and response at the same time. Instead of introducing this notion at SPI flash driver layer, clean up the interface to SPI used by flash. Flash uses a command-response kind of communication. Thus, even though SPI is duplex, flash command needs to be sent out on SPI bus and then flash response should be received on the bus. Some specialized x86 flash controllers are capable of handling command and response in a single transaction. In order to support all the varied cases: 1. Add spi_xfer_vector that takes as input a vector of SPI operations and calls back into SPI controller driver to process these operations. 2. In order to accomodate flash command-response model, use two vectors while calling into spi_xfer_vector -- one with dout set to non-NULL(command) and other with din set to non-NULL(response). 3. For specialized SPI flash controllers combine two successive vectors if the transactions look like a command-response pair. 4. Provide helper functions for common cases like supporting only 2 vectors at a time, supporting n vectors at a time, default vector operation to cycle through all SPI op vectors one by one. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: I4c9e78c585ad95c40c0d5af078ff8251da286236 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17681 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-22Add/Combine Broadwell Chromebooks using variant board schemeMatt DeVillier
Combine existing boards google/auron_paine and google/samus with new ChromeOS devices auron_yuna, gandof and lulu, using their common reference board (auron) as a base. Chromium sources used: firmware-yuna-6301.59.B 6ed8b9d [CHERRY-PICK: broadwell: Update to...] firmware-gandof-6301.155.B 666f34f [gandof: modify power limiting for...] firmware-lulu-6301.136.B 8811714 [lulu: update RAMID table] Additionally, some minor cleanup/changes were made: - I2C devices set to use level (vs edge) interrupt triggering - HDA verb entries use simplified macro entry format - correct FADT table header version - remove unused ACPI device entries / .asl file(s) - clean up ACPI code (e.g., trackpad on Lulu) - adjust _CID for trackpad on Lulu in order to not load non-functional Windows driver (does not affect Linux) - remove unused header includes (multiple/various) - correct I2C addresses used for SMBIOS device entries - correct misc typos etc The existing auron_paine samus boards are removed. Variant setup modeled after google/slippy Change-Id: I53436878d141715eb18b8ea5043d71e6e8728fe8 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/17917 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-12-22Combine Broadwell Chromeboxes using variant board schemeMatt DeVillier
Combine existing boards google/guado, rikku, and tidus using their common reference board google/jecht as a base. Additional changes besides simple consolidation include: - simplify power LED functions - simplify HDA verb definitions using azelia macros - use common SoC functions to generate FADT table - correct FADT table header version - remove unused haswell_pci_irqs.asl - remove unused header includes (various) - set sane default fan speed (0x4d) for all variants Variant setup modeled after google/beltino Change-Id: I77a2dffe9601734916a33fd04ead98016ad0bc4b Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/17913 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-14 13:30:29 +0000