| Age | Commit message (Collapse) | Author |
|---|
|
Relying on the implicit defaults for these settings can cause issues in
the future. For example, commit 8cc4c5a1e76c0c8aee3a14618c15d38e3bd2bd61
(config.dell_optiplex_9010_sff: Specify board model) was done to prevent
a build failure when adding support for other Dell mainboards which make
the default board change.
Change-Id: Ie0da6254def8b38e9fb053fc7d530dfb46760861
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56079
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow hot plug devices to subscribe to IOMMU services. Currently the
IOMMU end range is limited to device B:0 D:1f F:6. This prevents the
devices on bus 1 and higher to subscribe to IOMMU services. As per AMD
IOMMU spec v3 section 5.2.2.1 all possible device IDs must be defined,
whether the device ID is actually populated or not. Device entries are
used to report ranges when hot-plug and SR-IOV devices are possible.
With this change the hot plug devices can now bind to IOMMU services
(as tested on kernel v5.4), and below errors are not seen in dmesg.
AMD-Vi: Event logged [IO_PAGE_FAULT device=04:00.3 domain=0x0000]
AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x0000]
AMD-Vi: Event logged [IO_PAGE_FAULT device=04:00.4 domain=0x0000]
TEST= Verify dGPU can enumerate on hotplug. No IO page fault errors seen.
The hot plug devices can successfully bind to IOMMU services in
kernel.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: I256c0f8032662674a4d75746de49c250e341c579
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55816
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: ritul guru <ritul.bits@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I755f2037bc9368e610eb97a2633aa66da7f626b0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56042
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TESTED on foxconn g41m.
Change-Id: I2d5d5dfbd76a84aa400e44b4bc2ac4f3b5b6f739
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56022
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I77516e3cd5f0d3b7442be660c005a65b00454343
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Tested on Intel Sandybridge x86_64 and x86_32.
Change-Id: I152483d24af0512c0ee4fbbe8931b7312e487ac6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add defconfig to build test x86_64 code on Sandy Bridge.
Change-Id: I2c18af8bfa87636c68741e4759059276c287d052
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrik Tesarik <depate@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There will be more variants of this mainboard so prepare the scheme for
Kconfig to handle the variants properly.
Change-Id: If1cf418836d77a45955ee55d30ba670db8ff2533
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add a new mainboard called mc_ehl which is based on Intel's
'elkhartlake_crb'. This commit simply copies the mainboard directory and
adjusts the naming to match the new board's name. Follow-up commits will
introduce the needed changes for the new mainboard.
Change-Id: Ia7c0616098046d975aa698910ac81f435d7882cb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
To ease finding some log messages, reflow their strings to use one line.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I5284429ca6d07debf2d6c4fdbffa286140fb7694
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
camera ACPI
This change updates device tree to enable SSDT generation for
world facing camera and user facing camera for ADLRVP.
Also reverts DSDT changes related to both camera.
TEST=Build and Boot aldrvp check i2c enumeration and output of media-ctl
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I39f82dc9eb91496d80479ae3f59ca5e03402a599
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
ACPI
This change updates device tree to enable SSDT generation for
world facing camera and user facing camera for ADLRVP.
Also reverts DSDT changes related to both camera.
TEST=Build and Boot aldrvp check i2c enumeration and output of media-ctl
Compared SSDT with this patch against DSDT without this patch, they are same
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I08834bbcf80dc46737de07f69a2402ed6bf93d4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Redirect stdout and stderr from grep to check for unknown timestamps,
when no timestamps are stored, which is already logged earlier.
Failed to run "/root/coreboot/util/cbmem/cbmem -t", ignoring
Getting remote dmesg
grep: /tmp/coreboot_board_status.dXmbUIBP/emulation/qemu-i440fx/4.14-876-gdb28040ee1/2021-07-02T23_14_33Z/coreboot_timestamps.txt: No such file or directory
Change-Id: Ib5400d4bd17e957b4cc1bf75bbd332d60ad226f5
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The caller is already passing the address to the required LTE reset and
enable GPIO. During memcpy, the address to that pointer is used which
will lead to copying undefined data. Fix the pointer/address used in
memcpy.
BUG=None
BRANCH=dedede
TEST=Build Kracko, Drawcia and Metaknight mainboards which use this
function.
Change-Id: I79d6d9af03acd59ab5e1cd7df97bf451011dfeaa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Found-by: Coverity CID 1458053, 1458054.
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56046
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
cr50_enable_update takes a non-trivial amount of time.
TEST=Boot guybrush and dump timestamps
553:started TPM enable update 3,615,156 (444)
554:finished TPM enable update 3,632,810 (17,654)
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I522d0638a4a6ae9624965e49b47bca8743c3206c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Currently, four instead of three = are used in one log message.
Done reading resources.
==== Resource allocator: DOMAIN: 0000 - Pass 1 (gathering requirements) ===
=== Resource allocator: DOMAIN: 0000 - Pass 2 (allocating resources) ===
As the ending mark is `===` change it to `===` in the beginning.
Done reading resources.
=== Resource allocator: DOMAIN: 0000 - Pass 1 (gathering requirements) ===
=== Resource allocator: DOMAIN: 0000 - Pass 2 (allocating resources) ===
Change-Id: I40c3876e1f895b7f9771479234c9529cca2b97ba
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56045
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Do the usual int conversions.
TESTED: BUILD_TIMELESS=1 produces identical image on foxconn/g41m.
Change-Id: Idebfe4669854b307bee653df6d93e46ae3f39dec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56020
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This removes the need for type conversions all over the place.
Change-Id: I633a453aff17f1cbbe06b60e3efb67661733d06c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56029
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Do the usual type conversions
TESTED: Same image with BUILD_TIMELESS=1
Change-Id: Id44eeb7660d0b521a326a5b981c04c16cf0a6f84
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56019
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use proper car symbols.
Change-Id: I169fd6020e5b81da66dbe4fe83ba446eedc882e9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56018
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the optimized FIVR configuration for adlrvp cutomized
based on the pnp measurements to achieve the better power savings in
sleep states.
* Enable the external V1p05, Vnn, VnnSx rails in S0i1, S0i2, S0i3, S3,
S4, S5 states.
* Update the supported voltage states.
* Set the ICC max to 500mA for v1p05 and vnn.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I83e6910502d5cf9d4c26fa581272f59ac483ae19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch adds the supports to update the optimal FIVR
configurations for external voltage rails via devicetree.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Icf6c74bda5a167abf63938ebed6affc6b31c76f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55702
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
brya0 is a reference and development platform, therefore it would be
helpful to have Crashlog enabled.
Change-Id: I936e73e808e0a05e8b7822cddbb5ee3fa7dee13e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The brya EC supports S0ix hang detection, but it was not enabled in
coreboot as well, masking that event out of S0ix, therefore add it in to
the EC S0ix wake mask.
TEST=After EC prints "Warning: Detected sleep hang! Waking host up!",
the host actually wakes up
Change-Id: I2c699114abcd9a045a41858c731e4b6fe99d3000
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Cret doesn't support SDCard. Disable SDCard contorller for Cret.
BUG=b:191232222
TEST=Build and boot to check lspci
Cq-Depend: chromium:2993724
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I889f0545883aa75813dd91dc3e6a4dcfc246687f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Correct Bus and Device for THC0 and THC1
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I41858ea156c8258ea0e7be9e2f67fb0e24144c80
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Allow to use the 2nd COM port of the AST2400 which can be also used via
IPMI/serial-over-lan.
Change-Id: I6f9c85b1f5428d3c3acf7a2f20296134c4611b1e
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The -a flag was already implemented, it just wasn't exposed for the
add-payload command.
Setting the alignment of the payload will enable using the SPI DMA
controller to read the payload on AMD devices.
BUG=b:179699789
TEST=cbfstool foo.bin add-payload -a 64 ...
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9f4aea5f0cbeaa8e761212041099b37f4718ac39
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=none
TEST=Boot with CONSOLE_LOGLEVEL_3 and no longer see the message printed.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0bdb92f547ceb8be624521211f4a3b94a91dae22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This message is not an error, but just informational.
BUG=none
TEST=Boot with CONSOLE_LOGLEVEL_3 and no longer see it printed
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ifb64edbe029cafa82aec99aa50de47f51cd50dce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We are currently reading the uCode for each CPU. This is unnecessary
since the uCode never changes.
BUG=b:177909625
TEST=Boot guybrush and see "microcode: being updated to patch id" for
each CPU. I no longer see CBFS access for each CPU. This drops device
initialization time by 32 ms.
Also boot Ezkinil and verify microcode was also updated.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I98b9d4ce8290a1f08063176809e903e671663208
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Start using the custom boot device.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4ae7272677f563e8827ba154fe5177c8c01155c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is a copy of mmap_boot.c and mem_rdev_ro_ops. I split it up so it
was easier to review.
The next patches will add support for the SPI DMA controller. This will
provide a minor speed up vs using mmap reads. It will also provide the
facilities to perform asynchronous SPI loading.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id26e2a69601d0f31e256d0010008904a447c8e21
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In order to disable X86_TOP4G_BOOTMEDIA_MAP it requires the definition
to be overridden. This makes it a little less ergonomic to use. Instead
introduce the inverse option that can be selected. I chose to leave
X86_TOP4G_BOOTMEDIA_MAP since it keeps the Makefiles simple.
BUG=b:179699789
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I65bbc118bde88687a7d7749c87acf1cbdc56a269
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
On x86_64, the default heap size is too small when using 32 CPUs.
Change-Id: Ib4f770a7a54d975d213b2456cc7d1ed9151cb6f9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Introduce `USE_EXP_X86_64_SUPPORT` in `src/arch/x86/Kconfig` and guard
it with `HAVE_EXP_X86_64_SUPPORT`. Replace the per-CPU implementations
of the same functionality with the newly-added Kconfig options. Update
documentation and the config file for QEMU accordingly.
Change-Id: I550216fd2a8323342d6b605306b0b95ffd5dcd1c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Introduce the `ARCH_ALL_STAGES_X86` Kconfig symbol to automatically
select the per-stage arch options. Subsequent commits will leverage
this to allow choosing between 32-bit and 64-bit coreboot where all
stages are x86. AMD Picasso and AMD Cezanne are the only exceptions
to this rule: they disable `ARCH_ALL_STAGES_X86` and explicitly set
the per-stage arch options accordingly.
Change-Id: Ia2ddbae8c0dfb5301352d725032f6ebd370428c9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add G2 touchscreen support for magma.
BUG=b:189852808
TEST=Build and verify that touchscreen works.
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I3e032bff7f3e97f54f3e544035e862058ea0dbfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
BUG=b:191362590
TEST=on brya, cbmem -t:
942:before sending EOP to ME 2,628,446 (5,879)
943:after sending EOP to ME 2,631,177 (2,730)
Change-Id: I0376610c5cbae7df1bf1a927b3bc99b1022de4cb
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add SPD support to eldrid for DDR4 memory part MT40A512M16TB-062E:R.
Eldrid should use DRAM_ID strap ID 0 (0000) on SKUs populated
with MT40A512M16TB-062E:R DDR4 memory parts.
BUG=b:192380070
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
successfully.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I4d07727c9c41bf494fbef373abce0ac1fc65c316
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55983
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need to repeat "import" for each module in GoLang. Use
this keyword only once in each file for code cleanliness.
Change-Id: Ibb24fafd409b31b174946a39ca1f810d59b87e76
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55985
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to detect USB Type C device port as Super Speed, we need to set
corresponding bit in UPD UsbTcPortEn. This patch will use device path
to determine which port should be enabled.
BUG=b:184324979
Test=Boot board, USB Type C must be functional and operate at Super Speed.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I7da63f21d51889a888699540f780cb26b480c26d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Since bootmem is not available in romstage, calls to bootmem APIs need
to be compile-time eliminated in order to avoid linker error:
undefined reference to `bootmem_region_targets_type
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -B
cherry-picked on top of CB:49392 and verified successful
compilation.
Change-Id: I8dfa2f2079a9a2859114c53c22bf7ef466ac2ad9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55865
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently the flow for opregion init is as below:
1. Allocate memory for opregion first (cbmem_add(opregion))
2. Check if VBT size > 6 KiB (this requires extended VBT support)
3. In case of extended VBT requirement, we allocate another chunk
of memory which is equal to size of VBT (cbmem_add(extended_vbt))
4. Pass physical address pointer to OS via RVDA
We can optimize the above flow to allocate single chunk of memory by
checking VBT size in earlier step. The new optimized flow for opregion
init is as below:
1. Check if VBT size > 6 KiB (this requires extended VBT support)
2. In case of extended VBT requirement, total memory to be allocated
is calculated as sizeof(opregion) + sizeof (extended_vbt)
In case where VBT size is < 6 KiB, total memory requirement would
be equal to sizeof(opregion)
3. Based on above calculation, allocate single chunk of memory based on
total size.
This will also be helpful for the case of virtualization where guest
users don't have access to physical address and when it needs relative
address of VBT compared to absolute address.
In case of opregion 2.1 spec, we need to pass relative address of
VBT from opregion base in RVDA. This optimization will help in meeting
this requirement since relative address of extended VBT is easy to get.
This change will ensure that it meets opregion specification
requirement and will be compatible with future versions as well.
BUG=b:190019970
BRANCH=None
TEST=check the address of extended VBT region and address is coming
correctly.
Change-Id: Ic0e255df63145409096b0b9312c6c51c05f49931
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The dereferced parameter is never updated so passing a copy would work
too.
Change-Id: Ie36f64f55d4fc7034780116c28aaed65aa304d5e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55792
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Scout-specific changes to puff reference following bring-up
- copy baseline changes from genesis
- update GPIOs
- update PCIe ports for TPUs
- remove LSPCON
- enable eMMC
- disable touch I2C
- enable uart
BUG=b:187078663
TEST=boot scout
BRANCH=none
Signed-off-by: Jeff Chase <jnchase@google.com>
Change-Id: Ic3cb9cf515ab7a4a0ebbee249644dd3f133d8735
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
P-sensor is swap by the latest schematic. Thus, swap the IRQ for correct
P-sensor.
BUG=b:192331122,b:181555900
TEST=check P-sensor driver can be probed without error.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3ccb31c1925e476e2ebb34b2439a491759472405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch enables the energy efficiency turbo mode.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I2d76c948bdc9c208f5728e305b3034fcede6f4bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55705
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The same pattern appears on all `xdci_can_enable()` call sites. Move the
logic inside the function and take the xDCI devfn as parameter.
Change-Id: I94c24c10c7fc7c5b4938cffca17bdfb853c7bd59
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This adds OEM variables feature under DPTF as per BWG doc #541817. Using
this, platform vendors can expose an array of OEM-specific values as OEM
variables to be used in determining DPTF policy. These are obtained via
the ODVP method, and then simply exposed under sysfs. In addition, these
gets updated when a notification is received or when the DPTF policy is
changed by userspace.
BRANCH=None
BUG=b:187253038
TEST=Built and tested on dedede board
Change-Id: Iaf3cf7b40e9a441b41d0c659d76895a58669c2fb
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Drop extern declarations from functions.
Declare resource arguments as const.
Change-Id: I7684cc7813bad805c39a762892636818279ac134
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55475
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This fixes building with libgfxinit in x86_64 mode, which can
generates unsupported R_X86_64_32S relocations without -mcmodel=large.
Change-Id: If5162fae475f3e70c856d9664a8cfc6a89d82283
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55549
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Do not call `pci_assign_irqs` with a NULL device pointer.
Change-Id: Ide9ae38dedd881ed673ba1838a1e29529b306937
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tidy up the code that programs the PAM (Programmable Attribute Map)
registers. Introduce the `D0F0_PAM` macro and use it to replace the
magic `0x59` and `0x5a` values in the code. Adjust the range of the
for-loop to work with the `D0F0_PAM` macro, and properly indent the
loop's body.
Change-Id: I9036425d726ffb69737ea6ed36c7a8f61d9d040a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Mainboard information can be found in the included documentation.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Idb696193e5a67c42adf45e54d455d2dff7681ca7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Return the HSI version read from BMC in smbios_mainboard_version.
Change-Id: If907d598c9e05d35f8898d294678f61d075f935a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create the cappy2 variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192035460
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CAPPY2
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I772801152b9ca9c2c6afe76a353cb2b62d6210ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
upgrade
This changes updates mainboard properties by adding DFP number and
power_gpio for each DFP.
Reference CB:55348
BUG=b:191897776
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I63c912980530e5c9f341bdbab18c07685fd77abf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add LTE modem to devicetree.
Configure GPIO control for LTE modem by fw_config.
Update LTE USB port configuration at run-time after probing FW_CONFIG.
By default the concerned USB port takes the Type-A port configuration.
BUG=b:186393848
TEST=Build image and check with command modem status
Change-Id: I20450ae37e5047dba67211316515994bd2a09600
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update LTE USB port configuration at run-time after probing FW_CONFIG.
By default the concerned USB port takes the Type-A port configuration.
BUG=b:178092096
BRANCH=dedede
TEST=Build and boot to OS to check LTE by modem status
Change-Id: If12cc29ddda6d5c32c0bda840a3680e7bf932f89
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54671
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `irq` variable has the same value as `pIntAtoD[line - 1]`.
Change-Id: Iabf760adbc3014b32cfe6f908dc04c38b71bd980
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
By enabling the flag alderlake platform will use hardware sha
instruction instead of software implementation for sha256.
This will speed up firmware verification especially on low-performance
device.
Change-Id: Ie8ab02360fdceafab257e9a301e6a89d3a22c3ae
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add Kconfig option for VBOOT_X86_SHA256_ACCELERATION, which will
use x86-sha extension for SHA256 instead of software implementation.
TEST=Able to call vb2ex_hwcrypto_digest_init() and perform SHA
using HW crypto engine.
Change-Id: Idc8be8711c69f4ebc489cd37cc3749c0b257c610
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Updating from commit id b38e3a63:
cros_ec: Use boot mode to check if EC can be trusted
to commit id ccc56f4:
vboot: add x86 SHA256 ext support
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I4e170e84a12646386d3fd84ae97add6c19f23809
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Now that the refactoring is complete, the unions for the table header
are no longer needed. Therefore, drop them.
Change-Id: I4e170e84a12646386d3fd84ae973dd6c18f25809
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Replace uses of `smbios_type0` with `smbios_header` for correctness.
Change-Id: I2479984f5322f0fb474ff1707c1dd1f5885f30e9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Introduce the `smbios_full_table_len` function to consolidate table
length calculation. The case where the length of a table equals the
length of the structure happens when a table has no strings.
Change-Id: Ibc60075e82eb66b5d0b7132b16da000b153413f9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Change-Id: I949da86605e76b186ef2fdbfbc112b71544b694a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Factor out some boilerplate code into a helper `smbios_carve_table`
function, which zeroes out the table memory and fills in the header
fields common to all tables.
Change-Id: Iece2f64f9151d3c79813f6264dfb3a92d98c2035
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
All SMBIOS `type X` tables start with the same 4-byte header. Add a
struct definition for it, and use it where applicable. The union is
temporary and allows doing the necessary changes in smaller commits.
Change-Id: Ibd9a80010f83fd7ebefc014b981d430f5723808c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The initial value of `len` is never used. Declare and initialise all
local variables in a single statement to avoid this problem.
Change-Id: Ieb96758f4cd19d9d3f8fdc543e8ca17db06a2123
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Where applicable, use the size of the associated variable.
Change-Id: Ibbac2a82893232a6f87182a6a965b84a599d633e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Reduce the scope or remove some `len` variables. This is done to ease
replacing `sizeof` on struct types in a follow-up commit, by ensuring
that all to-be-replaced appearances follow the variable declarations.
Change-Id: Ied38fcaf87ef5b1e4f93076b4ba2898ad1f98a72
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Where applicable, use the size of the associated variable.
Change-Id: Icf4f1c8fe9f54c44b041a65eb46d6ec9f9fd6367
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I11daebbfc44959f1e498ddac2ee7633e31a1a7d5
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
This is done to ensure the CSE will not execute any pre-boot commands
after it receives this command. Verified EOP and error recovery sequence
from Intel doc#619830.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I36fe448ff279ba054ad5e79e71c995dc915db21e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55633
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is done to ensure the CSE will not execute any pre-boot commands
after it receives this command. Verified EOP and error recovery sequence
from Intel doc#612229
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iae6b2eac11c065749e57c5337d81ed20044fc903
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is done to ensure the CSE will not execute any pre-boot commands
after it receives this command. Verified EOP and error recovery sequence
from Intel doc#627331.
TEST=on brya, autotest firmware_CheckEOPState confirms ME is in
post-boot state
Change-Id: Iee8c29f81d5d04852ae3f16dc8a9ff0fa59f056a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds functionality to attempt to allow booting in a secure
configuration (albeit with potentially reduced functionality) when the
CSE EOP message fails in any way. These steps come from the CSME BWG
(13.5, 15.0, 16.), and tell the CSE to disable the MEI bus, which
disables further communication from the host. This is followed by
requesting the PMC to disable the MEI devices. If these steps are
successful, then the boot firmware can continue to boot to the
OS. Otherwise, die() is called, prefering not to boot over leaving the
insecure MEI bus available.
BUG=b:191362590
TEST=Set FSP UPD to disable sending EOP; called this function from a
BS_PAYLOAD_LOAD, ON_ENTRY entry; observed that with just
cse_mei_bus_disable() called, Linux can no longer communicate over MEI:
[ 16.198759] mei_me 0000:00:16.0: wait hw ready failed
[ 16.204488] mei_me 0000:00:16.0: hw_start failed ret = -62
[ 16.210804] mei_me 0000:00:16.0: H_RST is set = 0x80000031
[ 18.245909] mei_me 0000:00:16.0: wait hw ready failed
[ 18.251601] mei_me 0000:00:16.0: hw_start failed ret = -62
[ 18.257785] mei_me 0000:00:16.0: reset: reached maximal consecutive..
[ 18.267622] mei_me 0000:00:16.0: reset failed ret = -19
[ 18.273580] mei_me 0000:00:16.0: link layer initialization failed.
[ 18.280521] mei_me 0000:00:16.0: init hw failure.
[ 18.285880] mei_me 0000:00:16.0: initialization failed.
Calling both error recovery functions causes all of the slot 16 devices
to fail to enumerate in the OS
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I06abf36a9d9d8a5f2afba6002dd5695dd2107db1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55675
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
init overridetree.cb based on the schematic carbine_adl-p_proto_20210618_proto final.pdf
BUG=b:191213263
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I3f6875ef438b147436605629445d346a56896a87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
set GPP_C3 and GPP_C4 as NC since LAN function removal.
BUG=b:190643562
Change-Id: I21214d0a2904ba4347fbbbc74237aca6db22c345
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55933
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable PCH GBE with following changes:
1. Configure PCH GBE related FSP UPD flags
2. Use EHL own GBE ACPI instead of common code version due to
different B:D.F from the usual GBE
3. Add kconfig PMC_EPOC to use the PMC XTAL read function
Due to EHL GBE comes with time sensitive networking (TSN)
capability integrated, EHL FSP is using 'PchTsn' instead of the
usual 'PchLan' naming convention across the board.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I6b0108e892064e804693a34e360034ae7dbee68f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
1. Remove 'PCH_EPOC_XTAL_FREQ(__epoc)' macro since it only be used
in 1 place.
2. Transform macro into more readable C code.
3. Add additional case check to make sure the returned value is
defined in the 'pch_pmc_xtal' enum.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: If57a99bf8e837a6eb8f225297399b1f5363cfa85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Move PMC EPOC related code to intel/common/block because it is
generic for most Intel platforms and ADL, TGL & EHL use it.
Add a kconfig 'PMC_EPOC' to guard this common EPOC code.
The PMC EPOC register indicates which external crystal oscillator is
connected to the PCH. This frequency is important for determining the
IP clock of internal PCH devices.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ib5fd3c4a648964678ee40ed0f60ca10fe7953f56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
google_chromeec_get_event returns 0 for no event. Return
EC_HOST_EVENT_NONE=0 to improve readability.
BUG=b:184074997
TEST=Build and boot guybrush without error
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: Ic08ed9ccdd7c0023d0fe8b641fcf60dca495a242
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change syncs the coreboot version of google ec_commands.h with the
ec_commands.h from the google ec repository. This is a straight copy
except for the the copyright header.
BUG=b:184074997
TEST=Build and boot guybrush
BRANCH=None
Change-Id: I095c3316d720328cb7b8dd1b72ffc108208b14bd
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change adds fine-tuned USB2 PHY parameters for storo.
BUG=191089827
TEST=Built and verified USB2 eye diagram test result
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I38dd8ad59b32f635e641765e0a1bd13651180d23
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:190027970,b:178175837
BRANCH=dedede
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I7084f9b7be2b66adda2d9d5a83ce5dd9c31d01b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
To generalise the choice of 32-bit or 64-bit coreboot on x86 hardware,
have platforms select `ARCH_X86` directly instead of through per-stage
Kconfig options, effectively reversing the dependency order.
Change-Id: If15436817ba664398055e9efc6c7c656de3bf3e4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
With two versions of *speed_mhz_to_reported_mts() we need to call the
correct one based on the reported memory type.
BUG=b:184124605
TEST="dmidecode --type 17" in OS on Guybrush
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Change-Id: I92e834097546e3ef7130830444a80f818bdea3d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55852
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This guard is nested inside an identical guard already.
Change-Id: I2b315ee6620865429097041035ad493ddcc51884
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Set GPP_B3 to APIC mode to avoid PCI IRQ conflict.
BUG=b:181555900
TEST=check dmesg there are no IRQ request errors like below.
genirq: Flags mismatch irq 27. 00002008 (sx932x_event) vs. 00000080 (idma64.1)
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idf88fae9e244858445c45e66e26715cebe0c93ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: If5e72b36242e1aff7ce2609ea6bdbaea53683bd9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Since GPIO IO-APIC IRQs are fixed in hardware (RO registers), this patch
allows tigerlake boards to dynamically assign PCI IRQs. This means not
relying on FSP defaults, which eliminates the problem of PCI IRQs
interfering with GPIO IRQs routed to the same IRQ, when both have
selected IO-APIC routing.
BUG=b:171580862
TEST=on delbin, grep 'IO-APIC' /proc/interrupts (compressed to fit)
0: 6 0 0 0 IO-APIC 2-edge timer
1: 0 35 0 0 IO-APIC 1-edge i8042
8: 0 0 0 0 IO-APIC 8-edge rtc0
9: 0 601 0 0 IO-APIC 9-fasteoi acpi
14: 1 0 0 0 IO-APIC 14-fasteoi INT34C5:00
20: 0 0 0 516 IO-APIC 20-fasteoi idma64.6, ttyS0
28: 0 395 0 0 IO-APIC 28-fasteoi idma64.0, i2c_design
29: 0 0 1654 0 IO-APIC 29-fasteoi idma64.1, i2c_design
30: 0 0 0 0 IO-APIC 30-fasteoi idma64.2, i2c_design
31: 0 0 0 0 IO-APIC 31-fasteoi idma64.3, i2c_design
32: 0 0 0 0 IO-APIC 32-fasteoi idma64.4, i2c_design
33: 0 0 14469 0 IO-APIC 33-fasteoi idma64.5, i2c_design
35: 0 18494 0 0 IO-APIC 35-edge cr50_spi
36: 95705 0 0 0 IO-APIC 36-fasteoi idma64.7, pxa2xx-spi
37: 0 0 1978 0 IO-APIC 37-fasteoi idma64.8, pxa2xx-spi
51: 1865 0 0 0 IO-APIC 51-fasteoi ELAN9008:00
59: 0 0 422 0 IO-APIC 59-fasteoi ELAN0000:00
116: 0 0 0 23 IO-APIC 116-fasteoi chromeos-ec
abbreviated _PRT dump:
Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table
If (PICM)
Package () {0x0002FFFF, 0x00, 0x00, 0x10},
Package () {0x0004FFFF, 0x00, 0x00, 0x11},
Package () {0x0005FFFF, 0x00, 0x00, 0x12},
Package () {0x0006FFFF, 0x00, 0x00, 0x13},
Package () {0x0007FFFF, 0x00, 0x00, 0x14},
Package () {0x0007FFFF, 0x01, 0x00, 0x15},
Package () {0x0007FFFF, 0x02, 0x00, 0x16},
Package () {0x0007FFFF, 0x03, 0x00, 0x17},
Package () {0x000DFFFF, 0x00, 0x00, 0x10},
Package () {0x000DFFFF, 0x01, 0x00, 0x11},
Package () {0x000DFFFF, 0x02, 0x00, 0x12},
Package () {0x0010FFFF, 0x00, 0x00, 0x13},
Package () {0x0010FFFF, 0x01, 0x00, 0x14},
Package () {0x0011FFFF, 0x00, 0x00, 0x18},
Package () {0x0012FFFF, 0x00, 0x00, 0x19},
Package () {0x0012FFFF, 0x01, 0x00, 0x1A},
Package () {0x0013FFFF, 0x00, 0x00, 0x1B},
Package () {0x0014FFFF, 0x00, 0x00, 0x15},
Package () {0x0015FFFF, 0x00, 0x00, 0x1C},
Package () {0x0015FFFF, 0x01, 0x00, 0x1D},
Package () {0x0015FFFF, 0x02, 0x00, 0x1E},
Package () {0x0015FFFF, 0x03, 0x00, 0x1F},
Package () {0x0016FFFF, 0x00, 0x00, 0x16},
Package () {0x0016FFFF, 0x01, 0x00, 0x17},
Package () {0x0016FFFF, 0x02, 0x00, 0x10},
Package () {0x0016FFFF, 0x03, 0x00, 0x11},
Package () {0x0017FFFF, 0x00, 0x00, 0x12},
Package () {0x0019FFFF, 0x00, 0x00, 0x20},
Package () {0x0019FFFF, 0x01, 0x00, 0x21},
Package () {0x0019FFFF, 0x02, 0x00, 0x22},
Package () {0x001CFFFF, 0x00, 0x00, 0x10},
Package () {0x001CFFFF, 0x01, 0x00, 0x11},
Package () {0x001CFFFF, 0x02, 0x00, 0x12},
Package () {0x001CFFFF, 0x03, 0x00, 0x13},
Package () {0x001DFFFF, 0x00, 0x00, 0x10},
Package () {0x001DFFFF, 0x01, 0x00, 0x11},
Package () {0x001DFFFF, 0x02, 0x00, 0x12},
Package () {0x001DFFFF, 0x03, 0x00, 0x13},
Package () {0x001EFFFF, 0x00, 0x00, 0x14},
Package () {0x001EFFFF, 0x01, 0x00, 0x15},
Package () {0x001EFFFF, 0x02, 0x00, 0x24},
Package () {0x001EFFFF, 0x03, 0x00, 0x25},
Package () {0x001FFFFF, 0x01, 0x00, 0x17},
Package () {0x001FFFFF, 0x02, 0x00, 0x14},
Package () {0x001FFFFF, 0x03, 0x00, 0x15},
Package () {0x001FFFFF, 0x00, 0x00, 0x16},
Else
Package () {0x0002FFFF, 0x00, 0x00, 0x0B},
Package () {0x0004FFFF, 0x00, 0x00, 0x0A},
Package () {0x0005FFFF, 0x00, 0x00, 0x0B},
Package () {0x0006FFFF, 0x00, 0x00, 0x0B},
Package () {0x0007FFFF, 0x00, 0x00, 0x0B},
Package () {0x0007FFFF, 0x01, 0x00, 0x0B},
Package () {0x0007FFFF, 0x02, 0x00, 0x0B},
Package () {0x0007FFFF, 0x03, 0x00, 0x0B},
Package () {0x000DFFFF, 0x00, 0x00, 0x0B},
Package () {0x000DFFFF, 0x01, 0x00, 0x0A},
Package () {0x000DFFFF, 0x02, 0x00, 0x0B},
Package () {0x0010FFFF, 0x00, 0x00, 0x0B},
Package () {0x0010FFFF, 0x01, 0x00, 0x0B},
Package () {0x0014FFFF, 0x00, 0x00, 0x0B},
Package () {0x0016FFFF, 0x00, 0x00, 0x0B},
Package () {0x0016FFFF, 0x01, 0x00, 0x0B},
Package () {0x0016FFFF, 0x02, 0x00, 0x0B},
Package () {0x0016FFFF, 0x03, 0x00, 0x0A},
Package () {0x0017FFFF, 0x00, 0x00, 0x0B},
Package () {0x001CFFFF, 0x00, 0x00, 0x0B},
Package () {0x001CFFFF, 0x01, 0x00, 0x0A},
Package () {0x001CFFFF, 0x02, 0x00, 0x0B},
Package () {0x001CFFFF, 0x03, 0x00, 0x0B},
Package () {0x001DFFFF, 0x00, 0x00, 0x0B},
Package () {0x001DFFFF, 0x01, 0x00, 0x0A},
Package () {0x001DFFFF, 0x02, 0x00, 0x0B},
Package () {0x001DFFFF, 0x03, 0x00, 0x0B},
Package () {0x001EFFFF, 0x00, 0x00, 0x0B},
Package () {0x001EFFFF, 0x01, 0x00, 0x0B},
Package () {0x001FFFFF, 0x01, 0x00, 0x0B},
Package () {0x001FFFFF, 0x02, 0x00, 0x0B},
Package () {0x001FFFFF, 0x03, 0x00, 0x0B},
Package () {0x001FFFFF, 0x00, 0x00, 0x0B},
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ieb241f2b91af52a7e2d0efe997d35732882ac463
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49409
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since GPIO IO-APIC IRQs are fixed in hardware (RO registers), this patch
allows ADL boards to dynamically assign PCI IRQs. This means not relying
on FSP defaults, which eliminates the problem of PCI IRQs interfering
with GPIO IRQs routed to the same IRQ, when both have selected IO-APIC
routing.
BUG=b:176858827
TEST=brya0, grep 'IO-APIC' /proc/interrupts (compressed to fit)
0: 36 0 0 0 0 0 0 0 IO-APIC 2-edge time
1: 0 0 9 0 0 0 0 0 IO-APIC 1-edge i804
8: 0 0 0 0 0 0 0 0 IO-APIC 8-edge rtc0
9: 0 21705 0 0 0 0 0 0 IO-APIC 9-fasteoi acpi
14: 0 0 0 0 0 0 0 0 IO-APIC 14-fasteoi INTC
18: 0 0 0 0 0 0 0 0 IO-APIC 18-fasteoi inte
20: 0 0 0 0 0 0 0 394 IO-APIC 20-fasteoi idma
23: 2280 0 0 0 0 0 0 0 IO-APIC 23-fasteoi idma
26: 0 0 26 0 0 0 0 0 IO-APIC 26-fasteoi idma
27: 0 0 0 6 0 0 0 0 IO-APIC 27-fasteoi idma
28: 0 0 0 0 0 0 0 0 IO-APIC 28-fasteoi idma
29: 0 0 0 0 25784 0 0 0 IO-APIC 29-fasteoi idma
30: 0 0 0 0 0 0 0 0 IO-APIC 30-fasteoi idma
31: 0 0 0 0 0 0 226 0 IO-APIC 31-fasteoi idma
77: 0 0 0 0 0 2604 0 0 IO-APIC 77-edge cr50
100: 0 0 0 0 0 0 0 0 IO-APIC 100-fasteoi ELAN
103: 0 0 0 0 0 0 0 0 IO-APIC 103-fasteoi chro
abbreviated _PRT dump:
If (PICM)
Package (){0x0002FFFF, 0, 0, 0x10},
Package (){0x0004FFFF, 0, 0, 0x11},
Package (){0x0005FFFF, 0, 0, 0x12},
Package (){0x0006FFFF, 0, 0, 0x13},
Package (){0x0006FFFF, 1, 0, 0x14},
Package (){0x0007FFFF, 0, 0, 0x15},
Package (){0x0007FFFF, 1, 0, 0x16},
Package (){0x0007FFFF, 2, 0, 0x17},
Package (){0x0007FFFF, 3, 0, 0x10},
Package (){0x000DFFFF, 0, 0, 0x11},
Package (){0x0012FFFF, 0, 0, 0x18},
Package (){0x0012FFFF, 1, 0, 0x19},
Package (){0x0014FFFF, 0, 0, 0x12},
Package (){0x0014FFFF, 1, 0, 0x13},
Package (){0x0015FFFF, 0, 0, 0x1A},
Package (){0x0015FFFF, 1, 0, 0x1B},
Package (){0x0015FFFF, 2, 0, 0x1C},
Package (){0x0015FFFF, 3, 0, 0x1D},
Package (){0x0016FFFF, 0, 0, 0x14},
Package (){0x0016FFFF, 1, 0, 0x15},
Package (){0x0016FFFF, 2, 0, 0x16},
Package (){0x0016FFFF, 3, 0, 0x17},
Package (){0x0017FFFF, 0, 0, 0x10},
Package (){0x0019FFFF, 0, 0, 0x1E},
Package (){0x0019FFFF, 1, 0, 0x1F},
Package (){0x0019FFFF, 2, 0, 0x20},
Package (){0x001CFFFF, 0, 0, 0x10},
Package (){0x001CFFFF, 1, 0, 0x11},
Package (){0x001CFFFF, 2, 0, 0x12},
Package (){0x001CFFFF, 3, 0, 0x13},
Package (){0x001DFFFF, 0, 0, 0x10},
Package (){0x001DFFFF, 1, 0, 0x11},
Package (){0x001DFFFF, 2, 0, 0x12},
Package (){0x001DFFFF, 3, 0, 0x13},
Package (){0x001EFFFF, 0, 0, 0x14},
Package (){0x001EFFFF, 1, 0, 0x15},
Package (){0x001EFFFF, 2, 0, 0x16},
Package (){0x001EFFFF, 3, 0, 0x17},
Package (){0x001FFFFF, 1, 0, 0x15},
Package (){0x001FFFFF, 2, 0, 0x16},
Package (){0x001FFFFF, 3, 0, 0x17},
Package (){0x001FFFFF, 0, 0, 0x14},
Else
Package (){0x0002FFFF, 0, 0, 0x0B},
Package (){0x0004FFFF, 0, 0, 0x0A},
Package (){0x0005FFFF, 0, 0, 0x0B},
Package (){0x0006FFFF, 0, 0, 0x0B},
Package (){0x0006FFFF, 1, 0, 0x0B},
Package (){0x0007FFFF, 0, 0, 0x0B},
Package (){0x0007FFFF, 1, 0, 0x0B},
Package (){0x0007FFFF, 2, 0, 0x0B},
Package (){0x0007FFFF, 3, 0, 0x0B},
Package (){0x000DFFFF, 0, 0, 0x0A},
Package (){0x0014FFFF, 0, 0, 0x0B},
Package (){0x0014FFFF, 1, 0, 0x0B},
Package (){0x0016FFFF, 0, 0, 0x0B},
Package (){0x0016FFFF, 1, 0, 0x0B},
Package (){0x0016FFFF, 2, 0, 0x0B},
Package (){0x0016FFFF, 3, 0, 0x0B},
Package (){0x0017FFFF, 0, 0, 0x0B},
Package (){0x001CFFFF, 0, 0, 0x0B},
Package (){0x001CFFFF, 1, 0, 0x0A},
Package (){0x001CFFFF, 2, 0, 0x0B},
Package (){0x001CFFFF, 3, 0, 0x0B},
Package (){0x001DFFFF, 0, 0, 0x0B},
Package (){0x001DFFFF, 1, 0, 0x0A},
Package (){0x001DFFFF, 2, 0, 0x0B},
Package (){0x001DFFFF, 3, 0, 0x0B},
Package (){0x001EFFFF, 0, 0, 0x0B},
Package (){0x001EFFFF, 1, 0, 0x0B},
Package (){0x001EFFFF, 2, 0, 0x0B},
Package (){0x001EFFFF, 3, 0, 0x0B},
Package (){0x001FFFFF, 1, 0, 0x0B},
Package (){0x001FFFFF, 2, 0, 0x0B},
Package (){0x001FFFFF, 3, 0, 0x0B},
Package (){0x001FFFFF, 0, 0, 0x0B},
dmesg shows no GSI or PCI errors, TPM & touchpad IRQs still work
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1e7a708183ac4170b28da9565137fa2f5088a7eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54683
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since GPIO IO-APIC IRQs are fixed in hardware (RO registers), this patch
allows cannonlake boards to dynamically assign PCI IRQs. This means not
relying on FSP defaults, which eliminates the problem of PCI IRQs
interfering with GPIO IRQs routed to the same IRQ, when both have
selected IO-APIC routing.
Also prodrive/hermes (intel/cannonlake) was the only user of
uart_acpi_write_irq(), therefore use the allocated IRQ instead of the
fixed IRQ number in that function to preserve behavior.
BUG=b:130217151
TEST=on dratini, grep 'IO-APIC' /proc/interrupts (compressed to fit)
0: 11 0 0 0 IO-APIC 2-edge timer
1: 0 661 0 0 IO-APIC 1-edge i8042
8: 0 0 0 0 IO-APIC 8-edge rtc0
9: 0 874 0 0 IO-APIC 9-fasteoi acpi
14: 0 0 1 0 IO-APIC 14-fasteoi INT34BB:00
17: 0 10633 0 0 IO-APIC 17-fasteoi mmc1
19: 0 0 0 0 IO-APIC 19-fasteoi mmc0
22: 0 0 0 0 IO-APIC 22-fasteoi i801_smbus
26: 153738 0 0 0 IO-APIC 26-fasteoi idma64.0, i2c_designwar
27: 0 8 0 0 IO-APIC 27-fasteoi idma64.1, i2c_designwar
30: 0 0 227 0 IO-APIC 30-fasteoi i2c_designware.2
33: 0 0 0 0 IO-APIC 33-fasteoi idma64.3
35: 43107 0 0 0 IO-APIC 35-fasteoi idma64.4, pxa2xx-spi.4
36: 0 0 2039 0 IO-APIC 36-fasteoi idma64.5, pxa2xx-spi.5
45: 0 0 9451 0 IO-APIC 45-edge ELAN0000:00
85: 0 0 0 0 IO-APIC 85-fasteoi chromeos-ec
93: 0 7741 0 0 IO-APIC 93-edge cr50_spi
abbreviated _PRT dump:
If (PICM)
Package () {0x0001FFFF, 0x00, 0x00, 0x10},
Package () {0x0001FFFF, 0x01, 0x00, 0x11},
Package () {0x0001FFFF, 0x02, 0x00, 0x12},
Package () {0x0002FFFF, 0x00, 0x00, 0x13},
Package () {0x0004FFFF, 0x00, 0x00, 0x14},
Package () {0x0005FFFF, 0x00, 0x00, 0x15},
Package () {0x0008FFFF, 0x00, 0x00, 0x16},
Package () {0x0012FFFF, 0x01, 0x00, 0x17},
Package () {0x0012FFFF, 0x02, 0x00, 0x10},
Package () {0x0012FFFF, 0x00, 0x00, 0x18},
Package () {0x0013FFFF, 0x00, 0x00, 0x19},
Package () {0x0014FFFF, 0x00, 0x00, 0x11}
Package () {0x0014FFFF, 0x01, 0x00, 0x12},
Package () {0x0014FFFF, 0x02, 0x00, 0x13},
Package () {0x0014FFFF, 0x03, 0x00, 0x14},
Package () {0x0015FFFF, 0x00, 0x00, 0x1A},
Package () {0x0015FFFF, 0x01, 0x00, 0x1B},
Package () {0x0015FFFF, 0x02, 0x00, 0x1C},
Package () {0x0015FFFF, 0x03, 0x00, 0x1D},
Package () {0x0016FFFF, 0x00, 0x00, 0x15},
Package () {0x0016FFFF, 0x01, 0x00, 0x16},
Package () {0x0016FFFF, 0x02, 0x00, 0x17},
Package () {0x0016FFFF, 0x03, 0x00, 0x10},
Package () {0x0017FFFF, 0x00, 0x00, 0x11},
Package () {0x0019FFFF, 0x00, 0x00, 0x1E},
Package () {0x0019FFFF, 0x01, 0x00, 0x1F},
Package () {0x0019FFFF, 0x02, 0x00, 0x20},
Package () {0x001AFFFF, 0x00, 0x00, 0x12},
Package () {0x001CFFFF, 0x00, 0x00, 0x10},
Package () {0x001CFFFF, 0x01, 0x00, 0x11},
Package () {0x001CFFFF, 0x02, 0x00, 0x12},
Package () {0x001CFFFF, 0x03, 0x00, 0x13},
Package () {0x001DFFFF, 0x00, 0x00, 0x10},
Package () {0x001DFFFF, 0x01, 0x00, 0x11},
Package () {0x001DFFFF, 0x02, 0x00, 0x12},
Package () {0x001DFFFF, 0x03, 0x00, 0x13},
Package () {0x001EFFFF, 0x00, 0x00, 0x21},
Package () {0x001EFFFF, 0x01, 0x00, 0x22},
Package () {0x001EFFFF, 0x02, 0x00, 0x23},
Package () {0x001EFFFF, 0x03, 0x00, 0x24},
Package () {0x001FFFFF, 0x01, 0x00, 0x15},
Package () {0x001FFFFF, 0x02, 0x00, 0x16},
Package () {0x001FFFFF, 0x03, 0x00, 0x17},
Package () {0x001FFFFF, 0x00, 0x00, 0x14},
Else
Package () {0x0001FFFF, 0x00, 0x00, 0x0B},
Package () {0x0001FFFF, 0x01, 0x00, 0x0A},
Package () {0x0001FFFF, 0x02, 0x00, 0x0B},
Package () {0x0002FFFF, 0x00, 0x00, 0x0B},
Package () {0x0004FFFF, 0x00, 0x00, 0x0B},
Package () {0x0005FFFF, 0x00, 0x00, 0x0B},
Package () {0x0008FFFF, 0x00, 0x00, 0x0B},
Package () {0x0012FFFF, 0x01, 0x00, 0x0B},
Package () {0x0012FFFF, 0x02, 0x00, 0x0B},
Package () {0x0014FFFF, 0x00, 0x00, 0x0A},
Package () {0x0014FFFF, 0x01, 0x00, 0x0B},
Package () {0x0014FFFF, 0x02, 0x00, 0x0B},
Package () {0x0014FFFF, 0x03, 0x00, 0x0B},
Package () {0x0016FFFF, 0x00, 0x00, 0x0B},
Package () {0x0016FFFF, 0x01, 0x00, 0x0B},
Package () {0x0016FFFF, 0x02, 0x00, 0x0B},
Package () {0x0016FFFF, 0x03, 0x00, 0x0B},
Package () {0x0017FFFF, 0x00, 0x00, 0x0A},
Package () {0x001AFFFF, 0x00, 0x00, 0x0B},
Package () {0x001CFFFF, 0x00, 0x00, 0x0B},
Package () {0x001CFFFF, 0x01, 0x00, 0x0A},
Package () {0x001CFFFF, 0x02, 0x00, 0x0B},
Package () {0x001CFFFF, 0x03, 0x00, 0x0B},
Package () {0x001DFFFF, 0x00, 0x00, 0x0B},
Package () {0x001DFFFF, 0x01, 0x00, 0x0A},
Package () {0x001DFFFF, 0x02, 0x00, 0x0B},
Package () {0x001DFFFF, 0x03, 0x00, 0x0B},
Package () {0x001FFFFF, 0x01, 0x00, 0x0B},
Package () {0x001FFFFF, 0x02, 0x00, 0x0B},
Package () {0x001FFFFF, 0x03, 0x00, 0x0B},
Package () {0x001FFFFF, 0x00, 0x00, 0x0B},
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I914ac65470635f351d6311dc9b65e8e4d8d8ecfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55968
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:130217151
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If535ad0bdd46d3315493155e64968d305aa34799
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55967
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The IRQ for a single device may be required elsewhere, therefore provide
get_pci_devfn_irq.
BUG=b:130217151, b:171580862, b:176858827
Change-Id: Ibebd821767a2698c9e60b09eeeff3bb596359728
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55826
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The results of the PCI IRQ assignments are used in several places, so
it makes for a nicer API to cache the results and provide simpler
functions for the SoCs to call.
BUG=b:130217151, b:171580862, b:176858827
Change-Id: Id79eae3f2360cd64f66e7f53e1d78a23cfe5e9df
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55825
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Because the FSP interface for PCI IRQs only includes the PCH devices,
this function is the complement to that, taking the list of irq entries,
and programming the PCI_INTERRUPT_LINE registers.
BUG=b:130217151, b:171580862, b:176858827
TEST=boot brya with patch train, verify with `lspci -vvv` that for all
the north PCI devices, their IRQ was either the one programmed by this
function, or an MSI was used.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I81cf7b25f115e41deb25767669b5466b5712b177
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55817
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
