| Age | Commit message (Collapse) | Author |
|---|
|
Configure RST and PWR_EN signals for both WFC and UFC
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: Ie416da373756b1c73472b8572f87930965a3d6ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47496
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C related GPIO as per ADL-P schematics.
This is based on Revision 0.974 of schematics.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I76e1207cb31bed10b6e9fbeb2456b6feec42f97e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Enable Root Port 8 aka 0:0x1c:7
2. Assign free running clock for RP8
3. Apply W/A to get card detected on x1 slot
- Drive OEB 7:GPP_A7 and OEB 6:GPP_E5 low
TEST=Able to detect PCIe SD card over x1 slot
localhost ~ # dmesg | grep mmc
[ 3.643755] mmc0: SDHCI controller on PCI [0000:02:00.0] using ADMA
[ 3.825201] mmc0: new ultra high speed DDR50 SDHC card at address 17f8
[ 3.835452] mmcblk0: mmc0:17f8 SE16G 14.4 GiB
[ 3.849158] mmcblk0: p1
Change-Id: Ibea37b8de4dd020ff0108ec90ea6f8bcfaa4fb17
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48080
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
List of changes in SPD:
1. SPD Revision (of JEDEC spec)
2. SDRAM Maximum Cycle Time (tCKAVGmax) (MTB)
3. MSB -> CAS Latencies Supported, First Byte
4. CAS Latencies Supported, Second Byte
5. CAS Latencies Supported, Third Byte
6. LSB -> CAS Latencies Supported, Fourth Byte
7. Minimum CAS Latency Time (tAAmin)
8. Fine Offset for SDRAM Maximum Cycle Time (tCKAVGmax)
9. Fine Offset for SDRAM Minimum Cycle Time (tCKAVGmin)
10.Cyclical Redundancy Code (0- 125 byte)
TEST=Able to build and boot with updated SPD.
Change-Id: Iae7f2693e87bffb2dfa20bd07b22f4a4768c56cb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
This patch adds LPDDR5 memory configuration parameters to FSP.
TEST=Able to pass FSP-M MRC training on LPDDR5 RVP.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I787bf97dd6c244bd3b0662e5bd061a2da80baa90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Initialize dq_map array in a single line
2. Make dqs_map array also in a single line
TEST=Able to build and boot ADLRVP LP4 SKU.
Change-Id: I64f2b38492934c8ede301f4b252c8700060ed4ac
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48077
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the global variable of a "struct" CBFS file is zero (for example,
CB:47696), the binary will appear in the .bss* section in the ELF file
(instead of .data). This results in an empty binary file added to CBFS,
so that file size check will fail when reading it at runtime.
BUG=b:173751635
TEST=emerge-asurada coreboot
TEST=Check sdram-lpddr4x-KMDP6001DA-B425-4GB is non-empty in CBFS
BRANCH=none
Change-Id: Idfd17d10101a948de0eb0522a672afd5c2f83b04
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47903
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The template for overridetree.cb includes HeciEnabled, which has
been removed from the CNL config struct, so remove it from the
overridetree.
BUG=b:174360951
TEST=`new_variant_fulltest.sh puff` succeeds
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: I87f67c53cc75d9ddd40b4960739180a95de6ecd6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Get rid of variant_gpio_table() and configure GPIOs in gpio.c instead
of passing data around.
Change-Id: Ib158d6bdbcbceb3c1dc4f47fc7c3e098b9c7e5c4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47974
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use include folder for header files allowing proper includes.
Change-Id: I80066fb925b918d040062397e633c5d499a50dbe
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47973
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up the mainboard_ops driver and configure the GPIOs using .init,
since mainboard_silicon_init_params() is meant for the configuration of
the FSP, not the GPIOs.
Change-Id: I6ab8d258c6f81c90d835cb8d07c6387d3de76d85
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47850
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
mainboard_silicon_init_params() is *not* meant for configuring GPIOs. It
should only be used to configure FSP options, which can not be
configured elsewhere.
Change-Id: Ia92d0d173af9c67600e93b473480967304772998
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48008
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix build on Debian/jessie
Change-Id: I987e7a03441b40ab06ccd54a21e38aac81a1c28d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
PICASSO_LPC_IOMUX was only used in the amd/mandolin board, but not in
the corresponding SoC code, so remove it from the SoC's Kconfig and
reanme it in the mainboard's Kconfig to MANDOLIN_LPC.
Change-Id: I261e093d6c56be6073a816b79c60d3a0457616f8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The corresponding functionality in the SoC's Makefile.inc was removed in
commit ef3395d990bbf1118a8d4e367a986bdbc92b1820
Change-Id: Iba84d9deb155ce314b3a3588781752b83a21486b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
There's no need to have the bootblock in its own sub-directory, so move
it to each SoC's main directory to avoid clutter. This makes soc/amd
more consistent with the coreboot code base in src/northbridge,
src/southbridge and src/soc with the exception of src/soc/intel.
Change-Id: I78a9ce1cd0d790250a66c82bb1d8aa6c3b4f7162
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47982
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the drobit variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171947885
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I63b7312bba236bd5af028359804d042f6850d8ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47787
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
show_psp_transfer_info reimplemented the functionality of
transfer_buffer_valid, so use replace that with a function call.
Change-Id: Ie3d373b10bdb0ab00640dabeea12b13ec25406cc
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I4f07d3ab12116229a13d2e8c02b2deb06e51a1af
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I9e9fed26a686b8f90797687dd720902be48dae72
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There will be more files added to the common non-CAR Makefile.inc, so
use an ifeq statement there.
Change-Id: I1f71954d27fbf10725387a0e95bc57f5040024cc
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a Kconfig symbol for including the PCIe MMCONF setup function in the
build and select it when SOC_AMD_COMMON_BLOCK_PCI is selected and in the
southbridges call enable_pci_mmconf(), but don't select
SOC_AMD_COMMON_BLOCK_PCI.
Change-Id: I32de7450bff5b231442f9f2094a18ebe01874ee7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47878
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This pollutes the log on all platforms not implementing an override.
Change-Id: I0d8371447ee7820cd8e86e9d3d5e70fcf4f91e34
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48128
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating Imon slope and offset values as per recommendation of
ODM based on calibaration.
Updating Imon slope to 1.0 and offset to 1.4
BUG=b:167294777
BRANCH=dedede
TEST=Boot dedede platform and confirm values in FSP.
Change-Id: I3eb32218040163f0abef9b8dd4c52efb16289fe7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vinay Kumar <vinay.kumar@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Create the sasuke variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:172104731
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKE
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I29405d63fd266224807e535c3f86a2ad5ab8cdf3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: SH Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Remove the devices unused or not present on this laptop.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I0decad499dfbb5f1e0a189d21f0fca47c80bd490
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:173670150
TEST=Verified that I2C5 frequency is between 386-387kHz.
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I6d60abe15645dc51ed9ee30975d2521b8940c2d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47736
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Similar to the chipset.cb for TGL, this patch gives alias names to all
of the published PCI devices.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6576ef4237c1fc8439795ad5b64b1840504edf73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48009
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Device ID for "D18:F6 - GSPI #2" shoud be 0xA0FB
BUG=none
TEST=Boot to OS, verify SSDT
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I0d814170d24ff1b989eceb1d9ebdf6134df85e2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48060
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6289d2049fbbb6bb532be3d9e2355c563ec98d1b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Tiger Lake introduces new wake-capable devices, including thunderbolt
ports, TCSS XHCI & XDCI as well as DMA ports. Add new ELOG_WAKE_SOURCE
macros for each of these types of devices.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie5dae6514c2776b30418a390c4da53bda0b2d456
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Build using docker results in error: Makefile:86: *** missing separator.
Add space after ifeq.
Tested: Building Facebook FBG1701 binary.
Change-Id: Ib42abe966e67dac380173ec982c9f6bd4cf074cc
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add support for the following 5 LPDDR4x memory parts:
- MT53E512M64D4NW-046 WT:E
- H9HCNNNCRMBLPR-NEE
- MT53D1G64D4NW-046 WT:A
- H9HCNNNFBMBLPR-NEE
- MT53D512M64D4NW-046 WT:F
DRAM Part Name ID to assign
-------------------------------------------
MT53E512M64D4NW-046 WT:E 0 (0000)
H9HCNNNCRMBLPR-NEE 0 (0000)
MT53D1G64D4NW-046 WT:A 1 (0001)
H9HCNNNFBMBLPR-NEE 2 (0010)
MT53D512M64D4NW-046 WT:F 0 (0000)
BUG=b:172993397
TEST=none
Change-Id: Iff8f6257c6cff77fc3f0bda7e75434f9f4de1777
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47981
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add MT53D512M64D4NW-046 WT:F memory part to LP4x global list of
available LP4x parts and to the global JSON file containing LP4x parts
and their characteristics.
BUG=b:172993397
TEST=none
Change-Id: I09c6eab640c169dbdb451964967d14a31e314496
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
This allows dropping ugly preprocessor usage from this file.
Change-Id: Idb66d295129d98725f38d11ac162978418bd94c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Having variants' gpio.c call the `gpio_configure_pads` function results
in an API that does not need to pass data around, which is much simpler.
Change-Id: I1064dc6258561bcf83f0e249d65b823368cf0d31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Most of the existing comments are C-style already.
Change-Id: I9ca4779f5b0560320e9bce4f33e54766522689f9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Print whether the SOC supports TME/MKTME. If the SOC supports the
feature, print the status of enable and lock bit from TME_ACTIVATE
MSR. -t option prints this status.
Sample output:
If TME/MKTME is supported:
============= Dumping INTEL TME/MKTME status =============
TME supported : YES
TME locked : YES
TME enabled : YES
====================================================
If TME/MKTME is not supported:
============= Dumping INTEL TME status =============
TME supported : NO
====================================================
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I584ac4b045ba80998d454283e02d3f28ef45692d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ie347ee508acd900353467b4a3e0a5d1928b110e1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47877
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If there are multiple statements that are conditional on the same
Kconfig option, group them and move the condition check around the
statement. If there's only one statement depending on one condition, use
the short form instead.
Change-Id: I89cb17954150c146ffc762d8cb2e3b3b374924de
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47876
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are sub-directories for both the cache-as-RAM case and the
non-CAR case where the RAM is already initialized when the x86 cores are
released from reset, move the CAR-specific parts of the Makefile.inc to
another Makefile.inc in the car sub-directory. Further patches will add
a Makefile.inc to the non-CAR directory.
Change-Id: I43a3039237d96e02baa33488e71c5f24effe8359
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47875
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit bd31642ad8 (intel/i210: Set bus master bit in command register)
is only necessary because a buggy OS expects Bus Master to be set, not
because the hardware requires Bus Master during initialization. It is
thus safe to defer the Bus Master request into the .final callback.
Change-Id: Iecfa6366eb4b1438fd12cd9ebb1a77ada97fa2f6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47401
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
|
|
There's one copy of this function for all variants except mc_apl4. Move
one copy into common mainboard.c and exit early if running on mc_apl4.
Change-Id: I4e35b58adc074831ccec433b8e014db0695b955e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
A MAC address that is neither 00:00:00:00:00:00 nor ff:ff:ff:ff:ff:ff is
considered valid. Instead of using a temporary buffer and memcmp(), use
a single loop that exits as soon as the MAC cannot possibly be invalid.
Change-Id: I2b15b510092860fbbefd150c9060da38aeb13311
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
Define and use the MAC_ADDR_LEN macro in place of the `6` magic value.
Change-Id: Icfa2ad9bca6668bea3d84b10f613d01e437ac6a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47404
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Break down multi-line compound conditions into multiple if-statements,
and leverage `continue` statements to avoid nesting multiple checks.
Change-Id: I5edc279a57e25a0dff1a4b42f0bbc88c0659b476
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
BUG=b:172528109
BRANCH=firmware-volteer-13521.B
TEST=built and USB3.0, type-c display work.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: Iedf9b972b341064ff62a4443bfa83f69c8c60108
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48066
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates bootblock_pch_early_init() to perform P2SB
configuration before any other PCH controllers are initialized. This
is done because the other controllers might perform PCR settings which
requires the PCR base address to be configured. As the PCR base
address configuration happens during P2SB initialization, this change
moves the p2sb init calls before any other PCH controller
initialization.
BUG=b:171534504
Change-Id: I485556be003ff5338b4e2046768fe4f6d8a619a3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47885
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Able to pass LPDDR5 MRC training with Lp5CccConfig override.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I24b1cf50c1b0b945fce75239bac38e40aeb8a83a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47436
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Able to pass MRC training on DDR4/5 SKUs
Change-Id: I38fcb17a1be5a8544a17cef8255631b6abef0741
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set the FADT PM profile to ENTERPRISE_SERVER, since the currently
supported X11 boards are server boards.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8fb5c7c262fbd3f3c085d7c2e2ef3d6ff6ce73eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48088
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rework gpio setup for the board series to not use headers but
stage-specific compilation units.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ic62ce4335af605c081ef288e892441585ff2bd3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
GPIO needs to be initialized before the IPMI device gets initialized,
so the GPIOs can be read/set by the code in CB:48096 and CB:48094. Thus,
use mainboard_ops.init for GPIO configuration instead of using the
indirection via a mainboard_enable function.
To make it more visible, that we use chip.init, rename `mainboard_init`
to `mainboard_chip_init`.
Tested successfully on X11SSM-F including the IPMI changes.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I192e69a34fa262b38bc40a95fb11c22a4041d0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The ITSS override is not needed for LPC_CLKOUT* pads. Drop it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I3dbbc8944751779151dcd4f92fb870d937801d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48084
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move gpio configuration from the Fsp callback to mainboard init.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If2a54c75c5243d94cdc025c597ee347820b35d32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48086
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop zero-value devicetree options and move PcieRpEnable options down to
the corresponding devices.
Test: built with TIMELESS=1; binaries remain identical
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9285d786e973621a732e2627c734adc930e54207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Commit 056d552 introduced a bug where 0xFF gets set as OC pin value to
supposedly skip programming an OC pin for a disabled USB port. While the
value is correct for the other platforms, Skylake uses 0x08 for this
purpose. Correct this by using the enum value OC_SKIP (0x08) instead.
Change-Id: I41a8df3dce3712b4ab27c4e6e10160b2207406d1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
- Drop issue about non-working TianoCore with Aspeed NGI. see CB:35726
- Add missing reference to X11SSH-F
- Drop TODO reference; there are no TODOs left
Change-Id: I5becfa9ea01a0d9d651c6b51b30ebfcedb6412a5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48101
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the TODO comment, since there is no TODO left. Also drop the now
obsolete TODO section from the board documentation.
Change-Id: I4192aaedc1429c8ff1bd7c52baa4741e1df0d0c5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
- Drop vanished issue on PCIe warning
- Drop TODO section, since the TODOs are done
- Document the jumper J6, that was not documented by the vendor. Its
function has been determined by dissecting a dead board.
- The flash is not socketed anymore. Drop that note and compress the
whole paragraph. Also add a note about flashing via the BMC web
interface.
Change-Id: I2b5a08a6b6d80717621d6a30f31829fe4b84891a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This can be done using in the INTERMEDIATE target in the proper place.
Change-Id: I28a7764205e0510be89c131058ec56861a479699
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46453
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update UPDs required for the creation of DMAR table.
By default coreboot was not generating DMAR table for IOMMU which
was resulting in below error message in kernel:
DMAR: [Firmware Bug]: No DRHD structure found in DMAR table
DMAR: No DMAR devices found
These changes will publish DMAR table through ACPI and will not
result in the above error.
BUG=b:170261791
BRANCH=dedede
TEST=Build Dedede, boot to kernel and check dmesg if DMAR
table exists.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I97a9f2df185002a4e58eaa910f867acd0b97ec2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
The previous commit (that was not touching inteltool.h)
marking internal functions as static is commit 6faccd1f00
Tested on: FreeBSD 13.0-CURRENT r355582
Change-Id: I4aba72f39b528fd70451a4656fd6c835ff766e49
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Move the FSP FD PATH option down, so it gets shown in place of the split
FD files, when the users chooses to use a full FD binary.
Change-Id: Ie03a418fab30a908d020abf94becbaedf54fbb99
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently, setting a custom FSP binary is only possible by using split
FSP-T/M/S FD files. This change introduces the possibility to pass a
combined FD file (the "standard" FSP format).
This is done by adding a new boolean Kconfig FSP_FULL_FD, specifying
that the FSP is a single FD file instead of split FSP-T/M/S FD files,
and making FSP_FD_PATH user-visible when the option is chosen. In this
case, the other options for split files get hidden.
When the user chooses to use a full FD file instead of the split ones,
the FD file gets split during build, just like it is done when selecting
the Github FSP repo (FSP_USE_REPO).
Test: Supermicro X11SSM-F builds and boots fine with custom FSP FD set.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I1cb98c1ff319823a2a8a95444c9b4f3d96162a02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
List of changes:
1. FSP-M Header:
- Adjust UPD Offset for Reservedxx
- Rename UPD Offset UnusedUpdSpace32 -> UnusedUpdSpace29
2. FSP-S Header:
- Rename UPD Offset UnusedUpdSpace46 -> UnusedUpdSpace44
Change-Id: Ia1ef59e4cf6ccce8f48908af51535aea761cd972
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47901
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the galtic variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:170913840
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_GALTIC
Signed-off-by: FrankChu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ie7534d56bc67aca4484f40af1221d669addc01fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47900
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Disable M.2 WWAN and Type-A Port A1
2. Change register 4 to 3 and tuning USB2 Port1 eye diagram
3. Lower camera driving
BUG=b:169105751
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I6b8a5c0d5e814de232d79a43354f5ec0220fc5ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Updating from commit id 9d4053d:
2020-11-20 01:51:08 +0000 - (Revert "Reland: Clean up implicit fall through.")
to commit id 48195e5:
2020-11-24 10:23:45 +0000 - (Makefile: Test for warning flags before using them)
This brings in 3 new commits.
Change-Id: I64f27f346df264cb6eeeb4e3203fcca7d35f7e83
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Commit 82a30a134c (util/crossgcc: Retry package downloads on failure) caused a regression for curl users.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I0d946b86baad3f6409a5042701808da307e5bcb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
RasModesEnabled
Use RasModesEnabled from SystemMemoryMapHob to define SMBIOS type
16 error correction type
Tested=Execute "dmidecode -t 16" to check if error correction type
is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I3636fcc4a874261cf484c10e2db15015ac5d7e68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
Add weak function for SMBIOS type 16 error correction type.
Tested=Execute "dmidecode -t 16" to check if error correction type
is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I85b37e9cfd22a78544d03e5506ff92b1f2404f8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47508
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selecting SOC_INTEL_CSE_LITE_SKU without conditioning on CHROMEOS
force-selects CHROMEOS, per src/soc/intel/common/block/cse/Kconfig.
Conditioning on CHROMEOS allows for non-ChromeOS targets to be built.
Test: build wyvern variant with CONFIG_CHROMEOS=n
Change-Id: I61c9c78a3b02d64bab2813b7a80915b7ecf7f934
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Our current cbfstool has always added a compression attribute to the
CBFS file header for all files that used the cbfstool_convert_raw()
function (basically anything other than a stage or payload), even if the
compression type was NONE. This was likely some sort of oversight, since
coreboot CBFS reading code has always accepted the absence of a
compression attribute to mean "no compression". This patch fixes the
behavior to avoid adding the attribute in these cases.
Change-Id: Ic4a41152db9df66376fa26096d6f3a53baea51de
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It is not used.
Change-Id: I3ef0878811bf2ec406ded03aac6c5dfeb5bf45a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47001
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8694a154d48c5a718b27d4beb858942db0feb997
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I1cc02355e3fea7eb9ad98be6396a492dbbdc47b2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Lindar change amp to ALC1011
Add ALC1011 amp acpi info to devicetree
BUG=b:171771736
BRANCH=firmware-volteer-13521.B
TEST=build and verify ALC1011 can be recognized.
Change-Id: I4d83a19b3baa87cc926bb7c3a2cb96bf3165d2f4
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Change-Id: If74f241b2bb788b3e2fd1b9062fc74819f7be31e
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Add Maxim Polyakov, Nico Huber and Felix Singer as maintainers for
kontron/mal10.
Change-Id: I2f4200708e4aec6d74916fb5e63efe2f20594882
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47889
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some LPC debug boards hard strap SIO address to be at
0x164e/0x164d vs 0x4e/0x4d. Add support for configurable
SIO address to support these cards.
BUG=b:159933344
TEST=boot with LPC debug card, verify serial output
Change-Id: I103c61f21f13970dfa3b9a788b29964e478fb84c
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add H5ANAG6NCJR-XNC.
BUG=b:165461530
BRANCH=volteer
TEST=emerge-volteer coreboot
Change-Id: I827158ce0abe764f1e3b5de46abf50dc148a6ff0
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Save for the IO_APIC2_ADDR definition, they are equivalent.
Change-Id: I14da3d9aeefcc725428957ce0c9ac164eabacec6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47408
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only two definitions are actually used somewhere, the rest is unused.
Change-Id: Iec52d0d47fce6a1ec5455b670824b995a7a34a4c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47407
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up the mainboard_ops driver and configure the GPIOs using .init,
since mainboard_silicon_init_params() is meant for the configuration of
the FSP, not the GPIOs.
Change-Id: I82f1eaf6693d9b117fb211776047058cdc787288
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I008de1bf91ba97ee5eefbde11947c73059fff5f7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: Id73a7385f7701920efebaa3e293ac50a6ba93272
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47849
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace hard-coded IDs with defines introduced in CB:47807.
Used documents:
- 328904-003
- 329003-003
Built lenovo/t440p with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I910ab356dd8728c316018989bfb2689d4c67c2dc
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47808
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used documents:
- 328904-003
- 329003-003
Change-Id: I95790cda6f7c42a9de57bf5e92eb829ee1807dbe
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47807
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This option only applies to boards using the Lenovo H8 EC code.
Change-Id: I3b16a61a0aa9f51a4061b1b5e58fc276e7383415
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47150
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only Sandy Bridge MRC stores scrambler seeds in CMOS. Non-Sandybridge
boards ended up with these entries because of copy-paste programming.
Change-Id: I5a5bda6ea4e63ba03a4219bb2a6aa546bb6ecd7a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47149
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
update the DPTF parameters received from the thermal team.
BUG=b:167523658
TEST=emerge-volteer coreboot
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Iafc3fb389ade5cfec79a816a28880262bdce7c74
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47858
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SMI handler was not installed for Xeon_sp platforms. This enables SMM
relocation and SMI handling.
TESTED:
- SMRR are correctly set
- The save state revision is correct (0x00030101)
- SMI's are properly generated and handled
- SMM MSR save state are not supported, so relocate SMM on all cores
in series
- Verified on OCP/Deltalake mainboard.
NOTE:
- Code for accessing a CPU save state is not working for SMMLOADERV2,
so some SMM features like GSMI, SMMSTORE, updating the ACPI GNVS
pointer are not supported.
- This hooks up to some soc/intel/common like TCO and ACPI GNVS. GNVS
is broken and needs to be fixed separately. It is unknown if TCO is
supported. This might require a cleanup in the future.
Change-Id: Iabee5c72f0245ab988d477ac8df3d8d655a2a506
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46231
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TCO is configured by FSP. This mostly makes it possible to report TCO
events in SMM if enabled.
Change-Id: I4f81c7888e45ed01ee68b1d6e6a9986a4d735467
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47764
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The soc code was already there but it was never linked.
Change-Id: I75ee08dab524bc40f1630612f93cbd42025b6d4e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds three settings for the new sd readers.
The new assigned values are:
1. RTS5227S: 3
2. L9750: 4
3. SD_OZ711LV2LN: 5
BUG=b:173676531
BRANCH=volteer
TEST=abuild -t google/volteer
Change-Id: I595695f99d3298f146fcdb7c2b942ce007ae9327
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Allows advertising support for a 1ch array DMIC in the NHLT table.
Boards use the NHLT if a microphone is connected to the DSP.
Tested on an Acer Aspire VN7-572G (Skylake-U) on Windows 10.
A custom ALSA topology will be required for Linux.
Change-Id: Idba3a714faab5ca1958de7dcfc0fc667c60ea7fd
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
According to the NHLT specification[1], PDM_DEV is defined as "1" on
Kabylake based platforms. coreboot currently sets it to "0" on
all platforms. Add an entry to the enum and use it to define
NHLT_PDM_DEV for Kabylake.
"Device Type" will resume from "2" on all platforms, but entries are
currently reserved.
Tested on an Acer Aspire VN7-572G (Skylake-U), which has a 1ch array
DMIC, on Windows 10.
1. https://01.org/sites/default/files/595976_intel_sst_nhlt.pdf
Change-Id: Ifbc67228c9e7af7db5154d597ca8d67860cfd2ed
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45010
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow the example of newer AMD code for Stoneyridge and Picasso.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I9c17d4cb4953b28a47483f5d7db308ccc89e9281
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Following the example of CB:7630 done for family16kb boards
(git commit 3ff4f85ccd9fdb7cd4885a10f025b5ab297a445f).
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Ic48c7475ceadb60f825ca9e3c3427c8a7525a266
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
