Age | Commit message (Collapse) | Author |
|
the limit. It is done by reading the register whose device address is 0xC. It is not trivial as it looks.
Signed-off-by: Maggie Li <maggie.li@amd.com>
Reviewed-by: Joe Bao <zheng.bao@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
See details at:
http://support.necam.com/mobilesolutions/hardware/Desktops/pm2000/celeron/
Thanks to Quentin RAMEAU <quentin.rameau@gmail.com> for providing the
required information and for testing the patch.
This boots into a Linux console just fine.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3800 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This patch adds SB700 support to flashrom. The code for enabling the flash
rom is the same as for SB600. It was tested (read, write, verify) with an
ASUS M3A-H/HDMI which contains a Macronix MX25L8005.
Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3799 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Thanks to Niels Ole Salscheider for the problem report.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3798 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
flashrom used to exit 0 even if erase failed. Not anymore.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3797 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The patch changes the LDTSTOP length as well mostly default content of 0xec,
0xe4 and 0xe5 registers. I'm suspecting that the documentation may be wrong.
Furthermore this fix for powernow may not work on CPUs hit by errata #181.
Workaround should be implemented. The powernow may not work on pre-A2 revisions
of VT8237S silicon, revision reg is unknown.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3796 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
0xe4 and 0xe5 registers. I'm suspecting that the documentation may be wrong.
Furthermore this fix for powernow may not work on CPUs hit by errata #181.
Workaround should be implemented. The powernow may not work on pre-A2 revisions
of VT8237S silicon, revision reg is unknown.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
* PMBASE dumping now knows the registers.
* Add support for i965, i975, ICH8M
* Add support for Darwin OS using DirectIO
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3794 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
SST_25VF512A_REMS
SST_25VF010_REMS
SST_25VF020_REMS
SST_25VF040_REMS
SST_25VF040B_REMS
SST_25VF080_REMS
SST_25VF080B_REMS
SST_25VF032B_REMS
SST_26VF016
SST_26VF032
W_25X16
W_25X32
W_25X64
Straight from the data sheets.
The REMS IDs help in case the RDID opcode is unavailable (due to opcode
lockdown) or unsupported by the chip.
Some day, we need to pair probe functions together with IDs. Multiple
pairs can exist per chip and duplicating chip definitions does not
really make sense.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3793 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Bug from r3791.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3792 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
If flashbase was set before probe_flash() it would only ever be used once, for
the very first flash chip probe.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3791 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
fixes #109
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3790 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
make sure the temporary files are created in the same directory as the
target files so they can be rename()d. This fixes a compilation issue on
machines with the build directory living on another partition than /tmp.
Pretty trivial.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3789 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Add AMD dbm690t ACPI support.
The following ACPI features are supported.
1. S1, S5 sleep and wake up (by power button or PS/2 keyboard/mouse).
2. AMD powernow-k8 driver.
3. Thermal configuration based on ADT7461.
4. IDE timing settings.
5. HPET timer.
6. Interrupt routing based on ACPI table.
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3788 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The following ACPI features are supported.
1. S1, S5 sleep and wake up (by power button or PS/2 keyboard/mouse).
2. AMD powernow-k8 driver.
3. Thermal configuration based on ADT7461.
4. IDE timing settings.
5. HPET timer.
6. Interrupt routing based on ACPI table.
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3787 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3785 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
hwmon has generic registers and banked registers, mostly temperature
handling, and SMI/GPIO stuff.
Not all LDNs are switched via register offset 0x07, make it a parameter.
Add support for dumping the hardware monitor of Winbond W83627THF/THG
parts with the -e option.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3784 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- create temp files and move them afterwards
- remove dummy option -b
- fix usage
- drop implicit creation of .c file if no --option is specified.
Now let's see if this fixes the issue. :-) We don't want to take 24s
instead of 6s to build an image reliably (Yes, yes, I know Tiano takes
over 20 minutes)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3783 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jason Wang<Qingpei.wang@amd.com>
Reviewed-by: Joe, Bao <Zheng.Bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3782 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3781 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
unsupported functions, giving the user the impression that the
unsupported functions are tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3780 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This has been tested by Uwe Hermann on an RS690/SB600 board.
Signed-off-by: Jason Wang <Qingpei.Wang@amd.com>
Reviewed-by: Joe Bao <zheng.bao@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3779 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
With this patch it's possible to
- determine the according source code line for each asm statement
(objdump -dS)
- determine the source code file for each asm statement
(objdump -ddl)
This isn't exactly trivial because cache_as_ram_auto.c gets compiled to
assembly and converted by a perl script afterwards.
This patch solves the problem
- by extending cache_as_ram_auto.inc with debug information and line
numbers
- by correcting the perl calls (".text" --> "\.text")
- by creating a disassembly with source code and line numbers.
(ctr0.disasm and
coreboot.disasm)
There's one minor downside to the patch: A complete abuild run takes up
around 1.6G instead of about 700MB now. But I'm sure this is quite
reasonable for the benefits.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Please commit while this is being worked out.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
running twice at the same time, overwriting its output files. This caused
a depending rule to produce an object file with no symbols in it.
This should silence up the regularly happening build failure messages on
the mailing list since we moved to the newer, much faster server.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3777 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is the first chip which uses the infrastructure for alternative
erase commands, namely spi_chip_erase_60_c7().
Signed-off-by: Jason Wang <Qingpei.Wang@amd.com>
Reviewed-by: Joe Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- probe_spi_rdid with opcode 0x9f, usually 3 bytes ID
- probe_spi_res with opcode 0xab, usually 1 byte ID
We are missing the following probe function:
- probe_spi_rems with opcode 0x90, usually 2 bytes ID
RDID provides best specifity (manufacturer, device class and device) and
RES is supported by quite a few old chips. However, RES only returns one
byte and there are multiple flash chips with different sizes on the
market and all of them have the same RES ID.
REMS is from the same age as RES, but it provides a manufacturer and a
device ID. It is therefore on par with the probing for parallel flash
chips and specific enough.
The order in which chips should be detected is as follows:
1. RDID
2. REMS
3. RES
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
which support all commands, but may not exist.
For controllers which support only a subset of commands, it will fail in
unexpected ways. Even if a command is supported by the controller, it
may be unavailable if the controller is locked down.
The new logic checks if RDID could be issued and its return values made
sense (not 0xff 0xff 0xff). In that case, RES probing is not performed.
Otherwise, we try RES.
There is one drawback: If RDID returned unexpected values, we don't
issue a RES probe. However, in that case we should try to match RDID
anyway.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: FENG yu ning <fengyuning1984@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3774 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
memory controller.
Also, drop some unused '#if 0' code.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3773 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is a trivial patch.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3772 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
After running make clean, most of build/ directory gets deleted.
It is (re)created in the "prepare" make target, but that was libpayload.a
dependency after the $OBJS, while OBJS building already needs to dump its
created object files there.
Simply rearrange the make target dependencies to get at least "make clean;make" working.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3771 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
And some more notes in TODO.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3770 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
File util/flashrom/flash.h already had correct ID for that part.
Signed-off-by: Tero O Peippola <xeropp@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3769 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Rename the generated config file to libpayload-config.h to differenciate
it from other config.h files. Move the default location of the file to
$(src)/include so that LIBPAYLOAD_PREFIX= users can access the file
without staging it.
Signed-off-by: Jordan Crouse <jordan@cosmicpenguin.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3768 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3767 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
msrtool can decode MSRs and print the value of every field in human
readable form. It can also be used to save a set of MSRs to a file,
and at a later time compare the saved values with current values in
hardware.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3766 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
as well as most (all?) combinations thereof.
Drop some unused code, the unused row_offset variable, and obsolete comments.
Also, fix a typo (thanks to Stefan Reinauer for noticing).
This is tested on the MSI MS-6178 with a number of different DIMM
combinations and so far all of them worked fine.
Signed-off-by: Elia Yehuda <z4ziggy@gmail.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3765 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Intel 810 chipset (and all boards using it). This isn't required for this
chipset as there's only one memory controller.
This also helps a lot with romcc register usage, you should see the dreaded
"too few registers" less often.
Build-tested with all three boards using the Intel 810 chipset.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3764 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
don't have one (by fixing it for amd/serengeti_cheetah and copying the
same file to all other broken targets)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3763 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is a school book example of why trivial indent patches just suck
big time.
This error was introduced by a trivial self-acked indent patch and was
never detected (because of a missing Config-abuild.lb)
So, indenting the code for no reason can make it a lot worse (read:
break it) instead of improving it.
I ask everyone to keep this in mind when going on indent-frenzy again.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3762 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the Lippert Cool SpaceRunner LX which is already in svn).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3761 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- PC/104+ form factor
- AMD Geode-LX CPU/northbridge
- AMD CS5536 southbridge
- ITE IT8712F superio
http://www.lippert-at.com/index.php?id=408
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3760 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
values for different DIMM configurations. This should be converted to a
table or code later on and actually be used for BUFF_SC.
Many thanks to Elia Yehuda <z4ziggy@gmail.com> for testing and collecting
the table entries.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3759 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
SPI opcodes should be placed in which location. Move to a less
optimistic implementation and actually use the generic SPI read
functions. They're useful for abstracting exactly this stuff and that
makes them the preferred choice.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3758 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
does not have a mechanism to signal command failure, the SPI host may be
unable to send a given command over the wire due to security or hardware
limitations. The current code ignores these mechanisms completely and
simply assumes almost every command succeeds. Complain if SPI command
execution fails.
Since locked down Intel chipsets (like the one we had problems with
earlier) only allow a small subset of commands, find the common subset
of commands between the chipset and the ROM in the chip erase case. That
is accomplished by the new spi_chip_erase_60_c7() which can be used for
chips supporting both 0x60 and 0xc7 chip erase commands.
Both parts of the patch address problems seen in the real world. The
increased verbosity for the error case will help us diagnose and address
problems better.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Otherwise: Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3757 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
AT25DF021
AT25DF041A
AT25DF081
AT25DF161
AT25DF321A
AT25DF641
AT25F512B
AT25FS010
AT25FS040
AT26DF041
AT26DF081A
AT26DF161
AT26DF161A
AT26DF321
AT26F004
I double-checked the data sheets and am confident this will work.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3756 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Tested fully on a ThinCan DBE61A
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3755 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The AT45 series SPI chips are DataFlash EEPROMs which means they have
odd (non-power-of-two) sector sizes, but some of the DataFlash chips can
be configured or ordered with power-of-two sector sizes.
Add probe support for the following Atmel SPI chips:
AT25DF021
AT25DF041A
AT25DF081
AT25DF161
AT25DF321A
AT25DF641
AT25F512B
AT25FS010
AT25FS040
AT26DF041
AT26DF081A
AT26DF161
AT26DF161A
AT26DF321
AT26F004
AT45CS1282
AT45DB011D
AT45DB021D
AT45DB041D
AT45DB081D
AT45DB161D
AT45DB321C
AT45DB321D
AT45DB642D
Add an explanation why the following chips can't be probed:
AT45BR3214B
AT45D011
AT45D021A
AT45D041A
AT45D081A
AT45D161
AT45DB011
AT45DB011B
AT45DB021A
AT45DB021B
AT45DB041A
AT45DB081A
AT45DB161
AT45DB161B
AT45DB321
AT45DB321B
AT45DB642
Add the ID, but no probing function for this chip:
AT25F512A
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andriy Gapon <avg@icyb.net.ua>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3754 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, use the more generic and buildrom-friendly '../payload.elf' as
the default payload location.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3753 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3752 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
duplicate strings to save some space.
Signed-off-by: Marc Jones <marcj303@yahoo.com>
Acked-by: Chris Lingard <chris@stockwith.co.uk>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
IT8780F, and Fintek F71863FG.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3750 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3749 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3748 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3747 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3746 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Robert Millan <rmh@aybabtu.com>
Acked-by: Jordan Crouse <jordan@cosmicpneguin.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3745 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Rename the "coreboot" menu "firmware", and add a module to parse
the multiboot table. For now, just parse memory, but it can be
expanded as needed.
Signed-off-by: Jordan Crouse <jordan@cosmicpenguin.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Add a new infrastructure for returning system information to payloads.
First up - a pointer to the multiboot table.
Signed-off-by: Jordan Crouse <jordan@cosmicpenguin.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3743 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
enable may do printk()s which result in a 2 minute delay on some boards.
Fix this on all boards which currently do smbus_enable() before enabling
the serial console.
Thanks to Elia Yehuda <z4ziggy@gmail.com> for tracking this bug down.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3742 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
* fix \r\n occurence in i945 code
* drop early TOLUD write
* fix 16bit BCTRL1 access
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3741 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, add missing C1DRA2 #define (as per public datasheet).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3738 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Per report from Mario Rogen. Thanks!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3736 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ulf Jordan <jordan@chalmers.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3735 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3734 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, fix BIOS_CNTL, which is 0xdc on ICH7.
Build-tested with kontron/986lcd-m.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3733 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ICH7 southbridge (but it might work with ICH4/ICH5 or so).
The ICH7 needs a different init code. Drop the non-working code for now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
erase and write by Stéphan Guilloux.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3731 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
as well.
Replace age-old TODO comments with real explanations.
Fixed chips:
Fujitsu MBM29F400TC (ID definition)
Macronix MX29F002T (chip name)
New chips:
Fujitsu MBM29F004BC
Fujitsu MBM29F004TC
Fujitsu MBM29F400BC
Macronix MX25L512
Macronix MX25L1005
Macronix MX25L2005
Macronix MX25L6405
Macronix MX29F002B
Straight from the data sheets, compile tested only.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3730 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Compile error in filo.c if AUTOBOOT_DELAY=0. Replace
#ifndef AUTOBOOT_DELAY
with
#if !AUTOBOOT_DELAY
which should work for both the #undef and the =0 case.
In ext2fs.c, fat.c
#if ARCH == 'i386'
results in a compile warning: "multi-character character constant" and
the condition ARCH == 'i386' is mis-evaluated as FALSE, eventually
choking the assembler on a PPC instruction. Change it to
#ifdef __i386
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3729 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
boards need them to switch the com ports from RS232 to RS485.) The PnP
resources should prevent other devices from being mapped at the same
spot, even if no OS driver actively uses them.
The IT8712F manual makes it look like PNP_IO1 had a size/granularity of
1 byte, but that must be a mistake. The Simple-I/O resource has a size
of 5 bytes (1 for each GPIO set 1-5) and trying different addresses
reveals a granularity of 8.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3728 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3727 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3725 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Not tested, builds, derived from getpir. Definitely better than what was there.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3724 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This helps a lot if we have to track down configuration weirdnesses.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3723 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
flashrom. Not all chips support all commands, so allow the implementer
to select the matching function.
Fix a layering violation in ICH SPI code to be less bad. Still not
perfect, but the new code is shorter, more generic and
architecturally
more sound.
TODO (in a separate patch):
- move the generic sector erase code to spi.c
- decide which erase command to use based on info about the chip
- create a generic spi_erase_all_sectors function which calls the
generic sector erase function
Thanks to Stefan for reviewing and commenting.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3722 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
opcode instead.
This is slightly slower (ha, ha), but works on boards with a locked opmenu. Tested on ICH7 and works.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3721 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, fix a few Makefiles regarding lzma stuff and 'make clean' behaviour.
Add bayou.xml.example which users can use as a starting point.
Bayou does compile fine now (if you build ../libpayload) before.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3720 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
on the last snapshot posted by Jordan Crouse. This commit is long
overdue.
Changes by me include:
- Rename 'utils' to 'util' for consistency with our other projects.
- Move the main code out of src/* into the top-level directory.
- Add missing license headers to the following files:
Makefile, pbuilder/liblar/Makefile, util/pbuilder/Makefile.
- Dropped the util/pbuilder/lzma completely. I'm working on reusing
the lzma/ dir from v3 via svn:externals. Alas, this also means
that Bayou won't yet compile out of the box.
- Coding-style and white-space fixes (indent) for all files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to only a set of reasonably similar ones, namely (for now) ICH0* - ICH6*,
and C-ICH.
All later ICH* southbridges (ICH7-ICH10) are _very_ different and were surely
not working with this driver anyway (and there's no chance to support
them reasonably with this driver without ending up in #ifdef hell).
ICH7 now has an extra driver in svn, whether ICH8-ICH10 are similar
enough to be supported by that ICH7 driver remains to be seen.
This patch was informally acked by Stefan Reinauer
<stepan@coresystems.de> on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
erase/write are not implemented.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
tested and
Acked-by: Elia Yehuda <z4ziggy@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3717 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3716 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Build-tested on kontron_986lcd_m.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3715 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
as we've done with the superiotool and flashrom manpages, too (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3714 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3713 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
pass with toolsets that compile larger images. (trivial)
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3712 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to 1M.
Both regular and abuild images have been boot tested successfully.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3711 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- PC/104+ form factor
- AMD Geode-LX CPU/northbridge
- AMD CS5536 southbridge
- ITE IT8712F Super I/O
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3710 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Andriy Gapon <avg@icyb.net.ua>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3709 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- SST SST39SF010A
- Winbond W29C011
Tested by me on actual hardware, all operations.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3708 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
using block erase d8 as discussed with Peter Stuge
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3707 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(trivial).
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Acked-by: Ed Swierk <eswierk@aristanetworks.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Build-tested with the kontron/986lcd-m target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3705 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3704 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3702 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This includes an early SMI handler.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|