| Age | Commit message (Collapse) | Author |
|---|
|
This patch currently contains the following -
1. Use SOC_INTEL_COMMON_BLOCK_FAST_SPI kconfig for common FAST_SPI code.
2. Perform FAST_SPI programming by calling APIs from common FAST_SPI library.
3. Use common FAST_SPI header file.
Change-Id: I4fc90504d322db70ed4ea644b1593cc0605b5fe8
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/19055
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When using Wake On Voice &/or DCI, it requires xtal to be active during
low power idle.
With xtal being active in S0ix state power impact is 1-2 mW.
Hence set xtal bypass bit in CIR31C for low power idle entry.
TEST= Build with s0ix enable for Poppy. Boot to OS & verify that
bit 22 of CIR31C register is set. s0ix works.
Change-Id: Ide2d01536f652cd1b0ac32eede89ec410c5101cf
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19442
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a configuration option to assign the binaryPI base address
for the ACPI registers. The binaryPI's assignment is determine
at build time and no run-time configuration is allowed.
Change-Id: Ida17022abfa6faceb0653c2cb87aacce4facef09
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19485
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Claim memory-mapped regions in the legacy area.
Claim an MMIO resource for the A000 and B000 segments, and reserved
resource for C000 through F000 segments.
These changes allow code and information to be retained in the event
unused regions get wiped.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit d612d4fe69881609d42053496409c452e1014947)
Change-Id: I9c47c919bbfd0edccf752e052f32d1e47c1a1324
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19156
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
cbgfx currently does not support portrait screen which height >width.
so add it.
Change-Id: I66fee6d73654e736a2db4a3d191f030c52a23e0d
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19474
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Define a common area in CAR so that the storage data structures can be
shared between stages.
TEST=Build and run on Reef
Change-Id: I20a01b850a31df9887a428bf07ca476c8410d33e
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19300
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Create Intel Common FAST_SPI Controller code.
This code contains the code for SPI initialization which has
the following programming -
* Get BIOS Rom Region Size
* Enable SPIBAR
* Disable the BIOS write protect so write commands are allowed
* Enable SPI Prefetching and Caching.
* SPI Controller register offsets in the common header fast_spi.h
* Implement FAST_SPI read, write, erase APIs.
Change-Id: I046e3b30c8efb172851dd17f49565c9ec4cb38cb
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18557
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set up IGD OpRegion in northbridge and fill in GNVS' aslb.
At this point GNVS already has been set up by SSDT injection.
Required for future VBT patches that will:
* Use ACPI memory instead of CBMEM
* Use common implementation to locate VBT
* Fill in platform specific values
Change-Id: I97c3402ac055991350732e55b0dda042b426c080
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19310
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set up IGD OpRegion in northbridge and fill in GNVS' aslb.
At this point GNVS already has been set up by SSDT injection.
Required for future VBT patches that will:
* Use ACPI memory instead of CBMEM
* Use common implementation to locate VBT
* Fill in platform specific values
Change-Id: I76b31fe5fd19b50b82f57748558fb04408e0fd23
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19309
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set up IGD OpRegion in northbridge and fill in GNVS' aslb.
At this point GNVS already has been set up by SSDT injection.
Required for future VBT patches that will:
* Use ACPI memory instead of CBMEM
* Use common implementation to locate VBT
* Fill in platform specific values
Change-Id: Ie5d93117ee8bd8d15085aedbfa7358dfcf5f0045
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19307
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The AFC—Additional Flash Control Register is set by
southbridge code.
Remove redundant calls and get rid of it in autoport.
Change-Id: I627082e09dd055e3b3c4dd8e0b90965a9fcb4342
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19493
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Based on Thinkpad x230 and schematics.
Verified by autoport.
USB debug port is the left front usb port
Thanks to Holger Levsen for the device.
Change-Id: I97c8e01a3ce0577d7dc9e8df7d33db3b155fe3d6
Tested-on: lenovo x1 carbon gen 1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16994
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Haswell, Broadwell, Baytrail, and Braswell ChromeOS devices'
FADT version were incorrectly set to 3, rather than the correct
ACPI_FADT_REV_ACPI_3_0. The incorrect value resulted in these
devices reporting compliance to ACPI 2.0, rather than ACPI 3.0.
This mirrors similar recent changes to SKL and APL SoCs.
Test: boot any affected device and check ACPI version reported
vai FADT header using OS-appropriate tools.
Change-Id: I689d2f848f4b8e5750742ea07f31162ee36ff64d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19498
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Write vendor/device id to subsystem vendor/device id
if they are not provided.
Change-Id: I5027331a6adf9109767415ba22dfcb17b35ef54b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/19467
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Change-Id: Icba9d7910dfd46f32a2c46b6fd064a9cc8e3beac
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/19242
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Enable audio:
* Add verb table for ALC286 & ALC298
* Enable virtual channel 1 for DmiVc1 & HdaVc1.
TEST= Build for kblrvp3 as well as kblrvp7. Boot to OS & verified
working of audio on both the boards.
Change-Id: Id27e3cf585b93ed4131d7bf3d3b53d3f5404b18e
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18875
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Bug=b:35775024
BRANCH=None
TEST=boot up successfully to kernel on Fizz i7 sku
Change-Id: Iccf9fbef1333f3fea78091b679c2676411559987
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19486
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable/Disable the PCIe ports to match factory BIOS. The port #6
is used for PCIe on the M.2 connector which allows for NVMe SSDs
to function.
Change-Id: I8058cbad3da651144545d588c0ae78c5f5e598ac
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19446
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The Wildcat Point-LP Premium is handled the same as the Wildcat Point-LP,
but it wasn't supported by inteltool.
Change-Id: I694514e1963f074582a3f5f81d63c20e7fa49189
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19445
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Lint prevents my next commit which adds a new line to the table
so it's better to break all the > 80 character lines so it will be
consistent with the new line I'm about to add.
Change-Id: Ic7ad0cb90e861cd830db1186225d4f839250792a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19444
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
input_underrun is defined but not used. A reasonably new compiler,
enabled warnings and warnings-as-error make the build break for no good
reason.
Change-Id: Ibeb7ba53aad5738938093ab7b34695c9c99c9afe
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/19482
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
It's standard practice in vboot that the FWID consists of
<board_name>.<version_number> (e.g. Google_Kevin.8785.57.0). In fact,
some tools rely on this and cut the string at the first dot to
separate the two.
The current Kconfig default in coreboot instead leads to ugly,
parser-breaking FWIDs like Google_Kevin4.5-1234-5678abcd. This patch
fixes that.
Change-Id: I65cd5285c69e2e485d55a41a65d735f6a2291c16
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19487
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Correct the default GBB_HWID to "ROWAN TEST 9387"
BRANCH=chromeos-2016.05
BUG=b:35774871
TEST=emerge-rowan coreboot chromeos-bootimage,
strings /build/rowan/firmware/image.bin | grep "ROWAN TEST"
and look for 9387 in output
Change-Id: I7851010305caf056958c8a6a328b0506bf2208cd
Signed-off-by: Patrick Berny <pberny@chromium.org>
Reviewed-on: https://review.coreboot.org/19488
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=b:37712455
Change-Id: I3209aaef774712edab5e9f656ee84bfb6917b1c1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19472
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
BUG=b:37712790
Change-Id: I7764b4ec55b0beea82eeb6c379ef38ceeb1fb04e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19471
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable separate MRC cache for recovery mode. This requires change in
flash layout to accomodate another region for RECOVERY_MRC_CACHE.
BUG=b:37682566
TEST=Verified following scenarios:
1. Boot into recovery does not destroy normal mode MRC cache.
2. Once recovery MRC cache is populated, all future boots in recovery
mode re-use data from the cache.
3. Forcing recovery mode to retrain memory causes normal mode to retrain
memory as well.
Change-Id: I4c748a316436001c5a33754084ab4a74243e21df
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19457
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
TEST=Build and run on Reef
Change-Id: I2f04a01e5e266422e3ef0d90541dc9d39471260c
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19301
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I1ef1323dc1f3005ed194ad82b75c87ef41864217
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19367
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3a55c2e8077fdb10768df287f38efcd5e2e64bdf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19365
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This needs some extra headers in amdk8/raminit.c that were otherwise
provided by that file.
Change-Id: I80450e5eb32eb502b3d777c56790db90491fc995
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19360
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
1. Select CONFIG_{TPM,TPM2} only when MOCK_SECDATA is not selected.
2. Provide tlcl_lib_init for mock TPM case.
BUG=b:37682566
TEST=Verified that when mock TPM is used, CONFIG_TPM is not set
anymore in coreboot config.
Change-Id: If3bdd1528e153b164e9d62ee9cbcc4c3666b8b66
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19456
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch uses common ITSS library to setup
itss irq.
Change-Id: Ibe65a92f1604277bec229c67f4375b6636c0972d
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/19244
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch uses common ITSS library to setup
itss irq.
Change-Id: Id265505cfc106668aea25ad93e114fe20736b700
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/19236
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create Intel Common ITSS code. This code currently only contains
the code for Interrupt initialization required in Bootblock phase.
More code will get added up in the subsequent phases.
Change-Id: I133294188eb5d1312caeafcb621fb650a7fab371
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/19125
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The SRS bit which is supposed to indicate reset button press
is non-functional. If it did work the system reset event it
was associated with is overly specific. Therefore, use the
warm reset status bit.
BUG=b:37687843
Change-Id: I34dd09c03d2bca72da9a5cdf23121e0d0e621fa6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19484
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
It's come to attention that apollolake doesn't support a full retrain
on warm reset. Therefore force a cold reset when a full retrain is
requested in the non-S5 path.
BUG=b:37687843
Change-Id: If9a3de1fa8760e7bb2f06eef93a0deb9dbd3f047
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19483
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update default ODT config to have correct CA ODT settings as the
current defaults are incorrect for all the current apollolake designs.
All the current designs pull both A and B channels' LPDDR4 modules' ODT
pins to 1.1V. Therefore, the correct impedance setting needs to be
applied.
In order for the settings to take effect one needs to clear the
memory training cache in deployed systems. Trigger this by bumping
the memory setting version for the SoC.
If needed in the future support for allowing the override of this
setting from the mainboard should be straight forward. It's just not
necessary at this time.
BUG=b:37687843
TEST=BAT test, warm, reboot, S3 cycle test
Change-Id: I9a2f7636b46492a9d08472a0752cdf1f86a72e15
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19397
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
On Chrome OS systems a memory setting change is needed to be deployed
without updating the FSP blob proper. Under such conditions one needs
to trigger retrain of the memory. For ease of use provide an option,
FSP_PLATFORM_MEMORY_SETTINGS_VERSIONS, which incorproates the SoC
and mainboard memory setting version number into the FSP version
passed to the platform. The lower 8 bits of the FSP version are the
build number which in practice is normally 0. Use those 8 bits to
include the SoC and mainboard memory settings version. When FSP,
SoC, or mainboard memory setting number is bumped a retrain will be
triggered.
BUG=b:37687843
Change-Id: I6a269dcf654be7a409045cedeea3f82eb641f1d6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19452
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
BUG=b:35647967
TEST=boot from bob
Change-Id: I756513f02ac13e159d5b8b1ac2346fa42cf3c219
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf18ed7b8fdf11594f812e5c48a2bd0fde5cb820
Original-Change-Id: I50c053ab7a6f6c14daee4fb2ab1cdcaeee2d67da
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/452286
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19434
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=b:35647967
TEST=boot from bob
Change-Id: I5de902ab26fe768b641f69d85a5294baf6d916e3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 223257d486b026c06a1f3a7a830b829efb9932dc
Original-Change-Id: I055ad5f59285cee3110d1e7cb1a53a60144712e4
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/452285
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19433
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
SD card detect pins should normally have a pull-up. It seems that for
micro-SD cards this doesn't really matter all that much, but for the
full-size slots we have on some Oak-derivatives (like Hana) it does.
BRANCH=oak
BUG=b:35854317
TEST=Booted Hana, confirmed that card detect no longer seemed stuck-on.
Booted Elm and confirmed that SD card behavior didn't change.
Change-Id: I9b20e0f6fe310e724d191e36ca0a81ab4fe5f593
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c2781eeef50f52c6f02ee9344274ddf4dcb0a946
Original-Change-Id: I428ac92efb07f94265673b04e0e0dd452649b9fd
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/452861
Original-Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/19432
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Ironically enough, libsanitizer is notorious for creating "uninitialized
variable" warnings with different compiler versions than the one it's
shipping with.
Since we don't need it for building the real compiler, just skip it.
Fixes building our compilers using the gnat-gpl 2014 compilers.
Change-Id: I2130dfdf3eaf07d77cd70777419fc0ae4642b843
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/19478
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Add basic SMM support for Broadwell-DE SoC.
The code is mainly based on the SMM implementation of Broadwell with a
few differences:
- EMRR is now called PRMRR and the UNCORE part of it is not available
- SMM_FEATURE_CONTROL is no longer a MSR but is now located in PCI space
- currently only SERIRQ-SMI has a handler
Change-Id: I461a14d411aedefdb0cb54ae43b91103a80a4f6a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19145
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
On Apollo Lake it was discovered that our current FADT implementation is
valid for ACPI version 3.0 but misses fields for ACPI version 5.0. We
run into booting issues with Windows 10 using version 5 in the FADT
header. In commit 2b8552f49bc3a7d0290f96a84b573669de396011
(intel/apollolake: Switch FADT to ACPI version 3.0) we go back to
version 3 for Apollo Lake. Skylake is now the last platform that uses
version 5 in FADT header.
Change-Id: I2d0367fae5321dee4ccac417b7f99466f8973577
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19453
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The current implementation of the FADT structure is only ACPI 3.0 compliant.
Setting the version to ACPI 5.0 results in a corrupt FADT. Linux seems
to be able to deal with it but Windows 10 hangs in a really early stage
without any notification to the user.
If ACPI 5.0 is mandatory, the FADT structure needs to be adjusted to
match the specification. Therefore the members sleep_ctl and sleep_stat
needs to be added to FADT structure.
Change-Id: I51c7a7a84d10283f5c2a8a2c57257d53bbdee7ed
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19146
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
kconfig uses mktemp so ..config.tmp isn't enough.
Change-Id: If910a40269783bbf7392b44cda7e9750bc33f14d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/19459
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Move the images around in the image stitching. This addresses
an issue found with PSP firmware loading on the Google Kahlee
mainboard.
Note firmware1 must come before firmware2 in the image or
the PSP will not allow APU to execute.
Change-Id: I85963fa93d6efd707cedfbc04b92d302ad5de3b1
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19170
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The new touchpad firmware uses i2c-hid instead of custom reporting
protocol. The touchpad also exposed another slave address (0x1e) for
kernel to communicate with the touchpad EC.
Change-Id: Iecaf14f7b8aed836120569e9ade9c3115bc00264
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/19461
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add a check for vboot when locating the binaryPI image.
There is currently an ordering problem using cbmem to locate the
image when vboot is present. Vboot inserts its locator into the
search process so that memory can be checked before flash is queried.
For the earliest calls using the wrapper, DRAM has not been set up
and cbmem not initialized in romstage. This change prevents an
endless loop when vboot searches cbmem.
This change has another side effect. When vboot is in effect, the
change forces the RO binaryPI to be used even when on either of the
RW paths. There is currently no ability to relocate the XIP image
for use in a RW region.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 6efe9217c38cf93fd9b38e52cf3ec90fee3d0474)
Change-Id: I0c14bd729f8a67bca37cbdbd3a5e266c99c86d54
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18438
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
AMD VBIOS option ROMs often modify themselves during initialization.
Check for the presence of a VBIOS at 0xc0000 before populating the
VFCT table. If a matching ROM is found, use it for the source of
the copy.
Tested on Gardenia (Stoney) variant by observing amdgpu driver's
dmesg output.
Change-Id: I5be7e1562bde51800c5b0e704c79812d85bcf362
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19383
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We need to rewrite libtool's files (foo.la) a couple of times so it
knows where to look
(while still whining that $DESTDIR$TARGET != $TARGET. well, duh.)
Change-Id: I54cafd47c76d855222ba905b5eb4533a23bdfd34
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/19463
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In order for PD charge events to properly notify the OS when a charger is
attached we need to enable the PD MCU device and event source from the EC.
Without this change the charging still happens, but the OS does not notice
and update the charge state icon in the Chrome OS UI.
BUG=b:35586577
BRANCH=none
TEST=On a poppy board that has the VBUS rework applied, plug in a charger to
either port and see charge status updated to indicate charging in the
power_supply_info tool and the Chrome OS UI.
Change-Id: I59dcfc1cb5d11841f56cac7f4ffe461c2f9ec52a
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/19441
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
If the mainboard supports VBNV, call init_vbnv_cmos() instead of
the normal init_cmos(). The VBNV version does some VBNV pre
and post setup around the normal init_cmos().
Change-Id: I34b02409019b945cd68c830e006e99338643f29c
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19399
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Once the PCI command register is written the bridge forwards
future IO and memory regions, as programmed in the respective base
and limit registers, to the secondary PCI bus.
Since the LPC function claims the resources for IOAPIC, ROM and
low IO (0x0-0xfff) in its read_resources() call, the PCI-to-PCI
configuration will not overlap those regions and does not hide
the resources mentioned in the original comment.
The bridge was disable in the following commit [1]
commit a8e1168064b34b46494b58480411a11bc98340f6
Author: Stefan Reinauer <stepan@coresystems.de>
Date: Wed Mar 11 14:54:18 2009 +0000
This patch contains some significant updates to the i82801gx component and will
be required for a series of later patches. Roughly it contains:
but unfortunately it was not noted which system this caused
problems with.
[1] http://review.coreboot.org/gitweb?p=coreboot.git;a=commit;h=a8e1168064b34b46494b58480411a11bc98340f6
Change-Id: I75128d83a344f4a0e09a3ea623c7f92a016ebfb9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/2706
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
For this debug.c needs to be linked too.
Change-Id: I9cd1ffff2c39021693fe1d5d3f90ec5f70891f57
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19030
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
BUG=b:37684299, b:35775024
BRANCH=None
TEST=reboot and ensure graphics are displayed through
HDMI port.
Change-Id: I74a664b2d42f55adfa64f292f6ede4c956e16fbf
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19451
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:37486021
BRANCH=None
TEST=compile coreboot and make sure sda and sdb show
up in /sys/class/block.
Change-Id: I11344a4a5fc7e5b5d907d25439f92744a5fb70da
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19450
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit e7394ca90366d35ac52416c21052a3ceb459dc81.
Configuration register for ACPI PM base address is initially configured
inside the PI blob. Therefore, the value of HUDSON_ACPI_IO_BASE needs
to be the same as DFLT_ACPI_PM1_EVT_BLOCK_ADDRESS used in the build
of binaryPI blob.
Change-Id: I36700e49e21cc675e8e22b06efffb40e9c1e4236
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19454
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I324edce44ad82217ac1fba177f4a0bb3c799308c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19426
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Replace ram_check with quick_ram_check, because ram_check is slow and
is destructive for dram content.
Change-Id: I5fb1bfe711549aabb6e597bda22848988a7e9cbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19416
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is not needed.
Change-Id: Id19a00c1546b7a71d90aa8c7e43e6efde1e9fbbc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19425
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
MMA blobs are SOC specific (not board). So far MMA
is supported by big cores (SKL and KBL).
Change-Id: I922789a2a12d55360624dd6de15ab9f0bb5f0acf
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/19260
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a function to send the TPM decode to the SPI interface.
Enables use of SPI TPMs on Hudson mainboards.
Change-Id: I0e85ed92163e38eca6a55456708ab322d6a90d4c
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19402
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change spaces to tabs and do general whitespace cleanup.
Change-Id: I4a4ecd42f91c9c6015a4f065b7386b17523ac6d9
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19401
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Move the ACPI IO registers from 0x800 to 0x600 to avoid the
IO space required by the Google EC, also at 0x800.
This shouldn't have any conflicts on other AMD systems.
Change-Id: Iac7388c15e899277fd506fb37965164488358335
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19171
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a function to enable LPC IO decode AKA WideIO.
This can enable up to 3 regions, which may be 512 or 16
bytes wide.
Change-Id: I2bed3a99180188101e00b4431d634227e488cbda
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19160
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It turns out that there are quite a few other projects that can access
the CBMEM console by now. If we ever want to make another structural or
behavioral change to it, we need to know where these implementations are
so we can make sure they're all getting updated. Let's try to build a
comprehensive list in the file that should be the source of truth for
all (coreboot's own implementation).
Change-Id: Ia3d6a87230f5bfdde9d812bc7154e22880c1377a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19439
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a basic GPIO get function.
Note that GPIO set, ACPI/GPE, and other features should come
in future commits. Future changes to be modeled on the other soc/
gpio functions.
Change-Id: I8f681865715ab947b525320a6f9fc63af1334b59
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19159
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The silicon specific mainboard_romstage_entry() in amd/cpu/car.h,
which is used by all AMD silicon car code, caused a conflict.
Move the silicon specific defines to silicon header files. Also,
no longer include car.h in the romstage file.
Change-Id: Icfc759c4c93c8dfff76f5ef9a1a985dd704cfe94
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18769
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
These files are actually indentical, but unfortunately, the formatting
was changed without caring for the already present files. Fix that. Use
the license formatting where less lines are used.
The next step is to put that in a common location.
Change-Id: Iecb263b9d321a33e64988b315220893df2e0045c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19423
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
According to the comment above the default should dump the EC ram,
though is never reached since the variable 'write_addr' is not 0, but
initialized at -1.
Also removes brackets around one line statement below if to make
checkpatch.pl happy.
Change-Id: I390996b253f2f20682cd9ab2d4f560de6eccfc57
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19152
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
When setting output to verbose, it incorrectly reports that it times
out on every command.
TESTED on Thinkpad X60.
Change-Id: I24f05f0c165462d5ba2604c7e2fe139400683275
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19151
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Update the PCI ID for SATA controller on Kaby Lake.
Change-Id: Id0b5e0366e04fbac6a57a15407f33f390a2a1856
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19395
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Utilize the postcar stage for tearing down CAR and initializing
the MTRRs once ram is up. This flow is consistent with apollolake
and allows CAR_GLOBAL variables to be directly accessed and no
need for migrating CAR_GLOBAL variables as romstage doesn't
run with and without CAR being available.
Change-Id: I76de447710ae1d405886eb9420dc4064aa26eccc
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19335
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ib6f8ee937c4f3d8e2c0ff3851a819077fa499ccc
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19334
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The devicetree data structures have been available in more than just
ramstage and romstage. In order to provide clearer and consistent
semantics two new macros are provided:
1. DEVTREE_EARLY which is true when !ENV_RAMSTAGE
2. DEVTREE_CONST as a replacment for ROMSTAGE_CONST
The ROMSTAGE_CONST attribute is used in the source code to mark
the devicetree data structures as const in early stages even though
it's not just romstage. Therefore, rename the attribute to
DEVTREE_CONST as that's the actual usage. The only place where the
usage was not devicetree related is console_loglevel, but the same
name was used for consistency. Any stage that is not ramstage has
the const C attribute applied when DEVTREE_CONST is used.
Change-Id: Ibd51c2628dc8f68e0896974f7e4e7c8588d333ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19333
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The console log level variable doesn't really rely on ROMSTAGE_CONST
proper. Instead, the mutability of the variable is based on the current
implementation of ROMSTAGE_CONST (__PRE_RAM__). As such directly
use that logic for the code. In addition, refactor the code to let
the compiler and linker optimize out accesses instead of using
the pre-processor.
Change-Id: I44bcc409266ef52b9be29f75efde73a6707a53f4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19438
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The ramstage-c-ccopts variable needs to be double dereferenced
for the cbfs-files-processor-struct handler so all the ccopts
are included since the ramstage-c-ccopts is fully constructed
later by another function. Without this not all the flags
are present on the command line.
Change-Id: I5425b3c1f23d767c61f654dd287584403f85d719
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19380
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
In the safety considerations, we should make sure the slot of SD is
enabled first, since we want to the power switch of corresponding is
powered up.
The different boards have the different power switch for sdmmc.
Some power switch IC need turn on delay for long time.
let's move the slot power of SD to romstage and avoid explicit delays
or per-board.
BRANCH=none
BUG=b:35813418, b:35573103
TEST=check the signal for children of gru, and boot up from sd card.
Change-Id: Id164e4c4c900c6b1ca0251fc27db4cd36c56f6ff
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ea1b01cc13628033b85251dbb44407f075efdc85
Original-Change-Id: I48ab543143d3de9be46608fc12d78e09decf8d79
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/447076
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19430
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Delete the write to PM register 0xee. This register is not
listed in the current BKDG and S4 is not currently supported
on this APU.
NDA document #47517 "A55/.../A85X fusion Controller Hub Register
Reference Guide" provides some clues on the intent of this write.
This register has always been observed to power on with a value
of 0x08 so the write has no effect.
This should be revisited again when SMI and PSP fully implement
the support required for S3.
Change-Id: I35e6c5f7ad1de7f51b018543d2f7ce82182f11e4
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18494
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create new functions similar to read and write of other sizes.
Change-Id: I35a08c498f25227233604c65c45b73b1c44fae1f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19394
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Unlike other oak derivatives, Rowan uses an 8-lane BOE tv097qxm-nu0
MIPI/DSI panel that requires dual DSI support.
Rework oak display initialization to special case Rowan, which uses a
provided edid struct for its panel, special panel backlight sequencing
and needs to configure mtk_ddp and mtk_dsi to use dual dsi mode.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: I136ba5bd1ab12c4ad92995e066fc6d6cf54d0898
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19389
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The MT817x display output pipeline can be configured to drive an 8-lane
MIPI/DSI panel using "dual DSI" mode. For the "dual DSI" video data path,
the UFO block is configured to reorder the data stream into left and right
halves which are then sent by the SPLIT1 block to the DSI0 and DSI1
respectively. The DSI0 and DSI1 outputs are then synchronously clocked at
half the nominal data rate by their respective MIPI_TX0/MIPI_TX1 phys.
Also, update the call sites in oak mainboard to avoid build breakage.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Id47dfd7d9e98689b54398fc8d9142336b41dc29f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19361
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This helper function was introduced so that mainboards don't need
to manually fill in these struct edid fields.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Ic9404a786a28b314b710e037dcae776be4b584ca
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19388
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The SD/MMC support is broken into several pieces. There are three main
data structures:
* sdhci_ctrlr - This is SDHCI controller specific and defined in
include/device/sdhci.h
* sd_mmc_ctrlr - This contains generic controller management data and
defined in include/device/sd_mmc_ctrlr.h
* storage_media - This contains the flash storage device management data
and is defined in include/device/storage.h
The SD/MMC driver consists of several components:
* SDHCI controller code
* bouncebuf.c
* bouncebuf.h
* pci_sdhci.c
* sdhci.c
* sdhci.h
* sdhci_adma.c
* sdhci_display.c
* Flash storage device support
* mmc.c
* mmc.h
* sd.c
* sd_mmc.c
* sd_mmc.h
* storage.c
* storage.h
* storage_erase.c
* storage_write.c
Kconfig values enable various portions of the controller and storage
drivers to be built to reduce the overall size of what is included in
the final image.
Full read/write/erase operations are provided for those platforms which
want to take advantage. It is also possible to build the driver to
perform initialization only. By default, this driver is not included in
any platform, platforms must specifically select DRIVERS_STORAGE to add
the SD/MMC support.
After this patch is reviewed and merged, there are some additional
patches:
* Common CAR storage area - Use a predefined region of CAR to pass data
structures between bootblock through to romstage. This allows early
stages to preform the SD/MMC device initialization and later stages
to use the SD/MMC device without further initialization. The example
code initializes the SD/MMC device in bootblock and uses the SD/MMC
device in romstage without further initialization.
* CBMEM ID - Add a CBMEM ID value for the data structures so that they
may be passed from romstage to ramstage and eventually the payload.
The example uses the SD/MMC device in ramstage without further
initialization.
* Move the SD/MMC driver into commonlib
* Have libpayload build the SD/MMC driver from commonlib. The intent
is to pass the controller state to libpayload so that the SD/MMC
device can be used without further initialization.
* On some platforms, have depthcharge use the commonlib SD/MMC driver
History:
Copy the SD/MMC driver from depthcharge revision eb583fa8 into coreboot
and make the following changes:
* Removed #include "config.h" from mmc.c, allow the lint tests to pass.
* Move include files from drivers/storage into include/device.
* Rename mmc.h to storage.h.
* Add the Kconfig and Makefile and make edits to get the code to build.
* Add support to initialize a PCI controller.
* Fix formatting issues detected by checkpatch.
* Fix data flow issues detected by checkpatch.
* Add the missing voltage (MMC_VDD_35_36) into the voltage mask.
* Rename the macros mmc_debug, mmc_trace and mmc_error to sd_mmc_*.
* Replace printf with sd_mmc_error.
* Add sdhc_debug, sdhc_trace and sd_error macros.
* Add Kconfig values to enable storage device debugging and tracing.
* Add tracing and debug support to the SDHCI driver.
* Allow SOC to override more controller features.
* Split out ADMA support.
* Move 1V8 support into SOC routine.
* Move HS400 support into SOC routine.
* Rework clock handling.
* Change all controller references to use ctrlr.
* Update the voltage handling.
* Update modes of operation.
* Move DMA fields into MmcCtrlr.
* Update bus width support.
* Change MMC_TIMING_* to BUS_TIMING_*.
* Rename MMC_MODE_ to DRVR_CAP.
* Move quirks into ctrlr->caps.
* Associate removeable with the controller.
* Statically allocate MmcMedia.
* Replace the SdhciHost structure with the MmcCtrlr structure.
* Split the code to support other SD/MMC controllers.
* Split out erase and write support.
* Update the code to be more consistent with the coreboot coding style.
* Only expose calling APIs.
* Divide up mmc.c into 4 modules: MMC, SD, storage card, common code.
* Update debug and error messages.
* Add partition support.
* Display clock frequencies once in MHz.
* Remove mmc_send_cmd, use ctrlr->send_cmd instead.
* Handle error from sd_send_op_cond.
* Allow mainboard to control delays around CMD 0.
* Support command logging.
* Mainboard may set delay after SD/MMC command.
* Display serial number with sd_mmc_trace.
* Remove cmd set parameter from mmc_switch.
* Display errors for timeout and comm errors.
* Add LED support.
* Move 64bit DMA flag into ctrlr->caps.
* Rework PIO transfer routine.
* Add HS200 bus tuning.
* Add support for HS400.
* Use same format for HS400, HS200 and HS52.
* Reduce storage_media structure size
* Add routine to update code pointers
* Add display of storage setup
* Display controller setup
TEST=Build and run on Reef and Galileo Gen2
Change-Id: I9b5f9db1e27833e4ce4a97ad4f5ef3a46f64f2a2
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19208
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a Kconfig value to indicate coreboot builds.
Add prototypes and definitions for:
* dma_coherent
* dma_malloc
* xmalloc
* xzmalloc
Move prototype for memset into stdlib.h from string.h to eliminate build
breaks.
TEST=Build and test on Galileo Gen2
Change-Id: Ib2eb2ca143b0538bdd1863e628af4c1948bc0f8c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19207
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch enables TPM2 using cr50 over I2C for the Rowan board, and
adds an mt8173 specific TPM IRQ polling function. The function relies on
the appropriate EINT input configured to trigger the ready status on
the rising edge.
The cr50 TPM is on I2C address 0x50.
The cr50 interrupt GPIO is also made available for use by depthcharge
via the coreboot tables.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: If6cdd0e39e4ac86538f27f322c55c329179ee084
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19364
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add basic support to configure GPIOs to poll for external interrupts
(EINT).
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: I9d52591661a5a74ec1fd9a081f606f0a08a3a6ab
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19362
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The vendor.irq field was originally intended for use as the TPM 1.2
"command complete" interrupt. However, all actual coreboot tpm drivers
and hardware use the vendor.status method of checking command completion
instead, and this irq field is not used.
Let's just remove this unused functionality to simplify the code.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I994c5bfbd18124af9cb81d9684117af766ab0124
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19396
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: If66a2a1d461a411e112589c84a434066d48b9399
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19410
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ia1eacd15e71a46a37457ee2f117b156393c3393d
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19409
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The Cr50 TPM uses an IRQ to provide a "status" signal used for hand-shaking
the reception of commands. Real IRQs are not supported in firmware,
however firmware can still poll interrupt status registers for the same
effect.
Commit 94cc485338a3 ("drivers/i2c/tpm/cr50: Support interrupts for status")
added support for the Cr50 driver on X86 platforms to use a KConfig file
to supply an IRQ which it would poll using acpi_get_gpe. If the IRQ is
not supplied, the Cr50 driver inserts a 20 ms wait.
Unfortunately this doesn't work so well when using the i2c connected Cr50
on ARM platforms. Luckily, a more generic implementation to allow a
mainboard to supply a Cr50 IRQ status polling function was solved for SPI
connected Cr50s by commit 19e3d335bddb ("drivers/spi/tpm: using tpm irq to
sync tpm transaction").
Let's refactor the i2c c50 driver to use this same approach, and change
eve and reef boards to make use of DRIVER_TPM_TIS_ACPI_INTERRUPT for
specifying the TPM flow control interrupt.
This essentially reverts these two commits:
48f708d199 drivers/i2c/tpm/cr50: Initialize IRQ status handler before probe
94cc485338 drivers/i2c/tpm/cr50: Support interrupts for status
And ports this commit to i2c/tpm/cr50:
19e3d335bd drivers/spi/tpm: using tpm irq to sync tpm transaction
As a side effect the tpm_vendor_specific IRQ field goes back to its
original usage as the "TPM 1.2 command complete" interrupt, instead of
being repurposed to hold the flow control IRQ.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I004329eae1d8aabda51c46b8504bf210484782b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19363
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ic69add8a3ce35be64fb37db4ed40163f6144fc9c
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19408
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ifeb09a0a35bff7cd9091f6d027f0065288ca35c9
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19407
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Utilize the intel/common code for tis_plat_irq_status() to remove
dependencies and code duplication on for bringing up a board
requiring tis_plat_irq_status().
Change-Id: I2aaa1d7d3ce171dc1788438ff9990fce533deb6c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19371
Tested-by: build bot (Jenkins)
|
|
On Intel platforms utilizing the CR50 TPM the interrupts are routed
to GPIOs connected to the GPE blocks. Therefore, provide a common
implementation for tis_plat_irq_status() to reduce code duplication.
This code could be further extended to not be added based on
MAINBOARD_HAS_TPM_CR50, but that's all that's using it for now.
Change-Id: I955df0a536408b2ccd07146893337c53799e243f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19369
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The CR50 TPM can do both SPI and I2C communication. However,
there's situations where policy needs to be applied for CR50
generically regardless of the I/O transport. Therefore add
MAINBOARD_HAS_TPM_CR50 to encompass that. Additionally,
once the mainboard has selected CR50 TPM automatically select
MAINBOARD_HAS_TPM2 since CR50 TPM is TPM 2.0.
Change-Id: I878f9b9dc99cfb0252d6fef7fc020fa3d391fcec
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19370
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
MAINBOARD_HAS_SPI_TPM_CR50 describes a capability of the board and SPI_TPM
is only on if we actually want to compile in the TPM code. For example,
in src/drivers/i2c/tpm/Kconfig MAINBOARD_HAS_I2C_TPM_CR50 also doesn't
depend on SPI_TPM.
This problem manifests itself as the following build issue when building
with MAINBOARD_HAS_I2C_TPM_CR50 but without an explict "select TPM2":
src/Kconfig:296:error: recursive dependency detected!
src/Kconfig:296: symbol MAINBOARD_HAS_TPM2 is selected by MAINBOARD_HAS_TPM_CR50
src/Kconfig:408: symbol MAINBOARD_HAS_TPM_CR50 depends on MAINBOARD_HAS_SPI_TPM_CR50
src/drivers/spi/tpm/Kconfig:15: symbol MAINBOARD_HAS_SPI_TPM_CR50 depends on SPI_TPM
src/drivers/spi/tpm/Kconfig:1: symbol SPI_TPM depends on TPM2
src/Kconfig:396: symbol TPM2 is selected by MAINBOARD_HAS_TPM2
MAINBOARD_HAS_SPI_TPM_CR50 shouldn't depend on SPI_TPM.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: I0cb3f6d3aa4159bad563a6a4b006d7f4825e04b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Suggested-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19411
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Id1b7b98b4fba745ac0d55638b6a5cceba3c329ef
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19415
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
TESTED on D510MO.
Change-Id: I05aa40df0d2a090fcf734416669e9e1bbff094e4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19414
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
