| Age | Commit message (Collapse) | Author |
|---|
|
This will allow dropping the pointer inside romstage_params.
Change-Id: I536225351a0353298381c16cff25f39098c19bba
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Instead of passing around a pointer to an array, just write the relevant
registers directly. Note that intel/baskingridge used spaces to indent
line continuations and had to be replaced with tabs to quell Jenkins.
Change-Id: Ifa06a2ab24da9b8c6aac6480542fa32d04f6d6fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This reduces the differences between Bay Trail and Braswell.
Tested with BUILD_TIMELESS=1, Google Ninja remains identical.
Change-Id: I3d4c1285bdc4b061383b7bb6262f69671166b9c4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
This change drops the selection of VARIANT_SUPPORTS_PRE_V3_SCHEMATICS
for Vilboz since it did not have any build with pre-v3 schematics.
Change-Id: I3919ad43e1dae95a4fa71073e83865e92f30dfec
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43225
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds following two helper functions:
1. variant_uses_v3_schematics() - Check whether the variant is using
v3 version of schematics.
2. variant_has_active_low_wifi_power() - Check whether the variant is
using active low power enable for WiFi.
In addition to this, Kconfig options are reorganized to add two new
configs - VARIANT_SUPPORTS_PRE_V3_SCHEMATICS and
VARIANT_SUPPORTS_WIFI_POWER_ACTIVE_HIGH. This allows the helper
functions to return `true` early without checking for board version.
Eventually, when a variant decides to drop support for pre-v3
schematics, it can be dropped from selecting
VARIANT_SUPPORTS_PRE_V3_SCHEMATICS. Similarly, when the variant
decides to drop support for active high power enable for WiFi, it can
be dropped from selecting VARIANT_SUPPORTS_WIFI_POWER_ACTIVE_HIGH.
Change-Id: I62851299e8dd7929a8e1e9a287389abd71c7706c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43224
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves the configuration of GPIO_137 to happen in ramstage
since there is nothing in coreboot that requires the state of write
protect GPIO for zork.
Change-Id: Ibaf8e7d9dd5d13a9b39b10ac0174de345b8380f5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43223
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change removes "write protect" entry from the list of GPIOs
shared with depthcharge as done for other Chrome OS boards in CB:39318.
Change-Id: Ibd39e8d6835e465b2ab5eebcc245e45db5d84deb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43222
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Comments stating that this was mainboard-specific were very wrong.
Change-Id: I7026ca9c7dabd01b4a0c0549b697e006d5f75eb8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There's no need to repeat the same values over four variants.
Change-Id: Ifc4a9961fe9c87f15a6039e6e478682fab5b0bb7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Finally enable psp_verstage for zork.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: If6a12c2074d7c84c0cb766393c66f5eff29a58d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
1. Enable HDA Pci device in devicetree
2. Enable I2C4 in devicetree and fill ACPI information
3. Pass correct IRQ GPIO for headset jack
BUG=None
BRANCH=None
TEST=Audio playback and recording works on Waddledee.
Change-Id: I77aaa27bb29460ef834c3dd090ced868f2e99616
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41765
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:155002684
TEST=build drawcia, and check touchscreen can work
Change-Id: Ib6a190d2f6fc5132af0e58c6df9919381e88f699
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:155002811
TEST=build drawcia, and check touchpad can work.
Change-Id: I674236aa6937a0444a85e6b8e2fb9a7925b56f5c
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42922
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a new variant called Pompom that is identical to Lazor
for now. Also reorder variants alphabetically while we're here.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I5a0f297413765bce8353d5a781f0f67446de4e7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Update GPIOs since Vilboz hardware design
follow schematic V3.2, so gpio.c is unnecessary.
BUG=b:157744136
BRANCH=NONE
TEST=flash the bios to vilboz DUT and test touchpad function
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I575f8b233b56185f3281ad7127bc274bda5ea801
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42986
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
At this moment, Vilboz board version is 1 and it
according to v3+ schematics, however WiFi power enable
is active high. This change sets
VARIANT_MIN_BOARD_ID_V3_SCHEMATICS for Vilboz as 1
and VARIANT_MIN_BOARD_ID_WIFI_POWER_ACTIVE_LOW as 2.
BUG=b:160547115
BRANCH=None
TEST=flash the bios to vilboz DUT and test WIFI module
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I9699bb839a801ab7d14c38b971ec28e3a322a997
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Windows definition
There was a review comment for Chromium Linux ov2740 driver that
Windows driver already set the HID as INT3474 and suggested to have
the same value for Chrome.
The upstreamed Linux driver code has INT3474 as HID and this patch is
to set the same HID in ACPI configuration.
https://patchwork.kernel.org/patch/11540753/
BUG=b:160334865
BRANCH=none
TEST=User-facing camera should work with the driver which set the HID
as INT3474
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I10e98d32899f31d91c1cc7ddfa099af73d8aef37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43006
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Volteer world-facing camera has a privacy LED and it is supposed
to be turned on only when the camera is being used. But the LED
is always on and this is to fix the issue.
RCAM_SNR_PWR_EN (RearCAMera_SeNsoR_PoWeR_ENable) GPIO, which
controls the world-facing camera LED, was not in the power-up
and power-down sequence definitions and this caused the issue.
BUG=b:160341981
BRANCH=none
TEST=Build and boot volteer proto 2 board. Start a camera app
and check the world-facing camera LED is only turned on only when
the camera is working.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I564690baffddfdd0f998525992643aaf16ba4b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42985
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
update telemetry value for SDLE test result.
BUG=b:152922299,b:152369472
TEST=emerge-zork coreboot
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I14d218243931271ba15ec4113e9bc46c670fb2ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42999
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on schematic and gpio table of terrador, generate gpio settings
and overridetree.cb for terrador.
BUG=b:156435028,b:151978872
TEST=FW_NAME=terrador emerge-volteer coreboot chromeos-bootimage
Verify that the image-terrador.bin is generated successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4bf9081b034bc4cd566dde45586be8309cdbb4a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42302
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds memory parts used by variant terrador to
mem_list_variant.txt and generates DRAM IDs allocated to these parts.
Added memory
1. MT53E512M64D4NW-046 WT:E
2. MT53E1G64D8NW-046 WT:E
BUG=b:159195585,b:152936481,b:156435028
TEST="emerge-volteer coreboot chromeos-bootimage", flash terrador and
verify terrador boots to kernel.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ia14f76e9cb0df64961d46f4b61b39439e56f6a8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41995
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Diffentiate Lazor and trogdor build configuration
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I3ad413ea6e658e939796bebdff8c1e0dd76417cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42730
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable HotPlug for the PCIe root port that the SD express is on so the
OS can re-train the link without needing a reboot if it goes down
unexpectedly at runtime.
BUG=b:156879564
BRANCH=master
TEST=enable HotPlug on Volteer Root Port 7 (SD express) and check in
linux that it is identified as a HotPlug capable root port
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: Ie9d427dd297567f06123119a670b5ed2e1f73701
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42897
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CB:43090 renamed con to conn to avoid issues when building on Windows.
CB:42905 introduced more uses of the old name.
Adapt the latter to comply with the former.
Change-Id: I723141add5452fc541f67cb8591793f2d64cc231
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43141
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on schematic and gpio table of voxel, generate gpio settings
and overridetree.cb for voxel.
BUG=b:157879197,b:155062762
TEST=FW_NAME=voxel emerge-volteer coreboot chromeos-bootimage
Verify that the image-voxel.bin is generated successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I49c1923e63d87f11de362fd893905ac2f1137bba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Currently, the telemetry settings are not for the pollock platform
and might causethe power and performance issue. so applied the Pollock
reference board settings to Dalboz to improve the performance,
and the values need to be updated after the SDLE test finished.
BUG=b:157961590,b:152922299
TEST=Build.
Change-Id: I0da5b81afaa5814c13ec0257dc0eb3471be94c29
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2228257
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42998
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Apply the default USB2 phy tuning parameter for Zork family
BUG=b:155132211
TEST=Build, verified the default value been applied on trembyle
and the USB2 device works well.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I1f00b04173796d70147e232bafa405487b0761e1
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2260216
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42997
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The USB-C SBU and HSL orientation configuration depends on the USB
daughterboard used on the system. This patch adds an additional
configuration for supporting passive USB daughterboards using "probe"
directives to select the appropriate configuration at runtime.
BUG=b:158673460
TEST=verified active USB DBs enumerate at USB3 speeds in linux
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Change-Id: Ia4bd97de8f974531f97469a5e47ecf4d948beca9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Upcoming builds of boten will use 16 MiB SPI ROM. So create a legacy
Boten variant to support the builds that use 32 MiB SPI ROM.
BUG=None
TEST=Build the boten and boten_legacy variant.
Cq-Depend: TBD
Change-Id: Idf7732768aa7fbf2281a4cbf47b7b5b4f8ef51da
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Upcoming builds of drawcia will use 16 MiB SPI ROM. So create a legacy
Drawcia variant to support the builds that use 32 MiB SPI ROM.
BUG=None
TEST=Build the drawcia and drawcia_legacy variant.
Cq-Depend: TBD
Change-Id: Ifb5a4778abe38a396e35963a3270b0d3cc9809e0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change drops the check for ENV_RAMSTAGE in mainboard_ec_init()
since it is included only in ramstage. Also, the content of
ramstage_ec_init() is moved into mainboard_ec_init().
Change-Id: I282fb07a80f4de6064a544f6dd58e8f973a597b9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43118
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
mainboard_ec_init() does nothing in any stage other than ramstage. So,
this change drops the call to mainboard_ec_init() from
romstage.c. Additionally, it also drops ec.c from romstage and
verstage.
Change-Id: Iae0be4d678b0780cf532000a6c0fff1bce333c0e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43117
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the function `variant_romstage_entry()` which is
unused on zork.
Change-Id: I140ab3e837971c4c7dbef5d27616043b5fc6c2c9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43116
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the inclusion of codec.asl in DSDT for `GOOG0013`
device and instead uses the newly added Chrome EC audio codec driver
for filling in the device node in SSDT.
TEST=Verified that following node gets generated:
Scope (\_SB.PCI0.LPCB.EC0.CREC)
{
Device (ECA0)
{
Name (_HID, "GOOG0013") // _HID: Hardware ID
Name (_UID, One) // _UID: Unique ID
Name (_DDN, "Cros EC audio codec") // _DDN: DOS Device Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
}
Change-Id: I3e626ce01a3735ac2c966c0e95310be4c828b241
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43042
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops H1_PCH_INT macro for GPIO_9 since it is the same
across all variants. Also, the name differed from the schematics
version `H1_PCH_INT_ODL` creating confusion.
Change-Id: I7b038426a984d8abc460a0da3ee1dc5559d7ad5f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I11b02cc5f8b59559443329fe0c49a6fb82b7862a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41726
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For historical reasons, Windows has issues with certain names being
used for files and directories, 'con' or 'CON' being one of
them. Therefore, rename the pmc_mux/con driver to pmc_mux/conn in
order to work around this issue.
TEST=built volteer (only user of this driver as of now)
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ia78dc4efe647c96a7169a3b95fc3b8944d052c83
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
BUG=b:158140797
TEST=build and boot volteer with CSE Lite SKU
Cq-Depend: chrome-internal:3100721
Change-Id: I4f939883617a1271b30c76d41e61113bbdd6ab5b
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42070
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The eSPI polarity macros were reversed. Those are fixed so adjust
the corresponding values related to the correct expectations of
the IRQ path: eSPI virtual wire IRQs are active level high. The EC
sends active level high virtual wire IRQs. The default interrupt
encodings in ACPI for P2/S devices are active edge high. Therefore,
there is no need to override anything.
BUG=b:157984427
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia28d82cd9e432df98839f68bac4eae4447455e53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
V.2: Spare USB routed internally to another peripheral and so
no plug event hook needed.
BUG=b:1603699358,b:157479891
BRANCH=none
TEST=none
Change-Id: Ideacac417a46b96f3e82b53bbb341ecce79ee420
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42994
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:160296662
BRANCH=none
TEST=none
Change-Id: I5298e1779461995a98722099b397692351767089
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42975
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:160295948
BRANCH=none
TEST=none
Change-Id: I3600340d3448457942c827a463b458b280fea19a
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
BUG=b:160296661
BRANCH=none
TEST=none
Change-Id: Id5a03f2cbdca2723ab1882c619d2d34387996b27
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42973
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:160296325
BRANCH=none
TEST=none
Change-Id: Iffa6997029d0babfd6dd504a6cc212bd74de3a8f
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42972
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves the generation of I2SM ACPI device from static asl
file to runtime generation by ACP device driver. dmic_select_gpio is
set to match version 3+ of Trembyle and Dalboz schematics. In order to
maintain backward compatibility, dmic_select_gpio is updated at
runtime using variant_audio_update for board versions that are prior
to version 3 of reference schematics.
The only difference from static generation is that the device I2SM is
added under ACPD (i.e. ACP device) instead of CREC (Chrome EC
device). It does not make any functional difference from the kernel
perspective.
BUG=b:157603026
TEST=Verified that the following device gets generated in SSDT:
Scope (\_SB.PCI0.PBRA.ACPD)
{
Device (I2SM)
{
Name (_HID, "AMDI5682") // _HID: Hardware ID
Name (_UID, One) // _UID: Unique ID
Name (_DDN, "I2S machine driver") // _DDN: DOS Device Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x000D
}
})
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x01)
{
Package (0x02)
{
"dmic-gpios",
Package (0x04)
{
\_SB.PCI0.PBRA.ACPD.I2SM,
Zero,
Zero,
Zero
}
}
}
})
}
}
Verified audio via speakers and mic input.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I5d1602c7f719eef9487ddea68e429d27408f9a76
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2253638
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Modify DPTF parameters for faffy from thermal team.
BUG=b:160292247
BRANCH=None
TEST=emerge-puff coreboot chromeos-bootimage
verify the parameters are correct
Change-Id: Ie8290f5460838f785a587c85b2ab7dd171dd0a54
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
Currently, EC wake signal (GPIO_24) is configured early on in
romstage. However, there is no need for that since EC wake is not
really required to be configured until ramstage. This change moves
GPIO_24 configuration to happen in ramstage.
BUG=b:159832123
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I6949dcd7c866df2fa028c7b2e7f347cec988e309
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42952
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the pad configurations for wake lines as
follows:
1. Pen eject wake signal needs to be configured as PAD_WAKE i.e. wake
using GPIO controller block. This is because pen eject signal is not
dual routed and the trigger filtering is set by the kernel driver
differently for S0 and S3 wake. Hence, it cannot use SCI GEVENT and
instead has to fall back to using GPIO controller wake.
2. All other wake signals (EC, trackpad, fingerprint) need to be
configured as SCI. This allows OS to enable/disable wake from these
sources if required. Example: powerd disables wake from trackpad when
in tablet mode. Hence, all other wake sources use SCI.
BUG=b:159832123
TEST=Verified wake using pen eject and EC.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Id8cd5926f223db51a689ed8948040b8070cf1680
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42951
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set tcc_offset value to 10 in devicetree for Thermal Control
Circuit (TCC) activation feature.
BUG=None
BRANCH=None
TEST=Built for dedede platform and verified the MSR value
Change-Id: I53d1bd413c64643cf8bdaef266bde25a2f3a97ee
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42906
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for pen insert/eject operations in S0 and
wake on pen eject from S3 for morphius.
BUG=b:158814699,b:158719244
Change-Id: I3530a0aa83ec69559436687205c64524b862799b
Signed-off-by: Kevin Chiu <kevin.chiu@quanta.corp-partner.google.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops macros for GPIOs which are unused or don't really
require extra indirection (same across all variants).
BUG=b:159283649
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I1a94327103a419f26b1d7feda4c995363ada7281
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Board version 3 for Ezkinil follows Trembyle reference v3.51
schematics and hence GPIO_86 does not need a variant specific override.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7e04baad976f94d0d94e7196f0408c3c3237b2da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops GPIO_27 configuration for trembyle reference boards
since it is unused.
BUG=b:159453643
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I57dd78e8abcc61802ca85158e7ff348460ad1d8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
A late change went into v3+ of reference schematics which inverted
EN_PWR_WIFI to meet PCIe reset/power timings for WiFi device. This is
incorporated into v3.51+ for Trembyle reference and v3.2+ for Dalboz
reference. However, some variants are built with v3+ reference
schematics, but without the inversion of EN_PWR_WIFI polarity. Thus,
we need to add support for following combinations:
1. Pre-v3 Schematics
2. V3+ Schematics
3. V3+ Schematics + Active low wifi power
This change adds a new Kconfig
`VARIANT_MIN_BOARD_ID_WIFI_POWER_ACTIVE_LOW` that sets the minimum
board ID that has EN_PWR_WIFI active low in hardware. Variants that
missed this change in V3+ integration (berknip and vilboz) have board
IDs set to VARIANT_MIN_BOARD_ID_V3_SCHEMATICS + 1. For others, this
defaults to VARIANT_MIN_BOARD_ID_V3_SCHEMATICS.
BUG=b:159749536
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib8da7fba5f4a518a51b203d6a01a9551e261d8b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change moves variant_sleep_gpio_table() definition to dalboz and
trembyle references to allow each to make their own changes.
BUG=b:159749536, b:159453643
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I15b19cea05f1a540c56b6bc0507306d2348ac17f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change moves PCIE_RST1_L deassertion to happen as part of
variant_pcie_power_reset_configure() instead of
variant_romstage_entry() since romstage is guaranteed to run 100ms+
after PP3300_NVME is enabled. This is one of the first things that
coreboot on x86 does as part of early mainboard configuration.
Additionally, this change also drops deassertion of PCIE_RST0_L on bid
1 for dalboz since PCIE_RST0_L is already deasserted much earlier in
the boot flow.
BUG=b:152582706
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib734aa6ff664268e68388b1997ddce676504f8d2
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2261996
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Aaron Durbin <adurbin@google.com>
Tested-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change configures GPIO_40 (NVME_AUX_RESET_L) as drive low in
sleep path so that the PERST# to NVMe device keeps asserted until
coreboot reconfigures it as high on S3 resume path. This is similar to
the earlier change for PCIE_RST1_L but helps platforms that use
NVME_AUX_RESET_L instead of PCIE_RST1_L. GPIO_40 lives in S5 domain,
hence it retains state across S3 entry/exit.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ie79e946eee8f393863630226ae2183e653030415
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2261117
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change configures PCIE_RST1_L as GPO driven low on the sleep
path. This is required to keep PERST# asserted to devices until
coreboot deasserts it on S3 resume path. Without this change, on S3
resume, PCIE_RST1_L gets deasserted sooner than required resulting in
violation of PCIe reset timings.
With this change, the behavior of PCIE_RST1_L is as follows:
1. GPIO27 is configured as NF (PCIE_RST1_L) in coreboot
bootblock/romstage and driven high.
2. On S3 entry, GPIO27 is configured as GPO driven low.
* Boot out of G3: Timing should be met since GPIO_27 is pulled down by
default until coreboot configures it.
* S3 resume: Timing should be met since GPIO_27 is configured as GPO
low and it retains state across S3 entry/exit. So, should be low
until coreboot configures it.
* Warm reset: Timing should be met since it is configured as NF. So,
hardware guarantees the reset timing as seen in "warm reset.jpg" in
#46.
BUG=b:152582706
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ia0ad1522edc438fd054d927ef4a2ab5c27329c00
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2261116
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change turns off power to camera and pen devices when entering
sleep since they do not act as wake sources in S3. Power to trackpad
and WiFi is left enabled since they are wake sources for S3.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I21bcdd53370372c7d43c3b685abb2a9171e42d22
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2261115
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds support to configure GPIOs on the sleep path. This is
required to turn off power to devices that do not act as wake sources
and to assert reset to devices.
Currently, variant_sleep_gpio_table() returns an empty table by
default. In the following changes, entries will be added to
gpio_sleep_table.
BUG=b:152582706
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7286cbf165024bdd81f8748e525542dce8dd8702
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2253642
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Override VBT for nightfury SKU_ID = 2 to support different panel.
BUG=b:159051021
BRANCH=firmware-hatch-12672.B
TEST=Built and verified using different VBT by SKU_ID
Change-Id: I9450814aadc43cc7991457c3793f109b889186b9
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
in some m/b+BOE panel(G2 TS), G2 TS may still have chance to lost even
rst delay time already meets spec definition: 10us (minimum).
Restore G2 TS RST delay time to 50ms, we could have G2 TS working fine
on those specific m/b+BOE(G2 TS) panel.
BUG=b:159510906
BRANCH=master
TEST=emerge-zork coreboot
boot with G2 TS, make sure G2 TS is functional
Change-Id: Ic629c6c61572ab564def8893ce8d78dfb37d4590
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I7b657750b10f98524f011f5254e533217fe94fd8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
due to overridetree.cb set disable_xhci_lfps_pm = 0,
need correct condition expression to let function work.
BUG=b:155955302
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: Ia047c75611a35aafd15f2481bf64049e13d4a2ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42860
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
configuration table
Currently, for Stoneyridge and Picasso mainboards, pads that are
configured for SCI/SMI/WAKE need to have multiple entries in the
configuration table - one for PAD_GPI and other for the special
configuration that is required. This requires a very specific ordering
of pads within the table and is prone to errors because of conflicting
params provided to the different entries for the same pad. This also
does not work very well with the concept of override GPIOs where the
entry in base table is overridden with the first matched entry from
the override table.
This change updates the way GPIO configuration is handled for special
routing like SCI/SMI/WAKE/DEBOUNCE by setting the control field of
soc_amd_gpio structure in the macros performing these
configurations. Also, program_gpios() is updated to perform a write to
GPIO control register instead of read-modify-write. This is because
mainboard is expected to provide only a single configuration entry for
each pad within a given table. Thus, there is no need to preserve
earlier configuration.
Mainboards that were providing multiple entries for a single pad are
updated accordingly.
BUG=b:159944426
Change-Id: I3364dc2982d66c4e33c2b4e6b0b97641ebea27f0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42875
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
H1 is not a wake source and hence there is no need to configure SCI
GEVENT for it. This change drops PAD_SCI() configuration for GPIO_9
i.e. H1_PCH_INT_ODL.
BUG=b:159944426
Change-Id: Iec2285b76f9c5fa1b4b1be15128fea316fa04555
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:159187889
BRANCH=none
TEST=none
Change-Id: I13626a236f1b7385208c4181150f094cbda490ed
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
Set tcc_offset value to 10 in devicetree for Thermal Control
Circuit (TCC) activation feature.
BUG=None
BRANCH=None
TEST=Built for volteer platform and verified the MSR value
Change-Id: I6438547e09a3ff3a1c01addfcc01383e89f5b435
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Bring all GNVS related initialisation function to global
scope to force identical signatures. Followup work is
likely to remove some as duplicates.
Change-Id: Id4299c41d79c228f3d35bc7cb9bf427ce1e82ba1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42489
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use defines found in <cpu/x86/smm.h>.
Change-Id: Ib75df13021120fb2c056782c252e97d6b036c7da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Using proper symbols for base addresses, it is possible to
only define the symbols for base addresses implemented for
the specific platform and executing stage.
Change-Id: Ib8599ee93bfb1c2d6d9b4accfca1ebbefe758e09
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
samsung-K4A8G165WC-BCWE_x1 # 0b0101
micron-MT40A1G16KD-062E-E_x2 # 0b0110
hynix-H5ANAG6NCMR-XNC_x2 # 0b0111
samsung-K4AAG165WA-BCWE_x2 # 0b1000
BUG=b:159418772
BRANCH=master
TEST=emerge-zork coreboot
Change-Id: I24b632c75d4a0660dc6beb88f135b546860d7079
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42814
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
update telemetry to improve the performance.
BUG=b:154879805
BRANCH=master
TEST=emerge-zork coreboot
verify by Stardust test
Change-Id: Iae5486cf2ee26b3d8e6124edfff4fe2d1fbe211e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42817
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add G2 GTCH7503 HID TS support
BUG=b:159510906
BRANCH=master
TEST=emerge-zork coreboot
boot with G2 TS, make sure G2 TS is functional
Change-Id: Id9ed5fc768459edc4660ddd6fbffb0b1973ce6d1
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
update telemetry to improve the performance.
BUG=b:154863613
BRANCH=master
TEST=emerge-zork coreboot
Change-Id: Ia08259e81f360259f23ea0f9c5c128c9d0961322
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add Samsung K4A8G165WC-BCWE x2
BUG=b:159418770
BRANCH=master
TEST=emerge-zork coreboot
Change-Id: I200a1074d3c9fe79a8a2c69f42b0612e745f36f5
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add Samsung K4F8E3S4HD-MGCL DRAM support.
DRAMID: 0x8
BUG=b:145094527
BRANCH=master
TEST=emerge-snappy coreboot chromeos-bootimage
Change-Id: Ic450c4abebfeaed050a7b8fcae74b87a148dd5cd
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Due to faffy has PL-2303 connect to USB2 port6(count from port0),
needs to enable it.
BUG=b:159760559
BRANCH=None
TEST=emerge-puff coreboot chromeos-bootimage
boot on puff board
Change-Id: Icc805757b043e7fac4d05188cbf2f9c9c56c2a2e
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Both Dali and Pollock chips have less PCIe, USB3 and DisplayPort
connectivity. While Dali can either be fused-down PCO or RV2 silicon,
Pollock is always RV2 silicon.
Since we have all boards using this code in tree right now,
soc_is_dali() can be renamed and generalized to soc_is_reduced_io_sku().
Change-Id: I9eb57595da6f806305552128b0c077ceeb7c4661
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42833
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change allows mainboard to configure different wakeup routes that
can be used by a GPIO key:
1. SCI: This is selected when SCI route is used to wake the system. It
results in _PRW property being exposed in ACPI tables.
2. GPIO IRQ: This is selected when GPIO controller wake is used to
wake the system. It is typically used when the input signal is not
dual routed and the GPIO controller block is not capable of applying
filters for IRQ and wake separately. In this case, _PRW is not exposed
in ACPI tables for the key device.
3. Disabled: No wakeup supported.
Based on these wakeup routes, gpio_keys_add_child_node() is updated to
expose _PRW and _DSD properties for wakeup appropriately.
Additionally, the change updates mainboards that were already using
gpio_keys to set wakeup_route attribute correctly and renames "wake"
to "wake_gpe" to make the usage clear.
BUG=b:159942427
Change-Id: Ib32b866b5f0ca559ed680b46218454bdfd8c6457
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit 1408798637125f1707ded7215e22461c623a79a8.
Reason for revert: Causing backlight issues in device. Will reland after more debugging to figure out the root cause.
BUG=b:159370566
BRANCH=None
TEST=boot up device and make sure when kernel is booted, backlight comes up.
Change-Id: I643854c6c805d262539bbb482808e8c322059a49
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
That option is only relevant if the boards selects HAVE_PIRQ_TABLE which
it doesn't.
Change-Id: Ib5839a42f5133f5f84e1e1e4e587801b916ca571
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Currently, Reset Power Cycle Duration is set with default value (4s).
This adds around ~5 seconds of delay during power cycle or global reset.
So, this patch sets PchPmPwrCycDur (Reset Power Cycle Duration) to 1s
to minimize the delay.
Delay with Power Cycle or Global Reset:
Existing behaviour:
S0->S5 -> [ ~5 seconds delay ] -> S5->S0
With the patch:
S0->S5 -> [ ~2 seconds delay ] -> S5->S0
Also, correct the comment mentioned for PchPmSlpAMinAssert.
The value(3) defined for PchPmSlpAMinAssert triggers signal assertion width
to 98ms not 2s.
Test=Verified on Hatch and Puff boards
BUG=b:158634281
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I368c6716a92e06903a872f9e87ae0698eab95bdd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42441
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is to enable Intel ME communication interface HECI1 by
devicetree for PAVP with CSE Lite.
BUG=b:159615125
TEST=Build and boot volteer. Run lspci and check pcie device
00:16.0 Communication controller: Intel Corporation Device a0e0
Change-Id: I68eb51c6a0af77982c060767993265764a2bc926
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
due to overridetree.cb set disable_xhci_lfps_pm = 0,
need correct condition expression to let function work.
BUG=b:146768983
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I53621d7674a531adfa40e8703cb2cd01c50376b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42564
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves the configuration of PCIE_RST0_L as native
function to happen in early GPIO table. This ensures that the PERST#
signal is deasserted as soon as possible when the system comes out
of sleep state in case the sleep path asserted/deasserted the PERST#
as GPIO out.
A big difference in functionality with this change is that PCIE_RST0_L
signal is now configured as part of RO, which should be fine since
all PCIe devices have a second AUX_RESET_L signal or use PCIE_RST1_L
to control the actual reset to the device.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I21a9c25b5a8a6d502cdb79cbe0dbad6ef98d6d63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42739
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change replaces variant_wifi_romstage_gpio_table() with
variant_pcie_power_reset_configure() to handle the reset and power
sequencing for WiFi devices pre- and post- v3 version of schematics.
These are the requirements that need to be satisfied:
1. As per PCI Express M.2 Specification Revision 3.0,
Version 1.2, Section 3.1.4 "Power-up Timing", PERST# should stay
disabled until `TPVPGL` time duration after device power has
stabilized. Value of TPVPGL is implementation specific.
2. For Intel WiFi chip, it is known to get into a bad state if the
above requirement is violated and hence requires a power cycle.
3. On pre-v3 schematics:
- For both dalboz and trembyle references, GPIO42 drives
WIFI_AUX_RESET_L which is pulled up to PP3300_WIFI.
- For both dalboz and trembyle references, PP3300_WIFI is controlled
using GPIO29. This pad gets pulled high by default on PWRGOOD
because of internal pull-up. But, at RESET# it is known to have a
glitch. When GPIO29 gets pulled high, it causes WIFI_AUX_RESET_L to
be pulled high as well. This violates the PCIe power sequencing
requirements. Hence, for pre-v3 schematics on both dalboz and
trembyle, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET_L.
b. Disable power to WiFi.
c. Wait 10ms to allow WiFi power to go low.
d. Enable power to WiFi.
e. Wait 50ms as per PCIe specification.
f. Deassert WIFI_AUX_RESET_L.
4. On v3 schematics:
- For trembyle: WIFI_AUX_RESET_L is driven by GPIO86 which has an
internal PU as well as an external PU to PP3300_WIFI.
- For dalboz: WIFI_AUX_RESET is driven by GPIO29. This is active
high and has an internal PU. It also has an external 1K PD to
overcome internal PU.
- For both dalboz and trembyle references, PP3300_WIFI is
controlled by GPIO42 which has an internal PU and external
PD. Trembyle schematics have a comment saying strong PD of 2.2K but
the stuffed resistor is a weak one (499K). ON dalboz, it uses a
weak PD (which doesn't look correct and instead should be a strong
PD just like trembyle). Having a strong PD ensures that the WiFi
power is kept disabled when coming out of G3 until coreboot
configures GPIO42 as high.
- Thus, for v3 schematics, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET{_L} signal.
b. Enable power to WiFi.
c. Wait 50ms as per PCIe specification.
d. Deassert WIFI_AUX_RESET{_L} signal.
BUG=b:157686402, b:158257076
TEST=Verified that QCA and AX200 cards both continue working. Tested
QCA on Dalboz and Trembyle. Tested AX200 on morphius.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I532131ee911d5efb5130d8710f3e01578f6c9627
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42738
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the baseboard GPIO table in ramstage to match
v3 version of dalboz reference schematics. All variants using this
reference are accordingly updated to configure the GPIOs that changed
as part of v3 schematics.
BUG=b:157165628, b:157744136, b:157743835
TEST=Compiles
Signed-off-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: If9d0e35801f9f9b15eddeb4ec7068fed6d401307
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2251394
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Auto-Submit: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42725
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the baseboard GPIO table in ramstage to match v3
version of trembyle reference schematics. All variants using this
reference are accordingly updated to configure the GPIOs that changed
as part of v3 schematics.
BUG=b:157088093, b:154676993, b:157098434
TEST=Compiles
Signed-off-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib1d6ee2e995c1fca229c20ea63da9a45fb89f64a
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2251393
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42724
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates _v3 version of romstage and wifi GPIO tables
to match v3 schematics.
BUG=b:157165628, b:157744136, b:157743835
TEST=Compiles
Signed-off-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Id8b46fcb4552af6eda5b50224b0557bae37f9ebd
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2251392
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42723
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates _v3 version of romstage and wifi GPIO tables to
match v3 schematics.
BUG=b:157088093, b:154676993, b:157098434
TEST=Compiles
Signed-off-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic605559b3226e2ad9b5b3f3fa45c4aa9f9b5fe22
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2251391
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42722
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates variant_romstage_gpio_table() and
variant_wifi_romstage_gpio_table() to support v3 version of schematics
for dalboz and trembyle reference designs. gpio_set_stage_rom and
gpio_set_wifi are divided into two groups:
a) Pre-v3 (GPIO table for pre v3 schematics):
* gpio_set_stage_rom_pre_v3
* gpio_set_wifi_pre_v3
b) v3 (GPIO table for v3+ schematics):
* gpio_set_stage_v3
* gpio_set_wifi_v3
Currently, both _v3 is a copy of _pre_v3, but will be updated in
follow-up CLs to make it easier to identify what changed from _pre_v3
to _v3.
BUG=b:157088093, b:154676993, b:157098434, b:157165628, b:157744136, b:157743835
TEST=Compiles
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I444875d93100c2f2abdb6dec4312861fd89d9b78
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2251390
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42721
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
RAM_ID GPIOs are configured by ABL based on the information added to
APCB. coreboot does not need to configure these pads. This change
drops the RAM_ID configuration from trembyle baseboard. Dalboz never
really configured RAM_IDs in coreboot.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ie1dfcc3c185304d917ab4386920445ba0119ac69
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2252710
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42720
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves the GPIOs that need to be configured for early
access in coreboot to early_gpio_table[] in
gpio_baseboard_common.c. These GPIOs include:
* Pads to talk to EC
* Pads to talk to TPM
* Pads to talk to serial console
These should be configured in the first stage that runs coreboot
i.e. in case of VBOOT_STARTS_BEFORE_BOOTBLOCK, it should be done as
part of verstage (which starts on PSP), else it should be done as part
of bootblock (which is the first stage that runs on x86).
This change drops GPIO_137 from early_gpio_table since that is not
really required in early stages.
BUG=b:154351731
TEST=Verified that trembyle still boots.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ifbdbb02cbfc65ddb68f0ae75cf4b1f2ea1656b91
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2252709
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable DPTF functionality on jasperlake based dedede platform
BRANCH=None
BUG=None
TEST=Built for dedede system
Change-Id: I17b6e4e96abee6181b0d1f94c356a32aa82c19b9
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41668
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add UPD xhci0_force_gen1 for Trembyle and Ezkinil.
The default setting is set to disable, and set enabled for Ezkinil.
Trambyle -> set default as disable.
Ezkinil -> set enable by request.
BUG=b:156314787
BRANCH=trembyle-bringup
TEST=Build. Verified the setting will be applied on Ezkinil/Trembyle.
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I65d06bfe379f9e42101bfae1a02a619ee2f24052
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2216090
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1) Based on malefor schematics, disable unused I2C port, USB port, TBT
PCIe
2) Add audio device to the tree
BUG=b:150653745, b:154973095
TEST=FW_NAME=malefor emerge-volteer coreboot chromeos-bootimage
Boot to kernel and check the devices' function worked properly.
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: I9ce465705e8b8f67ddbc9e4eb06c5a8bfac65fcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42246
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the volteer2 variant of the volteer reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
Modified to alphabetize and update to duplicate latest volteer changes
currently in the review and merge pipeline.
Added the following missing files from the variants/volteer2/ folder:
- gpio.c
- include/variant/acpi/dptf.asl
- acpi/mipi_camera.asl
- Makefile.inc
- memory/dram_id.generated.txt
- memory/Makefile.inc
- memory/mem_list_variant.txt
- overridetree.cb
BUG=b:159135047
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOLTEER2
Change-Id: I987c72b83dc993af248a753a2caa56be0f26c1ad
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42605
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These are the simple cbmem_find() cases. Also drop the redundant
error messages.
Change-Id: I78e5445eb09c322ff94fe4f65345eb2997bd10ef
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Create the delbin variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:158797761
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_DELBIN
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Change-Id: Icf5fc6b9cc6a7c47e52103b2d396bcddb26adf50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
