| Age | Commit message (Collapse) | Author |
|---|
|
Volmar does not support Thunderbolt, therefore disable all of the TBT
devices in the devicetree. The volmar fit image had been disabled already, cf. chrome-internal:4459289.
BUG=b:2233193
TEST=Build and run on DUT.
Change-Id: Ic1bba80707b1d4a97c486e22f79feccf6241865e
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure GPIOs according to updated schematics.
- GPP_A21 from NC to TCP_DP1_CTRLCLK.
- GPP_A22 from NC to TCP_DP1_CTRLDATA.
- GPP_E22 from DDIA_DP_CTRLCLK to NC.
- GPP_E23 from DDIA_DP_CTRLDATA to NC.
BUG=b:214025396
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I9d2d73820fbb191b682713e4e351c6375927ddf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This sets EPP value to be 45% for all Adl RVP variants.
Historically, EPP Ratio has always been 50% (128) on Chrome platforms.
But on Intel Alderlake EPP ratio of 45% is recommended for optimal
power and performance on Chrome platforms.
TEST=
Use 'iotools rdmsr [cpu id] 0x774' command and check field 32:24 = 0x73.
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: If83a2148d596efccd2e50cc82f1afcbfb9ebb935
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
1.Change I2S GPP_Sx (S0-S3) Native PAD Configuration from NF2 to NF4
2.Select CS35l53 AMP driver for Vell variant.
Change-Id: I96d49bd1a2ba061c4fd52b450b31d0885f49552c
Signed-off-by: Shon.Wang <shon.wang@quanta.corp-partner.google.com>
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch is adding support for Cirrus Logic CS35l41/CS35l53
smart amplifier. This part is now used in number of new chromebook's
HW designs by several vendors.
This driver uses the ACPI Device Property interface to generate
the required parameters into the _DSD table format expected by
the kernel. For detailed information about these properties, please
check Linux kernel documentation:
/Documentation/devicetree/bindings/sound/cirrus,cs35l41.yaml
Change-Id: I2cbb1cef89f8d56ee73fab06c68933a2ab8c3606
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:224618411
TEST=util/abuild/abuild -t GOOGLE_SKYRIM with and without APCB
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I71b30a5716f2e0d60d07a0ec29f98609c1f2a8b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Needed so i2c communication works.
BUG=b:224618411
TEST=build skyrim
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8ec7c18cae509b5683cb73153fd6d3747cf9d753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62874
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will fix:
> [INFO ] Probing TPM I2C: tis_plat_irq_status() not implemented, wasting 20ms to wait on Cr50!
BUG=b:224618411
TEST=Compile skyrim
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5add694506ad089adcc8961f101bf507bc39a522
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62873
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
serially""
This reverts a change that was causing hangs and exceptions during boot
on an ADL brya4es.
The hang (or APIC exception) occurs at what appears to be the FSP MP
initialization sequence, prior to the "Display FSP Version Info HOB"
log being displayed :
[DEBUG] Detected 10 core, 12 thread CPU.
[DEBUG] Display FSP Version Info HOB
This reverts commit 40ca79714ad7d5f2aa201d83db4d97f21260d924.
BUG=b:224873032
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and verify brya4es
is able to successfully reboot 200 times without any issues.
Change-Id: I88c15a51c5d27fbd243478c923e75962d3f8d67d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This message is not really an error message, so BIOS_ERR is
inappropriate. The message does seem more like a warning though,
that the developer could have multiple Kconfigs selected to send EOP,
therefore switch to BIOS_WARN instead.
BRANCH=firmware-brya-14505.B
TEST=build
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I57a34334007a6a7443302c2f25de3d5c87c85573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Change-Id: I22e4a7c6385ffb9ba77e10edad41ef3d027ba694
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62906
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ibf91a879478e03b584756dc24fe33fb013803f9d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
TCSS ASL code was carried forward from TGL and it used to follow the same
sequence.
Recently as part of s0ix hang issue, it was found that sending IOM
MCTP command as part of TCSS D3 Cold enter-exit sequence created an
issue.
We discovered that due to change in hardware sequence, ADL should not
set/reset IOM MCTP during D3 cold entry or exit. This patch removes the
bit setting from ASL file to prevent hang in the system.
This patch also removes obsolete Pcode mailbox communication which is
no longer required for ADL.
BUG=b:220796339
BRANCH=firmware-brya-14505.B
TEST=Check if hang issue is resolved with the CL and no other regression
observed
Change-Id: I2f066bcc4a8f475a15ddd12ef5ed87d7298312bb
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62861
Reviewed-by: Shobhit Srivastava <shobhit.srivastava@intel.corp-partner.google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The coreboot toolchain is a huge blob and increases the size of the
build a lot. If needed, the specific toolchain can be added before
building the ISO or with `nix-shell` later in the live system, as shown
below.
$ nix-shell -p coreboot-toolchain.i386
Thus, remove this from the todo list.
Change-Id: Ia24ceb84f202828f1c97d3ba5bafbf6af0361bdb
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Some counters are not being initialized and are relying on mainboards to
set their values. If the mainboards have not implemented these
functions it leads to indeterminate behavior.
BUG=b:224987813
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I254e26080319478b1b5b1f5c353a7966cfac63b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Some counters are not being initialized and are relying on mainboards to
set their values. If the mainboards have not implemented these
functions it leads to indeterminate behavior.
BUG=b:224987813
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I14903980fd921cad24c39cadd533349c14cc1cd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Some counters are not being initialized and are relying on mainboards to
set their values. If the mainboards have not implemented these
functions it leads to indeterminate behavior.
BUG=b:224987813
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I8d4f5b1124d4017b04bcaf7044216fd696dce63d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Use C code to generate MS0X entry and provide variant hook.
BUG=b:207144468
TEST=check SSDT table has the same entry.
Scope (\_SB)
{
Method (MS0X, 1, Serialized)
{
If ((Arg0 == One))
{
\_SB.PCI0.CTXS (0x148)
}
Else
{
\_SB.PCI0.STXS (0x148)
}
}
}
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ic36543e5cbaf8aaa7d933dcf54badc5f40e8ef02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This was to merge PCIe ACPI code to WWAN device. But, now use recent
_DSD generation changes in FM driver instead. PCie generic driver is
not used for WWAN at this time.
Also, RTD3 devices are moved to overridetree.cb where WWAN is
present.
BUG=b:221250331
BRANCH=firmware-brya-14505.B
TEST=
Check that _DSD is added to WWAN device in SSDT for the variants.
Check that RTD3 is added to WWAN device in SSDT for the variants.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ia343c7545cf30bdbcd1de19e5eb84049dbb2977f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow thermal team design to update thermal table.
BUG=b:223492897
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I5da776e7ae3368ce00cd29ec0ccdb5b7a725ff88
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
For galnat platform, support 2nd ELAN touchscreen via SSFC.
Define FW_CONFIG bits 39 - 40 (SSFC bits 7-8)
for touchscreen controller switch.
BUG=b:221002826
TEST=touch screen is functional.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Id3501205b147c9dc3c96ce8381a3e7492ae8258e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
In the devicetree case where a generic device underneath the Intel PCI
CNVi device carries the device properties, the incorrect device was
passed to wifi_ssdt_write_properties.
Also while here, update the UUID for `DmaProperty` to match what
Microsoft defined here:
https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports
BUG=b:215424986, b:220639445
TEST=dump SSDT and see that _PRW for CNVi device is no longer garbage,
but contains the value from the devicetree (GPE0_PME_B0).
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iafd86458d2f65ccb7e74d1308d37fd3ebbf7f520
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
|
|
In usb4_retimer_fill_ssdt(), it search all dpf ports and shows message
in not support dpf ports.
It's not error and changes the loglevel prefix to BIOS_INFO.
BUG=b:222038287
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I508ec7662e078893f944edb3d68364c57d5c5a73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This message is not really an error message, so BIOS_ERR is inappropriate. Since the message is informational, switch to
BIOS_INFO instead.
BUG=b:222038287
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I9dc852a0cd30f95506c205f161a05e8a8c44fcd5
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62821
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
In most boards, it doesn't write OEM_NAME in CBI to override the
manufacturer name in the SMBIOS table. It' better use the "BIOS_INFO" than "BIOS_ERR"
BUG=b:222038287
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I52eb1e6926eaac30b1dbee13ab750ef15b466d89
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Modify 15W SOC default power settings for kinox.
- PL2 39W
- PL4 100W
- Psys_PL2 65W
- Psys_imax_ma 5000ma
- bj_volts_mv 20000mv
BUG=b:213417026, b:222599762
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I2956705f7d26929c7cf2dd4e852fc61b619a83e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62627
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch refactors the current P2SB common code driver to accommodate
the future SoC platform with provision of more than one P2SB IP in
disaggregated die architecture.
IA SoC has only one P2SB in PCH die between SKL to ADL. Starting with
MTL, one more P2SB IP resides in IOE die along with SoC die. (PCH die is
renamed as SoC in MTL.)
P2SB library (p2sblib.c) is common between PCH/SoC and IOE, and p2sb.c
is added only for PCH/SoC P2SB.
BUG=b:224325352
TEST=Able to build and boot brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib671d9acbfdc61305ebb401499bfc4742b738ffb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
1.Assert eMMC enable pin in bootblock
2.Deassert eMMC reset pin in bootblock
BUG=b:220821454
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I924fcdadaae8ed29b50369a55bad00983cf6ba19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change supports the configuration and enablement of
mdp clock to vote for turbo and supports different display
panel resolutions and framerates.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Change-Id: Ibf4f11d02b0edf83461dbb7af99fda5f33cd5b71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62371
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for EDP (Embedded DisplayPort) clocks in coreboot.
This change supports the configuration and enablement of
EDP PIXEL, LINK, LINK_INTF and AUX clocks.
BUG=b:182963902,b:216687885
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Change-Id: Ia6872ede515401e95ea2dadc9766e3e70fb66144
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59611
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow the latest schematic change, gpio will match the baseboard.
Return the current table as override.
BUG=b:223677877
TEST=audio is functional on board_0.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I91dc2c9c8811d403c60a4b4f3a7c5ed8de4e527e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Currently, many Linux drivers use DMI quirks to identify ChromeOS
devices and handle them accordingly: namely they look for the SMBIOS
system manufactuer to be "GOOGLE" or "Google", and the bios-vendor to be
coreboot. Historically this was consistently the case, but recent model
ChromeOS devices allow the OEM to set the mainboard manufacturer, which
is also the default system manufacturer. This breaks many DMI quirks,
notably ones used by SOF (sound open firmware) for audio.
To fix this, set the system manufactuer for ChromeOS devices to "Google"
for devices selecting CONFIG_EC_GOOGLE_CHROMEEC_SKUID, leaving the OEM
customization in place for the mainboard manufacturer. Since boards
selecting CONFIG_EC_GOOGLE_CHROMEEC_SKUID are the only ones overriding
the default mainboard manufacturer, they are the only ones which need
this correction.
Test: build/boot google/bloog with Linux 5.16, verify SOF drivers
correctly detect device as a Chromebook and load the appropriate
audio firmware.
Change-Id: I9de17fa12689ab4e627b995818aa3d2653102b04
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62796
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ADL-P MCH ID 4, 8, 9, 10 into this list.
BUG=b:222038287
BRANCH=firmware-brya-14505.B
TEST=Build and check fsp log to confirm the settings are set properly.
Signed-off-by: Curtis Chen <curtis.chen@intel.com>
Change-Id: I2cee31ba56e0b142c50a745c453968635e86296e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Cache the BIOS region and extended BIOS region if the boot device is
memory mapped, which is mostly the case with Intel SoC platform.
Having the ROM region cached helped to improve the pre-boot time.
TEST=Able to boot redrix to Chrome OS without seeing any sluggishness.
Additionally verified on EHL board (from siemens), shows significant
savings in payload loading time as below:
Here is the timestamp snippet showing the payload load time as a
comparison between current upstream and the patched version:
upstream:
90:starting to load payload 1,072,459 (1,802)
958:calling FspNotify(ReadyToBoot) 12,818,079 (11,745,619)
with this patch:
90:starting to load payload 1,072,663 (2,627)
958:calling FspNotify(ReadyToBoot) 5,299,535 (4,226,871)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I02b80eefbb3b19331698a205251a0c4d17be534c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch provides a way to cache `ext_bios` region for all stages to
save boot time.
TEST=Able to see the ext_bios region in MTRR snapshot when cached on
the Brya variants.
Here is the timestamp snippet showing the payload load time as a
comparison between current upstream and the patched version:
upstream:
90:starting to load payload 1,072,459 (1,802)
958:calling FspNotify(ReadyToBoot) 12,818,079 (11,745,619)
with this patch:
90:starting to load payload 1,072,663 (2,627)
958:calling FspNotify(ReadyToBoot) 5,299,535 (4,226,871)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I87139a9ed7eb9ed43164a5199aa436dd1219145c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch cleans up `efi_datatype.h` to allow other SoC and/or driver
code to use this file.
`PiPei.h` file only gets added from UDK2017 hence, the platform with the
older EDK2 base (prior to UDK2017) is unable to resolve this file
dependency.
This CL removed the `PiPei.h` header and only added the required header
file `PiPeiCis.h` for platforms with UDK base >= 2017.
BUG=b:200113959
TEST=Able to build Brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9177814fcf41e5950ace94050356f0273f765c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
dev->ops = &wifi_cnvi_ops need is_cnvi be true. This cause the exclusive
statement so is_cnvi never be true in !DEVTREE_EARLY.
BUG=b:224317408
TEST=no assertion in coreboot.
[EMERG] ASSERTION ERROR: file 'src/acpi/acpigen_pci.c', line 24
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I1ca6312ce164c43021686b483f6579164614cede
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:182963902,b:177917361
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I0f1dd05ee224bf8284661c0afaa01d0a9d71daa7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Move selects from Kconfig.name to Kconfig so that the configuration is
in one place and not distributed over two files.
Change-Id: I500f6422c1f8975de8b0bcc8b95cba2bcd4ebe27
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable PCIe-eMMC bridge for Kinox.
BUG=b:218786363, b:211176722
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iec34708e5879c47f5339c48fd996eb6d7ef0ee86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow the Thermal_paramters_list-0314.xlsx to modify DPTF/Fan parameters.
BUG=b:221180425, b:222020226, b:221182596
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I5f44120430029130d38b89d0eab6bbf205aca929
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
As per ME BWG, the patch retries MEI CSE DISABLE command if CSE doesn't
respond or sends the garbled response. It retries the command
additionally 2 more times.
TEST=build and boot the Brya board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Id38a172d670a0cd44643744f27b85ca7e368ccdb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
As per ME BWG, the patch retries END_OF_POST command if CSE doesn't
respond or sends the garbled response. It retries the command
additionally 2 more times.
BUG=b:200251277
TEST=Verify EOP retry mechanism for brya board.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ieaec4d5564e3d962c1cc866351e9e7eaa8e58683
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This adds the following commits:
* a069321 cezanne: Update SMU firmware to 64.62.0
* d8a51cb cezanne: Upgrade ABL to 0x22146070
Change-Id: I066252eda56b8b62db420cbcfc95c97875a3b6d1
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Remove global variable and use 'pcidev_path_on_root()' to get the base
address of PCIe controller.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ia41c82a7aa5d6e9d936e242550851cef83afeae9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add chip config for setting PCIe config.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Icff83f2a9f76862065987a74cfcc7e511be80a20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The current SMM framework only allows the mainboard code to handle GPEs.
i.e., Events 0 - 23. This change allows the mainboard code to handle any
SMI events not handled by the SoC code. This will allow the mainboard
code to handle `SMITYPE_ESPI_SMI`.
BUG=b:222694093
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I81943e8cb31e998f29cc60b565d3ca0a8dfe9cb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Rename `BOARD_HP_SNB_IVB_LAPTOPS` to `BOARD_HP_SNB_IVB_LAPTOPS_COMMON`
to indicate and to make it clear that this option serves as base for
others.
Built HP EliteBook Revolve 810 G1 with BUILD_TIMELESS=1 and also with
`INCLUDE_CONFIG_FILE` disabled. coreboot.rom remains identical.
Change-Id: Icadeb8a33ae0787d2cd5da460065a2ed15256d64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Built HP EliteBook Revolve 810 G1 with BUILD_TIMELESS=1 and
coreboot.rom remains identical.
Change-Id: I54367c7c663ad288ccdcbd4e7289546489a68f30
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Based on the schematic carbine_adl-p_dvt_20211104.pdf, the GPP_D0 is
directly connected to FP module, Set GPP_D0 to GPO, DUT can flash FP
firmware successfully.
BUG=b:222188263, b:223906569
TEST=USE="project_gimble emerge-brya coreboot" and run the Fingerprint
Firmware Test.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I164ffff6bd3b4058d6e28247eb7c3ed46d3891b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:182963902,b:177917361
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: Ieca7e9fc0e1a018fcb2e9315aebee088edac858e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59193
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch introduces CONFIG_I2C_TRANSFER_TIMEOUT_US,
which controls how long to wait for an I2C devices to
produce/accept all the data bytes in a single transfer.
(The device can delay transfer by stretching the clock of
the ack bit.)
The default value of this new setting is 500ms. Existing
code had timeouts anywhere from tens of milliseconds to a
full second beween various drivers. Drivers can still have
their own shorter timeouts for setup/communication with the
I2C host controller (as opposed to transactions with I2C
devices on the bus.)
In general, the timeout is not meant to be reached except in
situations where there is already serious problem with the
boot, and serves to make sure that some useful diagnostic
output is produced on the console.
Change-Id: I6423122f32aad1dbcee0bfe240cdaa8cb512791f
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=b:224325352
TEST=Able to build ifdtool.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3564efa27d0271286435284e745458aada987008
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
All TGL mainboards are setting DIMM_SPD_SIZE to 512. Thus, default to
512 in the SoC Kconfig and drop it from the mainboard Kconfigs.
Change-Id: I9fd947b61c984e10bd5fba20b73280b08623a008
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62766
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PCI ID's for APL/GLK so they can use HDA.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I37df388a93ffc06e716085a58d0d00ed5c6fa9e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
BUG=b:219616787
BRANCH=guybrush
TEST=emerge-guybrush coreboot
update the thermal setting value by measurement and
pass the thermal performance test
Change-Id: I3ba3ab990d5362c6f02d2ee5a023f4c5cca7fa45
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Using the GPP_F19 as privacy switch for camera in banshee.
BUG=b:223712143, b:216110896
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I67d65347ceac7152f1951018a633a2e93ee84e14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
If the DRAM part number is not available in the SPD data (meaning filled
with 0x00) do not print it in the log.
Change-Id: If7224c6e114731b1c03915a2bde80f57369d0cee
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The pmic hwcid dumping should not be a warning, so we modify it to info.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I4a930b69bd45d5f0d84c3d269ca721b287dbadea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
It's more reasonable to halt when we trigger watchdog reset because
the whole system should be reset afterwards.
BUG=b:222217317
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I726ba1599841f63b37062f9ce2e04840e4f250bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
C1-state auto demotion feature allows hardware to determine C1-state as
per platform policy. Since Brya sets performance policy to balanced from
hardware, auto demotion can be disabled without performance impact.
Also, disabling this feature results in 110 mW power savings during
video playback.
Note that C1state Autodemotion feature is not applicable for ADL-P SoC.
Hence recommendation is to keep it disabled.
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Code compiles and correct value of c1-state auto demotion is passed
to FSP. Also power and performance impact has been measure by respective
teams.
Change-Id: I41eea916cdfe4a86e4d263e3191f5cb40fa33a90
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
FSP has a parameter to enable/disable c1-state autodemotion feature.
Boards/Baseboard can choose to use this feature as per requirement.
This patch hooks up this parameter to devicetree
BUG=b:221876248
BRANCH=firmware-brya-14505.B
TEST=Check code compiles and correct value has been passed to FSP.
Change-Id: I2d7839d8fecd7b5403f52f3926d1d0bc06728ed9
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
coreboot chip.h files mainly contains variable which allows board to
fill platform configuration through devicetree.
Since many of this configuration involves FSP UPDs, variable names were
in camel case which aligned with UPD naming convention.
By default coreboot follow snake case variable naming, so cleaning up
file to align all variable names as per coreboot convention.
During renaming process, this patch also removes unused variables
listed below:
-> SataEnable // Checked in SoC code based on PCI dev enabled status
-> ITbtConnectTopologyTimeoutInMs // SoC always passes 0, so not used
Note: Since separating out changes into smaller CL might break the
compilation for the patch set, this is being pushed as a single big CL.
BUG=None
BRANCH=firmware-brya-14505.B
TEST=All boards using ADL SoC compiles with the CL.
Change-Id: Ieda567a89ec9287e3d988d489f3b3769dffcf9e0
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
It is necessary to build crossgcc.
Change-Id: I32f6507b4d8346bf94aaccd3eef4f22697c33965
Signed-off-by: Eloy Degen <degeneloy@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Commit hash b8b40964 ( mb, soc: Add the SPD_CACHE_ENABLE) introduced
per mainboard logic to invalidate the mrc_cache.
This patch moves mrc_cache invalidating logic into IA common code and
cleans up the code to remove unused argument `dimms_changed` from SoC
and mainboard directory.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6f18e18adc6572571871dd6da1698186e4e3d671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
This patch adds `FSPM_UPD *` as argument for
mem_populate_channel_data() and read_spd_dimm().
This change will help to update the architectural FSP-M UPDs in
read_spd_dimm().
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I770cfd05194c33e11f98f95c5b93157b0ead70c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
This patch modifies `memcfg_init` and `variant_memory_init`functions
argument from FSP_M_CONFIG to FSPM_UPD.
This change in `memcfg_init()` argument will help to update the
architectural FSP-M UPDs from common code blocks rather than going
into SoC and/or mainboard implementation.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=Able to build and boot redrix without any visible failure/errors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3002dd5c2f3703de41f38512976296f63e54d0c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
Hoglin and Herobrine (proto1) should share majority of GPIOs.
Conslidating the QUP initializations in mainboard. Also, putting
fingerprint init in a conditional as not all devices will have an FP
sensor.
BUG=b:182963902,b:223826899
BRANCH=None
TEST=booted BIOS on hoglin and check for i2c errors in dmesg
Change-Id: I48ce42760f2c75f04619b967a05909d2b3f28e2c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
New board introduced to trogdor family.
BUG=b:223101874
BRANCH=none
TEST=make
Signed-off-by: Mars Chen <chenxiangrui@huaqin.corp-partner.google.com>
Change-Id: Ie83df3c753d0863841430fe62805250ef8efeae9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I0a2b68a4b4b54c7345280b252d624799316641b1
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
SeaBIOS 1.16.0 was released on March 2nd. Thus, update the stable
version from 1.14.0 to 1.16.0.
Change-Id: I475a9be47171bfbe3b3c2d4d1d14bb753d8575a8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Currently the BayHub eMMC enable pin is using the default
configuration from the baseboard, which leads to RTD3 not being able
to control the GPIO when exiting and entering suspend. To fix this,
program the GPIO in the ramstage GPIO table.
BUG=b:222436260
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
scope enable pin while performing suspend stress and enable pin
works as expected.
test suspend stress 1000 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I1b6f164cc326bd368addb1e143ad2cbd449bb08d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Pull GPP_D16 to low when suspending, otherwise it will remain active
and use power.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I2cbe7caf66e8d8c27414aca3b74416c2b8115ea1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
DDR4 SPD data needs to be 512 byte to comply with the spec.
Though there is no vital timing data used beyond 256 byte there are some
part information which will be used to show the part info in the
coreboot log. If the buffer is too small this log shows garbage.
This patch increases the SPD buffer size from 256 byte to 512 to avoid
side effects.
Change-Id: I5b88df7818cfd62b3579d69f9f5bb14880f49c8c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie75912698e58088ff4a334403cb331542abb40fd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62754
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch uses generic enum type values for EOP command handler. So,
it renames cse_eop_result enum type to cse_cmd_result and also renames
the enum values to have generic name.
TEST=Build the code for Gimble
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ie0efa8fff08318ed863010db289959d113f4767e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The patch implements error handling as per the ME BWG guide. The BWG
recommends HECI interface reset if there is a timeout or malformed
response is received from the CSE. Also, the patch triggers HECI
interface reset if the CSE link state is not ready in the heci_send()
API.
TEST=Verify HECI Interface reset in the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3e4a97800cbc5d95b8fd259e6e34a32fc82d8563
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The patch implements below changes:
1. Implements different error codes and use them in appropriate
failure scenarios of below functions:
a. heci_send()
b. recv_one_message()
c. heci_receive()
2. As heci_send_receive() is updated to return appropriate error codes
in different error scenarios of sending and receiving the HECI
commands. As the function is updated to return 0 when success, and
non-zero values in the failure scenarios, so all caller function have
been updated.
BUG=b:220652101
TEST=Verified CSE RX and TX APIs return error codes appropriately in
the simulated error scenarios.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ibedee748ed6d81436c6b125f2eb2722be3f5f8f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
1. Update override devicetree based on schematics.
2. ALC5682I-VS is for audio codec.
BUG=b:218786363, b:214025396, b:212183045
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I08a1c2f784175b208ccdc562668041f432618dfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The verstage.c file contains PSP verstage specific code. We don't need
it when using x86 verstage.
BUG=b:193050286
TEST=Build and boot guybrush with x86 verstage
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6dc928cdce0c922bb18f4479b993c89dff106070
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62740
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This sets EPP value to be 45% for all Brya variants.
Historically, EPP Ratio has always been 50% (128) on Chrome platforms.
But on Intel Alderlake EPP ratio of 45% is recommended for optimal
power and performance on Chrome platforms.
BUG=b:219785001
BRANCH=firmware-brya-14505.B
TEST=
Use 'iotools rdmsr [cpu id] 0x774' command and check field 32:24 = 0x73.
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: I973cfec72a0be24c56c4cd3283d2fe6e18400d02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This updates energy performance preference value to all logical CPUs
when the corresponding chip config is true.
BUG=b:219785001
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: Ie59623fe715b0c545f8d4b6c22ab2ce670a29798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update PL1, PL2, and temperature sensor values from thermal team,
as well as, we remove unused temperature sensors according to
baseboard/devicetree.cb and mainboard schematic. After we check
DTT setting, the thermal and performance test pass.
BRANCH=dedede
BUG=b:204229229
TEST=on beadrix, run following commands:
localhost /tmp # cat /sys/class/thermal/thermal_zone*/type
x86_pkg_temp
INT3400 Thermal
TSR0
TSR1
TCPU
localhost /tmp # cat /sys/class/thermal/thermal_zone*/temp
45000
20000
32800
32800
39000
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Ibc59c4aa431f600158e744f5bbdc6d59a07a1ef3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62729
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The one USB2 port on the XHCI2 controller should have the port ID 2.0,
since it's the first USB2 port on that XHCI controller.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4a370132960939bccec4eb69a6590d0880b04137
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62713
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GFX HDA is the audio controller that provides audio output via the
external display connection, ACP is the audio coporcessor for the on-
board audio codec and XHCI2 is the third XHCI controller that provides
one USB 2.0 port. All those devices are used, so enable them in the
board's devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I186797a832470eb17752e06aa2fcc0b5c9db0398
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62571
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select GL9750 driver and add power sequence according to datasheet:
GL9750S-OIY04 rev1.22.
BUG=b:223304292
TEST=check GL9750 can get enumerated by kernel 5.15.
01:00.0 SD Host controller: Genesys Logic, Inc Device 9750 (rev 01)
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib6d461a56f6aeba30994daafe8993c36df4b309d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Enable pen garage. Pen detect is active low. And wake system when
eject.
BUG=b:223476974
TEST=evtest work as expected.
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 0
Properties:
Testing ... (interrupt to exit)
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: -------------- SYN_REPORT ------------
Event: type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I2f676301c3372a4760853ce9c10b75f94e22bbcd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This change mostly changes links that were identified as broken by
the 'website_scans' jenkins job.
There were some links that seem to be up at times, but that are
identified by link-checker as broken because of SSL issues.
At least one other link was changed to point to archive.org so
that it doesn't break at some point in the future. We should
probably try to make sure that everything is archived there and
point to those versions when possible.
There are still lots more links to do.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I36868ddf6113e18fa6841427dd635c75445b7bef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
There is no need that the tutorial for flashing firmware has its own
point in the main menu. Thus, move it to the tutorial section.
Change-Id: Ife6d97254af4c006fe01480a78c76303f9cb34bb
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
|
|
In preperation for CB:62424, replace HTTP links pointing to the flashing
firmware tutorial with file paths to the Markdown files.
Change-Id: I6a271a912348cbe002bc9cced9922ed743e1133c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: Ia0a1564f41d796ce86179d06b1d0b64021dc0a43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62660
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
instead
Only one ACPI device should be added to a PCIe root port. For the root
ports which already have device created, the generated code from this
driver needs to be merged with the existing device.
By default, this driver will create new device named DEV0.
This change allows to generate code under an existing device.
ex: (generate code under PXSX):
Scope (\_SB.PCI0.RP01.PXSX)
{
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package (0x01)
{
Package (0x02)
{
"UntrustedDevice",
One
}
}
})
}
BUG=b:221250331
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I80634bbfc2927f26f2a55a9c244eca517c437079
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Since the new loglevel markers were added, there will now be a marker
character at the beginning of the coreboot banner string, and this will
make the existing regular expressions meant to find it fail to match.
This patch fixes the problem by just allowing for a single extra
character there (any character to avoid the hassle of having to match
the marker explicitly). The extra character is optional so that we will
still continue to match banners from older versions of coreboot as well.
Since the `?` glyph is not available in basic POSIX regular expressions,
we have to switch to REG_EXTENDED syntax (should otherwise make no
difference). (Also, move side effects out of assert() while I'm here,
that's not actually safe for the standard libc implementation.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I99fb347eb1cf7b043a2113dfda7c798d6ee38975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62720
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get boot performance timestamps from CSE and inject them into CBMEM
timestamp table after normalizing to the zero-point value. Although
consumer CSE sku also supports this feature, it was validated on
CSE Lite sku only.
BUG=b:182575295
TEST=Able to see TS elapse prior to IA reset on Brya/Redrix
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 88,000
945:CSE started to handle ICC configuration 88,000 (0)
946:CSE sent 'Host BIOS Prep Done' to PMC 90,000 (2,000)
947:CSE received 'CPU Reset Done Ack sent' from PMC 282,000 (192,000)
0:1st timestamp 330,857 (48,857)
11:start of bootblock 341,811 (10,953)
12:end of bootblock 349,299 (7,487)
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Idcdbb69538ca2977cd97ce1ef9b211ff6510a3f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure PCIe Clk Source and Clk Request mapping. Configure GPIOs used
for WLAN. Mappping derived from Skyrim schematic.
BUG=b:214412172
TEST=Builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I16e35b443f741d366589fefb7fd21863369d1ec2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
GPIO 32 was not allocated correctly, updating to reflect the native
function use of the pin
BUG=b:214412172
TEST=Builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Idadd2a802b3244eba8ee83f80d8f10baebe4ca40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62717
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initialize trackpad on Qualcomm reference boards
BUG=b:182963902,b:223826899
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I93e866d92cf37887a98de88b4b2d768562515670
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62226
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to copy the PSP verstage logs into x86 cbmem, we need to enable
DEBUG_SMI. This will include the CBMEM console code in SMM. I only
enable DEBUG_SMI when UART is disabled because SMM doesn't currently
save/restore the UART registers. This will result in clearing the
interrupt enable bits and makes it so you can no longer use the TTY.
BUG=b:221231786, b:217968734
BRANCH=guybrush
TEST=Build serial and non serial firmware and verify DEBUG_SMI is set
correctly.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I85a7933e8eb49ff920d00e43a494aaeab555ef3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Now that SMM can write to CBMEM we can simply replay the transfer buffer
cbmem console to move it into the main cbmem console.
replay_transfer_buffer_cbmemc() relies on the EARLY_RAM linker symbols.
Since the SMM rmodule get linked with a different linker script than
bootblock/romstage it doesn't have access to these symbols. In order to
pass these symbols into SMM, we parse the bootblock.map file and
generate an early_ram.ld script. This script is then used when linking
SMM.
I replay the buffer in `smm_soc_early_init` because this call happens
before `console_init()`. `console_init()` prints the SMM header and we
want to append the verstage contents before printing the header to avoid
confusion.
BUG=b:221231786
TEST=Perform S0i3 cycles and verify PSP verstage logs now show up when
doing `cbmem -c`.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I64d33ccdee9863270cfbcaef5d7c614349bd895c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change provides hooks for the SoC so it can perform any
initialization and cleanup in the SMM handler.
For example, if we have a UART enabled firmware with DEBUG_SMI, the UART
controller could have been powered off by the OS. In this case we need
to power on the UART when entering SMM, and then power it off before we
exit. If the OS had the UART enabled when entering SMM, we should
snapshot the UART register state, and restore it on exit. Otherwise we
risk clearing some interrupt enable bits.
BUG=b:221231786, b:217968734
TEST=Build test guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I946619cd62a974a98c575a92943b43ea639fc329
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
