Age | Commit message (Collapse) | Author |
|
There are four chipsets selecting PMC_GLOBAL_RESET_ENABLE_LOCK but only
one (apollolake) is actually calling the code. Add the missing call.
Change-Id: I6aba9bcb2ad09e6ae0e02d8c0b552e34bdb3fa72
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36571
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make use of the new ETR address API in the ETR3 register related
functions.
Further, disabling and locking of global reset is now done at once to
save one read-modify-write cycle, thus the function was renamed
accordingly and the now redundant disabling in soc/apl got removed.
Change-Id: I49f59efb4a7c7d3d629ac54a7922bbcc8a87714d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add soc implementation for the new ETR address API.
Change-Id: Iae54af09347d693620b631721576e4b916ea0f0f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a comment to the newly introduced MMIO address helpers for PCI
config registers, that the pointer returned may change during the boot
processs and, thus, must not be cached.
Change-Id: Ieb90ae9d67a3b944d35587dec54756a17c27c86f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add VBT file extracted from vendor (AMI) firmware,
use by default to ensure functional display after
resume from S3 when using libgfxinit.
Test: build/boot Librem 13v1/15v2 boards, verify
functional display after resume from S3 when using libgfxinit.
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Change-Id: I44d75486da3083cd1f07ea82dc18688db84a621e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36916
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO49 is strapped high, so setting it low likely increases power
usage. GPIO53 is hooked to a testpad so there is no reason to set
it here.
Change-Id: I00fb38c90417b673c2b36191c20279474eb0dc21
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Create new variant for jinlon
BUG=b:144150654
TEST=emerge-hatch coreboot chromeos-bootimage and boot on jinlon proto
board
Change-Id: I8deb29041475e38cbbf2f54519940f62b9f21822
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36681
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Perform EC software sync in romstage, before memory training is started.
Because the ChromeOS EC will not currently perform USB-PD negotiation
until it jumps to running its RW code, this allows the system to get
access to more power earlier in the boot flow.
This is guarded by CONFIG_VBOOT_EARLY_EC_SYNC.
BUG=b:112198832
BRANCH=none
TEST=EC software sync works in update and non-update case.
No significant effect on boot time (~6 ms).
Change-Id: I31f3407a2afcbf288461fab1397f965f025bc07c
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36211
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, depthcharge and coreboot are using two different vboot libraries.
coreboot is using "fwlib20", while depthcharge uses "fwlib". The only
difference between the two libraries is the inclusion of vboot1-only
compilation units in fwlib, which are now deprecated. Therefore, coreboot
may as well use fwlib too. Vboot is expected to converge on a single firmware
library soon.
BUG=none
BRANCH=none
TEST=compiles and runs verstage correctly
Change-Id: I905b781c3596965ec7ef45a2a7eafe15fdd4d9cc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36341
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating from commit id ecdca931:
2019-11-13 06:14:05 +0000 - (vboot: move vb2_context inside vb2_shared_data (persistent context))
to commit id 1c4dbaa0:
2019-11-19 06:31:23 +0000 - (Makefile: Fix typo for MOCK_TPM)
This brings in 17 new commits.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1952d7a26725e2c008b5009705b2e78ac0bb82df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36936
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add 4 new timestamps to the EC software sync flow:
1) Beginning of EC software sync
2) EC finished calculating Vboot hash
3) EC is no longer requesting power limiting
4) End of EC software sync
BUG=none
BRANCH=none
TEST=verified timestamps show up in cbmem log
Change-Id: I6e5703c146b5ec27d01700fdb39cb3d2092ea8a8
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Use the new functions introduced into the EC driver to support
performing EC software sync via vboot callbacks.
NOTE: This patch assumes that the EC image is added to CBFS
uncompressed. Streaming decompression of the image will be added in a
future patch.
Also adds a new Kconfig option VBOOT_EARLY_EC_SYNC. The new Kconfig
option compiles EC software sync into romstage, dependent upon having a
CrOS EC.
BUG=b:112198832
BRANCH=none
TEST=Successful EC software sync
Change-Id: I9b1458a45ab3ed5623af50f78036c4f88461b226
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36208
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop struct cbfs_props and replace with struct region_device object.
The goal of the cbfs locator APIs are to determine the correct region
device to find the cbfs files. Therefore, start directly using struct
region_device in the cbfs location paths. Update the users of the API
and leverage the default boot region device implementation for
apollolake.
Change-Id: I0158a095cc64c9900d8738f8ffd45ae4040575ea
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Since we already have pre-RAM cache for FMAP (CB:36657), calling
load_firmware() multiple times is no longer a problem. This patch
replaces vboot_get_selected_region() usage with vboot_locate_firmware(),
which locates the firmware by reading from the CBMEM cache.
In addition, returning false from vboot_is_slot_selected() implies the
recovery path was requested, i.e., vb2_shared_data.recovery_reason was
set. Therefore, we simply remove the vboot_is_slot_selected() check from
vboot_check_recovery_request().
BRANCH=none
BUG=chromium:1021452
TEST=emerge-kukui coreboot
Change-Id: I27cb1a2175beb189053fc3e44b17b60aba474bb0
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Since buffer_size is no longer used, remove it from struct
vboot_working_data.
BRANCH=none
BUG=chromium:1021452
TEST=emerge-kukui coreboot
Change-Id: Ie770e89b4a45e0ec703d5bbb8fb6a298ce915056
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
With removal of Torpedo mainboard, this code is no longer
necessary. Will resolve some unique Coverity issues.
Change-Id: I2927245c426566a8f80863a109d015ebf6176803
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
With removal of Torpedo mainboard, this code is no longer
necessary. This also removes fam12 support from northbridge
and SB900 from southbridge.
Change-Id: I8a30461278844d0d9ad4320f0e952774c4fd644f
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This also permits removal of vc/amd/agesa/f12, as it was the only
mainboard using it. That will in turn allow resolving some unique
Coverity issues reported against that source.
Change-Id: I73f570f01fcb5ba0e306508a569ea97f432596b3
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I063997d51a80b1b244a0cb35ae90446610ef2c21
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36975
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7102519b171c3e5269fefaa66d12d605f5d9ddb5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36974
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The MIPS architecture port has been added 5+ years ago in order to
support a Chrome OS project that ended up going nowhere. No other board
has used it since and nobody is still willing or has the expertise and
hardware to maintain it. We have decided that it has become too much of
a mainenance burden and the chance of anyone ever reviving it seems too
slim at this point. This patch eliminates all MIPS code and
MIPS-specific hacks.
Change-Id: I5e49451cd055bbab0a15dcae5f53e0172e6e2ebe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34919
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After removing urara no board still uses this SoC, and there are no
plans to add any in the future (I'm not sure if the chip really exists
tbh...).
Change-Id: Ic4628fdfacc9fb19b6210394d96431fdb5f8e8f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36491
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board never really existed and nobody has any hardware left over
for it.
Change-Id: Icdba4f5209725995e4a55dcdbc299a9e91a5869a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Remove vboot_named_region_device(_rw) and use
fmap_locate_area_as_rdev(_rw) directly.
BRANCH=none
BUG=none
TEST=emerge-kukui coreboot
Change-Id: I244ac4e01ae5b80285162b3baffc0b30aa057bfb
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fill in some stats using our repo analysis scripts in
util/release/, thank the contributors, add some prose
about notable achievements since 4.10.
Also start a new doc for 4.12.
Change-Id: I10a39081762d6e01f4040f717d36662975e4c8e9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36948
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The mainboard was accidently added due to bad rebase.
Change-Id: Ie7215e551651dbbc8d92316c48e455405923a30b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36077
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This uses less lines, is the original Markdown syntax, and for short
blocks better readable.
Change-Id: Id96ad0f65980dfb943eef3cde5626d56f97622f9
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35729
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Run
- make -C util/docker doc.coreboot.org to build the docker image
- make -C util/docker docker-build-docs to build the documentation
- make -C docker-livehtml-docs to serve autoupdated documentation over
http://0.0.0.0:8000
Change-Id: Ic07f216f8d90d6e212383250b852dc91575304c3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36104
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I24c4254ef65edcddadcf0386e0cbe996a5e99458
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This config is a slightly stripped configuration of the Chromium OS
configuration used in production. Apparently the bootblock fills up
faster than usual on this device, resulting in address overflows.
Add this config here so we'll notice early in the future.
Change-Id: I3145bba63d32ddb9d00fd98d3cb774bf9ddd69a6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36923
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
By removing this code, we get approximately back to
where the board was before the fmap cache feature
was added, which is small enough for the Chromium OS
default configuration for the board to fit into the
32KB that the bootblock can use on the chipset again.
Change-Id: I52c0c30a14929913ded144bf086c12938e9c2699
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
FSP2.0 forces MRC retraining on cold boot on Intel SPS systems.
Change-Id: I3ce812309b46bdb580557916a775043fda63667f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Correct what looks to be errant characters in the makefile variable for
the Gigabit Ethernet Controller. This should have no effect on any
mainboards as none select the HUDSON_GEC_FWM symbol.
Change-Id: Icb861d872973aaf2b653440cae00057d5ad89b20
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Due to the way CAR teardown is handled in FSP 1.0, the results of
car_get_var_ptr() aren't always reliable, which can break things when
running with FMAP cache. It might be possible to fix this but would make
the code rather complicated, so let's just disable the feature on these
platforms and hope they die out soon.
Also allow this option to be used by platforms that don't have space for
the cache and want to save a little more code.
Change-Id: I7ffb1b8b08a7ca3fe8d53dc827e2c8521da064c7
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
With GCC 9.x has a new warning *address-of-packed-member*.
> -Waddress-of-packed-member
>
> Warn when the address of packed member of struct or union is
> taken, which usually results in an unaligned pointer value.
> This is enabled by default.
This results in the build errors below, for example, with GCC 9.2 from
Debian Sid/unstable.
src/southbridge/intel/common/spi.c: In function 'spi_init':
src/southbridge/intel/common/spi.c:298:19: error: taking address of packed member of 'struct ich7_spi_regs' may result in an unaligned pointer value [-Werror=address-of-packed-member]
298 | cntlr->optype = &ich7_spi->optype;
| ^~~~~~~~~~~~~~~~~
Therefore, explicitly disable the warning.
Change-Id: I01d0dcdd0f8252ab65b91f40bb5f5c5e8177a293
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36940
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
buffer_to_fifo32() is a simple wrapper to buffer_to_fifo32_prefix(), but
unfortunately its arguments are swapped. This patch fixes the issue.
Change-Id: I6414bf51dd9de681b3b87bbaf4ea4efc815f7ae1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36942
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch moves the traditional POSIX stdbool.h definitions out from
stdint.h into their own file. This helps for using these definitions in
commonlib code which may be compiled in different environments. For
coreboot everything should chain-include this stuff via types.h anyway
so nothing should change.
Change-Id: Ic8d52be80b64d8e9564f3aee8975cb25e4c187f5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch changes the ipq40xx Makefile.inc to follow established
coreboot practice of calling Python scripts directly rather than
invoking the 'python' interpreter explicitly. This has the added effect
of honoring the scripts shebang (which in this case is set to
'python2').
Change-Id: If96e8313527c411ef1bb6386e03b6a209c750131
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Some types of Undefined Behavior can be determined statically at compile
time and gcc now has a set of flags that make it emit warnings in that
case instead of doing the __builtin_trap() / optimize / UD2-opcode dance
that silently breaks the resulting binary.
BUG=chromium:958270
BRANCH=none
TEST=abuild passes (probably not)
Change-Id: I3aa5ca00c9838cc7517160069310a1ef85372027
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
IASL reports unnecessary/redundant use of offset operator. These
messages are only masking usefull messages.
Add -vw 2158 so this message isn't reported.
BUG=N/A
TEST=build
Change-Id: Ie8507d3b3cb6f2e75cb87cd3e4bcc4280df27f77
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36857
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some Sandy Bridge boards disabled the PCI-to-PCI bridge early to avoid
probing by the MRC. We can do that for all boards instead, based on the
devicetree setting.
Change-Id: Ie64774628fde77db2a379bdba6a921a31e52fa0d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The integrated GbE port is toggled via the Backed-Up Control (BUC)
register. We already disable it according to the devicetree setting
but never enabled it. This could lead to the confusing situation
that it was disabled before (different build, vendor BIOS, etc.)
but shouldn't be anymore.
As we need a full reset after enabling GbE, do it in early PCH init.
Change-Id: I9db3d1923684b938d2c9f5b369b0953570c7fc15
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This is supported by generic PCH code now.
Change-Id: Id5d764c97e47cdb08a68d03002ebebd996769914
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The BUC register is actually only 8 bits wide and setting bit 5
(disabling GbE) is already done by generic code.
Change-Id: I729a2a28f4b0d94eddd070dc89b7341ac0c35e4a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Don't overwrite the LPC decode config of the generic PCH code, move
UART init into bootblock_mainboard_early_init() and don't enable the
IOAPIC, which is already done by generic code.
Change-Id: I90d090f5bff29174e68981fea3c3f04c666b1d28
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The BUC register is actually only 8 bits wide and setting bit 5
(disabling GbE) is already done by generic code.
Change-Id: I4b8e14606c319e8bfc48d6757087f28af1bd5dfb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Move UART initialization to bootblock_mainboard_early_init() and don't
override the generic LPC decode settings.
Change-Id: Icdab36ae0324175d3d51a050784b94a53d4b3b7c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The BUC register is actually 8 bits wide and shouldn't be bluntly
cleared.
Change-Id: I2ffd2d161005e839e730102b56af4f66efeb551e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Only set LPC decode bits that the generic PCH code doesn't set yet. And
don't enable the IOAPIC, which is already done by generic code.
Change-Id: I9d2f6a9ad3f5d83573e07596f2763edc75f4ee64
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This bit is already cleared by a reset.
Change-Id: Ib71496011c9621476a7327ba309f367c7fa971e4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This bit is used to indicate xHCI routing across reboots. If anything,
coreboot should act on it, not set it during boot. ASL code would be
supposed to set it.
Change-Id: Id14647ac4e591cfa042ca8aad6dfc6ccda35c74a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The generic PCH code already enables a superset of LPC decoding. Move
UART setup to bootblock_mainboard_early_init() where it is expected.
Last but not least, remove an odd write to BUCs (RCBA+0x3414) and
beyond, as it's an 8-bit register and shouldn't be bluntly zeroed.
Change-Id: I24a4ccf6a529460a83f48522d2e05e6ad6614f81
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The generic PCH code already sets up a superset of these decodings.
Change-Id: I90bca37c46b89c35f323225fc3c087f1630397e4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
mainboard_pch_lpc_setup() and mainboard_late_rcba_config() did 4
things here on top of the generic PCH code:
1. Enabling LPC decoding for gameports. It seems unlikely
that anything is using these ports and there is no code
to support gameports.
2. Decoding of COM3 instead of COM2. What COM?
3. Premature locking of ETR3/global reset. Bad idea.
4. Disabling the GbE port in BUC. Already done by PCH code.
Change-Id: Ie92dbf5c6813435995c4d24ed807ffc8d125953a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ia041b63201b2a4a2fe6ab11e3497c460f88061d1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I198709efe1eb5d2022d0fbd640901238e696eaa6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
There is some overlap between romstage and bootblock.
LPC setup and BAR initialization is now done twice.
The rationale is that the romstage should not depend too
much on the bootblock, since it can reside in a RO fmap
region.
Enabling the console will be done in a followup patch.
Change-Id: I4d0ba29111a5df6f19033f5ce95adcc0d9adc1fd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The romstage default is to set stack guards at 0x2000 below end
of stack. The code is now overwrites some of the stack guards
so increase the stack size to a comfortable 0x2800.
Change-Id: I91f559383a987241b343e743d11291f2c100f7f5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This also changes the name to mainboard_pch_lpc_setup to better
reflect that it is an optional mainboard hook.
This adds an empty weakly linked default. The rationale behind this
change is that without an implementation of the hook some features
might not work but that the result is likely still able to boot, so it
can be made optional.
Change-Id: Ie8e6056b4c4aed3739d2d12b4224de36fe217189
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This also changes the name to mainboard_late_rcba_config to better
reflect what it does.
This adds an empty weakly linked default. The rationale behind this
change is that without an implementation of the hook some features
might not work but that the result is likely still able to boot, so it
can be made optional.
Change-Id: I1897d0f5ca7427d304a425f5256cd43c088ff936
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Id7babdc9b1d908fa90ebac098a019615fa00b973
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ie5c83befc8e595016c63729a19e7e71438c996b5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
This always builds the usb debug callback functions when implemented.
They get garbage collected if CONFIG_USBDEBUG is not set.
Change-Id: I33051df583645cd00d08e06774383763172d5822
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I425583377cba8d57acabfd59922f421d1fb5891f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The declarations in usb_debug.c needs to be guarded in order to not
conflict with other chipsets.
Change-Id: I84c3401b9419f2878c2cfdf81147fa854018f9ae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36878
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds an empty weakly linked default. The rationale behind this
change is that without the callback some features might not work
but that the result is likely still able to boot, so it can be made
optional.
Change-Id: I62c8010aa81fc45d208e9293feb2f45b45f34a82
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
RCBA32(V0CTL)= 0x80000001 already done inhere i945/early_init.c
Change-Id: Ia775f4e6158a217b48629d289845537e7ccf5e79
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
In order to always show the bootlogo very early in coreboot we need the
option to always enable the display when VBOOT is enabled.
To do this a config option is added to make sure this functionality can
be provided without interfering with systems that require the standard
VBOOT display handing.
BUG=N/A
TEST=tested on facebook fbg1701.
Change-Id: I3ffaac85d2082717bb9608d536f7cec66a583789
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Some special keys emit a prefix scan code 0xE0. We will ignore all
these except for the power button, F12 and cursor keys on drallion.
Media key mapping is set in depthcharge and will be sent to libpayload
keyboard driver. Whichever board requires this change will update its own
media key mapping.
BUG:b:139511038
TEST=boot in recovery mode, press F12 to go to diagnostic mode and power
button to confirm. Also in recovery mode left arrow, right arrow, up arrow,
down arrow changes the language on the firmware screen.
Change-Id: I1c11939d18391bebe53ca21cf33a096ba369cd56
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36654
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Leave more space for PreRAM memconsole especially for seeing complete
logs when doing DRAM full calibration (that outputs in 200+k to UART):
- Shrink Full-K mem space (the ELF blob today needs ~132K)
- Move PRERAM_CBFS_CACHE to L2C since it's no used after DRAM is up
- Shrink TIMESTAMP to 1k (all other non-MTK ARM SOCs use only 1k)
- Incease PRERAM_CBMEM_CONSOLE to 63k-4
- Reordered few sections to align at better locations
BUG=b:144542023
TEST=emerge-kukui coreboot chromeos-bootimage; boot and see logs
Change-Id: I8696fb01653c0a581cf62e687dc523cb6fed9a32
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Setting GPP_A10 to NC now that older boards are deprecated and this
GPIO is not in use anymore.
BUG=b:142056166
BRANCH=hatch
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: If8a249a3dcba90bb4ccb5e3f02595e680f789f93
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36869
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The eltan security items ended up in the chipset menu which is not
desired. Now the eltan security option (when enabled in mainboard) shows
up in the security menu.
BUG=N/A
TEST=build
Change-Id: I3b2aa3836e8d9a3242c6d1f3ba7b7821a5cfb9d3
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Change-Id: I4af62fdf4bfc34433d9f7dcf32acd1078b533a43
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These mainboard don't feature a SPI flash. The SPI init code
will timeout on probing for a SPI flash which takes a lot of time.
Not including all SPI drivers also lightens the uncompressed ramstage
of about 17K or 7K compressed.
Change-Id: Icc7bf62d56fc2ef38854402e658830b8d59c737f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36870
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On devices lacking SPI boot devices there is a hefty timeout
penalty on probing for flash chips and this code would not
be useful anyway.
Change-Id: I0bec11372ef54c1e1e611b81f7013932257f4ca6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36868
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating from commit id e561c63:
2019-10-02 17:03:58 +0530 - (lib: Fix coldboot race condition observed on emulators/simulators)
to commit id 215421c:
2019-11-11 16:40:34 -0800 - (lib: Remove date and time from init message)
This brings in 13 new commits and allows reproducible builds with
opensbi.
Change-Id: I0fb9e0921b017822defa8b56df5a0f3e014d7f33
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The verified_boot_check_cbfsfile() will now try to allocate a buffer from
bootmem if the item in the list has the VERIFIED_BOOT_COPY_BLOCK attribute
set. For large payloads this speeds up the hash operation.
BUG=N/A
TEST=build
Change-Id: Ifa0c93632c59d05ae6d32f8785009a3c3568abc5
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
vboot_possibly_executed previously provided some better
compile-time code elimination, before CB:32716 made
vboot_logic_executed capable of that directly.
BUG=b:124141368,
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: If5ca8f03c51e1ced20e1215b1cfdde54da3d001f
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36863
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The comment in the source referred to an earlier approach, so update
it to match current reality.
Change-Id: I9a23ec0a719fb623cfd465c397ef7ef16550b93c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
The old code stumbled when the whole first group of root ports
was disabled and also made the (sometimes wrong) assumption
that FSP would only hide function 0 if we explicitly told it
to disable it.
Change-Id: Ia6938ca6929c6d9d0293c4f0f0421e38bf53fb55
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36702
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most of the current implementations for FSP-based platforms
make (sometimes wrong) assumptions how FSP reorders root ports
and what is specified in the devicetree. We don't have to make
assumptions though, and can read the root-port number from the
PCIe link capapilities (LCAP) instead. This is also what we do
in ASL code for years already.
This new implementation acts solely on information read from
the PCI config space. In a first round, we scan all possible
DEVFNs and store which root port has that DEVFN now. Then, we
walk through the devicetree that still only knows devices that
were originally mentioned in `devicetree.cb`, update device
paths and unlink vanished devices.
To be most compatible, we work with the following constraints:
o Use only standard PCI config registers.
o Most notable, don't try to read the registers that
configure the function numbers. FSP has undocumented
ways to block access to non-standard registers.
o Don't make assumptions what function is assigned to
hidden devices.
The following assumptions were made, though:
o The absolute root-port numbering as documented in
datasheets matches what is read from LCAP.
o This numbering doesn't contain any gaps.
o Original root-port function numbers below a PCI
device start at function zero and also don't
contain any gaps.
Change-Id: Ib17d2b6fd34608603db3936d638bdf5acb46d717
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35985
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is some overlap between things done in bootblock
and romstage like setting BARs.
Change-Id: Icd1de34c3b5c0f36f2a5249116d1829ee3956f38
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36759
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic6ea158714998195614a63ee46a057f405de5616
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Console init in bootblock will be done in a separate CL.
Change-Id: Ia2405013f262d904aa82be323e928223dbb4296c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36795
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds callbacks for mainboard specific init.
Change-Id: Ib67bc492a7b7f02f9b57a52fd6730e16501b436e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36787
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds 3 mb romstage callbacks:
- void mb_lpc_setup(void) to be used to set up the superio
- void mb_get_spd_map(u8 spd_map[4]) to get I2C addresses of SPDs
- (optional)mb_pre_raminit_setup(int s3_resume) to set up mainboard
specific things before the raminit.
Change-Id: Ic3b838856b3076ed05eeeea7c0656c2078462272
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36758
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On mainboards without DPTF_TSRX_SENSOR_ID method DTRP is never called
Only add the DTRP method when at least one sensor is enabled.
BUG=N/A
TEST=build
Change-Id: I4fb26d5bbb7b334e759e7073b680f830f412467e
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36856
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add IFD and ME binary to generate complete SPI image.
BUG=N/A
TEST=Boot Embedded Linux 4.20 on Facebook FBG-1701
Change-Id: I9370bf9f2bba8887988bc6484524f6cf53bed8db
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34448
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Upgrade to blobs version with descriptor and Intel ME binary
BUG=N/A
TEST=booting Facebook FBG1701
Change-Id: I2143b94a81eebfb22d99833aaf1f3743983dd80c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34442
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The prepare() callback is no longer utilized in the code. Remove
the callback and support for it.
Change-Id: Ic438e5a80850a3df619dbbfdecb522a9dc2c1949
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
This patch renames pch_early_init() function as per review feedback
CB:36550
Change-Id: I9f638e738d1a910b688cc3e51795230b2e542f82
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
Change-Id: If932582d03bb2f6d3d14c9bce45cf2030f3b3c4e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Add a new Kukui follower 'kakadu'.
BUG=None
TEST=make # select kakadu
Change-Id: I9f25ce90285828c43435e45d9361ee7128d407fa
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36848
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add semtech SAR sensor.
BUG=b:143449140
BRANCH=octopus
TEST=Boot kernel with sx931x driver, i2cdetect show UU on slave address.
Change-Id: Icfb8acf1bac73973748aa7443c95147c60bad770
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36850
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIOs related to power sequnce are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:144327240
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Change-Id: I68b71425391eda1e92806fecdb9c8dcd54f0b95a
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36771
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The microcode is available in 3rdparty microcode now.
This ucode can be used.
BUG=N/A
TEST=build
Change-Id: I52a04c7dc97608f868ee0b415bbbb328937f18f7
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
The microcode is available in 3rdparty microcode now.
This ucode can be used.
BUG=N/A
TEST=build
Change-Id: I1d83a58e9051fa9402666f05e4f2c43e76026dfb
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36854
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the logo.bmp file from the verify list when FSP1_1_DISPLAY_LOGO
is not set.
BUG=N/A
TEST=build
Change-Id: I87eac0b3cbe9450d5623b5331d8de096f140b595
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36853
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Changed the order of the verify lists and updated the comments to
reflect the order of execution. This makes the list easier to understand
and maintain.
BUG=N/A
TEST=tested on fbg1701
Change-Id: Ia656fbf07e5d42bafd328eaba69b660e5a1e4f1a
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36817
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change from hardcoded "fallback/*" to using CONFIG_CBFS_PREFIX.
BUG=N/A
TEST=tested on fbg1701
Change-Id: Ie728d01ebb93edd88516e91528ecaaa3f139b7a9
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|