| Age | Commit message (Collapse) | Author |
|---|
|
Currently WWAN_AUX_RST_L is in S5 domain and does not get asserted on
S0i3 entry. Based on the schematics, the pull-down on that signal leads
to 10 mW power leakage on S0i3 entry. Assert the signal on S0i3 entry to
achieve some power savings and de-assert it on S0i3 exit.
BUG=b:195748540
TEST=Build and boot to OS in Guybrush. Ensure that the signal gets
asserted on S0i3 entry and de-asserted on S0i3 exit. Trigger
suspend/resume cycles and ensure that the WWAN module is enumerated
after each cycle.
Change-Id: I43c8655ee5209779748e4365db973e094cb08aca
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58275
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Init overridetree based on the schematics.
Refer to brya0/overridetree.cb to update the settings of the devices
including DPTF, WIFI, NAU8825 and etc.
Refer to kano/overridetree.cb to update the SSD settings (pcie4_0).
TODO: DPTF and USB positions will be further updated later.
BUG=none
TEST=Build Pass
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I30d26a47fe93736c63b578c9180b148ef73e8b9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently override speed config is applied only for non EM100 cases.
For EM100 case, override speed board version defaults to 0 leading to
"comparison of unsigned expression >= 0 is always true" error. Fix this
error by defining the override speed config for both EM100 and non-EM100
use-cases.
BUG=None
TEST=Build Guybrush for both EM100 and non-EM100 cases.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Id8ee7b01c69c4555d6e6a7b0d5f095ea3aaf3405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58309
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No need for dynamic config (and the additional RAM training time)
on a Chromebox; always use high power/high performance mode.
Change-Id: I0295bac619af45a0d82da2bf39985c8bdcb77d5e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
No need for dynamic config (and the additional RAM training time)
on a Chromebox; always use high power/high performance mode.
Change-Id: I8ad773d1c616b746235ec67b98b83c5910464140
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add support to override SPI fast speeds based on board version from both
bootblock and verstage. Overrides apply for Guybrush only and SPI speed
is overridden from 66 MHz to 100 MHz starting board version 4. This will
help to improve the boot time on board version by ~60 ms and still allow
the old boards to boot with 66 MHz.
BUG=b:199779306
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5bf03ab8772f27aca346589e9c5662caf014d0d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
update fw_config for nipperkin
BUG=b:196909635
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Icd2c5509450e70aed158f146179f3a7fa24b547a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Some poppy variants did not select a system type, which led to the
default desktop type being set. Select the best fit enclosure type
for each variant.
Alphabetize the variant-specific options for improved readability.
Change-Id: I7c23f8fa3ae1de67f7a68b8a4e9ec16c4e8044df
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
1. Samsung K4U6E3S4AB-MGCL
BUG=b:202480992
TEST=emerge-dedede coreboot
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I811f32defd50a940a09f238d38c962d2caf42855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Update MAX98360 ACPI HID from "MX98357A" to "MX98360A"
BUG=b:198716348
TEST=Build nipperkin, codec is functional with new machine driver.
Cq-Depend: chromium:3195465
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: I8a1155848856db0cc4f42cfee0d914f8d1186b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
coreboot normally owns PCIe resets for all Cezanne based systems.
However during S0i3 resume coreboot cannot intervene for S0 GPIOs
(S5 carry over fine) so we needed an alternate way to de-assert
this reset on guybrush. This change feeds in the given S0 reset
GPIO (69 in this case) so that SMU may de-assert this reset on
S0i3 resume.
BUG=b:199780346
TEST=With latest FSP verify SD device trains each of 10 cycles
Cq-Depend: chrome-internal:4157948
Change-Id: Ieee31651db30147fda84ee1aa31df7cb1c206356
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58198
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
bootblock_mainboard_early_init gets called before console_init.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia5a1da336e8dfc451177a5319a656c407c9fef7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Document what setting the PM_ACPI_S5_LPC_PIN_MODE and
PM_ACPI_S5_LPC_PIN_MODE_SEL bits causes. The corresponding code will
eventually be factored out and moved to the Cezanne SoC code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I10e3eee5cfc1c5ba2c88b8b7e83e96e481f787e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Since the LPC_LDRQ0_PD_EN gets set right after it got cleared, we can
remove the clearing of that bit. This is split off from the previous
patch to be able to use timeless build to verify that the previous patch
didn't change any behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb300e7c7ce7e74c32ebdade0360ee4bd499b11a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
It's hard to understand what this code is doing because it uses hard
coded values, so use the register and bit defines instead.
BUG=none
TEST=Timeless build for guybrush results in identical binary.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2d74ed3b9b4984ab1e2a22c50375baf9c9589df0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fizz's USB ACPI code is intended to allow the OS to control port
charging power, but since Fizz's ports are dumb (vs smart), it
controls power to the port itself. The end result is that active
ports become disabled when rebooting from Windows (10/11), and
power is not restored until the device is powered down (a warm
reboot is not sufficient).
Subsequent Chromebox models (eg, Puff-based variants) don't bother
with EC-controlled USB port power, so just drop it since it's
problematic and provides no benefit.
Test: boot Windows 10/11, reboot, observe active USB ports still
functional (eg, USB KB still works)
Change-Id: I2c13d49b3ce8de8b0a38512db3c57d0c8ecbf0ad
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Caroline uses a Wacom digitizer, so adjust the ACPI HID
so that the proper drivers attach under Windows/Linux.
Change-Id: I732b09001dc41a91a32a5f9260abdab435b28b8a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Before attempting another commit 6260bf71 (vboot_logic: Set
VB2_CONTEXT_EC_TRUSTED in verstage_main), ensure that guybrush builds
chromeos.c in verstage to call get_ec_is_trusted() in vboot
verstage_main().
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: Ic22519fdde1b18f6ce0237022dee02ca37181a74
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Before attempting another commit 6260bf71 (vboot_logic: Set
VB2_CONTEXT_EC_TRUSTED in verstage_main), ensure that guybrush programs
GPIO_EC_IN_RW (GPIO_91) as an early GPIO so that it can be read from in
verstage.
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: Ia6dcb225bbca89f3a873aad75a7d67625cdd3742
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define FW_CONFIG bits 41 - 43 (SSFC bits 9 - 11)
for codec selection.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:198713670
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Iaba136a836b89f42411474ae733380e345cce687
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58162
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Synaptics touchpad device support in devicetree.
BUG=b:201043984
BRANCH=dedede
TEST=Touchpad device function is OK
Change-Id: Ifb240d7113e401de827384697fc752a76fbf7ac7
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable CHROMEOS_DSM_PARAM_FILE_NAME to report dsm parameter file name.
BUG=b:197076844
TEST=build and check SSDT.
Change-Id: I726e5854bc6a8fb125cb3b7572ddedff49c3c403
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add ALC5682-VS codec support in corori.
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO field of ssfc.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:201372531, b:194436265
TEST=ALC5682-VD/ALC5682-VS audio codec can work.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I2f3edb0b594066714b42050a411103a215e68b12
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
|
|
nipperkin has different H/W topology to guybrush that the eMMC device
is on a different GPP:
guybrush: GPP3
nipperkin: GPP2
Hence we need to enable RTD3 for nipperkin additionally which refers
to this one:
https://review.coreboot.org/c/coreboot/+/54967
BUG=b:200246826
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
run suspend test on eMMC sku
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I1dca8f9e4739514d2d024374d8686f27b25582a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Before attempting another commit 6260bf71 ("vboot_logic: Set
VB2_CONTEXT_EC_TRUSTED in verstage_main"), ensure that brya's variants
all program EC_IN_RW as an input GPIO in bootblock so that it can be read
from in verstage.
Change-Id: I6b1af50f257dc7b627c4c00d7480ba7732c3d1a0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Hsuan-ting Chen <roccochen@google.com>
|
|
BT offload hardware design is using only i2s0 pins. Need to disable
i2s2 pins which are not used. As per the hardware spec there is an OR
operation between vgpio and physical gpio pins related to i2s2. During
BT offload configuring the i2s2 pins to its native function is causing
offload issue on proto 2 boards.
BUG=b:201736222
TEST=Verified BT offload on brya on proto 1 and proto 2.
Change-Id: Ifbc53848c6ad12e537216cac3c2871088c094f3d
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
As we checked the panel doesn't display firmware screen if we hold
GPP_D5(TOUCHSCREEN_RESET) low on bugzzy. It's because of that bugzzy
uses the built-in touch screen on the panel, the panel seems like
under reset state by the TOUCHSCREEN_RESET signal.
This change sets default GPP_D5 level to high for bugzzy.
BUG=b:None
BRANCH=dedede
TEST=built and verified bugzzy showed firmware screen
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I53e4fc52ceb14ba23c22d3c105f65634b09029f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward Doan <edoan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This patch adds the setting of PsysPmax to 145W according to
the brya board design.
BUG=b:195615830
TEST=emerge-brya coreboot chromeos-bootimage & ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: I996a11f76fdc0c8babe0037219f5b43e45e459dd
Signed-off-by: Ryan Lin <ryan.lin@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
SHRM is a system hardware resource manager. It is used to manage run time
DDRSS activities. DDRSS stands for DDR subsystem.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
by trying DDR clocks which through SHRM RSI command.
Change-Id: I44484573a829eaefbd34907c6fe78d427506a762
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
These issues were found and fixed by codespell, a useful tool for
finding spelling errors.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie34003a9fdfe9f3b1b8ec0789aeca8b9435c9c79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
New boards introduced to trogdor family.
BUG=b:201263032
BRANCH=none
TEST=make
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I8299ddda14eb82103f17f8464a14992aa757afa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
GPIO PM was disabled for brask to evaluate if longer interrupt pulses
are required for ADL. Since ADL requires 4us long pulses (EDS:626817),
GPIO PM can be enabled. This change drops the GPIO PM override and
re-enables dynamic GPIO PM.
TEST=Boot brask to OS, ensure no TPM errors.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b8b66b5526d8b80775cb7588ce6b12181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable SMBus to support DDR4 SODIMM for brask. Enable 'smbus' in
brask device tree and add SPD addressese for the two DIMMs.
Separate the Kconfig items of brya and brask. Move
HAVE_SPD_IN_CBFS and CHROMEOS_DRAM_PART_NUMBER_IN_CBI to brya
and add config SPD_CACHE_IN_FMAP to brask.
Add a new section RW_SPD_CACHE to fmd for caching SPD data.
The renamed romstage.c is used by both brya and brask and a new
function variant_get_spd_info is provided to support the different
SPD source types.
BUG=b:194055762
BRANCH=None
TEST=build pass
Change-Id: I41c57a3df127356b8c7e619c4d6144dc73aeac72
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Correct OVTI2740 information for Kano:
MIPI camera CIO port, HID and Link Freq
BUG=b:200974074
TEST=Build and boot on Kano
camera driver is not probed before,
and it can now be probed properly
after this change.
Signed-off-by: Lai, Jim <jim.lai@intel.com>
Change-Id: I4612c9d42cd59cba0991b763224f77b7af33770b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
1. The original algorithm for I2C speed cannot always make the
timing meet I2C specification so a new algorithm is introduced
to calculate the timing parameters more correctly.
2. Some I2C buses should be initialized in a different speed while
the original implementation was fixed at fast mode (400Khz).
So the mtk_i2c_bus_init is now also taking an extra speed
parameter.
There is an equivalent change in kernel side:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/i2c/busses/i2c-mt65xx.c?h=v5.15-rc3&id=be5ce0e97cc7a5c0d2da45d617b7bc567c3d3fa1
BUG=b:189899864
TEST=Test on Tomato, boot pass and timing pass
at 100/300/400/500/800/1000Khz.
Signed-off-by: Daolong Zhu <jg_daolongzhu@mediatek.corp-partner.google.com>
Change-Id: Id25b7bb3a76908a7943b940eb5bee799e80626a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58053
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update bugzzy device tree override based on the EVT schematics.
BUG=b:195215785
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: Iba8e3fd24461b4228c6e6fa933c0093e3e45ee97
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update initial gpio configuration for brask
BUG=b:197385770
TEST=emerge-brask coreboot
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I71026565b876739d2a08ef79940f47c476ca70a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58041
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move MILLIWATTS_TO_WATTS macro in power_limit header file
so all other files can use the same macro.
BUG=None
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Ic7ecba06b0e0a47546f7307cbfbc3ce0fc634bc3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
M.2 spec describes PERST# should be sequenced after power enable.
Follow up commit 658d7c5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I508f7e21888cc1938aa9a6f0066c17029773974b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
M.2 spec describes PERST# should be sequenced after power enable.
Follow up commit 658d7c5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I494e0edc135d730cf7bb437f0196cdf233d970d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update GPIO GPP_B5 and GPP_B6 based on schematics.
BUG=b:197385770
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If83e02eec7c48b9ab41d346aa8baef7c0c881df1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
Add Synaptics touchpad for kano.
BUG=None
TEST=emerge-brya coreboot and check touchpad function work.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Iec43aaa9525309d2a0e3c9822038869786f5fe66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
M.2 spec describes PERST# should be sequenced after power enable.
BUG=b:201512872
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ie164ddb29f947e190fa87b31165e3c84b07926e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58034
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In CB:52662 when MIPI display support was added, we accidentally changed
the code flow for eDP displays such that i2c_init() will no longer be
called when display_init_required() is false. This is a problem because
on this platform, i2c_init() does not just prepare the I2C controller
for firmware use, it also loads firmware to the controller that makes it
behave like an I2C device in the first place -- a step that the kernel
cannot later do on its own if the firmware didn't already do it.
Skipping this initialization means the I2C controller becomes unusable
to the kernel.
This patch fixes the issue by making the i2c_init() unconditional again.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie4546c31d87d91113eeef7dc7a18599a87e6d6eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58026
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initializing SAR sensor (QUP2, address 0x988000)
BUG=b:198456205
BRANCH=None
TEST=Boot into kernel and make sure no i2c errors for 0x988000 in
dmesg
Change-Id: I75b0e9173d4c49b5e7308158a678964d6637b225
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=b:182963902
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -c max -B
Change-Id: I10f8a9682200b883474dc385331c5dae84cbdb08
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
For Herobrine variants that include a finger print sensor, we will
need to power sequence it. We are using the same FP sensor as
trogdor, so we will follow the timings used for trogdor from
CL:2695676.
BUG=b:198474942
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -c max -B
Change-Id: Ica6eafc47cf1b95eeb8d94c6e0a8c88519665e3f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58021
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ID "10029836" for machine driver, "RTL5682" for ALC5682I and "MX98357A" for MAX98360.
BUG=b:198716348
TEST=Build nipperkin, codec is functional with new machine driver.
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: Iab9d11adb7cd08effa2a9b6a627832bd89cb3cb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define SSFC bit 9-11 in coreboot for codec within ec.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:193694180
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Iba91b51cbbe7adc502372c9a026867de61d8035d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Mancomb mainboard has been cancelled. Hence delete the board support.
BUG=b:190404616
TEST=None
Cq-Depend: chromium:3188634
Change-Id: I3ce02efb1fa5ea488447099abe08da6051fb6fc6
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add ADLP 242 sku PLx related settings, which follow the settings of
ADLP 282 sku (both are 15w).
BUG=b:201253904
TEST=USE='fw_debug' emerge-brya intel-adlfsp coreboot chromeos-bootimage
Change-Id: If9b60893ab3e2c4a88e7d2cf45223c5fbce6f847
Signed-off-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The voltage rail discharge times have been measured, so therefore
the boot time on a cold boot when the CSE must go through a global reset
and thus a trip to S5 can be optimized. Select the lowest applicable
value for each PchPmSlp UPD that can be used with these measurements.
This is programmed in the baseboard because the measured discharge times
leave (what should be) plenty of margin for variants to also not violate
any power sequencing guidelines from the PDG.
BUG=b:184799383
TEST=verified time in S5 during a global reset is ~1s instead of 4s
Change-Id: Ia373c47b3967d68ddac21707c6eb4565d9d6519e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Support for drawcia_legacy board is cancelled. Hence remove the board
support.
BUG=b:192256341
TEST=None
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I76cd3e388439f5aee94a17fe35ae210f449cfbfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Support for Boten_legacy board is cancelled. Hence remove the board
support.
BUG=b:192256341
TEST=None
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: If26dc869ff95dff70c0f83a13f6f727aa5992dbd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Wheelie variant board has been cancelled. Remove wheelie variant board
support.
BUG=b:192256341
TEST=None
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3ad5bc1c987feb55183a663937794781c7301a48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Cappy variant is cancelled. Hence delete the cappy variant support.
BUG=b:192256341
TEST=None
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: If43188a3e6bf4f4449c7e2d08be7609efe58dca1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
NVMe needs extra time to run boot process, enable power and deassert
reset for NVMe earlier in the boot flow that taeko can successfully
boot into OS with non-serial coreboot.
BUG=b:199969366 & b:200711149
TEST=Build FW and test with non-serial FW reboot 20 times pass.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I032c5b90fb2148c4075d6ead3e4161c0cc659b20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add wifi sar for magma.
Due to fw-config cannot distinguish between magolor and magma.
Using sku_id to decide to load magma custom wifi sar.
BUG=b:192423859
TEST= emerge-dedede coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Iac15e958e61be6e3c136fb9be18b4695823ad1c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update PL1 min and max values to 6 W for Galith/Gallop systems.
BUG=b:201010771
BRANCH=None
TEST=Build and verify on Galith/Gallop system
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I0dfda3c2c830a2ce203668431f396859e782aa3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
For the next build phase, modify the HID of the speaker amp to
MX98360A.
BUG=b:199098681
BRANCH=none
TEST=build coreboot without error
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I0c318464fca7d35bbffd7ea0f5694b83acedff0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Refactor DPTF section of code under the kracko overridetree. This makes kracko override dptf section of dedede/baseboard, because the DPTF tool's CRT, PSV and TSR3 settings are different than expected.
BUG=b:187482019
BRANCH=dedede
TEST=Built and tested on dedede system
Change-Id: Iacc543f961a7f4652ee8583920b1794f916c7ec9
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Move max98373 amp ACPI info to I2C0 according to kano's schematics version KANO_MLB_Proto_0811.
BUG=b:192370253
TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I8f7a7938dd407666e0104ba64b22da85216a145f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
SSD sometimes can't be detected in in warm/cold boot stress.
M.2 spec describes SSD_PREST should be sequenced after power enable.
BUG=b:199822704
TEST=SSD was always discovered in warm/cold boot stress.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If0a9e36cda4dc91bbccec02f39ccb9b658d24056
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update the DPTF parameters received from the thermal team.
BUG=b:188596619
TEST=emerge-ambassador coreboot
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I081963b97ed2dae0f5d026f6443c954b52347a8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57919
Reviewed-by: Joe Tessler <jrt@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move includes using library paths to the top and remove unnecessary
comments.
Change-Id: Id26d9dfc3822b9120360fc2cb2ced8d67345a659
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add the relevant memory configuration of beetley to the blipper coreboot code
The memory parts being added are:
1. Micron MT53E512M32D1NP-046 WT:B
2. Samsung K4U6E3S4AB-MGCL
3. Hynix H54G46CYRBX267
BUG=b:200000608
TEST=emerge-dedede coreboot
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I0b04f64cb007a58ae98f5ed187feb4859a43b1b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57670
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
guybrush does not have a light sensor, do not include ACPI0008
ACPI device (Light sensor that will be managed by acpi-als IIO
kernel driver).
BUG=b:200823325
TEST=Check on Guybrush360 the sensor is not presented.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: Id1dcb3a01ee43f780e4b118d88a0351e4c543f5a
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
This change config the DRAM speed to 3733 for primus.
BUG=b:200752480
BRANCH=none
TEST=Verified that `dmidecode -t17` shows the correct
configured memory speed
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I2f3a9489dddcf102b0ffc71eb9cdab6ad38d1391
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change replaces the device tree walks with device pointers by
using alias for following devices:
1. audio_rt5682
2. xhci0_bt
3. xhci1_bt
4. acp_machine
5. i2c2
Change-Id: I56921ab54716e4d771d9de1a479f191ca5657eba
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
AMD Firmware tool allows configuring the directory table level in which
the binaries have to be added. This helps to achieve space and boot time
savings.
BUG=b:195329409
TEST=Build and boot to OS in Guybrush. Achieve a boot time savings of
~75 ms and space savings of ~600 KB per RW section.
Change-Id: Idc212b8c4f8aacfb0132983a8055f1e97af42983
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bao Zheng <fishbaozi@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Enable SaGv support for taeko
BUG=b:198548214
TEST=FW_NAME=taeko emerge-brya coreboot
Flash fw into DUT and can boot successfully
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I580a12ca511d8cde6fee1079e39e6976202da4d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Due to the vGPIO is not set correctly, without setting those pins for PEG60,
CPU cannot communicate with PCH about the clkreq state.
BUG=b:200886824
TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I6adf73103ecb02c67d9a199e13d2ead9b8b2276f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable EC keyboard backlight for kano.
BUG=b:192370253
TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I7f56b92b60cadf72eb02fd8bcb87baf36acc16e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable SaGv support for kano
BUG=None
TEST=FW_NAME=kano emerge-brya coreboot
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ifc537a5137f5e6eb10cd4c160923ea4da1f6b0d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add DA7219 codec support in maglet.
BUG=b:198239769, b:196193562
TEST:emerge coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I52d980ed611b3fbe4892cd3e65e3b35931feaba5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This brings the AMD SoC GPIO code in line with the Intel SoC code and
removes the not really needed suffix.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie2dbec81dfe503869beb2872b01a7475e2b88b33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Use the same function name as in soc/intel for this functionality. This
also brings the function name more in line with the extended version of
this function gpio_configure_pads_with_override which additionally
supports passing a GPIO override configuration.
This might cause some pain for out-of-tree boards, but at some point
this should be made more consistent, so I don't see a too strong reason
not to do this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I88852e040f79861ce7d190bf2203f9e0ce156690
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add two thermal sensors for fan and charger for DPTF based thermal
control.
BUG=b:199180746
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I1529dd5dff3445dd499ed665386a9b06d67c7028
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57833
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add vmon-slot-no,imon-slot-no and dsm_param_file_name in overridetree.cb
BUG=b:197701952
TEST=build and check SSDT
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ie646360c4ebbf25762b374c5bc3ef2017989fb2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57832
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:191776301
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Iafcbb3ce33cd2299ff98b54b9200f3e70929fb1f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57821
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The variant creation script creates a placeholder file called
mem_parts_used.txt, with the intent that variant owners will populate
this file with memory parts as needed. But instead, some partners have
been adding the parts in a new file called mem_list_variant.txt and
removing the placeholder file. E.g. https://review.coreboot.org/55735.
There's nothing wrong with this, but it's confusing to have two
different file names which serve the same purpose. Bulk rename all the
mem_list_variant.txt files to mem_parts_used.txt. The only time these
file names are used is as an argument to the spd_tools part_id_gen
script, so no other changes are necessary.
BUG=None
TEST=Re-run part_id_gen for all variants of
brya/volteer/dedede/guybrush/zork. Check that the only change is to the
"Generated by" comment in Makefile.inc and dram_id.generated.txt.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Icdeee78ae5c01e97f66c759c127175b4962d5635
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The copano and collis variants have both a mem_parts_used.txt and a
mem_list_variant.txt. The mem_parts_used.txt files are empty, so delete
them.
BUG=None
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ia98aad7238b0173b8d5c048d89637bc297d02283
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all zork variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for dalboz:
util/spd_tools/bin/part_id_gen \
PCO \
ddr4 \
src/mainboard/google/zork/variants/dalboz/spd \
src/mainboard/google/zork/variants/dalboz/spd/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/zork -a -x --timeless
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I305a24f9345bab28ff35e317b6e7fd7efba22413
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57772
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The moonbuggy pcie topology is the same as genesis so copy from its
device tree and gpios in order to enable these devices.
BUG=b:199746414
TEST=lspci
Change-Id: I4e916a95047b9f955734f164d7578c520478f5af
Signed-off-by: Jeff Chase <jnchase@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Based on latest shcematic to update the device tree and gpio.
BUG=b:197850509
TEST=FW_NAME=anahera emerge-brya coreboot
Change-Id: I0a999de479c7b2e4776a57e1e56b1568450ec31a
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all guybrush variants
to use this new location. The contents of the new SPDs are identical,
only their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for guybrush:
util/spd_tools/bin/part_id_gen \
CZN \
lp4x \
src/mainboard/google/guybrush/variants/guybrush/memory \
src/mainboard/google/guybrush/variants/guybrush/memory/mem_list_variant.txt
For dewatt, the Makefile.inc was manually modified to use the new
placeholder value.
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/guybrush -a -x --timeless
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I48ca430b80b892d68dad582b1d9937a9edafa5d4
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all dedede variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for cret:
util/spd_tools/bin/part_id_gen \
JSL \
lp4x \
src/mainboard/google/dedede/variants/cret/memory \
src/mainboard/google/dedede/variants/cret/memory/mem_parts_used.txt
For cappy, the Makefile.inc was manually modified to use the new
placeholder value.
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/dedede -a -x --timeless
Change-Id: I2871ff45d6202520d4466b68a4d5bb283faf2b63
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently, trying to regenerate the galtic Makefile.inc and
dram_id.generated.txt using part_id_gen fails due to duplicate fixed IDs
in the mem_parts_used.txt file.
Remove the fixed IDs since they aren't needed. The part IDs assigned are
the same either way.
Also delete the comments from mem_parts_used.txt, since lp4x/gen_part_id
currently doesn't support comments.
BUG=b:191776301
Regenerate the Makefile.inc and dram_id.generated.txt using gen_part_id,
and check that the part IDs don't changed. Command used:
util/spd_tools/lp4x/gen_part_id \
src/soc/intel/jasperlake/spd \
src/mainboard/google/dedede/variants/galtic/memory \
src/mainboard/google/dedede/variants/galtic/memory/mem_parts_used.txt
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ida83814b2f19b4a56eb9fde5939fa6c7874803c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all volteer variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for voema:
util/spd_tools/bin/part_id_gen \
TGL \
lp4x \
src/mainboard/google/volteer/variants/voema/memory \
src/mainboard/google/volteer/variants/voema/memory/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using:
abuild -p none -t google/volteer -a -x --timeless
Change-Id: Ibd4f42fd421bfa58354b532fe7a67ee59dac5e1d
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
SPD files are being moved from the soc and mainboard directories to a
centralised spd/ directory. This change migrates all brya variants to
use this new location. The contents of the new SPDs are identical, only
their file paths have changed.
The variant Makefile.inc and dram_id.generated.txt files were generated
using the part_id_gen tool. E.g. for anahera:
util/spd_tools/bin/part_id_gen \
ADL \
lp4x \
src/mainboard/google/brya/variants/anahera/memory \
src/mainboard/google/brya/variants/anahera/memory/mem_parts_used.txt
BUG=b:191776301
TEST=Check that each variant's coreboot.rom is the same with and without
this change. Built using: abuild -p none -t google/brya -a -x --timeless
Change-Id: I08efe1d75438c81161d9b496af2fa30ce6f59ade
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable programming of Type-C AUX DC bias GPIOs.
BUG=b:199833078
TEST=Verify that a Type-C monitor works when connected in both
orientations.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I4f6d80a9f2fc8cdc93226d6c234b54e5db830d71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update codec/amp setting.
1. Update hid for ALC5682VS
2. Add maxim properties.
BUG=b:197076844
TEST=build and check SSDT
Change-Id: I8bedd4d0737caf46769ad27bce1768c225ce8a82
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The current power sequencing for the SSD does not work in a non-serial
enabled BIOS image. It appears that the FSP scans the PCIe RPs before
the SSD has time to prepare itself for PCIe, so the FSP disables the RP
and so depthcharge cannot find a boot disk.
Changing the power sequence timing to enable power in bootblock and
deassert reset in ramstage follows the SSD's power sequence and
allows it to be discovered by the FSP so the RP does not get disabled.
BUG=b:199714453
TEST=build, boot into SSD, and run reboot stress test.
Change-Id: I5e7943a6cc88bc02bcbd97a1086b2d8044d7b1c3
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This implements qup spi driver for qualcomm chipsets
Rename header file names for trogdor to prevent breakage.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I2f2b25b6661fcd518f70383da0c7788c5269c97b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55953
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
copy existing I2C driver from /soc/qualcomm/sc7180 to common folder.
This implements i2c driver for qualcomm chipsets
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I16e6fc2c1c24b9814d1803bffd5cfbb657201cfb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Load GSI FW in ramstage and make it part of RW
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I3d9caa0921fcf9ad67f1071cdf769a99fb6d1a30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Loading QUP FW as per herobrine and piglin configuration
for I2C, SPI and UART.
As part of the code clean up, update the header files of the
QUP drivers with the correct path.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: Ic218c6a91ffc4484830446d707d1f3403e2dc46b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
BUG=b:191776301
TEST=dewatt build no longer fails when a check for non-existent files
in LIB_SPD_DEPS is added (following commit).
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Iee0c5e8b71f7cc7c016a38a60569daff99a55027
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove the override in guybrush devicetree that configured in-band eSPI
alerts. This will result in guybrush using dedicated open-drain eSPI
alerts. Guybrush boards must be reworked to connect the eSPI alert line,
otherwise they will not boot with this change
BUG=b:198596430
TEST=Boot on reworked guybrush
BRANCH=None
Change-Id: I185eec773336fb662d9fe7f4c11991813e4d7cd6
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57778
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD support for DDR4 memory part
BUG=b:199469240
TEST=none
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ie67cf6b90304f0bcf80838866c7461c0cea86dc3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
