| Age | Commit message (Collapse) | Author |
|---|
|
Currently, to enable/disable LTE based on fw_config on nissa, we have
two sets of GPIOs: lte_enable_pads and lte_disable_pads. This was to
prevent the SAR interrupt pin GPP_H19 from floating for the short period
of time between enabling it in gpio.c and disabling it in fw_config.c
(see CB:64270 for more details).
With the new pad-based GPIO overrides (CB:64712), this is no longer an
issue since the gpio.c and fw_config.c overrides are applied at the same
time. So simplify the LTE GPIO configuration by enabling all the LTE
pins in the variant gpio.c, then disabling them in fw_config.c if
needed.
BUG=b:231690996
TEST=LTE still works on nivviks
Change-Id: I5bf20a027414ea5e7c1f198d69e355c76f467244
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66776
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the SoC that was upstreamed as Sabrina was finally renamed to
Mendocino, also adjust the abbreviation used for the DXIO/DDI descriptor
struct array names.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I14ecf98e4a94376a70e783774c8f7b8701581220
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66815
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The flag EC_BATT_FLAG_CUT_OFF was added with the CL:
3704470: battery: Set battery cutoff flag
https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/3704470
This flag is set in the ACPI memory mapped area when the command
`ectool batterycutoff` is issued so ACPI code can respond
appriopriately. This CL adds the flags to coreboot ACPI.
BRANCH=none
BUG=b:217911928
TEST=Boot nipperkin with low & no battery
TEST=Boot skyrim with low & no battery
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I4e63ff4fc2d6b0ecf767a6bffd81f823c74c15bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66803
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I added this header in commit a6c8b4becbd12fe6043557ca1e398c1a7c691007
(nb/intel/sandybridge: Rewrite get_FRQ). Relicense it as "BSD-3-Clause
OR GPL-2.0-or-later" and move it into the BSD-licensed commonlib part.
Change-Id: I89ebdcdf8d06e78e624e37a443696981b3b17b7d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66711
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the Shadow Registers from 2 through 5 and print information
from them accordingly. All values were taken from Intel document
number 571993.
Tested on the StarLite Mk III and the correct values are
shown:
[DEBUG] CSE: IBB Verification Result: PASS
[DEBUG] CSE: IBB Verification Done : YES
[DEBUG] CSE: Actual IBB Size : 88
[DEBUG] CSE: Verified Boot Valid : FAIL
[DEBUG] CSE: Verified Boot Test : NO
[DEBUG] CSE: FPF status : FUSED
Please note, the values shown are in an error state.
This replaces the Fuse check that is done via Heci, as this will only
work whilst the CSE is in a normal state.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I8a9e7b329010fae1a2ed9c3fefc9765e617cdfe4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
coreboot is unable to disable certain devices, whilst many are hidden
DPTF and SMBus are not. Set this to enabled chipset so that it is
enabled by default.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I85d74179b6fe3c6126566422f82f7b806f80d0c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add supported memory parts in mem_parts_used list, and generate SPD ID
for these parts.
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
H9JCNNNBK3MLYR-N6E 0 (0000)
H58G56AK6BX069 2 (0010)
K3LKBKB0BM-MGCP 2 (0010)
BUG=b:242277219
BRANCH=None
TEST=run part_id_gen to generate SPD id
Change-Id: I46c168482113beb7cd28f387ed495847aba8602f
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Create the yaviks variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:242277219
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_YAVIKS
Change-Id: Id60fe0e54a8e0196a302141f58c6695779ac251a
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Build error for platforms using Intel FSP for TGL_IOT (FSP_TYPE_IOT). File FirmwareVersionInfoHob.h does not exist in Intel FSP TGL IOT package.
File FirmwareVersionInfoHob.h is included when DISPLAY_FSP_VERSION_INFO is enabled. Enable this config for non TGL_IOT only.
BUG = NA
TEST = Verify that DISPLAY_FSP_VERSION_INFO is disabled by default for TGL_IOT
configuration (Build Siemens AS_TGL1).
Change-Id: Ief5a7222daf6f1658e8dc04f97b4ddc2bcb74905
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66636
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Mendocino has more eSPI decode ranges than Picasso or Cezanne. To
support these additional ranges, introduce a new Kconfig option
SOC_AMD_COMMON_BLOCK_ESPI_EXTENDED_DECODE_RANGES that can be selected by
the SoCs that support the additional eSPI IO/MMIO decode ranges.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib761cdf201c35805d68cf5e8e462607ffd9fa017
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add GPIO configuration and device tree to enable the chip.
BUG=b:240607130
BRANCH=firmware-brya-14505.B
TEST=Patch linux with NXP's pending drivers
UWB device is probed and can respond to a simple hello packet
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I83be712d243c365a5cbfe6f69a6bd85440c5bec7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The patch updates the comments on return values and heci_reset()
triggering during error scenarios of heci_receive() and heci_send()
functions to reflect the current implementation.
Test=Build the code for Gimble
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I6c6c3312602c772147cb315db9ea1753d84a0fb3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: Ib97d009c056b487136f20e5341b31183c65ef761
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This wasn't done previously because not all files in the
src directory had the correct headers. Doing this earlier
would have broken the build.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: Ia6d7a7a17116e4c8e55354783085355fd45ff87a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66505
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to 8
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
- Set pre-wake randomization time (DPA) to 100
BUG=b:241349500
TEST=build FW and checked fsp log.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Id4a1540de8c3ee74695631acc8181dcc446fe137
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66783
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add FW_CONFIG probe based on pujjoteen boxster of below devices:
LTE, SD card, stylus, WFC camera, AUDIO
BUG=b:236158122
TEST=Boot to OS and verify that above devices are set based on
fw_cofnig.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I49fc5461e7affba68a6b89bf166c84598fbfa088
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66741
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ghost has two amps and address are 0x3c and 0x3d.
BUG=b:231581723
BRANCH=firmware-brya-14505.B
TEST=max98396 driver can get the DSD property correctly.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I3b6a331ca42e97f984f3a585726c02452bb067f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add MAX98396 support.
BUG=b:232606045
TEST=build passed.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I835b51ea1fcc9363992d43a625f80cb545802fc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Starting vboot earlier in bootblock instead of romstage is usually
preferred (smaller root of trust, among other things). Therefore
unselect VBOOT_STARTS_IN_ROMSTAGE for broadwell. Also remove the unused
BROADWELL_VBOOT_IN_BOOTBLOCK option.
Change-Id: If8feea403ee4cd3a16ed8cb0faf9f4ccb34feaaf
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This reverts commit f87489bbae5bb1ae3b17b6a03af9e309769b1f72.
Reason for revert: Broadwell actually supports early flash writes.
Change-Id: I342aefe464c72a32b41a40062b62d871caa0707b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The I2C config was unnecessarily placed in the overridetree. As we
prepare for fanout, this is going to cause unnecessary noisy changes.
Move the I2C config to the devicetree to avoid this.
BUG=None
TEST=Build
Change-Id: I09ad5c911a0fd00274761cb71e9b659b47cd6da1
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66802
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PCIe spec explicitly states that the bottom-two bits of the next
offset are reserved for future use and should be masked. We can also
change the loop condition to avoid wrong offsets below 0x100 (exten-
ded capabilities always reside in the extended config space).
The whole patch series was tested on Google Samus and keeps the L1ss
configuration of the WiFi device in tact.
Change-Id: I0b622a0ce0a4a1127d266226ade0ec1e66e9fb79
Signed-off-by: Nico Huber <nico.h@gmx.de>
Tested-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66459
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add some inline functions for the bit-wise operations, change the loop
body to an if-bail-out style and remove stateful variables.
Change-Id: Ia8db915f375737064e3486d313383d9b6c3eb2b8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66458
Reviewed-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Keeping these checks in generic code seems rather dangerous.
In theory, it could lead to endless loops even for compliant
devices, if we accidentally detect arbitrary register contents
as capability and use them as a pointer to another one. Not
to forget that the register reads can have side effects.
All users of this `cafe` have been converted to use
pciexp_find_ext_vendor_cap().
Change-Id: I70d21534e04282a4156572a290b83c46be085e0c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66456
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We have this quirk in our tree since the introduction of L1-substate
support[1]. The way we searched for this capability was rather crude:
We simply assumed that it would show up in the first data word of
another capability.
As it turned out that it is actually a proper vendor-specific capa-
bility that we are looking for, we can drop some of the mystic code.
This was confirmed to work on the device that was originally used
during development, Google/Samus.
[1] commit 31c6e632cf (PCIe: Add L1 Sub-State support.)
Change-Id: I886fb96e9a92387bc0e2a7feb746f7842cee5476
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Vendors can choose to add non-standard capabilities inside a
Vendor-Specific Extended Capability. These are identified by
the Extended Capability ID 0x0b.
Change-Id: Idd6dd0e98bd53b19077afdd4c402114578bec966
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Move the `offset` parameter into pciexp_find_extended_cap(). If it's
called with `0`, we start a new search. If it's an existing offset,
we continue the search.
This makes it easier to search for multiple occurences of a capa-
bility in a single loop.
Change-Id: I80115372a82523b90460d97f0fd0fa565c3f56cb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Now that we have functionality to get the minimal and nominal
frequencies, the corresponding fields in the CPPC config can now be
populated. If the HOB isn't present and/or the frequency values
could not be obtained, CPPC_UNSUPPORTED is still used; otherwise the
HOB-provided frequency in MHz is used for those two fields.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Change-Id: Id3257690a3388d44ceceb7ac4f1db3d49e195caa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66551
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add common AMD FSP functionality to get the nominal and minimal CPU core
CPPC frequencies. Those functions will be used in the _CPC ACPI object
generation in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Change-Id: I68ebdf610795d2673e0118a732f54f5f719b73c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66550
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
xhci.asl places the SS ports at 11-14, following HS ports 1-10. However,
for Nissa, the kernel detects 12 HS ports 1-12 and 4 SS ports at 13-16,
resulting in the PLD intended for SS ports 1 and 2 being associated with
HS ports 11 and 12.
Changing the asl for SS to 13-16 makes locations associate correctly and
peering work.
BUG=b:234544025
BRANCH=firmware-brya-14505.B
TEST=manually verified on Nissa and Brya devices
Change-Id: I57aef771a7ff086b71a9e90b81e1a3635f832b2f
Signed-off-by: Adam Mills <adamjmills@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66590
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SMI sleep entry handler will access the SMN space via the index/data
register at PCI config space offsets 0xb8 and 0xbc of the device at bus
0, device 0, function 0. This register pair is also used by other
software components running on the x86 cores after boot, so it should be
saved and restored at the beginning/end of the SMI handler if it
accesses SMN. The sleep entry SMI handler is a special case, since the
OS is already done at the moment we enter the sleep SMI handler which is
the last code that gets run on the x86 cores before entering S3/4/5.
BUG=b:237004699
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0980562ef8a61489082a81c71d6d00d0786d68cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
EN_PP3300_EMMC will change to GPP_A21 to meet DP++ function and it based on Moli GPIO Table_20220803.xlsx. But it will let current eMMC skus can't boot into OS, so use the board_ver to decide which gpio table return and set override_gpio_table_id2 and early_gpio_table_id2 based on Moli GPIO Table_20220803.xlsx
1. set GPP_A21 to EN_PP3300_EMMC
2. set GPP_A22 to NC
3. set GPP_E20 to DDIC_DP_CTRCLK
4. set GPP_E21 to DDIC_DP_CTRLDATA
BUG=b:241370405
TEST=emerge-brask coreboot
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I0a2c8684d140738f43658cd6075ed083eee44e65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
This patch calls into a helper function to fill `2nd microcode loading
FSP UPD` if FSP is running CPU feature programming.
TEST=Able to build and boot Google/Kano.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8534305e4e973c975ad271b181a2ea767c840ae3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66686
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the winterhold variant of the skyrim reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:240970782
BRANCH=None
TEST=util/abuild/abuild -p none -t google/skyrim -x -a
make sure the build includes GOOGLE_WINTERHOLD
Signed-off-by: Isaac Lee <isaaclee@google.com>
Change-Id: I0e16f0a674aa3f4687cd82d5840a3c2087148a51
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66620
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit I73b7ddec50936f7836f915f459ca0bdc0777cb22.
Revert change to disable post codes. Post codes were initially disabled
because of an issue with initialization within the SMU.
BUG=b:227201571
TEST=Build and boot to OS in Skyrim.
Change-Id: I2a2bd2252a103c682b5d4ad5ecd1da42b3744083
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66092
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board is no longer in the tree.
Change-Id: Ie4a626ce85fe0dc2b2d826dd8830a8e80ec331aa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
By moving the large wait for FBVDD discharge from PGOF
to PGON, the whole time may be avoided if enough time has
elapsed between the successive calls.
BUG=b:239719056
TEST=With Nvidia test software, verify ACPI prints
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I891aa14f120d58c45b8965038a9d2f2a417b3f3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Now that the virtual wire situation is figured out, the GC6 sequence
is updated to match the latest HW design guide from Nvidia. This
allows Nvidia test software to (mostly) successfully execute the GC6
test, but with some PCIe AER errors.
BUG=b:214581763
TEST=tested with Nvidia test software
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ia094c4fa9b4db094a59b9b6f02be1a649ee8569b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Since the VW GPIOs are not in the baseboard GPIO table, they do
not actually override anything, and hence do not actually get
programmed. This patch moves the programming from the ramstage
table to the bootblock table so they get programmed.
BUG=b:214581763
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.corp-partner.google.com>
Change-Id: I42db44d38df20dd2695921e2f252be163f6b17f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It is highly unlikely that the "OEM revision" of the DSDT is 0x20110725
on mainboards with a chipset not yet released on 2011-07-25. Since this
comment is most likely to have been copy-pasted from other boards, drop
it from boards which use a chipset newer than Sandy/Ivy Bridge.
Change-Id: If2f61d09082806b461878a76b286204ae56bf0eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
These comments don't add much value, so remove them.
Change-Id: I7e9692e3fe82345cb7ddcb11c32841c69768cd36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66713
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
This patch drops explicit usage of the address-of operator ('&') while
passing the function pointer (argument 0) to the
`mp_run_on_all_cpus` API.
Note: It's just cosmetic change without any real difference in the operation.
TEST=Able to build and boot Google/Kano where CPU feature programming
is successful on all logical processors.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2c77959a76d2240ad1bfb7a9d7b9db7e8aee42f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66685
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
If we already encountered the last extended capability in the
list, we'd call pciexp_get_ext_cap_offset() with `offset == 0`.
So it also needs to check if the passed offset is valid.
As there were no callers of pciexp_find_next_extended_cap()
yet, pciexp_get_ext_cap_offset() was only ever called with
`PCIE_EXT_CAP_OFFSET`.
Change-Id: I155c4691a34ff16661919913a3446fa915ac535e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Checking if the return value of the fsp_find_extension_hob_by_guid call
is NULL should make the code a bit easier to read.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6bdb07eab6da80f46c57f5d7b3c894b41ac23b8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Different guybrush boards have different TPM IRQs. This change passes in
the correct GPIO to the TPM.
BUG=b:241824257
TEST=Boot guybrush and verify GPIO 3 was passed and that OEM Crypto test
passes
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I61954fa4493fd56e528b616ca65166a31917f557
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The PSP currently uses a hard coded GPIO for the TPM IRQ. Not all board
versions use the same GPIO. This method allows the mainboard to pass
in the correct GPIO.
BUG=b:241824257
TEST=Boot guybrush and verify PSP message prints
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie05d095d7f141d6a526d08fbf25eb2652e96aa49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Since bootblock_soc_early_init gets called before
bootblock_mainboard_early_init which does the early GPIO setup, external
I2C level shifters that are controlled by GPIOs might not be enabled yet.
Moving the reset_i2c_peripherals call to bootblock_soc_init makes sure
that the early GPIO setup is already done when reset_i2c_peripherals is
called.
Haven't probed any SCL signal on the non-SoC side of the I2C level
shifters yet, but the waveform on the SCL pin of I2C3 on the SoC of a
barla/careena Chromebook doesn't have the longer than expected SCL
pulses any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If02140aef56ed6db7ecee24811724b5b24e54a91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Logo.bmp is overwritten with a custom one from coreboot. This needs to
be restored before the branch is updated otherwise git will report that
the repository is dirty.
Move this to the update recipe so that will always be done for any
recipe that needs to update the branch.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I85bf753a47d9e70d6555dec9a539e8ed7395bead
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66355
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust an ASCII art table so that it looks good: consistent padding and
aligned table borders.
Change-Id: I26196f969406e03f320256b0c3a337282f636914
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66707
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Steelix uses ps8640 for board revision < 2, and uses anx7625 for newer
revisions. So we use board_id to distinguish anx7625 and ps8640.
BUG=b:242018373
TEST=firmware bootsplash is shown on eDP panel of steelix.
Change-Id: Ia6907d2e6e290375946afb13176ab9a26dedd671
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@chromium.org>
|
|
BUG=b:232302324
TEST=Validated on qualcomm sc7280 development board
Observing 9th bit of skuid with below values,
1 means Modem device
0 means non-modem device
Signed-off-by: Venkat Thogaru <quic_thogaru@quicinc.com>
Change-Id: If62b272a43a4588f96e49c8b2b1d75862d401d31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add support for SocInfo in coreboot. The API socinfo_modem_supported is
added to help to differentiate between LTE and WiFi SKUs.
BUG=b:232302324
TEST=Validate boards are detected correctly on LTE and Wifi SKUs
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Change-Id: I61047ad49772c3796ba403cafde311ad184a4093
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add a new driver for NXP UWB SR1xx (e.g., SR150) device.
The driver was originally written by Tim Wawrzynczak as a WIP in
CL:3503703, and was based on drivers/spi/acpi.
BUG=b:240607130
BRANCH=firmware-brya-14505.B
TEST=On ghost (with follow-up CL), patch linux with NXP's pending
drivers
-> UWB device is probed and can respond to a simple hello
packet
Co-authored-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I5b1b0a5c1b48d0b09e7ab5f2ea6b6bc2fba2a7d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66466
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add OV 5675 MIPI camera to ghost, sensor eeprom, and IPU device to
device tree. Enable config for MIPI camera.
BUG=b:241343306
BRANCH=firmware-brya-14505.B
TEST=with ghost overlay changes, camera in camera app works
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: Ie079e43ae0f34efba396331922ea4a89eda72128
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit 8b1c6c6cb384c89659abbd043c2566df358d8f95. With
updated APCB, eSPI configuration carries over to bootblock. Hence eSPI
does not need to be re-initialized in bootblock.
BUG=b:241426419
TEST=Build and boot to OS in Skyrim with PSP verstage.
Cq-Depend: chrome-internal:4929421
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I426b07329d4a0154d915381c99dcc9746b7a3d7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Introduce the `BROADWELL_LPDDR3` Kconfig option along with some wrapper
code to allow mainboards using LPDDR3 DRAM to supply the DQ/DQS maps to
chipset code without having to use `pei_data`. The only mainboard using
LPDDR3 is Google Samus.
Change-Id: I0aaf0ace243c03600430c2a7ab6389a7b20cb432
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55812
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Mainboards do not need to know about `pei_data` to tell northbridge code
where to find the SPD data. As done on Haswell, add the `mb_get_spd_map`
function and the `struct spd_info` type to retrieve SPD information from
mainboard code without having to use `pei_data` in said mainboard code.
Unlike Haswell MRC, Broadwell MRC uses all positions of the `spd_data`
array, not just the first. The placeholder SPD address for memory-down
seems to be different as well. Adapt the existing code to handle these
variations. Once complete, the abstraction layer for both MRC binaries
will have the same API.
Change-Id: I92a05003a319c354675368cae8e34980bd2f9e10
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
The `ddr_refresh_2x` setting is already set in chipset code.
Change-Id: I76478689b3aa27c369a0413d9fbde03674d5e528
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55810
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no generic way to tell whether a mainboard has an EC or not.
Making Kconfig symbols for these options seems overkill, too. So, just
put them on the devicetree. Also, drop unnecessary assignments when the
board's current value is zero, as the struct defaults to zero already.
Change-Id: I8d3b352333bea7ea6f7b0f96d73e6c2d7d1a2cfb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55809
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
The SPD file handling code is generic and can be used on any other
mainboard. Move it to chipset scope to enable code reuse.
Change-Id: I85b1460ccb82f0c1bf409db4a6b4c9355c25e76d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55808
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Introduce the `SPD_MEMORY_DOWN` macro to indicate that a slot is used
with memory-down. This enables computing the channel disable masks as
the bits for slots where the SPD address is zero. To preserve current
behavior, zero the SPD addresses for memory-down slots afterwards.
Change-Id: I75b7be7c72062d1a26cfc7b09b79de62de0a9cea
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55807
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is the version of genrelnotes that was used to help with the
4.16 release.
- Fix shellcheck issues.
- Send messages for the user to STDERR.
- Add recent platforms
- Handle symbolic links to the git repo.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I2204793a5d1cc5792d0720d2bbfb172bb6020dd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
To generate a complete _CPC ACPI object, coreboot needs the minimal and
nominal core speed values which are specific to the CPU and not only the
CPU family. Since this is done by an undocumented mechanism, FSP has to
do this and puts the information we need into a HOB. This adds the HOB
GUID and the structure of the HOB data.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Change-Id: Ibf338c32de367a3fd57695873da1625338fa196d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66549
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the path after the chip keyword needs to point to the directory
that contains the chipset's chip.h file, change this from
soc/amd/rembrandt to soc/amd/mendocino.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I63334fbd59e74df491035b5cf7e296818cc02665
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66688
Reviewed-by: ritul guru <ritul.bits@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
These files contain no creative content, and therefore have no
copyright. This effectively means that they are in the public
domain.
This commit updates the unlicensable empty (and effectively empty)
files with the CC-PDDX identifier for license compliance scanning.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I0b76921a32e482b6aed154dddaba368f29ac2207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66497
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for signed 64-bit division. The implementation mostly
relies on __aeabi_uldivmod, which is already implemented.
ldivmod.S was adapted from CrOS EC version of ldivmod.S:
https://chromium.googlesource.com/chromiumos/platform/ec/+/main/third_party/libaeabi-cortexm0/core/cortex-m0/ldivmod.S
The CrOS EC version was adapted from:
https://github.com/bobbl/libaeabi-cortexm0/blob/master/ldivmod.S
BUG=b:240316722
BRANCH=None
TEST=Signed division works in PSP verstage (runs on ARM)
Change-Id: I53785c732b0fa35a4809bc054f1482c5461ada7b
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
A 32-bit long storing microseconds will rollover every ~1.19 hours.
This can cause stopwatch to misbehave, causing unexpected failures.
If the current field in stopwatch is near 2^31, the expires field may
rollover when initialized. If this occurs, stopwatch_expired() will
instantly return true.
If current and expires fields are near 2^31, the current field could
rollover before being checked. In this case, stopwatch_expired() will
not return true for over an hour. Also stopwatch_duration_usecs() will
return a large negative duration.
This issue has only been observed in SMM since it never takes more
than 35 minutes to boot.
Switching to uint64_t mitigates this issue since it will not rollover
for over 500K+ years. The raw TSC would rollover sooner than this,
~200 years, depending on the tick frequency.
BUG=b:237082996
BRANCH=All
TEST=Boot Nipperkin
Change-Id: I4c24894718f093ac7cd1e434410bc64e6436869a
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65403
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Move the code that prints the edk2 build options to it's own recipe
so that it can be called for different targets.
This change also fixes the print, as it accounts for recent switches
such as `--pcd` and `-s`.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie797ca26cd28eab0f633bd8dee5ec19634fcea99
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
DFD (Design for Debug) is a debugging tool, which scans flip-flops
and dumps to internal RAM on the WDT reset. After system reboots,
those values can be shown for debugging using MTK internal parsing
tools.
TEST=build pass
BUG=b:236331724
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: I6d19dc6f4e47ed69ba2ea87c79984020a413aee9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66586
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We use the same dump address and size for DFD in all MediaTek SoCs, so
we move them to dfd_common.h and rename dfd_common.h to dfd.h.
TEST=build pass
BUG=b:236331724
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: I162bbb0a82e3b55c8cfbbd20e28a54ad01fd6b0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66585
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=build pass
BUG=b:236331724
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: Ie9d7b361dda8c5850bc0682c255bc20f9e26675c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66668
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tracker is a debugging tool. When bus timeout occurs, the system will
reboot and latch some values of tracker registers which could be used
for debugging.
This function will be triggered only when it encounters the bus
hanging issue.
TEST=build pass
BUG=b:236331724
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: I78f676c08ea44e9bb10bd99bbfed70e3e8ece993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66584
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This replaces 'SPDX-License-Identifier' tags in all the files under
soc/mediatek/mt8188 for better code re-use in other open source
software stack.
These files were originally from MediaTek and follow coreboot's main
license: "GPL-2.0-only". Now MediaTek replaces these files to
"GPL-2.0-only OR MIT" license.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Change-Id: If61e8b252400e8e5ecd185b6806b1ca279065f15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66628
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
A power and performance analysis performed on Alder Lake demonstrated
that with an EPP (Energy Performance Preference) at 50% along with
EET (Energy Efficient Turbo) disabled, the overall SoC performance are
similar or better and the SoC uses less power.
For instance some browser benchmark results improved by 2% and some
multi-core tests by 4% while at the same time power consumption
lowered by approximately 7.6%.
Similar results are observed on Raptor Lake.
BRANCH=firmware-brya-14505.B
BUG=b:240669428
TEST=verify that EPP is back to the by default 50% setting
`iotools rdmsr 0 0x774'
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: I735ad9d88c7bf54def7a23b75abc4e89a213fb61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhixing Ma <zhixing.ma@intel.com>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 938f33e9f7756d730a1da278679087476a476bf2.
A power and performance analysis performed on Alder Lake demonstrated
that with an EPP (Energy Performance Preference) at 50% along with
EET (Energy Efficient Turbo) disabled, the overall SoC performance are
similar or better and the SoC uses less power.
For instance some browser benchmark results improved by 2% and some
multi-core tests by 4% while at the same time power consumption
lowered by approximately 7.6%.
BRANCH=firmware-brya-14505.B
BUG=b:240669428
TEST=verify that EPP is back to the by default 50% setting
`iotools rdmsr 0 0x774'
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: Icacc555e62533ced30db83e0a036db1c85c0bfa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhixing Ma <zhixing.ma@intel.com>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 844dcb3725fc95df53a7229703f5059d2c36f98e.
A power and performance analysis performed on Alder Lake demonstrated
that with an EPP (Energy Performance Preference) at 50% along with
EET (Energy Efficient Turbo) disabled, the overall SoC performance are
similar or better and the SoC uses less power.
For instance some browser benchmark results improved by 2% and some
multi-core tests by 4% while at the same time power consumption
lowered by approximately 7.6%.
BRANCH=firmware-brya-14505.B
BUG=b:240669428
TEST=verify that ETT is disabled
`iotools rdmsr 0 0x1fc'
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: I96a72009aaf96d4237d57f4d5c8b1f41f87174d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66281
Reviewed-by: Zhixing Ma <zhixing.ma@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for taniks board. Please refer Intel doc#723158 for
more information.
BUG=b:241965786
TEST=Verify on taniks boards.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: Ib95430c7ba9d84f8bafcb1febcff9b4e4038cadc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Moli has 90W adapter for 15W SOC and 135W adapter for 28W SOC, so modify the Psys_PL2 for both 15W and 28W SOC.
-set 90W Psys_PL2 for 15W SOC
-set 135W Psys_PL2 for 28W SOC
BUG=b:242119726
TEST=emerge-brask coreboot
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: If8f9006d797d74f6d5d802d445edc425a4700420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Unassigned tag is defined to emulate an unmapped PCI BAR resource.
This resource is not mapped into host physical address and hence
should not be picked up by memranges_add_resources().
Change-Id: If7a5c437d486b80d798496b985efd80526f13c63
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Dabros <jsd@semihalf.com>
|
|
It's possible that some BARs are not got their resource successfully
mapped, e.g. when these BARs are too large to fit into the available
MMIO window.
Not assigned resources might be with base address as 0x0. During
global resource search, these not assigned resources should not be
picked up.
One example is MTRR calculation. MTRR calculation is based on global
memory ranges. An unmapped BAR whose base is left as 0x0 will be
mistakenly picked up and recognized as an UC range starting from 0x0.
Change-Id: I9c3ea302058914f38a13a7739fc28d7f94527704
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66347
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
IORESOURCE_ASSIGNED is used to indicate the resource is actually mapped
host physical address space. E.g. PCI BAR resources not mapped are
not regarded as assigned.
In src/include/device/device.h, standard macros, e.g. ram_resource,
mmio_resource, io_resource, et al, are all following the usage above.
This patch updates the bootmem-test and memrange-test to follow the
usage as well.
Change-Id: Ifc19302482038267cef01321a46a72d90ca76d35
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66450
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Jan Dabros <jsd@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I251840b409dead62586cefe5856b6c544401ba30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Enable CRB_TPM to allow the use of the fTPM (Intel PTT).
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I7b69854ea636947480402ce12450f431028660a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
coreboot uses TianoCore interchangeably with EDK II, and whilst the
meaning is generally clear, it's not the payload it uses. EDK II is
commonly written as edk2.
coreboot builds edk2 directly from the edk2 repository. Whilst it
can build some components from edk2-platforms, the target is still
edk2.
[1] tianocore.org - "Welcome to TianoCore, the community supporting"
[2] tianocore.org - "EDK II is a modern, feature-rich, cross-platform
firmware development environment for the UEFI and UEFI Platform
Initialization (PI) specifications."
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I4de125d92ae38ff8dfd0c4c06806c2d2921945ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65820
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The Cezanne CPPC ACPI table generation code also applies to Sabrina, so
move it to the common AMD SoC code directory so that it can be used for
Sabrina too.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5ce082a27429948f8af7f55944a1062ba03155da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66400
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This reverts commit Ic152c295954d33ef1acddb3b06f0c6bbfbfb38ae.
There was a bug that caused the SMU to hang when writing port80. it has
since been resolved, so revert this workaround.
BUG=b:227201571
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I5f10e282ab03756c7dbfb48182940f979eb122e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66470
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
We want to extend the vb2ex_hwcrypto APIs on the vboot side to allow
passing 0 for the data_size parameter to vb2ex_hwcrypto_digest_init()
(see CL:3825558). This is because not all use cases allow knowing the
amount of data to be hashed beforehand (most notable the metadata hash
for CBFS verification), and some HW crypto engines do not need this
information, so we don't want to preclude them from optimizing these use
cases just because others do.
The new API requirement is that data_size may be 0, which indicates that
the amount of data to be hashed is unknown. If a HW crypto engine cannot
support this case, it should return VB2_ERROR_EX_HWCRYPTO_UNSUPPORTED to
those calls (this patch adds the code to do that to existing HW crypto
implementations). If the passed-in data_size value is non-zero, the HW
crypto implementation can trust that it is accurate.
Also reduce a bit of the console spew for existing HW crypto
implementations, since vboot already logs the same information anyway.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ieb7597080254b31ef2bdbc0defc91b119c618380
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Found by:
find payloads/libpayload/drivers/usb -type f -name "*.[ch]" | xargs \
util/lint/checkpatch.pl --types SPACING -q --fix-inplace -f
Change-Id: Id23e2e573e475c6d795812a4b2df9aeffbcaaaf4
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66596
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for taeko board. Please refer Intel doc#723158 for
more information.
BUG=b:241965786
TEST=Verify on taeko/tarlo boards.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I03042906d5bea9b9010016adb98fbe68e2dc92f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
When removing SD card from USB card reader, the USB MSC stack does
not detach the device immediately. Instead, the USB MSC stack calls
usbdisk_remove() and calls usb_msc_destroy() after several pollings.
It results in usbdisk_remove() being called twice.
Since the usbmsc_inst_t instance is freed after first usbdisk_remove()
call, the second call invokes an invalid usbmsc_inst_t instance and
causes exception in CPU.
This patch prevents usbdisk_remove() from being called twice by setting
usbdisk_created to zero.
BUG=b:239492347
TEST=insert an empty SD card into the USB card reader then remove
the SD card. AP firmware does not crash.
Change-Id: I0675e9fde3e770d63dd0047928356a204245ef18
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66449
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When powering down SSUSB, the system needs to wait the ACK from SSUSB.
We found that the setting of USB PAD top macro is not correct and
it will cause timeout waiting for the ACK from SSUSB.
To resolve this, we add mt_pll_set_usb_clock() in pll.c to enable usb
macro control for powering down SSUSB.
TEST=timeout of ssusb powerdown ack does not occur.
BUG=b:239634625
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.corp-partner.google.com>
Change-Id: I58ba86e0467284e9947bfda1005c151a3e0c8881
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66600
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add new ram_id:0001 for memory part H9HCNNNCPMMLXR-NEE.
BUG=b:241494931
TEST=none
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Iee9f881d8ab21396d208a6af9f0cec8414cb50a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
- ADP_P_* -> RPP_S_* (got mixed up I guess)
- Remove duplicates of ADP_S_ESPI_*
- Add infix _ESPI_ to all ADP_S device ID's
Document: 619362
Change-Id: Ic18ecbd420fc598f0ef6e3cf38e987ac3ae6067e
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66629
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
R680E, Q670E, H610E are the ADL-S IoT variants
TEST=Boot ADL-S RVP DDR5 and see silicon info is reported
as PCH: AlderLake-S R680E
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I1804994b4b72f0484eabb15323736679d2668078
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change provides access to IOE through P2SB Sideband interface for
Meteor Lake TCSS functions of pad configuration and Thunderbolt
authentication. There is a policy of locking the P2SB access at the end
of platform initialization. The tbt_authentication is read from IOM
register through IOE P2SB at early silicon initialization phase and its
usage is deferred to usb4 driver.
BUG=b:213574324
TEST=Built coreboot and validated booting to OS successfully on MTLRVP
board. No boot hung was observed.
Change-Id: Icd644c945bd293a8b9c4a364aaed99ec4a7c12f9
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Delete the Thunderbolt authentication function ioe_tcss_valid_tbt_auth
from the common block. Meteor Lake Platform will implement it.
BUG=b:213574324
TEST=Built coreboot image successfully.
Change-Id: I97a289faa6351fe562f91d8478b72c9403ce88cb
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
DDR5 memory modules have two separate 32-bit channels (40-bit on ECC
memory modules), and the SPD info refers to one channel: the primary
bus width is 32 (or 40) bits and the "DIMM size" is halved. On Alder
Lake, there are 2 memory controllers with 4 32-bit channels each for
DDR5. FSP has 16 positions to store SPD data, some of which are only
used with LPDDR4/LPDDR5.
To try to make things less confusing, FSP abstracts the DDR5 channels
so that the configuration works like on DDR4. This is done by copying
each DIMM's SPD data to the other half-channel. Thus, fix the wrapper
parameters for DDR5 accordingly.
Tested on AlderLake-P DDR5 RVP (board ID 0x12), both DIMM slots now
function properly. Without this patch, only the top slot would work.
Change-Id: I5f01cd77388b89ba34d91c2dc5fb843fe9db9826
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66608
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use the actual model name for the variant dir.
Change-Id: I199b8efb5c3cddb8943ba4b761546caa11c67a30
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Enable RFIM Policy, request by RF team.
BUG=b:239657092
TEST=emerge-nissa coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Id0f425d75a1ac9486a9284d4e8320ba4c63b182f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Consolidate MAX_BIOS_ENTRIES and MAX_PSP_ENTRIES definitions into one
file
Signed-off-by: Altamshali Hirani <al.hirani@amd.corp-partner.google.com>
Change-Id: Ie3c64a1875010e7fb368967283df6baf1cc7ba8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62911
Reviewed-by: ritul guru <ritul.bits@gmail.com>
Reviewed-by: Bao Zheng <fishbaozi@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
