| Age | Commit message (Collapse) | Author |
|---|
|
Add a function that initializes GPIOs based on the sleep type that
the system is coming back from. This allows initialization of the
fingerprint GPIOs which need to be handled differently between wake
from S3 and boot from S5.
On initial boot, the state of the FP sensor could be either
enabled or disabled. Because of this, on boot, we power off
the sensor for >200ms, to reset its state, then power it back on.
In suspend/resume, the fingerprint sensor should remain powered
the entire time.
If fingerprint is disabled on the trembyle-based board, set the pins
to no-connect. Dalboz doesn't have fingerprint and the GPIOS are
configured differently due to the FT5 chip having fewer GPIOS than
FP5, so nothing needs to be initialized there.
There were also a couple of trivial comment clean ups regarding the
FPMCU GPIOS.
BUG=b:171837716
TEST=Boot & Check GPIO states.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I16a2e621145782e0a908bb3e49478586c09a0e0a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds memory parts used by variant voema to
mem_parts_used.txt and generates DRAM IDs allocated to these parts.
Added memory
1. H9HCNNNCRMBLPR-NEE
2. H9HCNNNFBMBLPR-NEE
3. MT53D1G64D4NW-046 WT:A
BUG=b:172751925,b:172781673,b:172782100,b:172781562
TEST=emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ic832155448fb07152b906aa04ca49d384ec47b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47351
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The T3 that PPVARN_LCD low to LCM_RST_1V8 high is 0.1269ms and
it does not meet the LCD specification that the T3 must be larger
than 5ms. Because there is a delay between PPVARN_LCD_EN and
PPVARN_LCD. An extra 9ms delay should be added on LCM_RST_1V8
in order to meet the specification "ProductSpec_NV105WUM-A51_
V4.3_P2(TLCM).pdf".
BUG=b:172201138
BRANCH=kukui
TEST=The LCD sequence T3 is larger than 5ms when power on.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Iaf7ae494e30c4c207103d949287b335288688c54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Currently the decision of whether or not to use mrc_cache in recovery
mode is made within the individual platforms' drivers (ie: fsp2.0,
fsp1.1, etc.). As this is not platform specific, but uses common
vboot infrastructure, the code can be unified and moved into
mrc_cache. The conditions are as follows:
1. If HAS_RECOVERY_MRC_CACHE, use mrc_cache data (unless retrain
switch is true)
2. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_BOOTBLOCK, this
means that memory training will occur after verified boot,
meaning that mrc_cache will be filled with data from executing
RW code. So in this case, we never want to use the training
data in the mrc_cache for recovery mode.
3. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_ROMSTAGE, this
means that memory training happens before verfied boot, meaning
that the mrc_cache data is generated by RO code, so it is safe
to use for a recovery boot.
4. Any platform that does not use vboot should be unaffected.
Additionally, we have removed the
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN config because the
mrc_cache driver takes care of invalidating the mrc_cache data for
normal mode. If the platform:
1. !HAS_RECOVERY_MRC_CACHE, always invalidate mrc_cache data
2. HAS_RECOVERY_MRC_CACHE, only invalidate if retrain switch is set
BUG=b:150502246
BRANCH=None
TEST=1. run dut-control power_state:rec_force_mrc twice on lazor
ensure that memory retraining happens both times
run dut-control power_state:rec twice on lazor
ensure that memory retraining happens only first time
2. remove HAS_RECOVERY_MRC_CACHE from lazor Kconfig
boot twice to ensure caching of memory training occurred
on each boot.
Change-Id: I3875a7b4a4ba3c1aa8a3c1507b3993036a7155fc
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46855
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update I2C address for Goodix touchscreen and add ELAN touchscreen &
Synaptics trackpad device. Follow CB:47415 to correct HID over I2C
device to be level triggerd.
BUG=b:160013582
TEST=emerge-volteer coreboot and check system dmesg and evtest can get
device.
Change-Id: I070fb0e06b588f128253270502c9c2c427c62b84
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The option `HeciEnabled` was partly replaced by use of the device on/off
state in the devicetree in commit 3de90d1. The option has been removed
from the corresponding boards, so `HeciEnabled` is always 0 and ME
always gets disabled during soc finalize, when `HECI_DISABLE_USING_SMM`
is set.
Replace the option in the finalize function by the same dt state check
that sets the FSP option and drop the remaints of `HeciEnabled`.
Devicetrees still having `HeciEnabled` have been adapted to keep the
current behaviour.
Change-Id: Ib4cca9099b9aa3434552a41fbafca7cf6a0dd0eb
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47195
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select `PM_ACPI_TIMER_OPTIONAL` to enable the new PM ACPI Kconfig and
set the FSP option for PM ACPI timer enablement from its value instead
of using the old devicetree option.
Also drop the obsolete devicetree option from soc code and from the
mainboards and add a corresponding Kconfig entry instead.
Change-Id: I10724ccf1647594404cec15c2349ab05b6c9714f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45955
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of relying on mainboards to call it, do like Lynx Point.
Change-Id: Idb7457e0734e19d0a26f0762079e273b6e740475
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46793
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is identical for all Broadwell mainboards, thus deduplicate it.
Change-Id: I74559fbe42e44aa4d15ced5d88f6c15a1bf5203b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46792
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Google Wolf remains identical.
Change-Id: I710581156937b042ba4cf5948c65d0795ad37bbf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46789
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename it to `hostbridge.asl`, which is what Haswell uses.
Change-Id: I6f97fc5c9459fe6b66dcfcf51900c751beda0ebe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46786
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ifc6dd5f6549e7501f350afe8456a9a8096edcc25
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ida1b1d05b39e67a9eba3bfaecca37f38821a438b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ib2f203b5f5eea5c25cfd4543f5ed9f15101b1735
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ic334816712370da63471135da8dd598ab02d54ef
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: I75a92616f11054993ff5a5bfefce5c3f4638c07c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Iff00667377eecedcf0b83bcfc0bf50bd4c3411eb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: I1773973f64bcc5ef6bd1856c5d8eb998bb6a4888
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: I320198d56131cf54e0f73227479f69968719b2a7
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: Ie7b82ea07ef97b2096d75229c445bd3a65cb3be0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=emerge-dedede coreboot
Change-Id: I9d8fa57ae0f554896a4a0722e3e89567676382d4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable USB2 port 5 for user facing camera.
Enable USB2 port 6 for world facing camera.
BUG=b:169813211
BRANCH=None
TEST=build metaknight firmware
Change-Id: Iecb7787d46eab7096dec9f838a16da101105e09a
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Disable I2C port 3 for metaknight
BUG=b:169813211
BRANCH=None
TEST=build metaknight firmware
Change-Id: Ic4a056d53a8c8abd04a9b786428da0986a255276
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Work on this mainboard was abandoned and never finished. It's not really
usable in its current state, so let's get rid of it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4cd2e2cd0ee69d9846472653a942fa074e2b924d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change switches the selection of CAR mode so that
INTEL_CAR_NEM_ENHANCED_V2 is the default unless mainboard
selects INTEL_CAR_NEM. INTEL_CAR_NEM is selected only by
mainboards using older silicon (ES1 or ES2) that did not
support NEM enhanced mode.
This enables NEM Enhanced Mode for TGL-U/Y RVPs.
Bug=b:171601324
BRANCH=volteer
Test=Build coreboot for volteer. Boot on SKU that has 4MB L3 cache.
Change-Id: Ib6e041261cb8ca9c6e602935da4962aac0d9ece5
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The other two modes are not used by any mainboard, and the code seems to
be copied from older southbridges. As the code looks incorrect, drop it.
Change-Id: I374546279a85cead1aea13e0952bbfd6f643a75b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Create the shuboz variant of the zork reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:172021093
BRANCH=none
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I3f62625f8cbde1c9adf8ab335edeb9e811e32679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47152
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adds ACPI properties for WDT8762A device.
Per spec v0.8
HID name WDHT2002
T14=100ms
BUG=b:163561649
BRANCH=puff
TEST=emerge-puff coreboot and check system dmesg and evtest can get device.
Change-Id: I178e9d5aa1e1501d33b3cd4092f3f522bb6f1a74
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Create the genesis variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:172620124
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_GENESIS
Signed-off-by: Matt Ziegelbaum <ziegs@chromium.org>
Change-Id: I70886c2c5a25f5de1a4941ff235547ee812fa50d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Add information regarding the privacy pin on the overridetree and the
gpio.
BUG=b:171888751
Change-Id: I1ab19a863715ba5a928dd7c16402d398e5475edc
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add information regarding the privacy pin on the overridetree and gpio.
BUG=b:169840271
Change-Id: Ifa628dda03f3f65976850aeabaf516f528a921b7
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update Power Limit2 (PL2) minimum value to the same as maximum value
for magolor board. DTT does not throttle PL2, so this minimum value
change here does not impact any existing behavior on the system.
BUG=b:168353037
BRANCH=None
TEST=Build and test on magolor board
Change-Id: I74e960de506d366cba2c8aefb23f9e69337fd163
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
LTE module used in boten has a specific power on/off sequence.
GPIOs related to power sequnce are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: Power off -> 500ms -> Power on
Configure the GPIOs based on these requirements.
BUG=b:163100335
TEST=Build and boot Boten to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ic6d5d21ce5267f147b332a4c9b01a29b3b8ccfb8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This support is required to power off certain components that exist only
in certain variants.
BUG=None
TEST=Build and boot Boten to OS.
Change-Id: Ib43ada784666919a4d26246a683dad7f3546fabb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Wang <pwang12@lenovo.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds memory parts used by variant voema to
mem_parts_used.txt and generates DRAM IDs allocated to these parts.
Added memory
1. MT53E512M64D4NW-046 WT:E
2. MT53E1G64D8NW-046 WT:E
BUG=b:171755775
TEST=emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I24d466f92a7e0fa3ab2f6241f0b5af025c53ed98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This patch makes Atlas resume from S0ix by AC plug and unplug.
BUG=b:165328935
BRANCH=atlas
TEST=Put Atlas in suspend. Wake it up by AC plug.
TEST=Put Atlas in suspend. Wake it up by AC unplug.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I95676d785bfc1488a8c1bdd3d56f2c38d95f3fb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
EEPROM in the camera module does not require any specific power
resources. This will ensure that no unnecessary resources are turned on
while accessing the camera EEPROM.
BUG=b:167938257
TEST=Build and boot to OS in Drawlat. Ensure that the camera EEPROM is
listed in the output of i2cdetect.
Change-Id: Iece9b3f657bf94a21cc08bf1745353575858f9b2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Handle AC connect and disconnect notifications from Embedded Controller
(EC) and wake from S3/S0ix.
BUG=b:172266344
TEST=Build and Boot to OS in Drawlat. Ensure that the system wakes up
from suspend on AC connect and disconnect on both the TypeC ports.
276 | 2020-11-04 12:21:29 | S0ix Enter
277 | 2020-11-04 12:21:40 | S0ix Exit
278 | 2020-11-04 12:21:40 | EC Event | AC Disconnected
279 | 2020-11-04 12:21:57 | S0ix Enter
280 | 2020-11-04 12:22:03 | S0ix Exit
281 | 2020-11-04 12:22:03 | EC Event | AC Connected
282 | 2020-11-04 12:22:35 | S0ix Enter
283 | 2020-11-04 12:22:47 | S0ix Exit
284 | 2020-11-04 12:22:47 | EC Event | AC Disconnected
285 | 2020-11-04 12:23:08 | S0ix Enter
286 | 2020-11-04 12:23:16 | S0ix Exit
287 | 2020-11-04 12:23:16 | EC Event | AC Connected
Change-Id: I7fa4ac0096548fd63af86e9f56c4c1ee25491399
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update Power Limit2 (PL2) minimum value to the same as maximum value for
dedede variants (baseboard and drawcia). Currently, variants like boten,
waddledee, waddledoo, metaknight and wheelie uses the DTT entries from
baseboard devicetree since there is no override present for these variants.
So, these variants will also reflect this change of PL1 minimum value.
For madoo variant, PL2 minimum value already set the same as PL2 maximum
value. DTT does not throttle PL2, so this minimum value change here does not
impact any existing behavior on the system.
BUG=None
BRANCH=None
TEST=Build and test on drawcia system
Change-Id: I7ecf1ffcc7871192ebe18eb8c3c3fd3e1193721e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47154
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
InternalGfx isn't used so drop it.
Change-Id: I12f424d8d883e065ef8d007e56a8bff41a7fae53
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Config voema to use CSE LITE
BUG=b:171755775
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ic4ca82ce844e6367da70ed052445943572ae7b09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:171755775
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ibedbbe8f9ac039cbde114ace3266ec067a4003ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Production Volteer devices have Cr50 TPM connected via SPI, depending on
Cr50 firmware version it may or may not support long enough interrupt
pulses for the SoC to safely be able to enable lowest power mode.
Some reworked Volteer devices have had the Cr50 (Haven) TPM replaced
with Dauntless, communicating via I2C. The I2C drivers do not support
being accessed early in ramstage, before chip init and memory
mapping, (tlcl_lib_init() will halt with an error finding the I2C
controller base address.)
Since the Dauntless device under development can be made to support
longer interrupts, or a completely new interrupt signalling mode, there
is no need to try to go through the same discovery as is done via SPI.
This CL will skip the discovery, enabling the S0i3.4 sleep mode in all
cases, on the reworked test devices.
BUG=b:169526865, b:172509545
TEST=abuild -t GOOGLE_VOLTEER2 -c max -x
Change-Id: I08a533cede30a3c0ab943938961dc7e4b572d4ce
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47049
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current I2C3 bus frequency is 341 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C3 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C3 frequency is 394kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: Ie1ef95bb39d71fbb113120a0ec88305bc23e7ab9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This setting copy from puff reference board
and should measure again after whole system build.
BUG=b:155261464
BRANCH=puff
TEST=emerge-puff coreboot and check system speaker has sound output.
Change-Id: Idd5c3276e9306e81ea766d14ed1415a68dedc2ad
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47161
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust USB2 phy si setting fine tune on DVT for Ezkinil.
BRANCH=zork
BUG=b:156315391
TEST=Measuring scope timing and test usb detection
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: Id537b6e9a17f47481b6aedcea0c6a8474d993b6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update gpio and devicetree for elemi.
BUG=b:170604353
TEST=emerge-volteer coreboot and boot into kernel
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I5b8880d485ed73aa4e65c1249c58f02c8f0c6501
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Config elemi to use CSE LITE
BUG=b:170604353
TEST=emerge-volteer coreboot
Change-Id: I31c7a743645d6a34ee34e750ba92c108b306ee09
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47019
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:170604353
TEST=emerge-volteer coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I1a1ab6f3d57d5023523b85bfb00d48d8b70a6c1f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use command below to change the variable globally.
sed -i "s/\<variable\>/variable_u/g" `grep variable -rl ./ \
--exclude-dir=build --exclude-dir=crossgcc`
BUG=b:171334623
TEST=Build
Change-Id: I056a76663e84ebc940343d64178c18cb20df01a3
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add new SKU definition:
Garg360 (LTE DB,1A2C,TS, no stylus, rear camera) SKU ID - 39
BUG=b:170708728
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage
Change-Id: Ifec4e1360bd1aff3825bc6413b0a2ccd8b822075
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47015
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the mainboard Kconfig is sourced before the SoC one, it would
still be possible to override this setting at mainboard level, even
though that shouldn't be needed. The maximum CPU count for Picasso is 8,
since the chips have only up to 4 cores with up to two threads each.
Change-Id: I53449b8fa73c5d13e6ea77bee6eed8896b7d3ec3
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47205
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the `GWAK` method into the GPIO device, and have lpc.c include the
LP GPIO code. All usages of `GWAK` on mainboards need to be updated.
Change-Id: Id6a41f553d133f960de8b232205ed43b832a83d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46775
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated 'dsdt.dsl' files are identical.
Change-Id: I7d4fc3acd82023b007d80638bcb71476330ef320
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Built google/beltino (Monroe) provides identical 'dsdt.dsl'.
Change-Id: I12b6a8264e53ece30ae79da2d79c6f1d302fb357
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Update dq/dqs mappings based on voema schematics.
BUG=b:169356808
BRANCH=volteer
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I1aae4286278e712bf29ebb15738477828d3f74d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I3a3d187fc24ab752dfe61893c15561a92d009fe2
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46062
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This CL is entirely generated by running the automatic formatter on this
one file.
BUG=None
TEST=abuild -t GOOGLE_VOLTEER2 -c max -x
Change-Id: Ibdd8cc2222e7af11c11df963b088ca2db07a3214
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change adds the callback
`elog_gsmi_cb_mainboard_log_wake_source()` to volteer to enable
logging of EC events in case of S0ix resume.
BUG=b:172272078
BRANCH=volteer
TEST=Verified that EC events are logged correctly for S0ix resume:
11 | 2020-11-02 14:11:05 | S0ix Enter
12 | 2020-11-02 14:11:08 | S0ix Exit
13 | 2020-11-02 14:11:08 | Wake Source | Power Button | 0
14 | 2020-11-02 14:11:08 | EC Event | Power Button
15 | 2020-11-02 14:11:17 | S0ix Enter
16 | 2020-11-02 14:11:21 | S0ix Exit
17 | 2020-11-02 14:11:21 | Wake Source | GPE # | 112
18 | 2020-11-02 14:11:21 | EC Event | Lid Open
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7aa9dc2470da3226925927f2a0cc39fdd426e3b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47142
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I7f87085c70149d02c544e2d43e1bdb58c7502d6d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46754
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SCONFIG complains because of the duplicate devicetree entry.
Change-Id: Ibdd60efdbcee5bda7c570d4b98f29cc8ede584cb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jes Klinke <jbk@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add the USB ports to the devicetree for describing them in ACPI,
including defining the port relationships and defining the reset
GPIO for the bluetooth device.
BUG=b:151731851
TEST=tested on volteer, all other boards were checked against the
latest available schematic.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ia1e5b71e7750a478ff79372c48616bbf5c21b79c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Define option value 6 for DB_USB where there is a Type-A port but
no Type-C port on the daughterboard.
BUG=b:151731851
TEST=build volteer boards
Change-Id: I489d24316556dedfecd821e502f1461010b1400f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The Kakadu project will be using eMCP board design.
BUG=b:171841122
TEST=Boots on chromebook Kakadu successfully.
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I44668ce630758e49fbf2c6028f56c01f83ff08f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46871
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
variant_smi_sleep is called in smm stage so we need to add
variant.c into smm stage. Otherwise it will call the dummy one.
BUG=b:168075958
BRANCH=octopus
TEST=build image passed.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I41df1a30b119ab3e04f9ae01955b6044f137527f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46847
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For development of the firmware to run on the Dauntless TPM, a number of
Volteer2 devices are being reworked to replace the H1 chip with probe
wires to connect to an external Dauntless development board.
Some modification to the AP firmware is required, not least because the
Dauntless chip is connected via I2C bus, instead of SPI. Most of the
Dauntless developers will not otherwise have a Chrome OS chroot.
Because of the above, I think it makes sense to have a new variant, for
the reworked devices, which I intend to create with this CL.
BUG=b:169526865
TEST=abuild -t GOOGLE_VOLTEER2_TI50 -c max -x
Change-Id: Ibdcd6c2ce3941c229518f21f0e479890b5d76dd1
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory part being added is:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
K4UBE3D4AA-MGCR
BUG=b:169813211
TEST=Build the metaknight board.
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: I0d0d22f4790f66b5265803e4dcf01234a16b1993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable SaGv for terrador.
BUG=b:171763116
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie00166a619424a67f70f870e55822ae2cc6d023d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Configure board specific DPTF parameters for delbin
BUG=b:168958222
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I69aa6046fdc90a2cf59ea3a13fdb15c8bc0d29a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46676
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the voema variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171755775
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOEMA
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4e1872d1ebff6fefdfb232f1ff82fce95a1ec643
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47007
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add G2Touch touchscreen support for dood.
BUG=b:171526389
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage, and check touchscreen
work.
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: Ica7d893de285c2dd1efcd43ac74919bdd5d5ac17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46675
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touch support and update Goodix settings.
BUG=b:157265632
BRANCH=zork
TEST=emerge coreboot and check both touch screen are workable.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Icfc2421061e8b3163d7d5108673351bc17df20ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Terrador and Todor are fanless design, so disable DPTF active policy.
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I53a33b8706d7a7d4013a2a5627a620223fcffc3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46874
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO D4 was used for camera reset for both front and rear cameras
(RCAM_RST_L/FCAM_RST_L) in RIPTO. For later volteer versions,
GPIO F15 is dedicated to the rear camera reset (RCAM_RST_L).
Before, BOARD_GOOGLE_VOLTEER flag was used for setting the right
RCAM_RST_L per volteer version. However, we don't support RIPTO
anymore. Also using flags for different volteer version support can
be error-prone. Removing RIPTO support.
BUG=b:171726823
BRANCH=none
TEST=Build and boot volteer proto2 or later version. Camera should
work without an issue.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I961fc17092887b4807c12c95f7139bb7e7b33e91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46826
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The camera privacy LED blinks during the boot and this gives a wrong
impression to the users that the camera is being used during the power
up. The blink happens when the camera module is probed and a series of
kernel patches and coreboot patches are being submitted to resolve the
issue.
The kernel patches are submitted to the chromium gerrit.
https://chromium-review.googlesource.com/2403386
https://chromium-review.googlesource.com/2403387
https://chromium-review.googlesource.com/2403385
https://chromium-review.googlesource.com/2403384
https://chromium-review.googlesource.com/2403383
https://chromium-review.googlesource.com/2403382
https://chromium-review.googlesource.com/2403381
https://chromium-review.googlesource.com/2403380
This is to separate the power resource for the VCM so that it can be
controlled by the driver and suppress the LED turn on.
BUG=b:169049942
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check if it blinks. It should not blink.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Id51c98e42c5f20e231d8096c9d2d98deebc7c968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
|
|
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:169645448
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a04320b0e2441dce540a5afdc461f12de45c41b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
We all knew this was coming, 32 bits is never enough. Doing this early
so that it doesn't affect too much code yet. Take care of every usage of
fw_config throughout the codebase so the conversion is all done at once.
BUG=b:169668368
TEST=Hacked up this code to OR 0x1_000_0000 with CBI-sourced FW_CONFIG
and verify the console print contained that bit.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6f2065d347eafa0ef7b346caeabdc3b626402092
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45939
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib51764da5b3c029f9ac7ac60199a0aedfc7f29b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45878
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C5 frequency is between 389-396kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: If0803a74ba9071acf15486ce4038261c1681a92f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Flesh out the PCH configuration into a separate chip. Keep it within the
Broadwell SoC directory for now, to ease moving files around. The boards
were prepared beforehand and the devicetrees require next to no changes.
Tested on out-of-tree Acer Aspire E5-573, still boots.
Change-Id: I28d948f3e6d85e669d12b29516d867c1d1ae9e1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46700
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`chip` entries are only hooked up via device nodes to the tree. A `chip`
without a `device` below it does nothing. To allow variants to override
SATA tuning parameters, ensure a device exists under the PCH chip scope.
Without this change, some variants would not properly override the SATA
tuning parameters after extracting the PCH parts into a different chip.
TEST=Sanity-check static.c and verify overridetrees override properly.
Change-Id: I013dbe1403567b93c8ee0e66f76481f2a3f42796
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46769
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I0fa486b8a0fc8be974f37d0bb4eb77a254e8cd86
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46703
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:170604353
BRANCH=volteer
TEST=emerge-volteer coreboot, and boot into kernel.
Change-Id: If354aa158f3ad60193268f38278a44f9c99bf3db
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46770
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the ambassador variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171561514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_AMBASSADOR
Signed-off-by: Matt Ziegelbaum <ziegs@chromium.org>
Change-Id: Ib0e3a813a120a4a8e984f3a89dc3ba100d94da95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove code to turn on backlight during ACPI mode because backlight has
been properly enabled in ACPI.
BUG=b:158087989
BRANCH=Zork
TEST=tested backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I3bf06042aa19e4559127d611d401f0ba0516b3a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Generate acpi methods which enable and disable backlight during _INI,
_WAK, and _PTS.
BUG=b:158087989
BRANCH=Zork
TEST=check backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I2f3434dc92de1f697693ff69ca15bd76647b89a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46671
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add internal pull-down for GPP_D19 to improve DMIC noise issue on
nightfury.
BUG=b:171669255
BRANCH=firmware-hatch-12672.B
TEST=Built and checked GPP_D19 voltage after booting
Change-Id: Ie63f260be3d6a55f91908db59312b3b0a8af98f4
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
To support gpio reset SoC, we need to pass the reset gpio parameter to
BL31.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I2ae7684a61af76693605cc0bcf8d20c8992c7bff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46388
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The pins for SD and MMC must be configured properly
so we can access them in payloads.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Ie6bdffb987d5acf286645550f1c53f294f71c38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:171478764
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Change-Id: I213fed2b56f216747b2727b69f97d46d8c0c872e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46701
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
invoke LTE power off function to meet LTE power sequence while DUT is
in reboot state.
BUG=b:167565015
BRANCH=octopus
TEST=build and verify on the DUT with LTE
Change-Id: I825cefb524ddaf9a9cb6add31c2ee0eea484f978
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46022
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, all variants remain identical.
Change-Id: I2b088b36c8e9ff9cbd47d625b14fc45ebd96532a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46702
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I9f5b81815f86db7bdcea95a95b9c9b235b4a34b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46613
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The LCM ID is not really used on Jacuzzi followers and the reference
design expects ADC to return 0. However, there were hardware design
issues so the returned value became unexpected numbers.
- Juniper and Kappa returns 1.
- Burnet and Esche returns 1 on normal boot, and 0 on recovery boot.
- Cerise and Stern usually returns 0, and sometimes 1.
To fix that, we are changing LCM ID to fixed value for Jacuzzi followers.
BUG=b:170916885,b:171365301
BRANCH=kukui
TEST=1. emerge-jacuzzi coreboot
2. check burnet/esche skuid correctly
Change-Id: I3b43b9153315ec65e9168c4e84ea844dff14d446
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
1. Enable dptf feature and remove fan control part from overridetree.cb
2. Update tcc offset to 5
3. Follow thermal validation and update PL2 max_power to 51
BUG=b:167931578, b:170357248
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I99e429b90ed7de08385fe51ca742865b1266eef9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 214c719eed83967b8f0564feca65eebb3d83f5bc.
CB:45857 overrides the GPIO PM configuration if Cr50 does not support
long interrupt pulse width. More recent Cr50 Firmware versions support
long pulse width and hence the GPIO PM can take the default
configuration.
BUG=None
TEST=Build and boot Drawlat to OS. Ensured that 200 iterations of
suspend/resume sequence, warm and cold reboot cycles each are
successful.
Change-Id: I8e3be42cd82fd3ae919d23d6f19c84a90b9c737a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Enable front camera power in ramstage.
BUG=b:169170677
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I8b5a9a8333ed518883aa3664a115a4ba2e8a0218
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Add goodix touch pad as below:
HWID : GXTP7288
CID : PNP0C50
I2C address : 0x2C
I2C speed : 400Khz
HID Descriptor Address : 0x20
BUG=b:171351666
BRANCH=octopus
TEST=build image and verify goodix touch pad working.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idb4f8d3aff09712dcc98c8ae0c9ae30dc4049e29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46614
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
